Sirius XM RAdio Lynx LV1 User Manual

LV1 Vehicle Kit User Guide 121214a

Table of Contents

Introduction to Lynx Vehicle Dock ................................................................................................ 3

Vehicle Dock Buttons and Controls .......................................................................................................................................... 3

Remote Control .......................................................................................................................................................................... 5

Remote Control Button Functions ........................................................................................................................................ 5

Remote Control Battery Replacement .................................................................................................................................. 6

Installation ..................................................................................................................................... 7

Choose a location for Lynx ........................................................................................................................................................ 7

Dash Mount Method .............................................................................................................................................................. 7

Vent Mount Method ............................................................................................................................................................... 9

Mount the Magnetic Mount Antenna ..................................................................................................................................... 11

To install the Magnetic Mount Antenna ............................................................................................................................. 11

Route the Magnetic Mount Antenna Cable ............................................................................................................................ 14

Sedan/Coupe With the Antenna Placed at the Rear of the Roof ...................................................................................... 17

Sedan/Coupe With the Antenna Placed at the Front of the Roof ..................................................................................... 18

SUV ........................................................................................................................................................................................ 18

Convertible ............................................................................................................................................................................ 19

Pickup Truck .......................................................................................................................................................................... 19

Connect the Magnetic Mount Antenna and

Power

Connect Power Adapter ....................................................................... 20

Connect the Audio ....................................................................................................................... 23

Activation ..................................................................................................................................... 26

Using the Lynx Vehicle Dock ........................................................................................................ 27

FM Channels ............................................................................................................................................................................. 27

Turning the

Selecting and Setting an FM Channel for

Setting and Replacing FM Presets ....................................................................................................................................... 28

Selecting FM Presets ............................................................................................................................................................ 29

Bluetooth .................................................................................................................................................................................. 30

Brightness ................................................................................................................................................................................. 31

Power

Connect FM Transmitter On or Off ...................................................................................................... 27

Power

Connect .................................................................................................. 27

Audio Level ............................................................................................................................................................................... 32

Auto Off ..................................................................................................................................................................................... 32

Troubleshooting ........................................................................................................................... 34

Advisory Messages ................................................................................................................................................................... 34

Problem Troubleshooting ........................................................................................................................................................ 35

Introduction to Lynx Vehicle Dock

Power

Introduction to Lynx Vehicle Dock

Vehicle Dock Buttons and Controls

The buttons and controls of the Vehicle Dock are identified in the illustration below. The details of each begin below the illustration.

Lock Tab: Secures Lynx in the Vehicle Dock. Push back to release Lynx from the dock.

Knob:

Multifunction: When listening to live Satellite Radio, turn the Knob to enter the Spectrum channel browsing mode,

and scroll through channels.

Press and release the Knob to select a channel and return to the Now Playing screen.

to display the FM Settings screen. Quickly select an FM preset by tapping a saved FM preset at the bottom of the screen.

Connect FM output mode only: When at the Now Playing screen, press and hold the Knob for two seconds

Introduction to Lynx Vehicle Dock

Turn the Knob to select an FM channel frequency. Tap + at the bottom of the screen to save the FM channel as a new preset. Tap+hold an existing preset to replace it with a new FM channel.

AMPS Mounts: Mounting points for Dash Mount. Use the 4 provided screws.

Mounting Point: Mounting Point for Vent Mount.

ANT (Silver): Connection for the Magnetic Mount Antenna.

POWER (Red): Connection for the

AUDIO (Green): Connection for Aux In Cable or optional Cassette Adapter (sold separately).

FM OUT (Blue): Connection for optional FM Direct Adapter (sold separately).

Power

Connect Power Adapter.

Introduction to Lynx Vehicle Dock

Remote Control

Remote Control Button Functions

The buttons of the Remote Control are identified in the illustration below. The details of each begin below the illustration.

Power Button: Press for 3 seconds to turn Lynx On; press and hold to turn Lynx Off.

Pause and Replay Buttons:

Pause/Play button: Pauses or resumes playing of the currently tuned channel.

Rewind button*: Rewinds through content so you can hear-that-again. Tap to rewind to the beginning of a song or

show segment. (Press+hold to continuously rewind through content.**)

Fast-Forward button*: Advances through content until live radio is reached. Tap to advance to the next song or show segment. (Press+hold to continuously fast forward through content.**)

*Internet Radio and Radio Replays for music channels are limited to 1 rewind and up to 5 skip forwards per hour (other channels may have same restrictions). **When listening to Satellite Radio.

Numbers 1-5 Buttons: Selects the corresponding favorite channel in the current favorite channel page on the Now Playing screen.

Numbers 6-0 Buttons: Selects the favorite channel page, i.e., 6=page 1, 7=page 2, etc.

Mute Button: Silences the audio.

Direct Button: Directly tunes a channel by entering the channel number with the number buttons.

Tune Up/Down Channels Buttons: Immediately tunes up or down the channels.

Jump Button**: If configured for traffic/weather, jumps to the traffic/weather for the city you have selected. If

configured for last channel, jumps to the channel to which you had previously been listening.

Power

FM Button ( Settings screen.

Connect only): Advances through the FM presets. If no FM presets have been set, it opens the FM

Introduction to Lynx Vehicle Dock

Remote Control Battery Replacement

To replace the battery in the Remote Control, follow these steps:

1. Turn the Remote Control over and remove the battery cover. It is best if you remove the battery door by

inserting your fingernail in the center of the gap between the door and the back of the remote. Apply a little pressure and the door will pop open.

2. Observe the orientation of the battery, then slide it out. The positive (+) side of the battery should face up,

matching the positive (+) on the battery contact.

3. Replace it with a CR2025 battery.

4. Replace the battery cover.

Installation

Choose a location for Lynx

Installation

For mounting the method. For the Vent Mount, wait until after you have connected all the cables to the Vehicle Dock before you attach it to the mount.

Dash Mount Method

Note: The air temperature needs to be at least 60° F to install the Dash Mount. If needed, turn on the heater in your

vehicle.

1. Select a flat surface for the Dash Mount with ample room for the Vehicle Dock and Lynx. Avoid mounting on

leather surfaces.

Power

Connect™ Vehicle Dock, you can select either the Dash Mount method or the Vent Mount

2. Orient the adhesive foot so that the Vehicle Dock and Lynx are easily accessible. Loosen the knob, adjust the

adhesive foot, and then tighten it again.

Installation

3. Attach the Dash Mount to the

Power

Connect Vehicle Dock using the 4 provided screws.

4. Clean the surface where you are installing the Dash Mount with the alcohol preparation pad.

5. Once the surface is dry, remove the adhesive liner. Press and hold the Dash Mount in place for 30 seconds.

Allow the adhesive to cure for 2-4 hours.

6. You can adjust the dock mounting plate, tilting it in your preferred direction.

Vent Mount Method

1. Select a vent with ample room for Lynx and Vehicle Dock.

Installation

2. Some vents have recessed louvers. If yours are recessed, remove the regular vent clamps and install the

extended vent clamps as shown below.

Installation

3. Install the Vent Mount into the vehicle vent. i. Insert the Vent Mount into the vent opening.

ii. Push until hooked on the rear of the vent louver. Rest the foot against the bottom of the vent.

iii. If necessary, adjust the tilt of the Vent Mount by repositioning the foot to a different tilt adjustment

hole.

4. Do not attach the Vehicle Dock to the mount at this time.

Installation

Mount the Magnetic Mount Antenna

Mount the Magnetic Mount Antenna on the outside of your vehicle, on a horizontal surface that will always face the sky. The antenna contains a strong magnet which will stick to any metal part of your vehicle, but will not damage the vehicle.

To install the Magnetic Mount Antenna

1. Choose the best location for your antenna for your type of vehicle. Pay particular attention to any accessories

that you may have like luggage or ski racks, and how frequently you may use them.

Note: Consult a professional installer if your vehicle roof or hood is non-metallic (i.e., fiberglass), or if

you have difficulty finding a location for your antenna.

Sedan/Coupe: We recommend mounting the antenna just above either the front windshield or the back window as shown.

SUV: We recommend mounting the antenna at the rear of the roof as shown.

Convertible: We recommend mounting the antenna at the leading edge of the trunk as shown.

Pickup Truck: We recommend mounting the antenna just above the front windshield as shown.

Installation

2. Clean the surface of the selected mounting location using the alcohol preparation pad and let it dry

thoroughly.

3. If you are installing the antenna at the roof edge, or hood edge, install the Cable Routing Adapter to direct the

antenna cable downward.

4. Place the antenna in the location you selected. Review the following tips and cautions.

Tip: Mount the antenna on the roof (for most vehicles) or trunk (for convertibles) where it has a clear view

of the sky in all directions.

Installation

Caution: Don’t mount the antenna inside the vehicle, for example, on the dashboard.

Caution: Don’t mount the antenna on any of the vehicle’s front, back or side pillars

Caution: Don’t mount the antenna close to a roof rack. Adjust the rack so it’s further away from the

antenna or move the antenna closer to the center of the roof.

Caution: Don’t mount the antenna close to another antenna. Mount it at least 3 inches away.

Installation

Route the Magnetic Mount Antenna Cable

Before you begin routing the antenna cable, read the general instructions which follow concerning how to route and hide the antenna cable. Then route your antenna cable according to the more specific instructions which follow these, for your specific type of vehicle.

Tip: Always be careful to include enough slack in your cable to accommodate open doors or trunk lids. Use things

typically found around the home, like electrical tape, to secure cables in areas so that hinges do not pinch the cable with the door. Hide any excess cable in the trim.

General Instructions:

Installation

Vehicle Specific Instructions:

Sedan/Coupe With the Antenna Placed at the Rear of the Roof

1. Feed the antenna cable from the antenna underneath the rubber molding around the rear window. Use a

blunt plastic putty knife or similar blunt tool to lift the rubber molding around the rear window and tuck the antenna cable underneath the molding. Route the antenna cable around and down the window to the lowest point. If your rear window does not have rubber molding, we recommend consulting a professional installer.

2. Route the antenna cable out of the window molding and into the rubber weather stripping around the trunk

opening. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. To avoid sharp bends in the cable, run the cable inside the weather stripping for a few inches, then remove the cable from the weather stripping inside the trunk. Keep the cable away from hinges, gears, etc., that could damage it.

3. Route the cable out from the rubber weather stripping and along the trunk wall. Continue routing the cable

into the vehicle cabin through a conduit or along an existing wiring harness.

4. Route the cable through the main cabin area under the interior trim, towards the front of the vehicle. Use a

blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable underneath. Avoid side airbag locations on back pillars and above the doors. Airbag locations are marked with “SRS” logos. Be careful not to crimp or cut the cable.

5. Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the

dashboard or console. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Be careful not to kink the cable. Secure the excess cable with wire ties (purchased separately).

Installation

6. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you

can easily connect it to the antenna connector of the dock.

Power

7. Continue with the next section, Connect the Magnetic Mount Antenna and

Sedan/Coupe With the Antenna Placed at the Front of the Roof

1. Feed the antenna cable from the antenna underneath the rubber molding around the windshield. Use a blunt

plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath the molding. Route the antenna cable around and down the windshield to the lowest point.

2. At the lowest corner of the windshield, route the cable out of the windshield molding and into the rubber

weather stripping around the door opening. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. Run the cable inside of the weather stripping to the bottom of the door opening.

Connect Power Adapter.

3. Pull the cable out of the weather stripping at the bottom of the door opening and route it under the carpet

toward the dashboard. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Be careful not to kink the cable. Secure the excess cable with wire ties.

4. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you

can easily connect it to the antenna connector of the dock.

Power

5. Continue with the next section, Connect the Magnetic Mount Antenna and

SUV

1. Feed the antenna cable underneath the rubber weather stripping of the rear tailgate window/door and route

the cable along the rear hatch. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. Pull the cable out from weather stripping and route it into the cabin under the interior trim. Avoid hinges or gears that could crimp or cut the cable.

2. Route the cable through the SUV’s main cabin area under the interior trim, towards the front of the vehicle.

Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable underneath. Avoid side airbag locations on back pillars and above the doors. Airbag locations are marked with “SRS” logos. Be careful not to crimp or cut the cable.

Connect Power Adapter.

3. Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the

4. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you

can easily connect it to the antenna connector of the dock.

Installation

5. Continue with the next section, Connect the Magnetic Mount Antenna and

Convertible

1. Bring the antenna cable from the antenna into the trunk at the front edge of the trunk lid. Keep any bends in

the cable loose. Tape or tie the cable along the inside of the trunk lid to the trunk lid hinge strut.

2. Allow enough slack in the cable so the trunk lid can easily open and close and keep the cable away from

hinges, gears, etc., that could crimp or cut it. Route the cable along the trunk wall and into the cabin through a conduit or along an existing wiring harness.

3. Route the cable through the main cabin area under the interior trim, towards the front of the vehicle. Use a

4. Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the

Power

Connect Power Adapter.

5. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you

can easily connect it to the antenna connector of the dock.

Power

6. Continue with the next section, Connect the Magnetic Mount Antenna and

Pickup Truck

1. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck

the antenna cable underneath it.

2. Continue tucking the cable underneath the windshield molding around the windshield to the lowest corner.

3. At the lowest corner of the windshield, route the cable out of the windshield molding and into the rubber

4. Pull the cable out of the weather stripping at the bottom of the door opening and route it under the carpet

Connect Power Adapter.

5. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you

can easily connect it to the antenna connector of the dock.

Installation

Power

6. Continue with the next section, Connect the Magnetic Mount Antenna and

Power

Connect Power Adapter.

Connect the Magnetic Mount Antenna and

1. Plug the Magnetic Mount Antenna into the silver ANT connector on the

2. Plug the

Power

Connect Power Adapter into the red POWER connector on the dock.

Connect Power Adapter

Power

Connect Vehicle Dock.

3. Insert the

4. Place Lynx into the Vehicle Dock and press the Power button for 3 seconds.

Power

Connect Power Adapter into your vehicle’s cigarette lighter or power adapter socket.

Installation

Note: Wait until you have connected the audio before you connect the Vehicle Dock to the Vent Mount.

5. If you are prompted to set the time Zone, tap Change timezone, and select your time zone. Tap OK, then tap

Continue. The default time zone is set to Eastern Standard Time.

6. If you are prompted to take the tour, tap No thanks.

7. At the next screen tap Continue to be guided through the activation process.

Installation

8. Be sure the vehicle is parked in a safe place outside, with a clear view of the sky, and tap Continue.

9. If Lynx displays Signal Found, tap Continue and proceed with connecting the audio in the next section.

10. If Lynx displays No Signal/Check Antenna, reposition the vehicle so that nothing is blocking the antenna’s

clear view of the sky, and tap Continue to try again

Continue with the next section, Connect the Audio

Connect the Audio

To play audio through your vehicle’s stereo or FM radio, decide on one of the following audio connection options.

Option 1: Best: Aux In Cable: If your vehicle radio has an AUX jack, the Aux In Cable connects Lynx to your vehicle radio for the audio. Refer to your vehicle’s owner’s manual to find the location of the auxiliary input jack, or consult the vehicle dealer.

Important: If the Aux In Cable is connected to the Vehicle Dock,

be turned off. If you want to use either of these audio connections, you must unplug the Aux In Cable.

Tip: The auxiliary input jack may be located on the face plate of the vehicle radio, on the back of the radio,

anywhere on the front dash panel, inside the glove compartment, or inside the center console in between the front seats.

Option 2: Best: Bluetooth: If your vehicle has can connect it with Lynx for audio. Lynx is not compatible with the Hands Free Profile (HFP), which is typically used for a Bluetooth connection to a cell phone. Refer to the Lynx Quick Start Guide for additional information on connecting the audio using

Option 3: Good: Cassette Adapter: Use a Cassette Adapter if your vehicle has a built-in cassette player. Cassette Adapters are sold separately and can be purchased from an electronics retailer, or go to

www.siriusxm.com/accessories

Bluetooth

and select XM accessories.

Bluetooth

stereo audio streaming compatibility (A2DP Profile), you

Bluetooth

and PowerConnect FM outputs will

Connect the Audio

Option 4: Good: PowerConnect: Use the PowerConnect feature of Lynx. PowerConnect plays the audio through your vehicle’s FM radio.

Option 5: Better: FM Direct Adapter: Use the FM Direct Adapter. If none of the previous three audio connection options will work in your vehicle, then you will need to use the FM Direct Adapter (FMDA) (sold separately). The FMDA needs to be installed by a professional installer and directly connects the Radio to your vehicle’s FM radio. To learn more, check with the retailer where you bought your Lynx, or go to www.siriusxm.com/accessories XM accessories.

To connect the audio, follow these instructions:

1. The Audio check screen should be displayed. If you cannot hear the audio playing, tap No.

and select

2. You will be prompted to continue with the audio setup. Tap Continue.

3. At the How will you connect your audio? screen, select your desired audio connection and tap Continue.

Connect the Audio

4. From this point, continue to follow the on-screen instructions until you reach the Activation screen.

5. You should now be hearing the SiriusXM audio. Connect the Vehicle Dock to the Vent Mount, if you are using

the Vent Mount. Continue with the next section, Activation Radio.

, if you are not yet subscribed to SiriusXM Satellite

Should you should change your type of audio connection at a later time, you can adjust the settings by tapping Home

, tap , tap Settings , tap Display, audio & power, and tap Vehicle Dock. To change to a

for instructions.

here

Bluetooth

connection, tap

Activation

To be able to tune the channels, you will need to subscribe to SiriusXM Satellite Radio. Once you have successfully connected the audio, keep your vehicle parked where it has a clear view of the sky throughout the activation process. Follow the instructions on the screen to subscribe.

A. To subscribe to SiriusXM Satellite Radio, you will need the Radio ID which can be found:

• on the Activation screen

• by tuning to channel 0

• on a label on the bottom of the gift box

• on the label inside the rear cover of Lynx

Note: The Radio ID does not use the letters I, O, S, or F.

B. Lynx should be displaying the Activation screen. To subscribe:

• By phone: US residents call 1-866-635-2349, Canadian residents call 1-877-438-9677

• Online: US residents go to www.siriusxm.com/activatenow

www.xmradio.ca/activate

C. Activation usually takes 10 to 15 minutes after you have completed the subscription process, but may take up

to an hour. We recommend that your Radio remain on and in the Vehicle Dock until subscribed. Lynx will display a Subscription Updated message when it receives the activation signal. Once subscribed, you’ll be able to tune to the channels in your subscription plan.

Hardware and subscription sold separately. Service will automatically renew for additional periods of the same

length as the plan you choose, on the subscription package you choose (which may differ from the package which arrived with the radio) until you call us at 1-866-635-2349 to cancel. See our Customer Agreement for complete terms at www.siriusxm.com

subject to change. For residents in Canada, see our Customer Agreement for complete terms at www.siriusxm.ca.

. Activation fee and other fees and taxes apply. All fees and programming are

, Canadian residents go to

Using the Lynx Vehicle Dock

Power

FM Channels

Using the Lynx Vehicle Dock

Turning the

Note: If anything is plugged into the AUDIO connection of the Vehicle Dock,

be disabled and you will be unable to turn it on.

There are two ways to turn the

A. Press and hold the Knob on the Vehicle Dock until the FM Settings screen is displayed. Tap the check box in

the upper right corner of the screen to toggle the FM transmitter on or off.

B. Tap Home

FM transmitter On/Off to toggle it on or off.

Connect FM Transmitter On or Off

Bluetooth

Power

Connect FM transmitter in Lynx or off.

, tap , tap Settings , tap Display, audio & power, tap Vehicle Dock, and tap PowerConnect

and the FM transmitter will

Selecting and Setting an FM Channel for

There are two ways to find a suitable FM channel for use with the

A. Use the SiriusXM FM Channel Finder at www.siriusxm.com/fmchannel

code. The Channel Finder will suggest a list of available FM channels in your area. For convenience, write down or print out the list.

B. Manually tune through your local FM channels on your vehicle’s FM radio. Locate and create a list of channels

that aren’t being used by any FM radio station. Write down the list. Once you have created your list of available FM channels, you will need to use the one that provides the best match for Lynx.

Connect

Power

Connect audio connection option:

. Go to the website and enter your zip

Using the Lynx Vehicle Dock

You’ll need to use the ‘Manual’ tune function on your vehicle’s FM radio to tune through the FM channels oneby-one. Turn on your vehicle’s FM radio. Start at 88.1 and use the ‘Manual’ tune function on your vehicle’s FM radio to tune through each FM channel one-by-one to locate channels that aren’t being used by a local FM radio station. Write down each FM channel that has only static or silence on it, until you reach 107.9.

Once you have located several FM channels to try, set your vehicle FM radio and Lynx to the same FM channel:

1. Tune the vehicle FM radio to the first FM channel.

2. Tune Lynx to the same FM channel. Press and hold the Knob on the Vehicle Dock until the FM Settings

screen is displayed.

3. Turn the Knob, or tap

a FM preset, tap +, or tap+hold any other existing FM preset to replace it.

4. Tap Back

Tip: If anything is plugged into the AUDIO connection of the Vehicle Dock, the FM transmitter will be disabled.

5. If the selected FM channel doesn’t sound the best, work down the list of FM channels until you find one with

which you are satisfied. Repeat steps 1 - 4.

Setting and Replacing FM Presets

Setting multiple FM presets is useful if you drive some distance, and the FM channel you are using begins to have interference. You can simply select another FM channel you have set as a FM preset with a tap of the Knob. To set multiple FM presets, or to replace FM presets:

1. Press and hold the Knob on the Vehicle Dock until the FM Settings screen is displayed, or tap Home

, tap Settings , tap Display, audio & power, tap Vehicle Dock, and tap PowerConnect FM transmitter

On/Off.

. You should hear the SiriusXM audio playing through your vehicle FM radio.

or , to match the same FM channel as the vehicle FM radio. If you wish to save it as

, tap

Using the Lynx Vehicle Dock

2. Turn the Knob, or tap

3. Tap + to save the FM channel as a preset, or tap+hold an existing FM preset to replace it with the new FM

channel.

or , to select the desired FM channel.

4. You can continue to set FM presets, up to a maximum of 4. When you have completed setting FM presets, tap

Back

Selecting FM Presets

If you have set multiple FM presets, you can quickly tune to a new FM channel using the FM preset:

1. Press and hold the Knob on the Vehicle Dock until the FM Settings screen is displayed.

2. Tap an FM preset to immediately tune to the FM channel.

3. Tap Back

, or wait a few moments for the screen to time-out.

Using the Lynx Vehicle Dock

Bluetooth

You can connect to your vehicle stereo system if it is stereo audio streaming (A2DP Profile) compatible. Lynx is not compatible with the Hands Free Profile (HFP), which is typically used for a

To connect your vehicle stereo system, you’ll need to pair and connect it with Lynx. You’ll need to know how to place your vehicle stereo system in

To pair and connect, follow these steps.

Bluetooth

discoverable mode, and may also need the

Bluetooth

connection to a cell phone.

Bluetooth

passcode.

1. Tap Home

2. In the Bluetooth devices menu, if Bluetooth On/Off does not have a check mark, tap Bluetooth On/Off to

turn it on. A check mark will appear in the box at the right once

3. If necessary, consult the instructions for your vehicle stereo system, and place it in

discoverable/pairing mode.

4. From the Bluetooth Devices menu tap Scan for devices. Allow Lynx to scan for a few moments for

Bluetooth

, tap , tap Connect .

Bluetooth

is turned on.

Bluetooth

devices. If Lynx found your vehicle stereo system, its name will be listed below

Bluetooth

devices.

5. Tap the name in the menu and Lynx will attempt to pair. (You may be prompted for the passcode for your

device. If so, enter the passcode.) If pairing is successful, the Paired but not connected message will be displayed below the name.

6. Tap the name again to connect. You will be prompted that Bluetooth is connected, and asked if you always

want to automatically connect to the vehicle stereo system when Lynx is in the vehicle dock (default = yes). Tap OK, or tap the check box to remove the check mark if you do not wish to have an automatic connection.

7. Tap your

message will be displayed below your playing through your

Brightness

Bluetooth

Using the Lynx Vehicle Dock

device name again and Lynx will connect to the device. If successful, the Connected to...

Bluetooth

device.

device name. You should now hear the SiriusXM audio

Brightness adjusts the brilliance of the display screen, and the brightness of the blue LED light on the Vehicle Dock. You can manually adjust the brightness, or have Lynx adjust the brightness automatically according to the ambient light.

There are two ways to access the brightness control when Lynx is in the Vehicle Dock:

• Tap the Power button.

• Tap Home

If you wish to manually adjust the brightness, tap the checkbox next to Automatic brightness.

Drag the sliders left or right to adjust the brightness, or tap Automatic brightness. When set, tap OK.

, tap , tap Settings , tap Display, audio & power, tap Vehicle Dock, and tap Brightness.

Using the Lynx Vehicle Dock

Audio Level

Audio level allows you to adjust the volume of Lynx to match the audio output level of your vehicle’s FM radio or CD player, so that when you switch between them, you don’t have to adjust the stereo volume up or down. Audio level should not be used as a volume control, but as an adjustment control.

Access the Audio level control by tapping Home Audio level. Adjust the audio level by dragging the slider left or right. When set, tap Done.

, tap , tap Settings , tap Locations, tap Vehicle Dock, and tap

Auto Off

Auto off sets the amount of time before Lynx turns itself off. This is useful if you exited your vehicle without turning Lynx off, to avoid draining the vehicle battery. Choices are Never (default), 30 minutes, or 1, 2, or 3 hours. If Auto off is On, and you touch any of the controls, or the display screen, the Auto off countdown will reset, and begin over again.

Access the Auto off control by tapping Home and tap Auto off. Scroll up or down, and tap the desired time.

, tap , tap Settings , tap Display, audio & power, tap Vehicle Dock,

As Lynx is about to turn off, you will be alerted with a countdown. If you wish Lynx to remain on, tap Cancel.

Using the Lynx Vehicle Dock

Troubleshooting

Advisory Messages

Message Explanation

Check Satellite Antenna

No Satellite Signal

Satellite Radio not available

Waiting for Satellite initialization

Unsubscribed channel

Game Alert memory full

Show Alert memory full

The satellite antenna is not connected to the dock. Connect the satellite antenna to the ANT connector on the dock.

Lynx is not receiving the satellite signal from the satellite antenna.

Verify that the antenna is correctly mounted on the vehicle, and that nothing is blocking the view of the sky.

Make sure that the antenna cable is firmly and securely plugged into the dock, and that the antenna cable is not bent or broken.

Turn Lynx Off, then On, to reset this message.

If this message persists, the antenna cable may have been damaged. Replace the antenna.

To listen to Satellite Radio, Lynx has to be in a powered dock, with a properly installed Satellite Radio antenna connected and correctly aimed.

Lynx is initializing and acquiring the Satellite Radio signal. Wait a moment for initialization to complete, and Lynx will begin playing Satellite Radio.

You have attempted to tune to a channel which is not in your subscription plan. Upgrade your subscription, or tune to a channel in your subscription plan.

You have attempted to add more than 100 Show Alerts or Game Alerts. Game and Show alerts are limited to 100 each. Delete some old alerts before adding new ones.

Initializing Shows & On Demand

Shows & On Demand is OffLine

This channel is locked

Please wait Lynx is busy with a task. Wait a moment for Lynx to finish.

Preparing media The microSD card is being formatted. Wait for the formatting to finish.

Pending Broadcast

Shows & On Demand is being prepared for viewing. Wait a moment for initialization to complete.

You have selected to view the Shows & On Demand guide for a listening mode which is not currently connected (satellite or Internet Radio). Some of the information in the guide may not be up to date.

You have enabled Parental Control for channels with mature content (xL). Tap and enter your Lock Code to listen to the channel.

You have selected to listen to traffic and weather, but the traffic/weather for your selected city isn’t being broadcast at the moment. Lynx will automatically tune the traffic and weather when the broadcast begins.

Message Explanation

System updates are available

Troubleshooting

SiriusXM has a system update for Lynx. Tap OK to install the system update, which will take several minutes, or tap Remind Later to install it at another time.

When a system update is available, you can install it anytime by tapping Home and tap OK to install the update.

, tap , tap Settings , tap About Lynx, tap System update,

Updating

Problem Troubleshooting

Problem Solution

Lynx will not turn on.

The satellite icon on the home screen is gray, and I cannot select it.

I can only tune to channels 0 and 1 on Satellite Radio.

I don’t receive all the Satellite Radio channels to which I subscribed.

Lynx is applying a software update. Do not power Lynx off until the updated has completed.

Is the battery installed in Lynx? Lynx will not turn on without the battery installed. Install the battery.

The battery may be too discharged to power Lynx. Charge the battery, then trying turning Lynx on.

A gray icon indicates that the service is currently unavailable.

For Satellite Radio, Lynx must be in a dock, with the satellite antenna connected.

Have you already activated your Lynx Satellite Radio subscription? If not, refer to the Activation

If you have already activated your Lynx Satellite Radio subscription, your Lynx may not have received the activation signal. While Lynx is on and playing Satellite Radio, go to http://www.siriusxm.com/refresh and enter the Radio ID of your Lynx. (For Canadian residents, go to

http://refresh.xmradio.ca.) Once you have entered the Radio ID, the

subscription information will be sent to your Lynx within 5 minutes. Lynx will display a Subscription Updated message when it receives the activation signal.

section.

Not all the channels on Internet Radio are on Satellite Radio.

You can find the Radio ID of your Lynx by tapping Home , tap , tap Settings

The channel lineup differs slightly between Satellite Radio and Internet Radio.

Go to www.siriusxm.com/channellineup available on SiriusXM Satellite Radio and Internet Radio.

, and tap My Account.

to view the channels

Troubleshooting

Problem Solution

Lynx Bluetooth does not show my vehicle’s stereo system.

Tune Start does not work.

Tune Scan does not work

Bluetooth

Is Fi & Bluetooth, and tap Bluetooth On/Off to turn it on.

Is Airplane mode on? Tap Home & Bluetooth, and tap Airplane mode On/Off to turn it off.

Is your vehicle stereo system Consult the owner’s manual. Lynx audio streaming devices (A2DP Profile), but is not compatible with the Hands Free Profile (HFP), which is typically used for a connection to a cell phone.

You may have to set your vehicle stereo system into pairing/discoverable mode for Lynx to find it. Consult the owner’s manual for the vehicle, and set the stereo system in pairing/discoverable mode.

Have you turned off the Tune Start feature? Tap Home Settings it on.

Tune Start is only available for music channels.

The Tune Scan feature is only available for Satellite Radio. Tune Scan requires that at least 2 music channels are stored as favorites on the current Now Playing screen. It may take a few minutes to begin after tapping Tune Scan as it needs time to buffer content from the favorite channels.

turned on? Tap Home , tap , tap Settings , tap Wi-

, tap , tap Settings , tap Wi-Fi

Bluetooth

, and tap My content, and tap Tune Start On/Off to turn

device A2DP compatible?

Bluetooth

is compatible with stereo

Bluetooth

, tap , tap

Tune Mix does not work

Tune Mix seems to cut off the end of some songs

Start Now is grayed out when I listen to Satellite Radio.

Some channels are missing from the channel lists.

The Tune Mix feature is only available for Satellite Radio. Tune Mix requires that at least 2 music channels are stored as favorites on the current Now Playing screen. It may take a few seconds to begin after tapping Tune Mix, as it needs time to buffer some content from the favorite channels. The initial song may not always start from the beginning.

This is a normal as Tune Mix is attempting to mix songs from different channels.

The Start Now feature is available only for Internet Radio.

Did you hide channels? Hidden channels are not shown in any channel lists. Consult the Lynx User Guide for more information.

Troubleshooting

Problem Solution

Lynx is not saving any Radio Replays.

Lynx does not save Radio Replays from all my favorite channels.

I never get any Featured Favorites.

I don’t receive any Show Alerts.

I don’t receive any Game Alerts.

Have you turned on the Radio Replays feature? Tap Home tap Settings turn it on.

Radio Replays are saved while listening to Satellite Radio.

Have you saved any favorite channels? Radio Replays are saved from the favorite channels currently displayed on the Now Playing screen, and also from one favorite channel designated as a Preferred Channel.

Some channels are ineligible for Radio Replays.

Have you turned off the Featured Favorites feature? Tap Home

, tap Settings , tap My content, and tap Featured Favorites

On/Off to turn it on.

Featured Favorites are received when listening to Satellite Radio.

Have you set any Show Alerts and/or Game Alerts? Consult the Lynx User Guide for more information.

Have you turned off the alert notification feature?

For Show Alerts, Tap Home content, and tap Show Alert On/Off to turn it on.

For Game Alerts, Tap Home content, tap Game Alert, and tap Sports Alerts to turn it on.

, tap My content, and tap Radio Replays On/Off to

, tap , tap Settings , tap My

, tap ,

, tap

I forgot my Lock Code.

I copied my songs to the microSD card but some songs do not show in the list.

Lynx stays on when I turn off my vehicle

The Lock Code cannot be recovered. It can only be removed by setting Lynx back to the factory defaults.

Note: When you do a factory reset, all configuration changes and

adjustments you have made will be reset. All favorite channels, all show and game alerts, and all Radio Replays will be deleted. Use with caution.

Tap Home Reset all settings to reset Lynx to the factory defaults.

Certain music file formats, and all music files with DRM, are not compatible with Lynx. Consult the Lynx User Guide for more information.

Your vehicle’s power port may not switch off with the vehicle ignition. Unplugging the Power Adapter will turn off Lynx. You can also use the Auto-Off feature in the Settings menu to have Lynx automatically turn off after a period of inactivity. Tap Home tap Vehicle Dock, tap Auto off and choose one of the time options.

, tap , tap Settings , tap Reset & erase, and tap

, tap , tap Settings ,

Sirius XM RAdio Lynx LV1 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual