Siqura XSNet 4000 SW Quick Start Manual

Industrial Ethernet Switch

Quick Start Guide

This quick start guide describes how to install and use the
Industrial Ethernet Switch. Capable of operating at
temperature extremes of -10°C to +60°C, this is the Switch of
choice for harsh environments constrained by space.

Physical Description

The Terminal Block and Power input

The Terminal Block

PWR Power Input
GND Power Ground

Earth Ground

DC Terminal Block Power Input: The DC Terminal Block
power input can be used to power up this Switch.

The 10/100Base-TX and 100Base-FX/BX Connectors

1. The 10/100Base-TX Connections

The following lists the pinouts of 10/100Base-TX ports.

1

Industrial Ethernet Switch

Pin Regular Ports Uplink Port

1 Output Transmit Data + Input Receive Data +

2 Output Transmit Data - Input Receive Data -

3 Input Receive Data + Output Transmit Data +

4 NC NC

5 NC NC

6 Input Receive Data - Output Transmit Data -

7 NC NC

8 NC NC

2. The 100Base-FX Connections

The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx

(receive) port of device I to the Tx (transmit) port of device II.

3. The WDM 100Base-BX Connections

The fiber port pinouts: Only one Single mode or Multi mode

optical fiber is required to transmit and receive data.

2

Industrial Ethernet Switch

The Port Status LEDs

LED State Indication

10/100TX or 100FX/BX

Steady

A valid network connection established.
LINK stands for LINK.

LINK/ACT

Flashing

Transmitting or receiving data.
ACT stands for ACTIVITY.

Steady The port is transferring at 100Mbps.

100

Off

The port is transferring at 10Mbps If this
LED is dark.

3

Industrial Ethernet Switch

4

Functional Description

y Complies with EN61000-6-2 & EN61000-6-3 EMC

Generic standard immunity for industrial environment.

y Supports 802.3/802.3u/802.3x. Auto-negotiation:

10/100Mbps, Full/Half-duplex. Auto MDI/MDIX.

y 100Base-FX: Multi mode/Single mode SC or ST type.

100Base-BX: WDM Multi mode/Single mode SC type.

y Supports 2048 MAC addresses, 384K bits buffer

memory.

y Store-and-forward mechanism.
y Full wire-speed forwarding rate and non-blocking

mechanism.

y Broadcast storm filtering.
y Operating voltage and Max. current consumption: 0.2A

@ 12VDC, 0.1A @ 24VDC, 0.05A @ 48VDC. Power
consumption: 2.4W Max.

y Power Supply: DC Terminal Block power input,

12-48VDC.

y Operating temperature ranges from -10°C to 60°C.
y Compact DIN-Rail industrial case design.

Assembly, Startup, and Dismantling

y Assembly: Place the Switch on the DIN rail from above

using the slot. Push the front of the Switch toward the
mounting surface until it audibly snaps into place.

y Startup: Connect the supply voltage to start up the

Switch via the terminal block.

y Dismantling: Pull out the lower edge and then remove

the Switch from the DIN rail.

Industrial Ethernet Switch

5

Industrial Ethernet Switch

6

Preface

A member of the growing family of rugged switches, this
switch addresses a need for a smaller switch. This switch
provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial
floor shop, multitenant dwellings or Fiber To The Home
(FTTH) applications. Capable of operating at temperature
extremes of -10°C to +60°C, this is the switch of choice for
harsh environments constrained by space.

Plug-and-Play Solution:
The switch is a plug-and-play Fast Ethernet Switch in
compact size. It doesn't have any complicated software to
set up.

This manual describes how to install and use the hardened
compact Ethernet Switch. This switch integrates full wire
speed switching technology. This switch brings the answer
to complicated hardened networking environments.

To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.

In this manual, you will find:

y Features on the switch
y Illustrative LED functions
y Installation instructions
y Specifications