Sioux Tools 5265 User Manual
Form
#
Date
Model
5"
Dia. Angle Sander
5265
2-02lA
IMPORTANT
Read these instructions carefully before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe accessible place.
Z409
A
SAFETY MESSAGES
Personal Safety Equipment
Use - Safety Glasses
Use - Safety Gloves
Use - Safety Boots
Use
-
Breathing Masks
Use - Ear Protectors
YES
YES
YES
YES
WARNING
Always Read Instructions Before
0
Using Power Tools
@
Always Wear Safety Goggles
@
Wear Hearing Protection
Avoid Prolonged Exposure
W^
TO Vibration
Safety rules when using a
-
Do not use as a grinder.
-
Do not use polystyrene pads.
-
Use accessories rated above
-
Prolonged exposure to vibration may cause injury.
-
Read all instructions before using this
be fully trained
-
Do not exceed the maximum working air pressure.
-
Use personal protection equipment
-
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects and other
reproductive harm.
-
Use compressed air only at the recommended conditions.
-
If the tool appears to malfunction, remove from use
immediately and arrange for service and repair. If it is not
practical to remove tool from service, then shut off the air
supply to the tool and write or have written a warning
note and attach it to the tool.
-
If tool is to be used with a balancer or other suspension
device, ensure that the tool is firmly attached to the
suspension/support device.
-
When operating the tool, always keep the body and
particularly the hands away from the working attachment
fixed to the tool.
-
The tool is not electrically insulated. Never use the tool if
there is any chance of coming into contact with live
electricity.
-
Always when using the tool, adopt a firm footing andlor
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-
Use only correct spare parts for maintenance and repair. Do not improvise
or make temporary repairs. Major
servicing and repairs should only be
carried out by persons trained to do so.
-
Do not lock, tape, wire, etc. the'On/Off'
valve in 'On' position. The throttle
trigger/ lever, etc. must always be free
to return to the 'Off' position when
released.
-
Always shut off the air supply to the tool
and press the 'On/Offl valve to exhaust
the air from the feed hose before
fitting, removing or adjusting the
in
its
use
7,000
RPM.
tool.
All
and
aware of these safety rules.
operators
as
recommended.
7
with
To Maintain Recommended
Working Pressure At
\
Recommended Air Supply System Figure
must
Sufficient Capacity
Each Tool Outlet
Page No
Operator Instructions
Includes:
Safetv Rules
ores seen
Work Stations
Putting Into Service
Operating
Dismantling and Assembly.
5265
working attachment fitted to the tool.
-
Before using the tool, make sure that a shut off device
has been fitted to the supply line and the position is known
and easily accessible so that the air supply to the tool can
be shut off in an emergency.
-
Check hose and fittings regularly for wear.
-
Take care against entanglement of the moving parts of
the tool with clothing, hair, ties, cleaning rags, rings,
jewelry, watches, bracelets,
or parts of the body to be drawn towards and in contact
with the moving parts of the tool and could be very
dangerous.
-
It is expected that users will adopt safe working practices
and observe
when installing, using or maintaining the tool.
-
Take care that the exhaust air does not point towards any
other person or material or substance that could be
contaminated by oil droplets. When first lubricating a tool
or if the tool exhaust has a high oil content, do not allow
the exhaust air to come near very hot surfaces or flames.
-
Never lay the tool down until the working attachment has
stopped moving.
-
When the tool is not in use, shut off the air supply and
press throttle triggerllever to drain the supply line. If the
tool is not to be used for a period of time, first lubricate,
disconnect from air supply and store in a dry average room
temperature environment.
-
If the tool is passed from one user to a new or inexperienced user, make sure these instructions are available to
be passed with the tool.
Sander
all
local, regional or country legal requirements
Take Air From Top
Use
etc.This could cause the body
-
Low Spot To
Trap Water
11
11
11
11
Easy
Operate. Shut Oft Valve
To Reach
And
Air Tool
11
Drain Daily
L
Filter Lubricator
1
a
1
Loading...