Sirio Antenne New Vector 4000 Quick Start Manual

Insert the aluminium tube

Æ

10x1400 (19) into the

assembled cone tubes

Æ

13x1400 (17). Pull out the
top tube for 1310 mm and lock
it using the 3.9x12.7mm
phillips tapping screws (14).

Æ

25

24

24

MOUNTING INSTRUCTIONSMOUNTING INSTRUCTIONS

19

77

mm
0
1

13

14

17

99

Pull out the 5 sections of
telescopic aluminium
whip (24) and lock them
using the 3.9x9.5mm
phillips tapping screws
(25).

Æ

1111

24

20

Mount the 4 pcs of the
aluminum ring (20) and
lock them using M5x16
hexagon head screw (3),
M5 washer (4) and M5
hexagonal nut (5).

21

L3

22

9

8

7

20

5

4

Insert the top section with
the cage (21) at L3 (see
tuning table for
frequency) and lock it
using the M4x4 hexagon
socket set screw cup
point (22) and 2mm
hexagonal key (23).

23

UHF female connector

19

3

1010

1212

NEW VECTOR 4000NEW VECTOR 4000

88

3/4 l Base station antenna working on CB and 10m band.
Made of telescopic anti-corodal aluminium tubes. Its long and
robust whip allows perfect performances and very good
connections at long distances too.

TECHNICAL DATA

Electrical Data

Type
Frequency range
Impedance
Radiation ( H-plane)
Polarization
Gain
Bandwidth @ SWR £ 2)
SWR @ res. freq.
Max Power

Feed system
Connector

Mechanical Data

Materials
Wind resistance
Length (approx.)
Weigth (approx.)
Mounting Mast

27...28.5 MHz CB & 10m band Base Station Antenna

DESCRIPTIONDESCRIPTION

SPECIFICATIONSSPECIFICATIONS

: 3/4 l Coaxial J-pole
: 27...28.5 MHz tunable
: 50 W
: 360° omnidirectional
: Vertical
: 2 dBd, 4.15 dBi
: ³ 1400 KHz (120 channel)
: £ 1.2
: 1000 Watts continuous
3000 Watts short time
: Gamma match
: UHF-female

: Aluminium, Steel, Brass, Nylon
: 130 Km/h
: 8480 mm
: 4700 gr
: Æ 35-42 mm

25

25

Insert the fully assembled
telescopic whip into the
second section of tube

10

B Copyright SIRIO antenne - Technical Data are subjected to change - Printed in ITALY - Rev. 06/03/2009 - Cod. ID041, pag. 4/4

(10) and lock they using
the 3.9x9.5mm phillips

Æ

tapping screws (25).

HI-QUALITY ANTENNAS MADE IN ITALY

26

27

Finally mount the
antenna on the mast
using M6 washer (7), M6
spring lock washer (8),
M6 hexagonal nut (9),
steel bracket (26 & 27)
and M6x240mm U-bolt
(28).

28

HI-QUALITY ANTENNAS MADE IN ITALY

ID041, pag.1/4

TUNING TABLETUNING TABLE

MOUNTING INSTRUCTIONSMOUNTING INSTRUCTIONS

Freq.

(MHz)

Ch.19 CB 27.185

27.5

28.0

10m band 28.5

L1

(mm)

930
890
870
840

L2*

(mm)

¸

630 640

¸

620 630
623 633

¸

618 628

¸

L3

(mm)

730
640
440
300

* For the best tuning, please adjust only the gamma match L2 with an

SWR-Meter, about indicated range.

REMARK: use a good coax cable like RG-8 or RG-213 as short as possible
to get the best performance and we recommend to mount your antenna as

far as possible from metall roofs, walls, power lines and other antennas.

Mounting needed tools:

n. 1 tape rules (meter)
n. 1 screwdriver cross point
n. 1 10mm open key
n. 2 8mm open key

Pos

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

Description

Q.ty

aluminium bracket

1

1

1

2

3

4

5

6

7

8

9

Æ 33.5x37x1400mm alu. tube with connector first section

6

M5x16 hexagon head screws

6

M5 washer

6

M5 hexagonal nuts
gamma match assembly

1

M6 washer

11

M6 spring lock washer

11

M6 hexagonal nuts

7

Æ 30.5x33x1400mm alu. tube second section

1

1

Æ 36-39mm hose clamp

1

Plastic fixing ring

4

Plastic arms

8

Æ 3.9x12.7 tapping screws

1

M6x10 hexagon socket set screw

1

3mm hexagonal key

4

Æ 11x13x1400mm alu. tube (cone bottom side)

4

M6x12 hexagon head screws

4

Æ 8x10x1400mm alu. tube (cone top side)

4

aluminium ring section

1

top section with cage

1

M4x4 hexagon socket set screw cup point

1

2mm hexagonal key

1

5 sections telescopic aluminium whip

10

Æ 3.9x9.5 tapping screws

3

30x65mm steel “V” bracket

3

30x65mm steel “flat” bracket

3

M6x240mm U-bolt

Parts List

4

5

L1

3

Mount the aluminium
bracket (1) at distance L1

1

2

from the top edge of
bottom aluminium ring
(see tuning table for
frequency). Verify the real
alignement to the bracket
(1) and the connector (2).
Lock the bracket using

to align

M5x16

screws

(4) and M5 hexagonal nut
(5).

1

Pull out the aluminium
bar of gamma match at

4

3

5

distance L2 from the
plastic cap (see tuning
table for frequency) and

L2

lock it with the aluminium
bracket (1) using M5x16
hexagon head screw (3),
M5 washer (4) and M5
hexagonal nut (5).

13

12

Mount the plastic ring (12) on the
second aluminium tube (10) at
1340 mm from the bottom
aluminium ring. Insert the plastic
arms (13) and lock them using
the 3.9x12.7mm phillips

Æ

tapping screws (14). Lock the
plastic ring (12) using the M6x10
hexagon socket set screw cup
point (15) and 3mm hexagonal
key (16). Verify that the plastic
arms (13) are aligned with
bottom hole on aluminium ring.

14

11

hexagon head

(3), M5 washer

33

55

15

16

10

1340mm

to align

6

Mount the gamma match
(6) on the connector and
lock it using M6 washer (7),
M6 spring lock washer (8)
and M6 hexagonal nut (9).

22

9

8

7

10

44

Insert the second section
on the aluminium tube (10)
into the first section tube
(2) and lock them using the
enclosed hose clamp (11).

11

Insert limit punching

2

66

Mount the cone made of
aluminium tubes

Æ

13x1400 (17) on the
bottom aluminium ring
using M6x12 hexagon
head screws (18), M6
washer (7) and M6 spring
lock washers (8).

17 x 4 pcs

7

8

18

HI-QUALITY ANTENNAS MADE IN ITALY

ID041, pag.2/4

HI-QUALITY ANTENNAS MADE IN ITALY

ID041, pag.3/4