Page 1
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
1
SIRIUS Bar Moving Head COB 60W RGB 4in1
USER MANUAL TS106
Page 2
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
2
For your own safety, please read this user manual carefully before you initially start-up
Every person involved with the installation, operation and maintenance of this device has to:
-Be qualified.
-Follow the instructions of this manual.
-Consider this manual to be part of the total product.
-Keep this manual for the entire service life of the product
-Pass this manual on to every further owner or use of the product.
-Download the last version of the user manual from the internet in www.triton-blue.com
Unpacking
Thank you for purchasing this Product. Every Product been thoroughly tested and has been transported in
perfect operating condition. Carefully check the carton for damage that may have occurred during
transporting. lf the carton appears to be damaged, carefully inspect your fixture for any damage and be
sure all accessories necessary to operate the unit has arrived intact. carefully unpack the carton, check
the contents to ensure that all parts are present, and have been received in good condition.
AC Power
This fixture has an auto-switching power supply that can accommodate a wide range of input voltages.
The only thing necessary to do before powering on the unit is to make sure the line voltage you are
applying is within the range of accepted voltages. This fixture will accommodate between 100V and 240V
AC 50-60 Hz. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat
(variable resistor or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%
switch.
Safety Precautions
Please read these instructions carefully, which includes important information about the installation, usage
and maintenance of this product.
Please keep this User Guide for future consultation. lf you sell the unit to another user, be sure that they
also receive this instruction booklet.
Do not spill water or other liquids into or on to your unit. Be sure that the local power outlet match that of
the required voltage for your unit.
Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove
or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
INTRODUCTION
The specification
Rate voltage: AC100V～240V 50-60HZ
Rate power: 90W
Light source: 60W RGB COB LED
LED drive current: R:1A G:1A B:1A
Beam angle: 25°
IP class: IP20
DMX channels: 8/13 DMX Channels
Packing Dimensions: 168x164x241mm
Net weight: 3.1Kg
Page 3
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
3
Features
3 PIN male XLR and 3 PIN female XLR
Power Connection: Locking IEC
3 control models:DMX512、sound control 、master/slave
Black plastic
LED display
Indoor operation temperature：-20°C～+40°C
2 DMX models： 8/13 DMX channels
Dimmer:0-100%
Pan:540 degree, Tilt:220degree
Fan cooling (Fan will change speed with temperature)
Temperature detection system（The machine doesn't work if the temperature detection error happened.）
Max power consumption：90W
Page 4
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
4
INSTALLATION
Installation requirement
The equipment can be used in various situation, it can be hung and stand
Choose suitable situation to place or hang the equipment for installation. Make sure to use professional
clamp and screws as hanging the equipment. and be sure that weight of the equipment is within range which
installation area bear
Be sure this equipment is kept at least 0.5m away from any flammable material in installing
Make sure the equipment is installed by qualified person. Any wrongful installation can cause personal injury
or material damage
Please prevent other people from being under installation area, and use suitable and stable terrace in
installing or repairing
The equipment must be placed at ventilated situation and is kept at 50m away from the ground
Power connection
he equipment has an auto-switching power supply that can accommodate a wide range of input voltages。
he only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is
within the range of accepted voltages. This equipment will accommodate between 100V and 240v AC 5060HZ.
DMX serial Data Link
1. Connect the (female) 3 pin connector side of the DMX cable for the first equipment to the output (male)
3pin connector of the DMX cable for the controller
2. Connect the (male) 3 pin connector side of the DMX cable for the first equipment to the output( female)
3pin connector side of the DMX cable for next equipment and so on and so on
Cable
Connection
PIN
Brown
AC live wire
1
blue
AC zero curve
2
green/yellow
AC ground wire
3
Page 5
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
5
OPERATION STEP
Control Panel Function
Button
Function
MODE
Exits from the current menu or function
ENTER
Enables the currently displayed menu or sets the currently selected
value in to the selected function
UP
Navigates upwards through the menu list and increases the
number value when in a function
DOWN
Navigates downwards through the menu list and reduces the
number value when in a function
Menu map
Page 6
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
6
Menu ：
[DMX Address Setup]
Press MENU，and then press UP or DOWN，until it shows the Address Menu,，press ENTER .
Change the DMX address by pressing UP or DOWN，press “ENTER” to keep current setting DMX
address。
[Setup Channel Modes]
Press MENU，and then press UP or DOWN，press ENTER to exit when it shows Control Mode Menu.
Press UP or DOWN to choose 8CH、 13CH DMX mode.
Press UP or DOWN to choose modes, and then press ENTER to save channels.
[Master and Slave Modes]
Press MENU，and then press UP or DOWN，until it shows SLav Mode Menu，press ENTER 。
Choose SLav, Master can according press UP or DOWN SLav、NaSt, press ENTER to SLav。
If choosing Slave, synchronized operation when the signal set out. If choosing Master, then AUTO or
Sound as the master，sends a signal to the from machine synchronous operation since or acoustic control
program
[Auto mode ]
Press MENU，and then press UP or DOWN，press ENTER when it shows Auto Menu.
Choose Auto .Press ENTER to the selected modes. This function as the master use
[Auto mode ]
Press MENU，and then press UP or DOWN，press ENTER when it shows SoUn Menu.
Choose SoUn. Press ENTER to the selected modes. This function as the master use。
[Pan direct and inverse set up]
Press MENU，and then press UP or DOWN，press ENTER when it shows Pan Menu.
Choose the pan direct and inverse set up by pressing UP or DOWN.
[Tilt direct and inverse set up]
Press MENU，and then press UP or DOWN，press ENTER until it shows the Tilt Inverse.
Press UP or DOWN to choose vertical direct and inverse，
[ Software version]
Press the MENU button, then press the UP or DOWN button, until the ver menu is displayed, and then
press ENTER to display the software version vxx.
Page 7
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
7
[System Reset]
● Press MENU，and then press UP or DOWN until it shows the System Reset，press ENTER,the whole
machine reset.
DMX Channel Table
13 CH
CH
Value
Function
1
0-255
PAN 0-540º
2
0-255
PAN 16 bit
3
0-255
Tilt 0-220º
4
0-255
Tilt 16 bit
5
0-255
Pan &Tilt Speed(from fast to slow )
6
0-255
Dimmer 0-100%
7
0-255
Red 0-100%
8
0-255
Green 0-100%
9
0-255
Blue 0-100%
10
0-35
CTC Function Invalidate
36-55
Color temperature selection White=3200K
56-75
Color temperature selection White=3400K
76-95
Color temperature selection White=4200K
96-115
Color temperature selection White=4900K
116-135
Color temperature selection White=5600K
136-155
Color temperature selection White=5900K
156-175
Color temperature selection White=6500K
176-195
Color temperature selection White=7200K
196-215
Color temperature selection White=8000K
216-235
Color temperature selection White=8500K
236-255
Color temperature selection White=10000K
11
0-14
No function
15-255
Macro color
12
0-9
No function
10-140
Strobe in the line(from slow to fast )
141-255
Strobe follow the equipment(from slow to fast )
0-20HZ
13
0-99
sound control close
100-199
sound control open
200-255
Keep 5 seconds, the system reset.
8 CH
CH
Value
Function
1
0-255
PAN 0-540º
2
0-255
Tilt 0-220º
3
0-255
Pan &Tilt Speed(from fast to slow )
Page 8
User Manual | Sirius Bar Moving Head COB 60W RGB 4in1| Rev.Jan. 2014 | www.triton-blue.com
8
4
0-255
Dimmer 0-100%
5
0-255
Red 0-100%
6
0-255
Green 0-100%
7
0-255
Blue 0-100%
8
0-9
No function
10-140
Strobe in the line(from slow to fast )
141-255
Strobe follow the equipment (from slow to fast ) 0-20HZ
Loading...