Sioux Tools 5093L, 5093 User Manual
Model
1
5093 & 5093L
"
Super Duty
"D"
Form
#
Z541
Date 2-02/A
Handle Impact Tools
bl
c?
IMPORTANT
Read these instructions carefully before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe accessible place.
I
I
SAFETY MESSAGES
Personal
Safety
Use - Safety Glasses
Use - Safety Gloves
Use
-
Safety Boots
Use
-
Breathing Masks
Use
-
Ear Protectors
-
Equipment
--
YES
YES
--
--
A
WARNING
Always Read Instructions Before
@
Using Power Tools
@
Always Wear Safety Goggles
@
Wear Hearing Protection
Avoid Prolonged Exposure
ti23
T
Safety rules when using a
-
Use only impact sockets and extensions, universal joints,
etc., rated as beino suitable for use with impact tools.
-
Prolonged exposure to vibration may cause injury.
-
Read all instructions before usina this tool. All ooerators
be fully trained in
-
Do not exceed the maximum working air pressure.
-
Use personal protection equipment as recommended.Some dust created
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects and other
reproductive harm.
-
Use compressed air
-
If the tool appears to malfunction, remove from use
immediately and arrange for service and repair. If it is not
practical to remove tool from service, then shut off the air
supply to the tool and write or have written a warning
note and attach it to the tool.
-
If tool is to be used with a balancer or other suspension
device, ensure that the tool is firmly attached to the
suspensionlsupport device.
-
When operating the tool, always keep the body and
particularly the hands away from the working attachment
fixed to the tool.
-
The tool is not electrically insulated. Never use the tool if
there is any chance of coming into contact with live
electricity.
-
Always when using the tool, adopt a firm footing and/or
position and rip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-
Use only correct spare parts for maintenance and repair.
Do not improvise or make temporary repairs. Major
servicing and repairs should only be carried out by
persons trained to do so.
-
Do not lock, tape, wire, etc. the 'OnIOff' valve in 'On'
position.The throttle triggernever, etc. must always be free
to return to the 'Off' position when released.
-
Always shut off the air supply to the tool and press the
'On/Off' valve to exhaust the air from
the feed hose before fitting, removing
or adjusting the working attachment
fitted to the tool.
-
Before using the tool, make sure that a
shut off device has been fitted to the
supply line and the osition is known
and easily accessible so that the air
supply to the tool can be shut off in an
emergency.
-
Check hose and fittings regularly for wear.
-
Take care against entanglement of the
movina
Darts
ties, cleaning rags, rings, jewelry, watches;
bracelets, etc. This
or
parts
and in contact with the moving
tool and could
its
use
and
by
power sanding, sawing, grinding,
only
at
the
of the tool with dothina. hair.
could
of the
body
be
cause the body
to be drawn towards
very dangerous.
a&
of
these
safety
recommended conditions.
7
parts
of the
Recommended Air Supply System
rules.
o Vibration
must
Page No
509315093L
-
It is expected that users will adopt safe working practices
and observe all local, regional or country legal
requirements when installing, using or maintaining the tool.
-
Take care that the exhaust air does not point towards any
other person or material or substance that could be
contaminated by oil droplets. When first lubricating a tool
or if the tool exhaust has a high oil content, do not allow
the exhaust air to come near very hot surfaces or flames.
-
Never lay the tool down until the working attachment has
stopped moving.
-
When the tool is not in use, shut off the air supply and
press throttle triggerllever to drain the supply line. If the
tool is not to be used for a period of time, first lubricate,
disconnect from air supply and store in a dry average room
temperature environment.
-
If the tool is passed from one user to a new or inexperienced user, make sure these instructions are available to
be passed with the tool.
-
Do not remove any manufacturer fitted safety devices
where fitted, i.e., wheel guards, safety trigger, speed
governors, etc.
-
Wherever ossible, secure workpiece with clamps, a vise,
etc. to make it rigid so it does not move during the work
operation. Keep good balance at all times. Do not stretch
or overreach.
-
Try to match the tool to the work operation. Do not use a
tool that is too light or heavy for the work operation. If in
doubt, seek advice.
-
In general terms, this tool is not suitable for underwater
use or use in explosive environments
manufacturer.
-
Try to make sure that the work area is clear to enable the
work task to be performed safely. If practical and
possible, try to clear unnecessary obstructions before
starting work.
-
Always use air hose and couplings with minimum work-
ing pressure ratings at least
working pressure rating of the tool.
Easy
Operate
1
Operator Instructions
Includes:
Safety Rules
Foreseen Use
Work
Stations
Putting Into Service
Operating
Dismantling and Assembly.
Impact
Tool
-
1
112
times the maximum
Air
To
Reach And
Shut
Off
Valve
Tool
seek advice from
Figure
1
1
Loading...