Singer 253-201 User Manual

Form
(156)
Printed
20810
in U S. A.
LIST
OF
PARTS
MACHINE
SINGER
No.
253-20I
I
THE
SINGER
**A
Trode
MorkofTHE
SINGER
MANUFACTURING
MANUFACTURING
COMPANY
COMPANY
INSTRUCTIONS
FOR
OILING
Before
the
basetothe
OIL,
structed
"TYPE C" OIL Is to
which will produce a minimum of stain on fabrics, after
starting
the
machine,
HIGH MARK
fill
with
the
oil
"TYPEA"or
reservoir
"TYPE
sold by Singer Sewing Machine Company, as in
in
Form
20482.
be
used,
when
an
oil is
desired
even
a long period of
storage.
The reservoir holds approximately 1Vapints.
When
should be inspectedatleast twice a month or as often
as
is necessary to keep it from going below
MARKinthe
or
"TYPE
in
operation,
the
reservoir. Refill to HIGH
C"
OIL.
oil level in
MARK
the
with
reservoir
the
LOW
"TYPE
A"
In
C"
Copyright©1956byThe
Singer
Manufacturing
Company
INDEX
Page
Accessories 17
Edge
Folders
Face
Plate
Fittings
Foot Liher Parts 25
HemmeronShank Knee
Lifter
Lap
Seam
Machine
Numerical
Tension Thread
on Shank 17
Thread
Lubricator 17
Parts
Fellers
No.
253-201
List of Parts 29
Releaser Unwinder
18
17 25
26
27
7
27
INSTRUCTIONS
FOR
ORDERING
In ordering from this list, use
the
FIRST
column.
ONLY
the
port
The number stamped on a Sewing Machine Part is in
every case the number of the single part only.
Every
combination of portssent out as such has its
number,
which,
although not stamped on the parts, must be
used when ordering the combination.
Each number always indicates the SAME
ever list it
of finish only, as follows:
The
appears,
letters
after
or for
some
whatever
of the
A—Hardened, Polished, Nickel Plated
A.A—Buffed
A.B—Hardened, Polished, Buffed
A.C—Brown
and
Chromium
Plated
Baking Enamel Finish
and
machine.
numbers
and
Chromium Plated
PARTinwhat
indicate
Buffed
A.D—Gray Baking Enamel Finish
A.E—Hardened, Bright Rumbled
A.F—Hardened,
A.G—Alumilite, Plain
A.H—Alumilite,
A.J—Polished, Nickel
A.K—Hardened, Polished, Nickel Plated
A.L—Heat
B—Polished, Nickel
Bright
Rumbled,
and
Chromium
Dyed
Plated
Treated for Toughness
Plated
Plated
and
and
and
Nickel Plated
Nickel
Chromium
Buffed
Plated,
and
Bright
Plated
Chromium Plated
C—HardenedOnly
C.R—Hardened
D—Polished
E—Soft,
F—Hardened
F.J—Hardened, Polished
G—BrightRumbled
H—Blued
J—Nickel
K—Hardened
L—Brass
M—Oxidized
and
Only
Not
Polished
and
Plated Only
and
Plated
Merlized
Polished
and
and
Nickel Plated
Nickel
Nickel
Plated
Plated
N—Japanned, Dull
P—Japanned, Bright
P.P—Wrinkle
R—Merlized
S—Cadmium
Finish
Plated
T—Copper Plated
T.A—Hardened,Polished, Copper and Nickel Plated
T.B—Copper
and
Nickel Plated
and
Polished
T.J—Copper and NickelPlated Only
T.K—Hardened,
T.L—Copper
T.M—CopperPlated
Copper and
and
Brass Plated
and
Nickel
Oxidized
Plated
NUMBER
specific
the
style
Rumbled
and
Buffed
in
INSTRUCTIONS
FOR
ORDERING-Continued
U—Zinc V—Silver
W—Polished
X—Black
X.C—Hardened
Y—Black
Z—Chromium
Z.A—Hardened, Polished, Nickel
Z.B—Polished, Nickel
Z.C—Hardened
Z,D—Polished
Z.G—Bright
ZJ—Nickel
Z.T—Copper
list;
Plated
Plated
Oxide,
Nickel Plated Only
Plated
and
Rumbled, Nickel Plated, Bright
Chromium
and
and
These letters
and
AFTER
In
this
series:
1 to
1500,
Screw
Numbers 1501to1800 1801to2000
2001
to
190000
are
are
numbers
and
Nickel
Plated
for Iron
and
Plated
Black
and
Oxide,
Steel
for Iron or
Plated,
Plated,
and
Chromium
Chromium
Plated
Chromium
Chromium
MUSTBEUSED
Buffed
Plated
Plated
Plated
Plated
and
Chromium
when they
the number as in the list.
50001 to
and and
50000
51500
51501to51800 51801to52000
and
52001
to
and
ore ore
140000
Sewing Machine Parts, 190001
of
Electrical
Parts.
Steel
Buffed
and
appear
140001 to
Nut
Roller
and
Rumbled
Numbers
and
The figures in the second column refer only to the plates,
illustrating the parts, and
Parts marked with an asterisk (*)
are
repairs
made at factory.
When ordering parts
distance between seams), the
are
NOT TOBEUSED
are
which
differ as to Gouge (the
Gauge,
furnished only when
as well as the Number,
must be given on order.
Chromium
Plated
and
in the
142000
Numbers
are
142001
upward
in ordering.
to
SINGER
These
Needles
in SINGER
Needles
are
marked
and
Company'sTrade Mark
should
Machines
be
their
Containers
with
the
"SI
MAN CO.**" i
used
NeedlesinContainers
"FOR
are
NOT
SINGER
SINGER
marked
MACHINES"
made needles. 2
LIST
OF
PARTS
COMPLETE
MACHINE
FOR
SEWING
TWO
LOOPERS,
MEDIUM
DROP
No.
WEIGHT
FEED.
ARMAT 11® ANGLE WITH BED.
INCHES. 1/32
SPEED
OPERATIONS
GAUGES
INCH.
5500
3/32
INCH TO
LENGTHOFSTITCHES
R.P.M.
DEPENDING
PERFORMED.
Arm
with
Due to the accuracy required for
be supplied separately and can only be sent out as a unit.
Arm
Trade
and
Bed
Arm Arm Arm Arm Arm
Arm Arm
Arm Shaft (horizontal) Flanged Bushing (back)
Arm Shaft (horizontal) Flanged Bushing (back) Set Screw....
Arm Shaft (horizontal) Flanged Bushing (back) Oil Sump
Arm Shaft (horizontal) Flanged Bushing (back) Oil Sump Arm Shaft (horizontal) Flanged Bushing (front)
Arm
Arm
Arm
assembled.
Dowel
Pin (2)
Screw
(front) (2)
Screw
Stud
Shaft
(horizontal)
Shaft
(horizontal)
Shaft
(horizontal) Bushing (center)
Shaft
(horizontal) Bushing (center) Set Screw
Tube
with
Holder
Tube
Holder
Shaft
(horizontal)
Shaft
(horizontal)
Shaft
(horizantal) Screw Plug (front)
253-201
FABRICS.
TWO-THREAD
NEEDLE
1/2
6 TO 22 TO
ON
MATERIAL USED
Name
Mork
end
(back)
(2) with 146651
Screw
Flanged
Screw
TWO
NEEDLES,
CHAIN
STITCH.
BAR
STROKE
1-3/16
INCH, IN
two
STEPS
OF
THE
INCH.
AND
Trade
Mark
gear
Needle
with
Bushing (front) Set Screw....
(back)
Rivets
alignment. Arm cannot
Bar
Crank
146581
PARTS
FOR
MACHINE
NO.
253-201
No.
143236
146661
1259AL 1259AL
146505
140298AL
147111
140298AL
146829
146830
146506
146507
146508
51369R
146509
146510
140676X
64519 146511 146513
143024
146514
965E
146877
146516 146650
1259AL
146518
50554AL
146519
50554AL
146520
448AL
64342
454AL
146521
4307
725X
146522
146006
146523
146834
146848
146849 146061
146687
146722 146820 146827 146007
146526
146835
Plate
25036 25036
25036 25036
25036
25036
25036
25036
25038
NOTE:
25039
25039 25039
25039
25039
25038
25039
25039
NOTE:
25036
25037 25037
25037 25040
25040
25040 25040
25040
25040 25040
25040
25040 25040 25041 25041 25041 25041
25042
25058
25055 25054 25067 25042
25042
25056
25061
ArmShaft (horizontal) Screw Plug (front) Washer (fiber)
ArmShaft (upright)
ArmShaft (upright) Bevel
ArmShaft (upright)
ArmShaft (upright) Bushing(lower)
ArmShaft (upright) Bushing(lower) Set Screw
ArmShaft (upright)
ArmShaft (upright)
ArmTop Cover
ArmTopCover 146829 with 140676X(for Agents only)
No. 146830 is used to prevent tampering withthe stitch set.
Arm Top Cover
Arm
TopCoverwith
Nos.
64519,146506,146509,146510
Arm Top Cover Arm Top Cover Screw (4)
ArmTop Cover Stitch Regulator Plunger
ArmTopCover Stitch Regulator Plunger Cap
ArmTop Cover Stitch Regulator Plunger Hole Plug Screw....
ArmTopCover StitchRegulator Plunger Spring ArmTopCover Stitch Regulator Plunger Stop
Bed
with
Due to the accuracy required for
be supplied separately and can only be sent out as a unit.
Arm
two
and
Bed
Bed Hole Plug Bed Leg (back)
Bed Leg (back) Screw (2) Bed Leg (front, long)
Bed Rotary Shaft
Bed Rotary Shaft 146516 with 146558
BedRotoryShaft BevelGear Set Screw(2)
Bed Rotary Shaft BedRotaryShaft
BedRotaryShaft
Bed Rotary Shaft Bushing(front) Set Screw Bed Rotary Shaft Bushing(intermediate)
Bed Rotary Shaft
Bed Rotary Shaft Collar with 454AL Bed Rotary Shaft Collar Set Screw
Bed
BedSlide (left) Spring BedSlide (left) Spring Screw (2)
BedSlide (left) complete, Nos. 4307,146521
BedSlide(right, button type) for 146007
Bed Slide (right, button type) for 146526
BedSlide(right, button type) for 146835
BedSlide (right, button type) for 146846 BedSlide (right, button type) for 146847
BedSlide (right, latch type) for 146062
BedSlide (right, latch type) for 146692
BedSlide (right, latch type) for 146723 BedSlide (right, latch type) for 146821 BedSlide (right, latch type) for 146828 BedSlide (right, button type) complete for Throat Plates
BedSlide (right, button type) complete for Throat
BedSlide (right, button type) complete for Throat
assembled.
Slide
(left)
725X
with no off-set, Nos. 1423X, 146006,146524, 146525
and
two
Plates with
146524,146525
Plates with
146525,146834
Name
Gear
Bevel
Bushing
Bushing
Stitch
Gasket
each
126150
Bushing Bushing
Bushing
Bushing
240C
3/64
in. off-set, Nos. 1423X, 146523,
and
3/32
in. off-set, Nos. 1423X,
and
(lower) Set Screw (2)
Gear (upper) Set Screw(2)
(upper)
(upper) Set Screw
RegulatorPlungercomplete,
(cork)
and
140734E
gear
(back) (back) Set Screw
(front)
(intermediate) Set Screw
two
240C
two
240C
alignment. Bed cannot
and 146511
Ring
and
146524,
two
PARTS
FOR
MACHINE
NO.
253-201
No.
146846
146847
146062
146692
146828
146723
146821
146525
146688 146689
1470X
146690 146691 146524
1423X
1470X
146652
143293
146528 146529 140061J
140050J 146530
56813
1519J
143031 143032 143033
131032
146854
146856
240C
893C
152C 313C
228E
Plate
25054
25067
25042
BedSlide (right,buttontype) complete forThroat
Plates with
146525,
BedSlide(right,button type) complete for Throat
Plates with
146525,.
BedSlide(right, latch type) complete forThroat
Nome
9/64
in. off-set, Nos. 1423X, 146524,
146848
and
two
3/16
in.off-set, Nos. 1423X,146524,
146849
and
two 240C
Plates with no off-set, Nos. 146061, 146688, 146689,
25057
25054
25042 25042
25042 25042
25042 25042 25042 25042 25042
25041
25041
25041
25041 25043 25043
25043 25043
25043
25043 25043 25043
25043
25057
NOTE:
25056
NOTE:
25055
NOTE:
146690,146691
BedSlide(right, latch type) complete for Throat
Plates with
146689,146690,146691
BedSlide (right, latch type) complete for Throat
Plates with
146690,
BedSlide (right, latch type) complete for Throat
Plates with
146690,146691,146722
BedSlide (right, latch type) complete for Throat
Plates with
146690,146691,146820
Bed Slide (right) Knob Bed Slide (right) Latch
BedSlide (right) LatchGuide
Bed Slide (right) Latch Guide Screw (2)
BedSlide(right)LatchSpring
BedSlide (right) Spring Bed Slide (right) Spring
Bed Slide (right) Spring Screw
BedSlide (right) Spring Screw (2) BedSlide (right) Spring Stop Screw (2)
Combination of Feed
Nos.
143087,
146775
Dummy
Shaft for 146652
Face
Plate
Face
Plate
Face
Plate
Face Plate Screw (upper)
Feed
Bar
Feed
Bar Screw
Feed Bar Screw Center (left) Clamping Screw
Feed
Bar Screw Center (right)
Feed Bar Screw Center (right) 313C with 1519J
Feed
Bar Screw
Feed
Bar
Feed
Bar
Feed Bar Screw Center Oil Wick Holder 143032 with
143031
Feed
Bar
FeedDog,17teeth (16teeth to the
felling,
•1/8 in.,5/32 in.-3/16 in.and
gauges, for 146763 and 146803
When ordering No. 131032,state gauge required.
FeedDogwithrowof teeth between needles, 17 Teeth
(14teeth to the inch)for piecingand goring, for
1/8
When ordering No. 146854, state gauge required.
When ordering No. 146856, state gouge required.
in. and
Feed
Dog
(14 teeth to the inch)for sleeving and straight run
lapseam
-5/16
and
four
3/64
in. off-set, Nos. 146687, 146688,
3/32
in. off-set, Nos.
146691,146827
9/64
in. off-set, Nos.
3/16
in. off-set, Nos. 146688, 146689,
and
Stitch Regulator Parts,
143134,143293,
and
146852
Gasket
Screw (lower) (3)
with
1607X
and
140695X
Center
(left)
Center
Screw
Screw
Screw
plain
with
Felling,
in. and
(right) Nut
Center
Oil
Center
Oil Wick
Center
Oil Wick
sewing
and
5/32
in. gauges, for 146855
rowofteeth
for3/16 in.,7/32 in.-1/4 in.,9/32 in.
11/32
in.
240C
1470X
and
four
1470X
146688,146689,
and
four
1470X
146688,146689,
and
four 1470X
and
four
1470X
146537,146545,
Wick
Holder
Holder
Screw
inch)
French
between
-3/8
forlop seam
seaming,
7/32
in.
needles,
in. gauges, for 146860
(2)
for3/32 in.
-1/4
in.
17teeth
10
PARTS
FOR
MACHINE
NO.
253-201
No.
146823
157J
140695X
1607X
147125 146852
1036AL
140566AL
140256AL 140568AL
140258AL
140333AL
1259AL
146534 146536
143039
223E
146537
140230C
1518J
146538
157J
52267
143042
146539
146540
50579J
50191C 52097
140488C
146662
146541
1513J
146542
146543
146544 143048
223E
146545 140230C
1518J
143050
157R
50191C
52097
1513J 140278C 143138
1513J
146546
143052
Plate
25054
NOTE: 25054
25043
25043
25036
25036 25036 NOTE:
25036
25036
25036
25036
25036
25043
25043 25043
25036
25036
25036
25043 25043 25043 25043
25043
25043
25043
25043
25043
25043
25043 25043 25036 25036 25036
25043
25043 25043
25043 25043
25043 25043
25043
Feed Dog, 16 teeth (14 teeth to the inch) for
Frenchseaming for
for
146826
When ordering No. 146823, state gauge required.
Feed Dog Screw Feed Dog
Feed DogStop Screw Nut
Feed
Feed Eccentric147125 with Feed EccentricBody
Feed EccentricBodySet Screw (3)..
Feed EccentricStop Screw(6 stitch)
No. 140566 isregularly furnished with thisMachine.
Stop
Eccentric
Feed EccentricStop Screw (7 stitch)
Feed
Eccentric
Feed Eccentric Stop Screw (14 stitch)
Feed
Lifting
Bevel
Gear
Feed LiftingEccentric
Bevel
Gear
Feed LiftingRockShaft... Feed
LiftingRock
Agents only)
Feed
Lifting
Feed
Lifting
Feed
Lifting
Feed LiftingRockShaft Connecting Rod Hinge Screw
Feed LiftingRock
Feed Lifting Rock
(for Agents only)
Feed LiftingRockShaft Crank Clamping Screw
Feed
Lifting
Feed
Lifting Lifting
Feed
Feed LiftingRock
Holder
Feed Feed
Feed
Feed
Feed
Feed
Feed Lifting Rock
Feed
Feed RockShaft complete, Nos. 143050 and 146542
Feed
Feed RockShaft
Feed RockShaft
Feed Rock Feed Rock
Feed RockShaft Connecting Rod Hinge Screw Nut
Feed
Feed
Feed
Feed
Feed Feed Feed Feed Rock
Feed
Feed
146539
Lifting
Holder
Screw
Lifting Lifting
with1513J
Lifting
Lifting
with
1513J
Lifting
Rock
Shaft
Rock
Shaft 146543 with 146546 (for Agents only)
Shaft Shaft
Rock
Shaft
Rock
Shaft Crank Clamping Screw
Rock
Shaft
Rock
Shaft
Rock
Shaft
Rock
Shaft
Rock
Shaft Shaft
Rock
Shaft
Rock
Shaft
Name
7/16
in. and
Screw
Stop Screw (8 stitch)
Eccentricand Arm Shaft (horizontal)
Position
Screw
and
Set
RockShaft RockShaft Cap Screw (2)
RockShaft Connecting Rod
RockShaft Crank Slide Blockwith Stud RockShaft Crank Slide BlockOil Wick RockShaft Crank Slide
Arm Shaft (horizontal)
Screw
(2)
Shaft
146534 with 146541 (for
Cap
Shaft
Connecting Rod Hinge Screw Nut...
Shaft
Crank with 50579J
Shaft
Crank Slide BlockOil Wick
with
143042
RockShaft Crank Slide BlockOil Wick RockShaft Screw Center (left)
RockShaft Screw Center (left) 50191C
Rock
Shaft Screw Center (right)
RockShaft Screw Center (right) 140488C
RockShaft Screw Center Front Oil Wick
Shaft
Screw
with
152C
Cap
Cap
Screw (2)
Connecting Rod Connecting Rod Hinge Screw
Crank
with
157R
Screw
Center
Screw
Center
Screw Center (left) Nut Screw Center (right) Screw Center (right) 140278C with 1513J.. Screw Center (right) Nut
Screw
Center
Screw
Center
Center
(left)
(left)
Front
Front
1/2
in.gauges,
and
Block
Oil Wick Holder.
Nut (2)
50191C
Oil
Wick
Oil
Wick
with
Holder
....
146540
1513J
PARTS
FOR
MACHINE
No.
146547
197E
146548 25044 Looper(bock)closedeye
1253AL
146549
1253AL
146550
146553
896AL
1259AL
146554
146556
146987
146923
51320AL
132790 164232 146557
146558
896AL
131927
51715AL
131928
146559
448AL
146948
1520J
128551
175E
1664J
146919 146936 146937 146938
51769C
146565 146739
146567 146647
146568 146569
*146570
143126
175E
896AL
231E
Plate
25043
25043
NOTE:
25044 25044
NOTE:
25044
25040 25040
25040
25040
25040
25040
25044
25044
25044
25040 25040 25040
25040
25040 25040 25040
25040
25040
25044 25044
25044
25044 25044 25044
25044
25044
25044
25044 25044
25044 25044
25044 25044 25040 25040
NOTEi
Feed
Rock
Shaft
143052
Feed
'
Whenordering No.
Looper(back) Set Screw Looper(front) closed eye
WhenorderingNo.146549,state gauge required.
Looper(front) Set Screw
LooperAvoiding LooperAvoiding
Looper
LooperAvoiding LooperAvoiding
LooperBallCrank
Looper
LooperBallCrank Arm146897 with 1520J, 128551 LooperBallCrank Arm Clamping Screw
LooperBallCrank Connection BallSleeve (two pieces) LooperBollCrank Connection BallSleeveGuide LooperBallCrank ConnectionNos.twoeach
LooperBallCrank Connection146557 with 132790,
Looper Looper Looper
Looper
Looper Looper Looper Looper Looper
Dueto the accuracy required for
ment,
separately
Looper
with 146541
Rock
Shaft
Screw
two
896AL
Avoiding
Sail Crank
and
146919
51715AL,
146556
and
Ball Boll BallCrank
BallCrank Connection Cop (upper) Screw
Stud Nut LockWasher (2) -
Boll Boll Boll BallCrank BallCrank
LockingPlate
Looper
Boll
Looper
BallCrank
Looper
Ball
Looper
Ball
Looper
BallCrank
LooperBailCrank
Looper
Ball
complete, Nos.29043,50169J,146732,146733.
146754,146904,146937
Looper
BallCrank
Looper
Holderwith
Looper
Holder
Looper
Holder
Looper
Holder
LooperHolder Clamping Screw
Looper
HolderHingePin
Looper
Holder
Looper
Holder
Looper
and
Holder
Looper
Rolder
SleeveAdaptor
Looper
Holder
Screw
146548,
131927
164232
Crank Crank
Crank
Crank
Crank
Crank Crank
Crank
Crank
146565
Bushing Bushing
Rock Rock
Holder
con
Rock
Rock
Rock
NO.
Name
Screw
Eccentric
Eccentric
Eccentric
Eccentric
Eccentric
Arm
and
Connection Connection Connection
Hinge Hinge Pitman Pitman Pitman
Pitman
Pitman
Pitman
Pitman
Pitman
Pitman
Pitman
Pitman
896AL
Shaftwith Shaft
Rock
onlybesent
Shaft
Shaft
Shaft
253-201
Center
Front
and
Center
Oil Wick
146546
Front Oil Wick
state gauge required.
withtwo
1259AL
Connection(forked)with
Connection
Set Screw(2) Slide
with
51320AL
131928
Pin PinSetScrew(2)
BallScrewStud
Ball Ball
End
End
End
Head
Rod
Rod146936with51769C
Rod
Rod
and two
with
(eccentric) Pin
Bracket.
Shaft
Bracket
Bracket
Bracket
Clamping
Block
Cap
(lower) Cap (upper)ScrewStud(2).. Cap (upper)ScrewStud(2)..
ScrewStud ScrewStud
Bearing
(left)
Bearing
(left)Nut
Bearing
(right)
(right)
with
with
Throw-out
and
two
51159J
Nut
1253AL
1664Jand 146567
with
146647
140439E
Looper
Bracket
cannot be
outasa
unit.
assembled.
Oil
Pipe
Oil
Plug
Holder
Holder
896AL,
Screw(2)
(right) (right) (right)
Cap
Cap
146948
Device
Rock
Shaft align
Arm,
Clamping Screw
Screw(2)
Nut Nut
Screw
Screw
supplied
Bed
11
(2)
(2)
and
12
No.
140734E
126150
146571
448AL
146572
448AL
140439E 146732
146733
51159J 146754 146904
50169J
29043
146924
146512
51283AL 146573 146574
146575
1133E
146576
1133E
140440J
146804
146805
146703
146580
146724
146581
146582 140552AL
1036AL
146725
175E
139110
139111
140542AL
146665
146666
50163XC
54865
146585
146586
402J
42483 25047 Needle Bar Thread Retainer Disc (2)
140546C
10107 25047 Needle BarThread RetainerSpring
146587 25045 Needle Clamp withtwo 1498F
146588 25042 Needle Guard, for 146644 25042 Needle Guard, for
PARTS
FOR
MACHINE
Plate
25037
25046
25040 25040
25040
25040
25044
25044 25044 25044
25044 25044 25044
25038
25038 25045
NOTE:
25045
25045 25045
25045 25045 25045 25045
25045
25045
25045
25036
25036 25036 25045 25045
25045
25045
25036
25047
25047
25047 25047 25047 25047
25047
25047
NOTE: NOTE: NOTE;
LooperHolder LooperHolder
LooperHolder
LooperHolder LooperHolder
LooperHolder RockShaft Bushing(front) Set Screw LooperHolder RockShaft Oil Plug Screw
Looper Throw-out Releoser
Looper
Throw-out
Looper
Throw-out
Looper Throw-out Sleeve
Looper
Throw-out Throw-out
Looper
LooperThrow-outSpring Screw Washer
Looper
Throw-out
Nos. 1520J, 128551, 146919
only)
MachinePulley(disc,power)"V" belt groove (outside
diameterofbelt
Machine PulleySet Screw (2)
Needle Bar (hollow)
Needle Bar complete, Nos. 146573 and 146587
When ordering No. 146574,state gauge required.
Needle Bar Bushing(lower) Needle Bar Bushing (lower) Set Screw
Needle Bar Bushing(upper) Needle Bar Bushing(upper) Set Screw
Needle Bar Bushing(upper) Oil Plug Screw
Needle Bar
Needle Bar Bushing(lower and upper) Oil Wick
complete, Nos. 146703,146804and two 146580
Needle Bar Bushing(lower and upper) Oil Wick
Clomp
and
Needle Bar Bushing(lower and upper) Oil Wick Clip (2).
Needle Bar Connecting
Needle
Bar Connecting Link
and
146725
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
Needle
Bar
10107,
140546C,
each
42483,
Needle
Bar
Needle
Bar
When ordering No. 146587, state When ordering No. 146588, state When ordering No. 146644, state gauge required.
NO.
253-201
Name
Rock
Shaft BracketScrew (2)
Rock
Shaft Bracket Screw Washer (2)
Rock
Shaft
Shaft Shaft
Bushing
Bushing Bushing
Rock Rock
ReleoserCap ReleoserCop Screw (2)
Spring SpringScrew
Deviceand PitmanRodcomplete,
groove
2.9
Bushing
(lowerand upper) Oil Wick
Retainer
Link
146585, 146665,
50163XC
Thread
Thread
Retainer
Retainer
3/32 3/16
and
in. to in. to
146724
54865
Bracket
Screw
(back)
(back) Set Screw (front)
and
146938 (for Agents
in.)
with
two
with
146582
146666
Screw
gauge
required.
5/32
in. gauges
gauge
required.
9/32
in. gauges
5li283AL
and
two
No.
146645
146845
146742
146743
190J
1498F
146591 143061
143062 143063
50257J
143370
51369E
146593
146594
146595
146596
143065 143066 146597
143124 143125 143126 143126
146659
146660 143071
146600 143073
50123E
146657
146658
146744
146745
146746
140553E 146700
146698
146696 146697
1364X
146747
146604
190J 190J
157E
189E
228E
Plate
25042
NOTE:
25042
NOTE:
25042 25042
25042
25042 25042 25045
25046
25046
25046
25046 25046
25046
25046
25046
25010
25010
25010
25046
25046
25046
25010
25010 25046
25046
25046
25046 25046
25046
25036 25046 25046 25046 25037 25037
25037 25037
25037
25037 25037 25037
25037
25037
25040
PARTS FOR
When
When
MACHINE
Needle Guard, for
ordering
ordering
Guard Guard
Guard
Guard
Guard
Set
No.
No.
Holder Holder
Holder Bracket Screw
Holder Screw
Screw
Screw (2)
Needle Guard, for
Needle Needle
Needle
Needle
Needle
Needle
Oil FlowBody
NO.
Nome
5/16
in.to
146645,
stategauge
7/16
in.and
146845,
state gauge required.
Bracket
253-201
3/8
in.gauges
required.
1/2
in.gauges
Oil Flow BodyGasket (2)
Oil Flow Window
Oil FlowWindow Cap
Oil FlowWindow Cap Screw (4)
Oil
Lead
Oil
Lead
Screw
Oil Pipe, for 146597
OilPipewithtwoeach 143124 and 143125for oiling
BedRotaryShaft Intermediate Bearing
Oil Pipe withtwoeach 143124 and 143125 for oiling
Looper RockShaft Hinge Pin
Oil Pipe with two each 143124 and 143125 for oiling
Thread (under) Take-upShaft FrontBearing
Oil Pipe Clamping Sleeve for 146597
Oil Pipe Clamping Sleeve Nut for 146597
Oil Pipe complete,
(horizontal) Center Bearing, Nos. 143065, 143066
from
Oil Pumpto ArmShaft
and 146593 (for Agentsonly)
Oil Pipe Clamping Sleeve (6)
Oil Pipe Clamping Sleeve Nut (6)
Oil Pipe ClampingSleeve Adaptor for 146660 (3)
Oil Pipe Clamping Sleeve Adaptor (fastened to Bed)(2)...
Oil Pump(centrifugal) Body Oil Pump(centrifugal) Body146659 withthree 143126
Oil Pump (centrifugal) Body PositionPin (2) Oil Pump (centrifugal) Body Screw (3)
Oil Pump(centrifugal) Cover Oil Pump(centrifugal) Impeller
Oil Pump (centrifugal) Impeller
Oil Pump(centrifugal) Screen Oil Pump(centrifugal) Screen Frame
Oil Pump (centrifugal) Screen Frame Screw (3)
Oil Removing Wick
Oil RemovingWick (head end) Hoider Body
Oil
Removing
with 146698
Oil Removing Wick (head end) Hoider Body Hinge Screw.
Oil RemovingWick (head end) Hoider Body Stop
Spring Ciip
Oil
Removing
Spring Clip Screw
Oil RemovingWick (head end) Holder BodySpring
Oil Removing Wick (head end) Hinge Plate
Oil Removing Wick
Gasket
Oil Removing Wick
Screw
(3)
Oil Removing Wick
Nos.
228E,
146744
Oil Wick for oiling Looper Ball Crank Pitman End
Bearing (left)
(head
Wick (head end) Hoider Body 146745
and
146744 (for Agents only)
Wick (head end) Holder BodyStop and
(head
(head
(head
140553E,
and
146745
Locking
Screw
end)
end)
Hinge Plate
end)
Hinge Plate
end) Holder Body complete,
146696,
146698,146700,
and
and
and
and
Cover
Cover
Cover
13
14
No.
146605
193E 146606 140239AL 139462
146751
1133E
146694
1057AL
146676
807X
146608
146609
161X
802X 146610 146611 146612 146752
190J
146729
26276 146712 146713
146837
26276
91 GAL
1695J
146838
146839
146761
26276 146712 146762
146862
146851
26276
37160
26276
146850 146858
26276
146859
146824
26276
910AL
1695J
146838
146825
PARTS FOR
Plate
25040
25040 25040
25040
25045
25045 25045 25045 25045 25049 25049
25049
25049
25049 25049
25049 25045 25045
25045
25045 25058 25058
25058 25058
When ordering No. 146713, state
NOTE:
25056 25056 25056 25056
25056
25056
When ordering No. 146839, state
NOTE:
25057 25057 25057 25057
NOTE:
When ordering No. 146762,state gauge required.
25055 25055 25055 25055 25055 25055
25055
25055 25055
When ordering No. 146859, state
NOTE: 25054 25054
25054 25054
25054
25054
NOTE:
When ordering No. 146825, state gauge required.
MACHINE
Oil
Wick
Holder
Oil
Wick
Holder
Oil
Wick
Position
Oil
Wick
Position
Presser
Bar
Presser Bar Bushing (lower) Presser Bar Bushing (lower) Set Screw
Presser
Bar
Presser Bar Guide BracketClamping Screw
Presser Bar LiftingBracket Lifter
Presser Bar Lifting Bracket Lifter Hinge Screw
Presser Bar Lifting Lever
Presser Bar Lifting Lever Extension
Presser Bar LiftingLever Extension Screw (2) Presser Bar LiftingLever Hinge Screw Presser Bar LiftingLever Spring
Guide
Tube
Bracket
Bracket
Bracket
NO.
Name
Bracket
with
Screw
with
Presser Bar Spring
Presser Bar Spring Guide Pin Presser Bar Stop with 190J Presser Bar Stop Clamping Screw
Presser
Foot
Presser Foot Plate Hinge Pin
Presser
PresserFoot (hinged) complete for LapSeam Felling,
for
and
Presser
Presser Foot Plate Hinge Pin Presser Foot Plate Hinge Pin Set Screw Presser Fool
Presser
Presser Foot (hinged) complete for Piecing or Goring,
Presser
Presser Foot Plate Hinge Pin
Presser
PresserFoot (hinged) complete for plain sewingand
Presser Presser
Presser Foot Plate Connection Hinge Pin
Presser Foot Plate Connection Spring
Presser Foot
Presser
Presser Foot Yielding Heel
Presser Foot Yielding Heel Hinge Pin
PresserFoot(triple hinged) complete for sleeving and
Presser
Presser Foot
Presser Foot Plate Hinge Pin Set Screw Presser Foot Plate Hinge Pin Set Screw Nut
Presser
Presser Fool (hinged) complete for French seaming
Plate
Foot
Shank
3/32
in. to
1/2
146729
Foot
Foot
for
1/8
in. and
and
146838
Foot
Foot
French seaming, for
26276,146712
Foot Foot
Foot
straightrun lap seam fellingfor
gauges, Nos.
146862
and
Foot
Foot
for
7/16
and
146838
in. gauges, Nos. 26276, 146712
Plate
Plate
Hinge Pin Set Screw Nut
Shank
with
910AL
5/32
in. gauges, Nos. 26276,146837
Plate
Shonk
3/32
and
146761
Plate Plate
Connection
Plate
Hinge Pin
Shank
37160,146850,146851,146858,
three
26276
Plate
Plate
Hinge Pin
Shank
with
910AL
in.
and1/2
in.
253-201
Screw
140239AL
1057AL
gauge
and
gauge
in. to
gauge
gauges,
and
1695J
3/8
3/32
1695J
Nos.
required.
required.
in. gauges Nos.
in.to
3/8
required.
26276,146824
in.
No.
190J
140441W
51614W
146616
146775
146617
54242
176J
140239J
143085 143134
143086 143087
143088
143378
140549E
2102
51570C
140442C
146618
131740
59537 59538
146619 131696
54070
140443J
2102
51570C
32572 54988 54071 54872
146620
HOC
624AL 316C
1547J 50326C 59539
131741
59537
59538
131696 146795 146621
1029J
465AL 146622 146623 146624 146625 146603
Plate
25045
25045
25045 25069
25069
25050 25050 25050
25050 25036
25036 25036
25036
25036 25048 25048
25048
25048 25048 25048 25048
25048
25049
25049
25049
25049
25049 25049 25049 25049
25049
25049
25049 25049 25049
25049
25049 25049 25049
25049
25048 25040 25040 25040 25040
25047
25047
25047
PARTS FOR
MACHINE
Presser
Foot
Pressure Regulating Thumb Screw
Pressure Regulating Thumb Screw Nut
Set of Mated Gears for
ArmShaft (upright) Bevel
RotaryShaft BevelGear
Setof MatedGears forUpperShaft
Arm
Shaft
Lifting
Eccentric
Slack Thread Controller
SlackThreadController Clamp
NO.
253-201
Name
Screw
Lower
Shaft cansistingof
Gear
(lower)
(upright)
Bevel
Gear (upper)and Feed
and ArmShaft (horizontal)BevelGear..
and
consisting
SlackThreadControllerClampScrew
Slack
Thread
Stitch Regulator
Stitch Regulator 143085 with 140549E, 143086
143378
Stitch Regulator Stitch Regulator LockingSlide Ratchet Wheel Stitch Regulator
StitchRegulator
Stitch
Controller Position Screw
Locking Locking
Regulator
Locking
Locking
Slide
Slide Ratchet Wheel Pin
SlideSpring
SlideSpringScrew
Tension(looper thread) Disc(4)
Tension(looper thread) Regulating ThumbNut (2) Tension(looper thread) Screw Stud (2)
Tension
(looper thread) Screw Stud 140442Cwith
51570C(2)
Tension(looper thread) Spring (2) Tension(looper thread) Spring Bushing(large) (2)
Tension
(looper thread) Spring
Tension(looper thread) Thread Guard Tension(looper thread) Thread Guide (2)
Tension (needle thread) Bracket Tension (needle thread) Bracket Screw Tension (needle thread) Disc (4)
Tension(needle thread) Regulating ThumbNut (2) Tension(needle thread) Releasing Disc(2) Tension(needle thread) Releasing Pin(2)
Tension(needle thread) Releasing Shaft Tension(needle thread) Releasing ShaftCrank with
624AL
Tension(needle thread) Releasing Shaft Crank
Connecting
Tension(needle thread) Releasing Shaft Crank
Connecting LinkHinge Screw (2)
Tension(needle thread) Releasing Shaft Crank Set Screw..
Tension
Tension(needle thread) Releasing Shaft Stop Screw Nut...
Tension
Tension
51570C(2)
Tension(needle thread) Spring (2) Tension(needle thread) Spring Bushing(large) (2) Tension(needle thread) Spring Bushing(small)(2)
Tension
Thread (looper) Uncurler (2) Thread (looper) Take-up with 465AL
Thread (looper)Take-up Screw
Thread Oooper) Take-up Set Screw Thread (looper) Take-up Screw Washer (fiber) Thread (looper) Take-up Stripper
Thread (looper) Take-up Stripper Holder with 906AL Thread (looper) Take-up Stripper Plate
Thread (looper) Take-up Stripper Plate 146625 with
237J,
two
Link
(needle thread) ReleasingShaft Stop Screw
(needle
thread)
(needle
thread)
(needle
thread)
139148,146623,146624,146626,146628
190J..;
Bushing
(small)(2)
Screw
Stud
Guide
(2)
(2)
Screw Stud 50326C with
Thread
15
Bed
of
and
and
16
PARTS
FOR
MACHINE
NO.
253-201
No.
237J
146626
906AL
139148
146627
146628
146631
1628X
146671 146632
50027J
139158
139158
146629
140443J
146630
146633
7071
724J
146634
51460E 54095 68164
1449J
146635
146763
146803
146855
146860
146826
691F
190X
190J
237J
237J
229J
229J
217J
237J
176J
Plate
25047 25047 NOTE: 25047
25047 25047 25047
25047 25047
25047
25047
25048 25048
25048
25048
25048
25050
25050
25050 25050 25050 25050 25050 25050
25050
25050
25050
25050
25050
25045
25045
25045
25045
25045
25045
25058
NOTE:
25057
NOTE:
25056
NOTE:
25055
NOTE:
25054
NOTE:
25054
Thread (looper) Take-up Stripper Plate Screw
Thread (looper) Take-up Stripper Plate Support Plate (2)..
One
No.
146626Isscrewed
Thread (looper) Take-up Stripper Plate Support
Plate
Screw
Thread (looper) Take-up Stripper Set Screw Thread (looper) Take-up Stripper Staple
Thread (looper) Take-up Stripper Staple Screw (2)
Thread (looper) Take-up Thread Guide (left)
Thread (looper) Take-upThread Guide (left)Screw
Thread (looper) Take-up Thread Guide (right)
Thread (looper) Take-up Thread Guide (right) Screw
Thread (looper) Thread Tube Thread (looper) Thread Tube Screw Stud Nut Thread (looper) Thread Tube Screw Stud Nut Washer Thread (looper) Thread Tube Thread Guide Thread (looper) Thread Tube Thread Guide Screw
Thread (looper) Thread Guide (left)
Thread (looper) Thread Guide (left) Screw (2)
Thread (looper) Thread Guide (right)
Thread (looper) Thread Guide (right) Screw (2)
Thread
(needle)
Thread
(needle)
Thread (needle) Thread Guide BracketSupport
Thread (needle) Thread Guide Bracket Support (lower)
Screw
Thread (needle) Thread Guide Bracket Support (upper)
Screw
Thread (needle) Eyelet (side of arm) Thread (needle) Eyelet (side of arm) PositionScrew Thread (needle) Eyelet (side of arm) PositionScrew
Washer
Thread (needle) Eyelet (side of arm) Screw
Thread (needle) Take-up with 51460E
Thread (needle) Take-up Clamping Screw
Thread (needle) Take-up Plate
Thread (needle) Take-up Spring
Thread (needle) Take-up Spring Screw
Thread (needle) Take-up complete, Nos. 1449J, 54095,
68164
and
Throat Plate for LopSeam Felling for
gauges
When ordering No. 146763, state
ThroatPlate for plain sewingand Frenchseaming
When
ThroatPlatefor
When ordering No. 146855, state
Throat Plate for sleeving
When ordering No. 146860, state
Throat Plate for French seaming for
When ordering No. 146826, state
Throat
for 131032
for
3/32
ordering
5/32
in.
seam felling for in.-5/16
1/2
in.
gauges,
Plate
(4)
Thread
Thread
146634
in. to
3/8
No. 146803,
Piecing
gauges,
for
3/16
in.
and
11/32
for 146823
Screw
(2)
Name
onto
Guide
Guide
in.
gauges
state
or Goring,for
146854
and
in.,
7/32
in.-3/8
Machine
Bed.
Bracket
Bracket Screw
3/32
in. to
gauge
required.
for 131032
gauge
required.
l/8
in.and
gauge
required.
straight run lap
in.-l/4
in.,
required.
7/16
required.
9/32
in.
and
in. gauges, for 146856.
gauge
gauge
1/4
in.
No.
146637 146638
146639 146693
146695
143308
12361
146640
41400
120344 120345
121741
120440 121108
120341
8908 23535 42850
146057 150855
No.
161084
161092
No.
161090
241755
146806
146807
240439
17822
124371
62827
146808
146809
146810 140224J
50222J
21202
No.
8068
7071
ACCESSORIES
Plate
25015
25015
25015 25015 25015
25016
25016 25015
25016 25016
25016 25016
25016 25016 25016 25016
25016
25016
25016 25016
Plate
25054
NOTE:
25063 EdgeFolder
NOTE:
Machine
Base
Machine Base
146693,146695 and two 146640 (for Agents only)
Machine Base
Machine
Base
Machine
Base
Pod (felt)
Machine Cushion (felt) (4)
Machine Hinge Connection (2)
Machine
Pad
Machine
Rest Pin
Oiler
with
Oiler Spout
One
Screw
Screw
Tweezers (curved)
Wrench
Wrench
Wrench
Wrench (socket) for 140552 Wrench (socket)
EDGE
EdgeGuide
120345
Quart
Driver
Driver
FOLDERS
1/4in. to 1/2in. needle
When ordering No. 161084, state needle gauge required.
3/16
in.to
When ordering No. 161092,state needle gauge required.
HEMMER
Plate
25065 Hemmer on Shank (turn down) for
NOTE:
insteps of
When ordering No. 161090, state size of hem and
sample
materialorfurnish
material.
Nome
and
Oil
Reservoir
and
Oil Reservoir 146637 with 146639,
and
Oil Reservoir
and
Oil
and
Oil
(felt) (2)
(wood)
Can of Light
ON
Name
with
Adjustable EdgeFolderon Shank,for
with
Adjustable EdgeGuideon Shankfor
1/2
in.needle gouge
ON
SHANK
Name
1/16
in.for hemmingoverall pockets
Reservoir
Reservoir
Grade
SHANK
gauge
Gasket
Oil
Oil
,
Stainless Oil
finished
FACE
and
Oil
Oil
241755
Oil
Oil
Oil
146810
Screw
Screw
Name
Pod
Pod
Pad Reservoir
Wick
Holder
Holder
Retainer
Washer
Rivet
7071,
Plate
25051
25051
25051
25051
25051
25051
25051
25051
25051
25051
25051 25051 25051
Thread
Lubricator Oil Pod (felt)
Thread
Lubricator
Thread
Lubricator
240439
Thread Thread
Thread
Thread
Thread
Thread Lubricator complete, Nos. 8068,17822,124371
Thread Lubricator 146808 with
Thread Lubricator Adaptor Thread Lubircator Adaptor Screw
Thread LubricatorAdaptor Screw Washer
Thread
Thread
and
Lubricator Lubricator
Lubricator Oil Reservoir Rivet
Lubricator Oil "Reservoir Rivet
Lubricator
and
146807
140224J
Lubricator
Lubricator
Return
Return
5/16
sample
146806
Washer
Washer
21202,
(felt)
.•
in. to
Wick
Wick
5/8
with
(inside)....
(outside)...
50222J,
Position
and
62827,
...
in. hem
furnish
sample
17
18
FITTINGS
FOR
LAP
SEAM
FELLING,
FOR
3/32
IN. TO
3/8
IN. GAUGES
No.
146523 146525
146524
1423X
146526
146531
160587
160619
160622
121449
1423J
139135
26276
146850
139134
146851
26276
37160
26276
146615
139490
26276
146850 139489 146851
26276 37160 26276
146753
146636
240C
Plate
25059
25059 25042
25042 25042 25059
25059 NOTE: 25059
NOTE:
25059
NOTE:
25059
NOTE:
25059 25059 25059
25059
25059 25059 25059
25059
25059
25059 25059
NOTE; 25059 25059
25059
25059
25059
25059
25059
25059 25059
NOTE:
25059
NOTE:
BedSlide (right)
Bed Slide (right) Knob
BedSlide(right)Spring
BedSlide (right) Spring Screw
BedSlide(right)SpringStop Screw (2)
BedSlide
Feed
When ordering No. 146531,state gauge required.
LapSeam Feller (adjustable) on Shank, for light, medium,
When ordering No. 160587, needle gauge of Machine and
weightofmaterial
LapSeam Feller(adjustable) an Shank for light, medium
When ordering No. 160619, needle gauge of Machine and
weight of material must be
LapSeam Feller on Shank withYielding(lower)scroll
When ordering No. 160622, needle gauge of
weight of material must be
LapSeam Feller Clamping Plate LapSeam Feller Clamping Plate Screw (2)
Presser
Presser Foot Plate Hinge Pin
Presser
Presser Foot Yielding Heel Presser Foot Yielding Heel Connection
PresserFoot Yielding Heel Connection Hinge Pin
PresserFoot
Presser Foot Yielding Heel Hinge Pin
PresserFoot(triplehinged) complete for
When ordering No. 146615, state gauge required.
Presser
Presser Foot Plate Hinge Pin
Presser
Presser Faot Yielding Heel
Presser Foot Yielding Heel Connection Presser Foot Yielding Heel Connection Hinge Pin
Presser Foot Yielding Heel Connection Spring
Presser Foot Yielding Heel Hinge Pin
Presser Foot (triple hinged) complete for
When ordering No. 146753, state
Throat Plate for
When ordering No. 146636, state gauge required.
(right,
Plates with
146524,
Dog, 15 teeth (14 teeth to the inch) for
mediumover light,mediumheavy over mediumand mediumheavy over heavyweightmaterial
and
medium
for
medium
Foot
Foot
5/16
in. gauges, Nos. 37160, 139134,139135,146850,
146851
and
Faat
Foot
3/8
in. gauges, Nos. 37160, 139489,139490,
146850,
Name
button-type) completeforThroat
3/64
in. off-set, Nos. 1423X, 146523,
146525
and
two
240C
must be
stated.
heavy over mediumweight
stated.
heavy and heavy weight material
stated.
Plate
Shank
Yielding
HeelConnectionSpring
three
26276
Plate
Shank
146851
and
three
26276
gauge
3/32
in. to
3/8
required.
in. gauges for 146531
146636
mate.rial
3/32
11/32
Machine
in.to
in.
and
and
FOR
LAP
SEAM
FELLING,
FiniNGS
FOR
3/32
IN. TO
3/8
IN. GAUGES
19
No.
146523
146525 146524
1423X
240C
146526
146772 25060 Feed Dog, 15 teeth (14 teeth to the inch) for 146773
160587 25060 LapSeam Feller(adjustable) on Shank for light, medium,
Plate
25060 25060 25042
25042
25042
25060
NOTE:
Bed
Slide
Bed
Slide
Bed
Slide
Bed
Slide
Bed
Slide
Bed
Slide
with
3/64
146525
and
When ordering No. 146772, state gauge required.
Name
in. off-set, Nos. 1423X,
two
240C
mediumover light, medium heavy over mediumand
146523,146524,
mediumheavy over heavy weight material
NOTE: When ordering No. 160587, needle gouge of Machine and
160619 25060 LapSeam Feller(adjustable) on Shank for light, medium
160622 25060 Lap Seam Feller on Shank with
121449 25060 LapSeam Feller Clamping Plate
1423J 25060 LapSeam FellerClampingPlateScrew(2) .. .
139135
26276 25060 Presser Foot Plate Hinge Pin
146850
139134 25060 Presser Foot Yielding Heel
146851
26276 25060
37160 25060 Presser Foot Yielding Heel Connection Spring
26276 25060
146615 25060
139490
26276
146850
139489 25060 Presser Foot Yielding Heel
146851
26276 25060 Presser FootYieldingHeel Connection Hinge Pin 37160 25060 Presser FootYieldingHeel Connection Spring
26276 25060 Presser Foot Yielding Heel Hinge Pin
146753
146773
weight of material must be stated.
and medium heavy over mediumweight material
NOTE:
When ordering No. 160619, needle gouge of Machine and
weight of material mustbe stated.
NOTE: When ordering No. 160622, needle
25060
25060
25060
NOTE:
25060
25060
25060
25060
25060
NOTE:
25060
NOTE:
for mediumheavy and heavy weight material
weight of material must be stated.
Presser
Foot
Plate
Presser
Foot
Shank
Presser Foot Yielding Heel Connection Presser Foot Yielding Heel Connection Hinge Pin
Presser Foot Yielding Heel Hinge Pin
Presser
Foot(triplehinged)completefor
5/16
in.gauges, Nos.37160,139134, 139135, 146850,
146851
and
three
26276
When ordering 146615, state gauge required.
Presser
Foot
Presser Foot
Presser
Presser Foot Yielding Heel Connection
Presser
3/8
When
Throat
7/32 in.-l/4 in.,9/32 in.-5/16in.and 11/32 in.-
Whenordering No.
Plate
Plate
Foot
Foot
in.gauges, Nos.37160,139489,139490,146850,
146851
ordering
Plate
3/8
in.
Hinge Pin
Shank
(triple
hinged)
and
three
26276
No.
146753,
for3/32 in.-l/8
gauges
for 146772
146773,
Yielding
(lower)scroll
gauge
complete
for11/32 in.and
stategauge
in.,
5/32 in.-3/l6
required.
stategauge required.
of Machine and
3/32
in.to
in.,
20
No. 146834 146525 146524
1423X
146835
146836
161091
121449
1423J
146837
26276
1695J 146838 146839
146840
240C
91 GAL
FOR
lAP
TERIALS
FOR
5/32
Plate
25061 25061 25042 25042
25042
25061
25061
NOTE:
25061
NOTE:
25061
25061
25061 25061
25061
25061 25061
25061
NOTE:
25061
NOTE:
FiniNGS
SEAM
FELLING LIGHTTOHEAVYWEIGHT
FOR
SLEEVING,
IN. TO
Bed Slide (right) Bed Slide (right) Knob
BedSlide (right) Spring BedSlide (right) Spring Screw BedSlide (right) Spring Stop Screw (2)
Bed Slide (right, button-type) complete for Throat
Feed Dog with row of teeth between needles, 17 teeth
When ordering No. 146836, state gouge required.
LapSeam Feller(adjustable) on Shank withYielding
When ordering No. 161091, needle gouge of Machine and
weight of material must be stated.
LapSeam Feller Clamping Plate LopSeam Feller Clamping Plate Screw (2)
Presser
Presser Foot Plate Hinge Pin
Presser Foot Plate Hinge Pin Set Screw
Presser Foot Plate Hinge Pin Set Screw Nut
Presser
PresserFoot (hinged) complete, Nos. 26276,146837
WhenorderingNo. 146839,state gauge required.
ThroatPlate for
When ordering No. 146840,state gauge required.
3/8
IN. GAUGES
Plates with
146525,
(14 teeth to
PIECING AND
3/32
146834
the
inch) for
GENERAL
Nome
in. off-set, Nos. 1423X. 146524,
and
two
240C
146840
lowerscroll, for light to heavy weight materials
Foot
Plate
Foot
Shank
with
910AL
and
and
146838
5/32
in.to
3/8
in.gauges, for 146836
MA
WORK,
1695J
FITTINGS
FOR
PIECING
No. 146523 146525 146524
1423X
146526
146836
160944
161093
121449
1423J
146837
26276
240C
UNDERWEAR,
Plate
25062 Bed Slide (right)
25062 Bed Slide (right) Knob
25042 BedSlide (right)Spring
25042 BedSlide (right) Spring Screw
25042 BedSlide(right)Spring Stop Screw
25062 BedSlide (right, button-type)complete forThroat Plates
25062 Feed Dog with row of teeth between needles, 17 teeth
NOTE:
25062 Lap Seam Feller (adjustable) on Shank for light to
NOTE: 25062 LapSeam Felleron Shank for light and
NOTE: 25062 Lap Seam Feller Clamping Plate
25062 LapSeam FellerClampingPlate Screw(2)
25062
25062 Presser Foot Plate Hinge Pin
with
146525
(14 teeth to
Whenordering No. 146836,state gauge required.
heavy weight material
When ordering No. 160944, needle gouge of Machine and weightof material mustbe specified.
material
When ordering No. 161093, needle gauge of Machine and
weight of
Presser
FOR
5/32
IN.TO
3/8
IN. GAUGES
Name
3/64
in. off-set, Nos. 1423X, 146523,146524,
and
two
240C
the
inch) for
146840
material
must be
stated.
Foot
Plate
medium
weight
No.
1695J
146838 146839
146840
FiniNGS
GAL
Plate
25062 25062 25062 25062
NOTE:
25062
NOTE:
FOR
SLEEVING,
Presser Foot Plate Hinge Pin Set Screw Presser Foot Plate Hinge Pin Set Screw Nut
Presser
Foot
PresserFoot (hinged) complete, Nos. 26276,146837
and
Whenordering No. 146839,state gauge required.
FIRST
146838
ThroatPlate for
OPERATION
FOR
5/32
FITTINGS
91
Shank
5/32
FOR
IN. AND
Name
with
910AL
in.to
IMITATION
3/16
and
1695J
3/8
in.gauges for 146836.
SINGLE
NEEDLE
IN. GAUGES
21
No.
146848
146525 146524
1423X
146846
146711
161092
160588
1174J
146761
26276 146712 146762
146714
No.
146523
146525
146524
1423X
146526
161084
121449
1423J
240C
FOR
240C
Plate
25063 25063 25042 25042
25042 25063
25063
NOTE: 25063
NOTE: 25063 25063 25063 25063 25063 25063
NOTE:
NOTE:
FRENCH
Plate
Bed Slide (right)
Bed Slide (right) Knob BedSlide (right) Spring BedSlide (right) Spring Screw
BedSlide (right) Spring Stop Screw (2)
BedSlide(right, button-type) completefor Throat
Plates with
146525,146848
Feed
Dog with row of teeth
(14 teeth to the inch) for
for
146714
When ordering No. 146711, state
Edge Folder withAdjustable Edge Guide on Shank for
3/16
When ordering No. 161092, state gouge required.
When ordering No. 146762, state gauge required.
25063
When ordering No. 146714,state gauge required.
LA
25064
25064
25042 25042 25042 25064
25064
NOTE:
When ordering No. 161084, state needle
25064
25064
in. to 1/2in. gauges
Edge Folder Clamping Plate Edge Folder Clamping Plate Screw (2)
Presser
Foot
Presser Foot Plate Hinge Pin
Presser
Foot
Presser Foot (hinged) complete, Nos. 26276,146712
and
146761
Throat Plate for
FITTINGS
Bed Slide (right)
Bed Slide (right) Knob
Bed Slide (right) Spring BedSlide (right) Spring Screw BedSlide (right) Spring Stop Screw (2)
BedSlide (right button-type) complete for Throat Plates
with
3/64
146525
Edge Guide with Adjustable Edge Folder on Shank for
Edge Guide with Adjustable Edge Folder on Shank
Edge Guide with Adjustable Edge Folder on Shank
and
1/4
in. to
ClampingPlate
Clamping Plate Screw (2)
Name
9/64
in. off-set, Nos. 1423X, 146524,
and
two
240C
between
5/32
Plate..
Shank
5/32
in.to
3/8
Name
in. off-set, Nos. 1423X,
240C
1/2
in. needle
gauge
needles, 14 teeth
in. to
3/8
in. gauges
gauge
required.
in. gauges for 146711.
146523,146524,
gauge
required.
22
FiniNGS
No.
1-16841
146842
26276
910AL
1695J 146838 146843
146844
FOR
No.
146834 146525 146524
1423X
240C
146835
146715
161090
121449
1423J
161085
26276
910AL
1695J
146838 161086
161087
26276
906AL
1695J
161088 161089
146718
Plote
25064
NOTE:
25064 25064 25064
25064
25064 25064
NOTE: 25064 NOTE:
HEAAMING
Plote
25065 25065 25042 25042 25042 25065
25065
NOTE:
25065
NOTE:
25065
25065
25065 25065 25065 25065 25065 25065
NOTE:
25065
25065
25065
25065
25065 25065
NOTE:
25065
NOTE:
Feed Dog, 17 teeth (16 teeth to the inch) for 146844...
When ordering No. 146841, state
Presser
Foot
Presser Foot Plate Hinge Pin
Presser Foot Plate Hinge PinSet Screw
Presser Foot Plate Hinge Pin Set Screw Nut
Presser
Foot
Presser Foot (hinged) complete, Nos. 26276,146838
and
When ordering No. 146843, state
When ordering No. 146844, state gauge required.
OVERALL
146842
Throat Plate for
FITTINGS
POCKETS
Bed
Bed
Bed
Bed
Bed
Bed
with
3/32
146834
andtwo240C
Feed Dog with row of teeth
(10 teeth to the inch) for
When ordering No. 146715, state
Hemmer on Shank (turn down) for
hem insteps of
When ordering No. 161090,
sample material or
material.
Hemmeron Shank (turndown)Clamping Plate
Hemmeron Shank (turndown) ClampingPlate Screw(2)....
Presser
Foot
Presser Foot Plate Hinge Pin Presser Foot Plate Hinge Pin Set Screw
Presser Foot Plate Hinge PinSet Screw Nut
Presser
Foot
Presser Foot (hinged) complete for inserting labels
hemming overall pockets, Nos. 26276,146838
161085
Whenordering No. 161086,state gauge required.
Presser
Foot
Presser Foot Plate Hinge Pin Presser Foot Plate Hinge Pin Set Screw
Presser Foot Plate Hinge Pin
Presser
Foot
Presser Foot (hinged) complete for sewing overall
material,
When ordering No. 161089, state gauge required.
Throat Plate for
When ordering No. 146718,state gauge required.
Name
gauge
and
gauge
in.
IN. TO
required.
1695J
required.
gauges
3/8
for 146841.
IN. GAUGES
Plate
Shank
3/8
FOR
with
in. to
3/16
Name
910AL
1/2
in. off-set, Nos. 1423X, 146524,146525,
between
needles, 13 teeth
146718
gauge
required.
5/16
1/16
Plate
Shank
Plate
Shank
Nos.
26276,161087
3/16
in
state
furnish
finished sample and sample
with
910AL
Set
with
906AL
in.to
3/8
in. to
size of hem
and
1695J
Screw Nut
and
1695J
and
161088
in. gauges for 146715
5/8
and
and
in.
furnish
and
FOR
PLAIN
SEWING, FOR
FiniNGS
3/32
IN. TO
3/8
IN. GAUGES
23
No.
146523
146525
146524
1423X
146526
146802
146711
146761
26276 146712 146762
146803
146778
No.
146849
146525 146524
1423X
146847
161100
161091
121449
1423J
161098
26276
146850 139134
146851
26276
37160
26276
161099
161101
240C
240C
Plate
Nome
25066 Bed Slide (right)
25066
25042 Bed Slide (right) Spring
25042 Bed Slide (right) Spring Screw 25042 Bed Slide (right) Spring Stop Screw (2)
25066 BedSlide(right, button>type) complete for Throat Plates
25066 Feed Dog, 17 teeth (16 teeth to the inch) for
NOTE:
25066 Feed Dog with row of teeth between needles, 14 teeth
NOTE: When ordering No. 146711, state
25066
25066 Presser Foot Plate Hinge Pin
25066
25066 PresserFoot (hinged) complete for
NOTE: When ordering No. 146762, state 25066 Throat Plate for NOTE: When ordering No. 146803, state gouge required. 25066 Throat Plate for
NOTE:
FOR LAP SEAM FELLING FOR REGULAR
Plate
25067 25067
25042
25042
25042
25042
25067
NOTE:
25067
NOTE:
25067 25067 25067
25067
25067 25067
25067
25067
25067
25067 25067
NOTE:
25067
NOTE:
Bed Slide (right) Knob
with
3/64
146525
and
When ordering No. 146802,state gauge required.
(14 teeth to the inch) for
for
Presser
Presser
gauges,
When ordering No. 146778, state gouge required.
FOR
13/32
Bed Slide (right) Bed Slide (right) Knob
Bed Slide (right) Spring BedSlide (right) Spring Screw Bed Slide (right) Spring Stop Screw (2)
BedSlide (right, button-type) complete for Throat Plates
with
146849
Feed Dog with row of teeth between needles, 17 teeth
(14 teeth to the inch) for 161101
When ordering No. 161100, state gouge required.
LopSeam Feller(adjustable) on Shankwith
lowerscroll, for lightto heavy weight materials
When ordering No. 161091, needle
weight of material mustbe specified.
LapSeam Feller Clamping Plate LapSeam FellerClampingPlate Screw(2)
Presser
Presser Foot Plate Hinge Pin
Presser
Presser Foot Yielding Heel
Presser Foot Yielding Heel Connection
Presser Foot Yielding Heel Connection Hinge Pin
Presser Foot Yielding Heel Connection Spring
Presser Foot Yielding Heel Hinge Pin
PresserFoot (triple hinged) complete, Nos.37160,
When ordering No. 161099, state gouge required.
Throat Plate for
When ordering No. 161101, state
in. off-set, Nos. 1423X, 146523,146524,
and
two
240C
1/8
in. gauges, for 146803
146778
5/32
gauge
Foot
Plate
Foot
Shonk
Nos.
26276,146712
3/32 5/32
FiniNGS
IN. TO
1/2
Name
3/16
in. off-set, Nos. 1423X,
and
two
240C
Foot
Plate
Foot
Shank
IN. GAUGES
in. and in. to
and
gauge
3/8
3/8
in. gauges, for 146711....
139134,146850,146851,161098
11/32
in. to
1/2
gauge
in. to
3/8
required.
3/32
in.to
146761
required.
in. gauges, for 146802.
WORK,
146524,146525,
gauge
and
in. gauges for 161100
required.
3/32
in.
in. gauges,
3/8
in.
Yielding
of Machine and
three
26276
24
FITTINGS
FOR LAP SEAM FELLING FOR HEAVY WORK,
FOR
13/32
IN. AND
1/2
IN. GAUGES
No.
146849
146525 146524
1423X
146847
161100
161091
121449
1423J
161095
26276 146850 161096 146851
26276
37160
26276 161097
161101
240C
Plate
25068
25068 25042 25042
25042
25068
25068
NOTE:
BedSlide (right)
Bed Slide (right) Knob
BedSlide (right) Spring
BedSlide(right)Spring Screw BedSlide (right)Spring Stop Screw(2) BedSlide(right, button-type) complete for Throat
Plates with
146525,146849
Feed Dog with row of teeth
(14teeth
When ordering No. 161100, state
Name
3/16
in. oft-set, Nos. 1423X, 146524,
and
two
240C
to the inch) for 161101
between
gauge
needles, 17
required.
teeth
25068 Lap Seam Feller (adjustable) on Shank with Yielding NOTE:
25068 Lap Seam Feller Clamping Plate
25068 LapSeam Feller Clamping Plate Screw (2)
25068
25068
25068
25068 25068 Presser Foot Yielding Heel Connection
25068 Presser Foot Yielding Heel Connection Hinge Pin
25068 PresserFoot
25068 Presser Foot Yielding Heel Hinge Pin
25068 Presser Foot (triple hinged) complete, Nos. 37160,
NOTE: 25068 Throat Plate for
NOTE:
lower scroll, for light to heavy weight materials
When ordering No. 161091, needle
weight of material must be stated.
Presser
Foot
Foot
Plate
Shank
Yielding
HeelConnectionSpring
11/32
in.to 1/2in.gauges for 161100
Presser Foot Plate Hinge Pin
Presser
Presser Foot Yielding Heel
146850,146851,161095,161096
When ordering No. 161097, state gauge required.
When ordering No. 161101,state gauge required.
gauge
and
of Machine and
three
26276
25
No. 6439
4879 56864 56865
126249
4882
126250
150451
150452
No.
146764
56865
46865 146765 146766 143283 143285
143284 140351AL
356C
2767
356C 6337 7125
356C
356C
146768
1115X 146769 146770
140351AL 146771
146779
FOOT
Plate
NOTE:
25030
25030 25030 25030 25030
25030
Plate
25030 25030
25030 25030
25030
25030
25030 25030
25030 25030 25030 25030
25030 25030 25030
25030
25030
25030
25030
25030
25030
25030
Chain, 36 in. to 45 in., with
When ordering No. 6439, state length required.
Chain Connecting Link Chain Hook (large) Chain Hook (small)
Treadle
Treadle
Treadle Shaft Spring
Treadle
LIFTER
Shaft
Shaft
Treadle complete, Nos. 4879, 4882, 126249,126250,
150451
and
KNEE
LIFTER
Chain,
10-1/4
Chain
Hook
Chain
Link
Rock
Shaft
Rock
Shaft
Rock
Rock
Rock
RockShaft Knee Arm Hub Clamping Screw
Rock
Rock Rock
RockShaft Lifting Bracket with two 356C Rock RockShaft Lifting Bracket Hook Set Screw
Rock
Rock
RockShaftSpring Screw
RockShaft Stop Dog (back) with 140351AL
Rock
Rock Rock
Knee
Hanger
Shaft
Knee
Shaft KneeArmcomplete, Nos. 2767,143283
and
143284
Shaft
Knee
Shaft
Knee
Shaft
Knee
Shaft
Knee
Shaft
LiftingBracket Hook
Shaft
LiftingBracket Set Screw
Shaft Spring
Shaft Stop Dog (front) with 140351
Shaft Stop DogClampingScrew(2) Shaft complete, Nos. 1115X,6337,7125,143285,
146765,146768,146769,146770 and two 146766
Lifter
PARTS
Name
Stand
two
wood
PARTS
Name
in., with 46865
with two wood screws 1 in.. No. 16 F.H. (2)
Arm
Arm
Hub
Arm
Hub
Arm
Plate
Arm
Plate
complete, Nos. 146764and 146771
56864
screws
with
Set
with Screw
1 in.
and
356C
Screw
356C
and
56865
No.16F.H.
56865
and
140351AL
AL
26
LAP
SEAM
FELLERS
No.
160587
160619
160622
160944
160945
160946
161091
161093
121449
1423J
Plate
25059 LopSeamFeller(adjustable)on Shank for light,
NOTE: When ordering No. 160587, needle
25059 Lap Seam Feller (adjustable) on Shank for light, medium,
NOTE:
25059 Lap Seam Feller on Shank with Yielding (lower) scroll for
NOTE: When ordering No. 160622, needle
25056 LapSeam Feller(adjustable)on Shankfor lightto heavy
NOTE:
25055 LapSeam Feller(adjustable) on Shank for lightto heavy
NOTE:
25058 LapSeamFeller(adjustable)on Shank for lightto heavy
NOTE:
25067 Lap Seam Feller (adjustable) on Shank with
NOTE:
25062 LapSeam Felleron Shank for lightand NOTE:
25055 Lap Seam Feller Clamping Plate 25055 LapSeam Feller Clamping Plate Screw (2)
medium
over light,
mediumheavy over heavy weight material
weightof material mustbe stated. ^
and mediumheavy over medium weight material
When ordering No. 160619, needle gauge of Machine and
weight of material must be
medium heavy
weight of material must be
weight material
When ordering No. 160944, needle gauge of Machine and
weight of material must be
weight
When ordering No. 160945, needle gouge of Machine and
weight of material must be
When ordering No. 160946, needle gauge of Machine and
weightofmaterial
When ordering No. 161091, needle gauge of Machine and
weight of material must be
When ordering No. 161093, needle gauge of Machine and
weight of
material
weight material
(lower)scroll,for lightto heavy weight materials
material
material
Nome
medium
stated.
and
heavy weight material
stated.
stated.
stated.
must be
stated.
stated.
must be
stated.
heavy over mediumand
gauge
gauge
medium,
of Machine
of Machine and
Yielding
medium
weight
and
Loading...
+ 59 hidden pages