Sioux Tools 5557 User Manual

Model

5557

Form

Date

#

Z544

4-99/A

ggB

8"

Geared

.

Read

these instructions

tool. Keep

SAFETY

Use - Safety Glasses

Use

-

Safety

Use

-

Safety

Use - Breathing
Use

-

Ear

-

Do not use as a grinder.

-

Do not use polystyrene pads.

-

Use accessories rated above

-

Prolonged exposure to vibration may cause Injury.

-

Read all instructions before using this tool.
be fully

-

DO not exceed the maximum working air pressure.

-

Use personal protection equipment

-

Use compressed air only
conditions.

-

If the tool appears to malfunction, remove from
immediately and arrange for service and repair. If
practical to remove tool from service, then shut off the air
supply to the tool and write or have written a warning
note and attach it to the tool.

-

If tool

is

device, ensure that the tool is firmly attached to the
suspension/support device.

-

When operating the tool, always keep the body and
particularly the hands away from the working attachment
fixed to the tool.

-

The tool is not electrically insulated. Never use the tool if
there is any chance
electricity.

-

Always when using the toot, adopt a firm footing and/or
position and grip the tool sufficiently only to overcome
any reaction forces that
work. Do not overgrip.

-

Use only correct spare parts for maintenance and repair.
Do not improvise or make temporary repairs. Major
servicing and repairs should only be
carried out

-

Do

not

valve in 'On' position. The throttle
trigger1 lever, etc. must always be free
to return to the 'Off' position
released.

-

Always shut
and press the 'On/Off'valve to exhaust
the air from
fitting, removing or adjusting the
working attachment fitted to the tool.

-

Before using the tool, make sure that a
shut off device has been fitted to
supply line and the position

these

instructions in a

MESSAGES

Personal

Safety

Gloves
Boots

Masks

Protectors

Wried

in

its

use and aware of these safety rules.

to be used with a balancer of other suspension

of

may

bv

cersons trained to do so.

lock, tape, wire, etc. the'On1Off1

off

the airsupply to the tool

the

feed hose before

carefully

1

A

Equipment

YES

1

0

@

@

YES

Safety

850

at

the recommended

coming into contact with live

result from the tool doing

Ah

-

rules

RPM.

AH

operators must

as

recommended.

7-

Should

is

known

when

the

To

Recommended

Dual

Action

Sander

IMPORTANT

before installing, operating, servicing or repairing
safe

accessible

WARNING

Always Read Instructions Before
Using Power Tools

Always Wear Safety Goggles
Wear Hearing Protection

Avoid Prolonged Exposure

T

o Vibration

-

when

it

All

with

Maintain

Working

use

is

not

Pipe

And

Be

112'

Sufficient

Recommended

Pressure

Each

Tool

Page

using

Fittings

Of

Capacity

Oullel

place.

1

Operator Instructions

Foreseen
Work

Putting

Use

Stations

Into

Service

Operating
Dismantling

a

5557

and easily accessible so that the air supply to the tool can

be shut off in an emergency.

-

Check hose and fittings regularly for wear.

-

Take care against entanglement of the moving parts of
the tool with clothing, hair, ties, cleaning rags, rings,
jewelry, watches, bracelets, etc.This could cause the body
or parts of the body to be drawn towards and in contact
with the moving parts of the tool and could be very
dangerous.

-

It is expected that users will adopt safe working practices
and observe all local, regional
when installing, using or maintaining the tool.

-

Take care that the exhaust air does not point towards any
other person or material or substance that could be
contaminated by oil droplets. When first lubricating a tool
or

if

the

the exhaust air to come near very hot surfaces or flames.

-

Never lay the tool down until the working attachment has
stopped moving.

-

When the tool is not in use, shut off the air supply and
press throttle trigger/lever to drain the supply line. If
tool is not to be used for a period of time. first lubricate,
disconnect from air supply and store in
temperature environment.

-

If

the tool is passed from one user to a new or inexperi-

enced user, make sure these instructions are available to

be

passed with the tool.

-

Do not remove any manufacturer fitted safety devices

where fitted, i.e., wheel guards, safety trigger, speed
governors, etc.

Large

At

Air

Supply System

NO

1

Sander

or

tool exhaust has a high oil content, do not allow

Take

Alf

From

Easy

To

Reach

Shut

Off

And

Valve

Operala

and

country legal requirements

a

dry average room

Top

Air

Tool

Assembly.

this

Figure

the

1