SINGER 1120 User Manual

A

Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions
should always be followed, including the following:

Read all instructions before using this sewing machine.

DANGER

1. An appliance should never be left unattended when
plugged in.

2. Always unplug this appliance from the electric outlet
immediately after using and before cleaning.

3. Always unplug before re-lamping. Replace bulb with same
type rated 10 watts (110-120V area) or 15 watts (220-240V
area).

WARNING

shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is
necessary when this appliance is used by or near children.

2. Use this appliance only for its intended use as described in
this manual. Use only attachments recommended by the
manufacturer as contained in this manual.

3. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the appliance to
the nearest authorized dealer or service center for
examination, repair, electrical or mechanical adjustment.

4. Never operate the appliance with any air openings blocked.
Keep ventilation openings of the sewing machine and foot
controller free from accumulation of lint, dust, and loose
cloth.

- To reduce the risk of electric shock:

- To reduce the risk of burns, fire, electric

5. Keep fingers away from all moving parts. Special care is
required around the sewing machine needle.

6. Always use the proper needle plate. The wrong plate can
cause the needle to break.

7. Do not use bent needles.

8. Do not pull or push fabric while stitching. It may deflect the
needle causing it to break.

9. Switch the sewing machine off ("O") when making any
adjustments in the needle area, such as threading needle,
changing needle, threading bobbin, or changing presser foot,
and the like.

10.Always unplug sewing machine from the electrical outlet
when removing covers, lubricating, or when making any other
user servicing adjustments mentioned in the instruction
manual.

11.Never drop or insert any object into any opening.

12.Do not use outdoors.

13.Do not operate where aerosol (spray products are being
used or where oxygen is being administered).

14.To disconnect, turn all controls to the off ("O") position, then
remove plug from outlet.

15.Do not unplug by pulling on cord. To unplug, grasp the plug,
not the cord.

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use only.

Congratulations

As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in

creativity. From the moment you first use your machine, you will know you are sewing on one of

May we recommend that, before you start to use your sewing machine, you discover the many

advantages and the ease of operation by going through this instruction book, step by step,

To ensure that you are always provided with the most modern sewing capabilities, the

manufacturer reserves the right to change the appearance, design or accessories of this

the easiest to use sewing machines ever made.

seated at your machine.

sewing machine when considered necessary.

Please note:

® Singer is a registered trademark of The Singer Company Ltd or its affiliates.

Copyright © 2005

All rights reserved throughout the world.

This Instruction Book covers the operation of multiple models of sewing machines and the use
of optional accessories. The manufacturer has made every effort to clearly define the
differences between the different models and to define when an accessory is an optional extra.
Please read carefully to determine which instructions apply to your particular model machine.
For a clear definition of your sewing machine please see pages 19.

List of contents

Principal parts of the machine.....................................................2/3

Accessories....................................................................................4

Fitting the snap-in sewing table .....................................................5

Connecting machine to power source............................................6

Changing the bulb..........................................................................7

Two-step presser foot lifter/ Adjusting presser foot pressure .........8

Attaching the presser foot holder

Winding the bobbin ......................................................................10

Inserting the bobbin......................................................................

Inserting and changing needles...................................................12

Threading the upper thread .........................................................13

Automatic needle threader (optional)...........................................14

Thread tension.............................................................................15

Raising the bobbin thread............................................................16

Reverse sewing/ Removing the work/ Cutting the thread............17

...................................................9

11

How to choose your pattern.........................................................19

Function of stitch width dial and stitch length dial........................20

Blind hem/ lingerie stitch..............................................................21

Overlock stitches (for models A, B & C).......................................22

Sewing on buttons .......................................................................23

Sew 4-step buttonholes ...............................................................24

Zippers and piping .......................................................................25

Sewing with the optional hemmer foot.........................................26

Multi-stitch zig-zag .......................................................................27

Straight stretch stitch and Ric Rac stitch (for models A, B & C) ....28

Honeycomb stitch ......................................29

Sewing with the optional cording foot ..........................................30

Free motion darning.....................................................................31

Practical stitches .......................................32

Maintenance ................................................................................33

(for models A, B & C)

(for models A, B & C)

Matching needle/ fabric/ thread....................................................18

Trouble shooting guide ................................................................34

Principal parts of the machine

1. Thread tension dial

2. Presser foot pressure adjustment

3. Thread take-up lever

4. Thread cutter

5. Presser foot

6. Needle plate

7. Removable sewing table/accessory storage

8. Bobbin stopper

9. Stitch length dial

10. Stitch width dial (not on all models)

11. Pattern indicator window

12. Reverse sewing lever

(not on all models)

1

2

3

4

8

9

10

11

5

6

7

2

12

Principal parts of the machine

13. Horizontal spool pin

14. Bobbin winder

15. Handwheel

16. Pattern selector dial

17. Power and light switch

18. Main plug socket

19. Bobbin thread guide

20. Upper thread guide

21. Face plate

22. Handle

23. Presser foot lever

24. Feed speed control

25. Power cord

13

14

15

16

17

18

19

20

21

22

23

24

25

3

Accessories

Standard a Optional accessoriesccessories

a. All purpose foot

b. Zipper foot

c.

Buttonhole foot

d.

Button sewing foot

e.

L-screwdriver

f.

Seam ripper/ brush

g. Oil bottle

h.

Pack of needles

I.

Bobbin (3x)

j. Seam guide

k. Darning plate

L. Spool holder

(These 6 accessories are not
supplied with this machine;
they are however available as
special accessories from your
local dealer.)

m.Satin stitch foot

n. Overcasting foot

o. Hemmer foot

p. Blind hem foot

q. Cording foot

r. Darning foot

Standard a riccesso es

a

006806008 006905008

e

i

b

f

j

c

006909008

g

k

Optional a iccessor es available at extra cost

d

006914008

h

l

m

006804008

p

4

n

006803008

q

006810008 006016008006812008

o

006800008

r

Fitting the snap-in sewing table

Keep the snap-in sewing table horizontal, and push it in the
direction of the arrow. (1)

The inside of the snap-in sewing table can be utilized as an
accessory box.

To open, lift up at the point of the arrow. (2)

5

Connecting machine to power source

Connect the machine to a power source as illustrated. (1)
For appliance is equipped with a polarized plug which must be

used with the appropriate polarized outlet. (2)

Attention:

Unplug power cord when machine is not in use.

Foot control

The foot control pedal regulates the sewing speed. (3)

Attention:

Consult a qualified electrician if in doubt as to connect
machine to power source.

Unplug power cord when machine is not in use.
The foot control must be used with the appliance by 4C-

316B (110-120V area) / 4C-326G (230V area) / 4C-316C or
4C-326C (220-240V area) manufactured by Panasonic Co.,
Ltd.(TW)

Sewing light

Press main switch (A) for power and light on " l ".

IMPORTANT NOTICE

For appliance with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way. If it does
not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the proper outlet. Do
not modify the plug in any way.

1

Polarized attachment plug

Conductor
intended to be grounded

2

6

A

3

Changing the bulb

Disconnect the machine from the power supply by removing
the plug from the main socket!

- Loosen screw (A) as illustrated. (1)

- Remove the face plate (B).

- Unscrew the bulb and install a new one (C). (2)

- Replace the face plate and tighten screw.

Should there be any problem, ask your local dealer for advice.

B

A

1

C

2

7

Two-step presser foot lifter

When sewing several layers or thick fabrics, the presser foot
can be raised for easy positioning of the
work. (A)

to a high rise position

Adjusting presser foot pressure

A

The presser foot pressure of the machine has been pre-set
and requires no particular readjustment according to the type
of fabric (light-or-heavy weight).

However, if you need to adjust the presser foot pressure, turn
the presser adjusting screw with a coin.

For sewing very thin fabric, loosen the pressure by turning the
screw counter , and for heavy fabric, tighten
by turning it clockwise.

counterclockwise

Tighten presser

Loosen

8

adjusting screw

Attaching the presser foot holder

Raise the presser bar (a). Attach the presser foot holder (b) as
illustrated. (1)

Attaching the presser foot

Lower the presser foot holder (b) until the cut-out (c) is directly
above the pin (d). (2)

Raise the lever (e).
Lower the presser foot holder (b) and the presser foot (f) will

engage automatically.

a

a

e

b

c

Removing the presser foot

Raise the presser foot. (3)
Raise the lever (e) and the foot disengages.

Attaching the seam guide

Attach the seam guide (g) in the slot as illustrated. Adjust
according to need for hems, pleats, etc. (4)

Attention:

Turn power switch to off ("O") when carrying out any of the
above operations!

d

b

12

e

34

9

f

g

Winding the bobbin

- Place thread and spool holder onto spool pin (1). For
smaller spools of thread place spool holder with small
side next to spool (2).

- Wind thread clockwise around bobbin winder tension
discs (3).

- Thread bobbin as illustrated and place on spindle (4).

- Push bobbin to right (5).

- Hold thread end (6).

- Step on foot control pedal (7).

- Cut thread (8).

- Press bobbin to left (9) and remove.

1

Please Note:

When the bobbin winder spindle is in "bobbin winding"
position, the machine will not sew and the hand wheel
will not turn. To start sewing, push the bobbin winder
spindle to the left (sewing position).

2

3

678

10

4

5

9

Inserting the bobbin

When inserting or removing the bobbin, the needle
must be fully raised.

- Open the hinged cover (1).

- Hold the bobbin case with one hand. Insert the bobbin
so that the thread runs in a clockwise direction (arrow)
(2).

- Pull the thread through the slit and under the finger (3).

- Hold the bobbin case by the hinged latch (4).

- Insert it into the shuttle (5).

Attention:

Turn power switch to off ("O") before inserting or
removing the bobbin.

12

3

4

5

11

Inserting and changing needles

Change the needle regularly, especially if it is showing signs of
wear and causing problems. For best sewing results always
use SINGER Brand Needles.

Insert the needle

A. Loosen the needle clamp screw and tighten again after

inserting the new needle. (1)
B. The flat side of the shaft should be towards the back.
C/D. Insert the needle as far up as it will go.

as illustrated as follows:

D

A

B

Attention:

Turn power switch to off ("O") before inserting or removing
the needle.

Needles must be in perfect condition. (2)

Problems can occur with:
A. Bent needles
B. Blunt needles
C. Damaged points

C

1

ACB

2

12

Threading the upper thread

This is a simple operation but it is important to carry out
correctly as by not doing so

.

result

several sewing problems could

- Start by raising the needle to its highest point (1), and also

raise the presser foot to release the tension discs. (2)

For safety, it is strongly suggested you turn off the

Note:

power before threading.

- Lift up the spool pin. Place the spool of thread on the holder

with the thread coming off the spool as shown. For small
thread spools, place small side of spool holder next to spool.
(3)

- Draw thread from spool through the upper thread guide. (4)

- Guide thread around thread guide (5) pulling thread through

pre-tension spring as illustrated.

- Thread tension module by leading thread down right

channel and up left channel (6). During this process it is
helpful to hold the thread between the spool and thread
guide (4).

- At the top of this movement pass thread from right to left

through the slotted eye of the take-up lever and then
downwards again. (7)

-

Now pass thread behind the thin wire needle clamp guide (8)
and then down to the needle which should be threaded from
front to back. Pull about 6-8 inches of thread to the rear
beyond the needle eye. Trim thread to length with built in
thread cutter.

Note:

If your sewing machine is equipped with the factory
installed optional automatic needle threader, instructions
for use can be found on page 14.

(9)

2

7

9

8

6

13

3

5

4

2

6

78 9

4

3

5

1

Automatic needle threader (optional)

* The automatic needle threader is a factory installed option. If

your machine has this option use the following instructions:

- Raise the needle to its highest position.

- Press lever (A) down as far as it will go.

- The threader automatically swings to the threading position

(B).

- Pass thread around thread guide (C).

- Pass the thread in front of the needle around the hook (D)

from bottom to top.

- Release lever (A).

- Pull the thread through the needle eye.

Attention:

Turn power switch to off ("O")!

A

B

A

B

C

1

A

C

D

D

14

2

Thread tension

Upper thread tension

Basic thread tension setting: "4"
To increase the tension, turn the dial to the next number up. To

reduce the tension, turn the dial to the next number down.
A. Normal thread tension for straight stitch sewing.
B. Thread tension too loose for straight stitch sewing. Turn dial

to higher number.
C. Thread tension too tight for straight stitch sewing. Turn dial

to lower number.
D. Normal thread tension for zig zag and decorative sewing.

Correct thread tension is when a small amount of the upper

thread appears on the bottom side of fabric.

Lower thread tension

To test the bobbin thread tension, remove the bobbin case and
bobbin and hold it by suspending it by the thread. Jerk it once
or twice. If the tension is correct, the thread will unwind by
about an inch or two. If the tension is too tight, it does not
unwind at all. If the tension is too loose, it will drop too much.
To adjust, turn the small screw on the side of the bobbin case.

Please note:

- Proper setting of tension is important to good sewing.

- There is no single tension setting appropriate for all stitch

functions, thread on fabric.

- A balanced tension (identical stitches both top and bottom) is

usually only desirable for straight stitch construction sewing.

- 90% of all sewing will be between "3" and "5" ("4" is basic

setting).

- For zig zag and decorative sewing stitch functions, thread

tension should generally be less than for straight stitch
sewing.

- For all decorative sewing you will always obtain a nicer stitch

and less fabric puckering when the upper thread appears on
the bottom side of your fabric.

4

12

BA

C

15

D

Raising the bobbin thread

Hold the upper thread with the left hand. Turn the handwheel
(1) towards you (counterclockwise) lowering, then raising
needle.

Gently pull on the upper thread to bring the bobbin thread up
through the needle plate hole (2). Lay both threads to the back
under the presser foot. (3)

1

16

2

3

Reverse sewing

To secure the beginning and the end of seam, press down the
reverse sewing lever (A). Sew a few reverse stitches. Release
the lever and the machine will sew forwards again. (1)

Removing the work

Turn the handwheel counterclockwise to bring the thread take
up lever to its highest position, raise the presser foot and
remove work behind (2)the needle and presser foot.

Cutting the thread

Pull the threads behind the presser foot. Guide the threads to
the side of the face plate and into thread cutter (B). Pull
threads down to cut. (3)

A

12

B

17

3

Matching needle/ fabric/ thread

NEEDLE, FABRIC, THREAD SELECTION GUIDE

NEEDLE SIZE

9-11 (70-80)

11-14 (80-90)

14 (90)

16 (100)

18 (110)

NEEDLE, FABRIC SELECTION

NEEDLES EXPLANATION TYPE OF FABRIC

SINGER

2020

SINGER

2045

SINGER 2025 Twin Needle. Woven fabrics and knits.

SINGER 2032 Leather needles. 12 (80) to 18 (110) Leather, vinyl, upholstery. (Leaves smaller hole than standard large needle.)

Note twin needle:

1. Twin needles, can be purchased for utility and decorative work.

2. When sewing with twin needles, the stitch width dial should be set at less than "3".

3. For best sewing results always use genuine SINGER needles.

4. Replace needle often (approximately every other garment ) and / or at first thread breakage or skipped stitches.

Lightweight fabrics-thin cottons, voile, serge, silk , muslin,
Qiana, interlocks, cotton knits, tricots, jerseys, crepes, woven
polyester, shirt & blouse fabrics.

Medium weight fabrics-cotton, satin, , sailcloth,
double knits, lightweight woollens.

Medium weight fabrics-cotton duck, woolen, heavier knits,
terrycloth, denims.

Heavyweight fabrics-canvas, woolens, outdoor tent and quilted
fabrics, denims, upholstery material (light to medium).

Heavy woollens, overcoat fabrics, upholstery fabrics, some
leathers and vinyls.

IMPORTANT : Match needle size to thread size and weight of fabric.

Standard sharp needles. Sizes range
thin to large. 9 (70) to 18 (110).

Semi-ball point needle, scarfed. 9 (70) to
18 (110).

FABRICS

THREAD

Light-duty thread in cotton, nylon ,polyester or
cotton wrapped polyester.

kettleciath

Natural woven fabrics-wool, cotton, silk, etc. Qiana. Not recommended for
double knits.

Natural and synthetic woven fabrics, polyester blends. Knits-polyesters,
interlocks, tricot, single and double knits. Also sweater knits, Lycra, swimsuit
fabric, elastic.

Most threads sold are medium size and suitable
for these fabrics and needle sizes. Use
polyester threads on synthetic materials and
cotton on natural woven fabrics for best results.
Always use the same thread on top and bottom.

Heavy duty thread, carpet thread. (Use heavy
foot pressure-large numbers.)

18

How to choose your pattern

At the start of this manual, you were informed that this book
covers the operation of multiple models of sewing machines.
The primary difference between the various models is the type
and number of stitch patterns. In addition to stitch patterns
there is also a difference in the number of dials used to modify
the patterns.

On all models stitch patterns are chosen by turning the stitch
pattern selector dial. The pattern on an alphabet letter depicting
the pattern will show in the stitch display window.
As you study the chart on the right while examining your sewing
machine you will be able to easily determine which model is
your sewing machine.

If you determine your sewing machine is either A or B model
pay attention to the instructions on the next page for stitch width
dial and stitch length dial.

If you have model C then ignore the instructions for stitch width
dial and only pay attention to stitch length dial.

If you have model D then all your pattern lengths and widths
are pre-set and you do not have length or width dials.

Stitch

pattern

Utility

1 2 3 4 5 6 7 8 9 10111213141516171819202122232425262728293031323334353637 38

Block satin

Model

3 DIALS

A

3 DIALS

B

2 DIALS

C

1 DIAL

D

Stitch width dial (models A & B)

Stitch length dial (models A, B & C)

A

Stitch display

Stitch pattern
selector dial
(models A, B,C&D)

Note:

For ease of operation the stitch patterns and stitch length dial are
color coded. For example to sew honeycomb pattern 19 the stitch
graphic is red and the "S1" on the stitch length dial is red.

Stretch

19

Buttonhole

Function of stitch width dial and stitch length dial

Function of stitch width dial

(for models A & B)

The maximum zigzag stitch width for zigzag stitching is 5mm;
however, the width can be reduced on any patterns. The width
increases as you move zigzag dial from "0" - "5". For twin
needle sewing, never set the width wider than "3" (1).

The stitch width dial is also the control for the straight stitch
infinite needle position. "0" position is full left, "5" is full right
and between "2" and "3" is center needle position.

Function of stitch length dial while zigzaging

(for models A, B & C)

The density of zigzag stitches increase as the setting of stitch
length dial approaches "0".

Neat zigzag stitches are usually achieved at "2.5" or below (2).

Closed up zigzag stitches are called satin stitches (2).

For straight stitch sewing, generally speaking, the thicker the
fabric, thread and needle, the longer the stitch should be.

Stitch width dial

()models A & B

54 3 2 10

2

2

3

3

1

1

4

4

0

5

5

0

1

Stitch length dial

(models A, B & C)

3

4

2

S

4

21

2

3

0.5

1

0

S

1

2

For model D the width of
Zig Zag Stitch Pattern
(only) is adjustable with
Stitch Pattern SelectorDial.

20

Blind hem/ lingerie stitch

* The blindhem foot is an optional accessory not supplied with

this machine.

For hems, curtains, trousers, skirts, etc.

Blind hem for stretch fabrics. (for models B, C & D)

Blind

hem/lingerie for firm fabrics.

Set the machine as illustrated (1).

Note:

It takes practice to sew blind hems. Always make a sewing
test first.

Fold the fabric as illustrated with the wrong side uppermost (2).
Place the fabric under the foot. Turn the handwheel forwards

by hand until the needle swings fully to the left. It should just
pierce the fold of the fabric. If it does not, adjust the stitch width
accordingly (3).

Adjust the guide (4) by turning the knob (5) so that the guide
just rests against the fold.

Sew slowly, guiding the fabric carefully along the edge of the
guide.

Turn the speed control to minimum!

It takes practice to sew

blind hems. Always make a sewing test first.

Stitch width dial

()models A & B

4

4

5

5

All purpose foot

1

2

2

2

3

3

1

1

0

0

Blindhem presser

foot (Optional)

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

3

0

S

1

5

4

21

Overlock stitches (for models A, B & C)

* The overcasting foot is an optional accessory not supplied

with this machine.

Seams, overcasting, visible hems.

Standard overlock

(A) : (for model A)

For fine knits, jerseys, neck edges, ribbing.

Double overlock stitch

(B) :

For fine knits, handknits, seams.

Stretch overlock

(C) :

For fine knits, jerseys, neck edges, ribbing.

All overlock stitches are suitable for sewing and overcasting
edges and visible seams in one operation.

When overcasting, the needle should just go over the edge of
the fabric.

Attention:

Use new needles or ball point needles to avoid skipping.

Stitch width dial

()models A & B

3

3

4

4

5

5

All purpose foot

2

2

1

1

0

0

Overcasting foot

(Optional)

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

0

S

1

22

AB C

Sewing on buttons

Install the darning plate. (A)

Change presser foot to button sewing foot. (B) Select zigzag
stitch.

Position the work under the foot. Place the button on the
marked position, lower the foot. Adjust stitch width to "0" and
sew a few securing stitches. Set the stitch width to number "3"

- "5". Turn the handwheel to check that the needle goes cleanly
into the left and right holes of the button (adjust the stitch width
according to the button), and slowly sew on the button with
about 10 stitches. Adjust the stitch width to "0" and sew a few
securing stitches (1).

If a shank is required, place a darning needle on top of the
button and sew (2). For buttons with 4 holes, sew through the
front two holes first (1), push the work forward and then sew
through the back two holes as described (2).

A

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

Stitch length dial

(models A, B & C)

1

2

3

4

2

S

Button sewing foot

B

0

S

1

23

1

2

Sew 4-step buttonholes

Prepare

1. Take off the all purpose foot and attach the buttonhole foot.

2. Measure diameter and thickness of button and add 0.3 cm

(1/8") for bar tacks; mark buttonhole size on fabric.

3. Place fabric under the foot, so that marking

on the
buttonhole foot aligns with starting marking on fabric. Lower
the foot, so that the buttonhole center line marked on the
fabric aligns with the center of the buttonhole foot.

Adjust the stitch length dial in the " " to set stitch density.

Note:

density varies according to the fabric. Always test sew a

buttonhole.

Follow the 4-step sequence changing from one step to another
with the stitch pattern selector dial. Take care not to sew too
many stitches in stages 2 and 4. Use seam ripper and cut
buttonhole open from both ends towards the middle.

Tips:

- Slightly reduce upper thread tension produce better results.

- Use a backing for fine or stretchy fabrics.

- It is advisable to use heavy thread or cord for stretch or knit
fabrics.

- The zig-zag should sew over the heavy thread or cord.

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

1

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

0

S

1

Buttonhole foot

234

24

Zippers and piping

Set the pattern selector dial to " " or " ".

Change to zipper foot.

The zipper foot can be attached right (1) or left (2) depending
on which side of the foot you are going to sew.

To sew past the zipper pull, lower the needle into the fabric,
raise the presser foot and push the zipper pull behind the
presser foot. Lower the foot and continue to sew.

It is also possible to sew in a length of cord, into a bias strip to
form a welt (3).

Set stitch length control between "1" - "4" (according to
thickness of fabric).

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

Zipper foot

Stitch length dial

(models A,B&C)

2

1

3

4

2

S

0

S

1

25

1

2

3

Sewing with the optional hemmer foot

* The hemmer foot is an optional accessory not supplied with

your machine.

For hems in fine or sheer fabrics.

Set the stitch pattern dial to " " or " ".

Change to optional hemmer foot.

Neaten the edge of the fabric. At the beginning of the hem, turn
under the edge twice by about 3 mm (1/8") and sew 4-5
stitches to secure. Pull the thread slightly towards the back.
Insert the needle into the fabric, raise the presser foot and
guide the fold into the scroll on the foot (1).

Gently pull the fabric edge towards you and lower the presser
foot.

Begin sewing, guiding the fabric into the scroll by holding it
upright and slightly to the left (2).

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

Hemmer foot

(Optional)

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

0

S

1

26

1 2

Multi-stitch zig-zag

Sewing on lace and elastic, darning, mending, reinforcing
edges, bar tacks.

Set the stitch pattern dial to " ".

Place patch in position. The stitch length can be shortened to
produce very close stitches. (1)

When mending tears, it is advisable to use a piece of backing
fabric to reinforce. The stitch density can be varied by adjusting
the stitch length. First sew over the center and then overlap on
both sides. Depending on the type of fabric and damage, sew
between 3 and 5 rows. (2)

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

All purpose foot

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

0

S

1

27

1

2

Straight stretch stitch and Ric Rac stitch (for models A, B & C)

Straight stretch stitch

Set the stitch pattern dial to " ".

Used to add triple reinforcement to stretch and hardwearing
seams.

Turn the stitch length dial to "S1".

The machine sews two stitches forwards and one stitch
backwards.

Ric Rac stitch

Set the stitch pattern dial to " ".

Turn the stitch length dial to "S1".

Adjust the stitch width dial to between "3" and "5".

Ric Rac Stitch is suitable for firm fabrics like denim,
corduroy, poplin, duck, etc.

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

0

5

5

All purpose foot

Straight stretch stitch

Stitch length dial

(models A,B&C)

1

S

0

1

S

2

4

2

3

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

0

5

5

All purpose foot

Ric Rac stitch

Stitch length dial

(models A,B&C)

1

S

0

1

S

2

4

2

3

28

Honeycomb stitch (for models A, B & C)

Seams, hems, T-shirts, underwear, etc.

Set stitch pattern selector on " ".

This stitch can be used for all types of jersey and woven
fabrics.

When using honeycomb stitch pattern for hemming sew at 1cm
(1/4") from the fabric edge and trim the surplus fabric.

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

All purpose foot

Stitch length dial

(models A, B & C)

1

S

0

1

2

S

2

4

3

29

Sewing with the optional cording foot

* The cording foot is an optional accessory not supplied with

your machine.

Decorative effects, cushions, tablecloths, etc.

Set stitch pattern selector on " ".

In addition to zig zag, various other stitches are suitable for
sewing on cord, e.g. blindhem, multi-stitch zig zag,

and

selected decorative stitches.

Insert the cord between the spring covering the cord groove
and the foot (1). The cord should run in the groove. One, two
or three cords can be sewn on. The stitch width is adjusted
according to the number of cords and the stitch selected (2).

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

Cording foot

(Optional)

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

0

S

1

1

2

30

Free motion darning

* The darning foot is an optional accessory not included with

your machine.

Set the pattern selector dial to " " or " ".(1)

Install the darning plate (2).

Remove the presser foot clamp (3).
Attach the darning foot to the presser foot holder. The lever (A)

should be behind the needle clamp screw (B). Press the
darning foot on firmly from behind with your index finger and
tighten the screw (C) (4).

First sew around the edge of the hole (to secure the threads)
(5). First row: Always work from left to right. Turn work by 1/4
and oversew.

A darning ring is recommended for easier sewing and better
results.

Note:

Free motion darning is accomplished without the sewing
machine internal feed system. Movement of the fabric is
controlled by the operator. It is necessary to coordinate
sewing speed and movement of fabric.

Stitch width dial

()models A & B

4

4

5

5

Darning foot

(Optional)

2

2

3

3

1

1

0

0

Note: Stitch length
cannot be controlled
with dial as feed
dogs are lowered.

1

3

Stitch length dial

(models A, B & C)

3

2

C

0

1

2

4

2

S

S

1

A

B

5

31

4

Practical stitches (for models A, B & C)

Set the machine as illustrated.

Turn the switch width dial and stitch length dial to the same
colour code and adjust to suit the fabric.

Shell stitch

(a)

For decorative edges.

Suitable for edges on sheer, fine and stretch fabrics. The larger
stitch should go just over the edge of the fabric to create the
shell effect.

Feather or Thorn Bridging Stitch

(b) (for modelsB&C)

For seams, place mats, tablecloths.

Decorative joining seam for a fagotted effect.

Rampart Stitch

(c)

Gathering with cord or shirring with elastic.

This stitch can be used for firm, thicker fabrics.

Stitch width dial

()models A & B

2

2

3

3

1

1

4

4

0

5

5

0

All purpose foot

Stitch length dial

(models A, B & C)

2

1

3

4

2

S

0

S

1

32

ab

c

Maintenance

Attention:

Disconnect the machine from the electricity supply by
removing the plug from the mains socket. When cleaning the
machine, it must always be disconnected from the electricity
supply.

Remove the needle plate:

Turn the handwheel until the needle is fully raised. Open the
hinged front cover and unscrew the needle plate screws with
the screw drived (1).

Cleaning the feed dogs:

Use the brush supplied to clean the whole area (2).

Cleaning and lubricating the hook:

Remove the bobbin case. Snap the two hook retaining arms (3)
outwards. Remove the hook race cover (4) and the hook (5)
and clean with a soft cloth. Lubricate at the point (6) (1-2 drops)
with sewing machine oil. Turn the handwheel until the hook
race (7) is in the left position. Replace the hook (5). Replace the
hook race cover and snap back the two hook retaining arms.
Insert the bobbin case and bobbin and replace the stitch plate.

Important:

Fabric fluff and threads must be removed regularly. Your
machine should be serviced at regular intervals at one of our
service agencies.

1

7

2

6

5

4

3

33

Trouble shooting guide

Problem Cause Correction

Upper thread breaks

Lower thread breaks

Skipped stitches

Needle breaks

Loose stitches

Seams gather or pucker

Uneven stitches, uneven
feed

The machine is noisy

The machine jams

1.The machine is not threaded correctly

2.The thread tension is too tight

3.The thread is too thick for the needle

4.The needle is not inserted correctly

5.The thread is wound around the spool holder pin

6.The needle is damaged

1.The bobbin case is not inserted correctly

2.The bobbin case is threaded wrong

3.The lower thread tension is too tight

1.The needle is not inserted correctly

2.The needle is damaged

3.The wrong size needle has been used

4.The foot is not attached correctly

1.The needle is damaged

2.The needle is not correctly inserted

3.Wrong needle size for the fabric

4.The wrong foot is attached

1.The machine is not correctly threaded

2.The bobbin case is not correctly threaded

3.Needle/fabric/thread combination is wrong

4.Thread tension wrong

1.The needle is too thick for the fabric

2.The stitch length is wrong adjusted

3.The thread tension is too tight

1.Poor quality thread

2.The bobbin case is wrong threaded

3.Fabric has been pulled

1.The machine must be lubricated

2.Fluff or oil have collected on the hook or needle bar

3.Poor quality oil has been used

4.The needle is damaged

Thread is caught in the hook

1.Rethread the machine

2.Reduce the thread tension (lower number)

3.Select a larger needle

4.Remove and reinsert the needle (flat side towards the back)

5.Remove the reel and wind thread onto reel

6.Replace the needle

1.Remove and reinsert the bobbin case and pull on the thread. The
thread should pull easily

2.Check both bobbin and bobbin case

3.Loosen lower thread tension as described

1.Remove and reinsert needle(flat side towards the back)

2.Insert a new needle

3.Choose a needle to suit the thread and fabric

4.Check and attach correctly

1.Insert a new needle

2.Insert the needle correctly (flat side towards the back)

3.Choose a needle to suit the thread and fabric

4.Select the correct foot

1.Check the threading

2.Thread the bobbin case as illustrated

3.The needle size must suit the fabric and thread

4.Correct the thread tension

1.Select a finer needle

2.Readjust the stitch length

3.Loosen the thread tension

1.Select a better quality thread

2.Remove bobbin case, thread and insert correctly

3.Do not pull on the fabric while sewing, let it be taken up by the machine

1.Lubricate as described

2.Clean the hook and feed dog as described

3.Only use good quality sewing machine oil

4.Replace the needle

Remove the upper thread and bobbin case, turn the handwheel
backwards and forwards by hand and remove the thread remands.
Lubricate as described.

34

021VG40102(C)( ) Jun/05
SINGER 1100(8000-4)