SINUS Powerline 18 Q4W RGBW User Instructions

Powerline 18 Q4W RGBW

User Instruction

Thank you for purchasing this product. For your own safety, please read this user manual carefully
before you initially start-up

SAFETY INSTRUCTIONS

◆ Every person involved with the installation, operation and maintenance of this device has to :

- be qualified

- follow the instructions of this manual

◆ CAUTION! Be careful with your operations. With a dangerous voltage you can suffer a dangerous

electric shock when touching the wires!

◆ This device has left our premises in absolutely perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.

◆ Important: Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.

◆ Keep away from heaters and other heating sources!

◆ If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch

it on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.

◆ Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.

◆ If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the

manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

◆ Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an
extent that their effectiveness is impaired, for example by cracks or deep scratches.

◆ Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution!

◆ Make sure that the available voltage is not higher than stated in this manual.

◆ Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the

power-cord by the plug. Never pull out the plug by tugging the power-cord

◆ During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.

◆ DANGER OF BURNING! Never touch the device during the operation! The housing heats up to the
housing temperature TSURFACE.

◆ Don't switch the device on and off in short intervals as this would reduce the lamp's life

◆ HEAL TH HAZARD! Never look directly into the light source, as sensitive persons may suffer an

epileptic shock (especially meant for epileptics)!

◆ Always disconnect from the mains, when the device is not in use or before cleaning it

◆ Please note that damages caused by manual modifications on the device or unauthorized operation by

unqualified persons are not subject to warranty.

◆ Keep away children and amateurs from the device!

◆ There are no serviceable parts inside the device. Maintenance and service operations are only to be

carried out by authorized dealers

Function test

(1)

This system has DMX Online mode and Stand-alone Mode. Online mode can link other
units and be controlled by the DMX controller. And Stand-alone Mode has the functions of
Sound, Auto Mixcolor and Strobe and so on.

（2） If the slave links up master and also connects DMX contrloller, the master can identify automatically
and turn off the function of sending data from master, the slave receives signals from DMX controller

（3） When there is no DMX signals to connect under DMX mode, the menu will show “HIGHLITE NO DMX
SIGNAL!”，while there is DMX signals to connect,the menu will back to the original state.

(4）The unit has the function of automatically saving present state,and under power off it will run the last

mode when re-turn on.

Function descrition

Display:

LCD
1 MODE ：select LED mode,detail see figure 1
2 UP ：select DMX address,program speed and dimmer value clockwise direction
3 DOWM ：select DMX address,program speed and dimmer value counter-clockwise direction

LCD display and function description

Mode LCD display Operation

displa
y
mode

Turn on
display
On all the
time
Auto turn off 1 DispPerm

HIGHLITE
SoftWare V 1.0
1 DispPerm
BackLight on

BackLight off

When turn on it will show HIGHLITE SoftWare V 1.0

LCD is on all the time

LCD will turn off automatically after running 10s,under this
position,any key has no function.it can turn on by pressing any key
for 3s.