Siqura HSD622, HSD626 Installation Manual
Siqura HSD622/626
IP PTZ Camera with Day/Night, WDR, SFP Option
Installation Manual
Note: To ensure proper operation, please read this manual thoroughly before using the
product and retain the information for future reference.
Copyright © 2015 Siqura B.V.
All rights reserved.
HSD622/626
Installation Manual v3 (111502-3)
AIT55
Nothing from this publication may be copied, translated, reproduced, and/or published by
means of printing, photocopying, or by any other means without the prior written permission
of Siqura.
Siqura reserves the right to modify specifications stated in this manual.
Brand names
Any brand names mentioned in this manual are registered trademarks of their respective
owners.
Liability
Siqura accepts no liability for claims from third parties arising from improper use other than
that stated in this manual.
Although considerable care has been taken to ensure a correct and suitably comprehensive
description of all relevant product components, this manual may nonetheless contain errors
and inaccuracies. We invite you to offer your suggestions and comments by email via
t.writing@tkhsecurity.com. Your feedback will help us to further improve our documentation.
How to contact us
If you have any comments or queries concerning any aspect related to the product, do not
hesitate to contact:
Siqura B.V.
Zuidelijk Halfrond 4
2801 DD Gouda
The Netherlands
General : +31 182 592 333
Fax : +31 182 592 123
E-mail : sales.nl@tkhsecurity.com
WWW : www.siqura.com
2
Contents
1 Introduction .............................................................................................. 4
2 Safety ....................................................................................................... 6
2.1 Safety Information ............................................................................... 6
2.2 Cautions ............................................................................................. 7
2.3 Regulations ......................................................................................... 9
3 Product Description ................................................................................... 10
3.1 Product Overview ................................................................................ 10
3.2 General Operation Requirements ........................................................... 11
3.3 Package Contents ................................................................................ 11
4 Dome Setup and Cable Connection ............................................................ 13
4.1 Prepare the HSD622/626 for installation ................................................. 13
4.2 Switch definition .................................................................................. 13
4.3 Communication switch configuration ...................................................... 14
4.4 Establishing a Network Connection ......................................................... 15
4.5 System compatibility ............................................................................ 16
4.6 RJ-45 to SFP Changeover ...................................................................... 16
4.7 Dome cable definition and requirements ................................................. 19
4.7.1 Cable requirements .......................................................................... 19
4.7.2 Verifying Ethernet connectivity .......................................................... 19
4.7.3 22-pin cable harness ........................................................................ 19
4.7.4 22-pin connector definition ................................................................ 20
5 Dome Installation ..................................................................................... 21
5.1 Dome Dimensions ................................................................................ 21
5.2 Installation Scenarios ........................................................................... 22
5.3 Ceiling Mount ...................................................................................... 22
5.3.1 Ceiling mounting with a straight tube ................................................. 22
5.4 Wall mount ......................................................................................... 23
5.4.1 Mini wall mount ............................................................................... 24
5.4.2 Wall mounting with gooseneck tube ................................................... 25
5.4.3 Wall box mounting ........................................................................... 26
5.5 Corner mount ...................................................................................... 27
5.6 Pole mount ......................................................................................... 29
5.6.1 Pole thin/wide direct mounting .......................................................... 29
5.6.2 Pole thin/wide box mounting ............................................................. 30
6 System Integration ................................................................................... 32
Appendix A: Camera Accessories ............................................................... 33
Mounting Accessories ........................................................................... 33
HSD622/626 Accessories ...................................................................... 38
Index ...................................................................................................... 39
3
1 Introduction
Document scope
This manual applies to Siqura's outdoor high-speed IP PTZ dome cameras, the HSD622/626.
It describes how to install and connect the HSD622/626 cameras. Operation and configuration
of the HSD622/626 cameras is covered in the user manual.
Intended audience
This manual is aimed at installers and technicians involved in the installation of network
devices, such as the HSD622/626.
Assumed skills and know-how
To work with the HSD622/626 camera, an installer or technician must have adequate
knowledge and skills in the fields of:
● CCTV systems and components
● Electrical wiring and low-voltage electrical connections
● Ethernet network technologies and Internet Protocol (IP)
● Windows environments
● Web browsers
● Video, audio, data, and contact closure transmissions
● Video compression methods
Specifications
The information given in this manual was current when published. Siqura reserves the right to
revise and improve its products. All specifications are subject to change without notice.
Important Information
Before proceeding, please read and observe all instructions and warnings in this manual.
Retain this manual with the original bill of sale for future reference and, if necessary, warranty
service. When unpacking your product, check for missing or damaged items. If any item is
missing, or if damage is evident, do not install or operate this product. Contact your supplier
for assistance.
4
Introduction
Typographical Conventions
Before you start using this guide, it is important to understand the typographical conventions
used in the documentation. The following kinds of formatting in the text identify special
information.
Formatting convention Type of Information
Numbered list Step-by-step procedures. You can follow these
instructions to complete a specific task.
Special Bold Items you must select, such as menu options, command
buttons, or items in a list.
Emphasis Used to emphasize the importance of a point or for
variable expressions such as parameters.
CAPITALS Names of keys on the keyboard. for example, SHIFT,
CTRL, or ALT.
KEY+KEY Key combinations for which the user must press and hold
down one key and then press another, for example, CTRL
+P, or ALT+F4.
5
2 Safety
This chapter contains the HSD622/626 safety instructions.
In This Chapter
2.1 Safety Information..................................................................................................6
2.2 Cautions................................................................................................................7
2.3 Regulations............................................................................................................9
2.1 Safety Information
General
The safety information contained in this section, and on other pages of this manual, must be
observed whenever this unit is operated, serviced, or repaired. Failure to comply with any
precaution, warning, or instruction noted in the manual is in violation of the standards of
design, manufacture, and intended use of the module. Siqura assumes no liability for the
customer's failure to comply with any of these safety requirements.
Trained Personnel
Installation, adjustment, maintenance, and repair of this equipment are to be performed by
trained personnel aware of the hazards involved. For correct and safe use of the equipment
and in order to keep the equipment in a safe condition, it is essential that both operating and
servicing personnel follow standard safety procedures in addition to the safety precautions
and warnings specified in this manual, and that this unit be installed in locations accessible to
trained service personnel only.
Safety Requirements
The equipment described in this manual has been designed and tested according to the
UL/IEC/EN 60950-1 safety requirements.
Warning: If there is any doubt regarding the safety of the equipment, do not put it into
operation.
This might be the case when the equipment shows physical damage or is stressed beyond
tolerable limits (for example, during storage and transportation).
Important: Before opening the equipment, disconnect it from all power sources.
The equipment must be powered by a SELV1 power supply. This is equivalent to a Limited
Power source (LPS, see UL/IEC/EN 60950-1 clause 2.5) or a "NEC Class 2" power supply.
When this module is operated in extremely elevated temperature conditions, it is possible for
internal and external metal surfaces to become extremely hot.
1. SELV: conforming to IEC 60950-1, <60 Vdc output, output voltage galvanically isolated
from mains. All power supplies or power supply cabinets available from Siqura comply with
these SELV requirements.
6
Safety
Optical Safety (HSD622/626 /SFP)
This optical equipment contains Class 1M lasers or LEDs and has been designed and tested to
meet IEC 60825-1:1993+A1+A2 and IEC 60825-2:2004 safety class 1M requirements.
Warning: Optical equipment presents potential hazards to testing and servicing personnel,
owing to high levels of optical radiation.
When using magnifying optical instruments, avoid looking directly into the output of an
operating transmitter or into the end of a fiber connected to an operating transmitter, or there
will be a risk of permanent eye damage. Precautions should be taken to prevent exposure to
optical radiation when the unit is removed from its enclosure or when the fiber is disconnected
from the unit. The optical radiation is invisible to the eye.
Use of controls or adjustments or procedures other than those specified herein may result in
hazardous radiation exposure.
The installer is responsible for ensuring that the label depicted below (background: yellow;
border and text: black) is present in the restricted locations where this equipment is installed.
EMC
The equipment has been tested and found to meet the CE-regulations relating to EMC, and
complies with the limits for a Class B device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against interference to radio communications in
any installation. The equipment generates, uses, and can radiate radio frequency energy;
improper use or special circumstances may cause interference to other equipment or a
performance decrease due to interference radiated by other equipment. In such cases, the
user will have to take appropriate measures to reduce such interactions between this and
other equipment.
Any interruption of the shielding inside or outside the equipment could make the equipment
more prone to fail EMC requirements.
Non-video signal lines must use appropriate shielded Cat 5 cabling (S-FTP), or at least an
equivalent. Ensure that all electrically connected components are carefully earthed and
protected against surges (high voltage transients caused by switching or lightning).
ESD
Electrostatic discharge (ESD) can damage or destroy electronic components. Proper
precautions should be taken against ESD when opening the equipment.
2.2 Cautions
Handle the camera carefully.
Do not abuse the camera. Avoid striking, shaking, etc. as the camera can be damaged by
improper handling or storage.
7
Safety
Install electrical wiring carefully.
Ask a qualified electrician to perform the wiring for the installation. Please note that input
electricity to the unit is at a tolerance of 24VAC 50/60 Hz ± 10%. Ground the camera
appropriately to prevent electric shock or damage.
Cable harness Power input: 3-pin terminal block
To prevent electric shock, do not remove screws or covers. There are no user serviceable
parts inside. Please consult technical support if a camera is suspected of malfunctioning.
Do not operate the camera beyond the specified temperature,
humidity, and power source ratings
Use the indoor camera under conditions where the temperature is between 0°C~40°C
(32°F~104°F).
Do not block the cooling vent on indoor cameras.
This camera has a cooling fan inside. Blocking the cooling holes may lead to overheating and
cause malfunction. Overheating is not covered by warranty.
Do not expose the indoor dome camera to moisture or operate it
in wet areas.
The indoor dome camera is designed for indoor use or use in locations where it is protected
from rain and moisture. If the indoor camera gets wet, turn the power off immediately and
ask a qualified technician for servicing. Moisture can damage the indoor camera and also
create the danger of electric shock.
Do not use strong or abrasive detergents when cleaning the
camera.
Use a dry cloth to clean the camera when it is dirty. If the dirt is hard to remove, use a mild
detergent and wipe gently. To clean the lens, use lens tissue or a cotton tipped applicator and
ethanol. DO NOT clean the lens with strong detergents.
Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at
the sun or other extremely bright objects, as this can damage the camera.
8
Safety
2.3 Regulations
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions.
● This device may not cause harmful interference.
● This device must accept any interference received, including
interference that may cause undesired operation.
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste in accordance with
Directive 2002/96/EC. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment. By proper waste handling of this product you
ensure that it has no negative consequences for the environment
and human health, which could otherwise be caused if this product is
thrown into the garbage bin. The recycling of materials will help to
conserve natural resources.
For more information on how to recycle this product, please contact
your local city office, your household waste disposal service or the
seller of the product.
Compliance is evidenced by written declaration from our suppliers,
assuring that any potential trace contamination levels of restricted
substances are below the maximum level set by EU Directive
2002/95/EC, or are exempted due to their application.
9
3 Product Description
The HSD622/626 high-speed PTZ dome camera is designed to deliver superb performance and
durability with an intelligent and stylish housing suitable in any security and surveillance
installation.
This manual focuses on the outdoor models in the HSD622/626 series, the HSD622 and
HSD626 cameras.
In This Chapter
3.1 Product Overview..................................................................................................10
3.2 General Operation Requirements.............................................................................11
3.3 Package Contents................................................................................................. 11
3.1 Product Overview
Siqura HSD 622 Features
● Outdoor High Speed Network PTZ dome
● Quad stream support: Dual H.264, MPEG-2, MPEG-4 and MJPEG
● 26x Optical Zoom/12x digital zoom
● Day/Night with IR-cut filter
● Back Light Compensation
● Wide Dynamic Range
● 400°/second preset targeting
● 360° endless panning
● 256 presets/8 programmable cruises
● 8 alarm in/1 output
● Two-way audio
● 24 Privacy Masks
● Analog Output
● Optical output option
Siqura HSD 626 Features
● Quad stream support Dual H.264, MPEG-2, MPEG-4 and MJPEG
● 35x Optical Zoom/12x digital zoom
● Day/Night with IR-cut filter
● Wide Dynamic Range
● Back Light Compensation
● Electronic Image Stabilization
● 400°/second Preset targeting
● 360° endless panning
● 256 presets/8 programmable cruises
● 8 alarm in/1 output
● Two-way audio
● 8 Privacy Masks
10
Product Description
● Analog Output
● Optical output option
3.2 General Operation Requirements
A minimum of one control device is required for operation, such as a control keyboard, a DVR,
or a PC. The HSD622/626 cameras contain a built-in receiver that decodes commands
originating from a control device.
The built-in Pelco D protocol provides connectivity to other surveillance systems and allows
the HSD622/626 to be integrated with other suppliers' surveillance systems.
3.3 Package Contents
Before proceeding, please verify that the box contains the items listed here. If any item is
missing or has defects, do not install or operate the product. Contact your supplier for
assistance.
11
Product Description
HSD622/626
Dome Body Optical cover CD: Operation and Installation
M3 standard screw (x1)
M3 security screw (x1)
M5 standard screw (x1)
M5 security screw (x1)
Lubricant Waterproof Boot
Manuals
1,
Security TORX 30 cm cable harness for power supply, video, and RS-485
SFP end cap accessory Quick start guide
12
Loading...