Form IsnSO
plomhor, 19:j;i
PRINTED IN U. S. A.
LIST
OF
PARTS
MACHINE No. 105-20
THE SINGER MANUFACTURING COMPANY
Coi'YiiuinT, U. S. A., 1932 and 1933,
i)Y The SiNOEH Manufactuhing Co.
Ai.e Rights Re.sbiived kou ai.i, Counthie.s
INSTRUCTIONS FOR OILING
Before starting the machine apply
Singer Cloth and Leather Oil to all oil
holes and bearings. Particular care should
be taken to see that a sufficient quantity
of oil is poured into the oil hole leading
to the oil reservoir at the back of the
machine. The main bearings of the ma
chine are lubricated by means of this oil
reservoir which should be kept filled with
oil. When the machine is in continuous
use, it should be oiled frequently.
Genuine Singer Needles should be used
Company's Trade Mark “SIMANCO.** 1
in Singer Machines.
These Needles and their Containers
are marked with the
Needles in Containers marked
**For Singer Machines**
are not Singer made needles.
INDEX
PAGE
A(x;ES8(nui';s............................................................................. 14
lil)(IE KoIA)KU................................................................................................... 14
Knee Liftek Pahts
Machine Base...................................................................................................... 15
Machine No. 105-20..................................................................... 7
Numekical List of Pahts.............................................................................. 17
'I'liuEAi) Unwinueh.......................................................................................... 15
..........................................................................................
14
INSTRUCTIONS FOR ORDERING
In (inlcriiiii from tliis list, use ONLY the [nirt NUMBER
in tljo EIRHT column.
The number stamped on a Sewing Machine Part is in every
case the nuniber of the single part only.
Every combination of parts sent out as such has its specific
number, which, although not stamped on the ijarls, must be
u.sed when ordering the combination.
Each number always indicates the SAME PART in whatever
list it appears, or for whatever machine.
riic letters after some of the numbers indicate the style of
finish only, as follows:
A—llardenetl. Polished, Nickel Plated and Buffed
B—Polisheil, Nickel Plated and Buffed
C—Hardened Only
1)—I’olished Only
E—Soft, Not Polished
E—Hardened and Poli.shcd
H—Blued
,J—Nickel Plated Only
K—Hardene<l and Nickel Plated
L—Bra.ss Plafeil
M—Oxidized
N—Japanned, Dull
P—Japanned, Bright
R—Merlized
'r—flopi)er Plated
T. A.—Hardened, Polished, Copper and Nickel Plated
T. B.—Copper and Nickel Plated and Polished
J'. J.—Copjier and Nickel Plated Oidy
J'. K.— Hardened, Copper and Nickel I'lated
'r. M. —Copper Plated and Oxidized
J'. L—Copper and Brass Plated
Z. B.—Poli.shcd, Nickel Plated, Buffed and Chromium Plated
Z. J.—Nickel and Chromium Plated
'I'hese letters MUS'h Bhl USED when they appear in the list;
and AETliR the number as in the list.
In this series;
The figu)'e.s in the second column refer only to the plates,
illustrating the parts, and are NOT TO BE USED in ordering.
Paris marked with an asterisk (*) are furnished only when
repairs are ma<le at factory.
When ordei ing parts which differ as lo Gauge (the distance
hetween seams) the (hinge, as well as the Number must be
given on order.
and Buffed
U —Zinc Plated
V.—Silver Plated
\y—Polished and Nickel Plated
Y Black Nickel I’lated Only
Z—Chromium Plated
I to 15tH) and rjlOOl to 51500 are Screw Nund>ers
1501 to 1800 and 51501 to 51800 are Nut Numbers
1801 to Jtltlt) and 51801 to 52000 are Roller Numbers
2001 to 50000 amt 52001 and upward arc mimlrers of
Maelu'ne Parts
LIST OF PARTS COMPLETE
FOR
/'li'/sr
MACHINE No. 105-20
FOR HEMMING SILK GLOVES AND SIMILAR WORK IN LIGHT
MATERIAL. TWO NEEDLES, ONE LOOPER. GAUGES Ui
AND i/g INCH. BALANCE WHEEL No. 59208. DIAMETER
OF BELT GROOVE 2% INCHES. SPEED 3500.
NO. NAME
*.5i)lit)9
------
Arm, U])i)er and lower (solid) with 1541)1
and Iwo 1.5405................................................
,59491 7365 Arm Rotary Shaft....................................................
.59523 7355 “ “ “ Bushing (hack) with
,52045 7355 Arm Rotary Shaft Bushing (back) Packing
128.5c’ 7304 Arm Rotary Sliaft Bushing (back) Set
52045...............................................................
(cotton)............................................................
Screw...............................................................
NO.
51)521
52045
4180
50525
52045
12S5c
50207
142:ìj
50208
1354c
424c
50401
50307
50308
50202
50402
1140('
50200
50440
50210
57234
.57235
4.57c
4.58c
.50211
8.S2c
.50403
170.1
*.50213
*,50104
51001c
7071
217k
.50405
I’.UrrS FOR M.\OHINF No. 10.5-20
l'[„\TK N.^MK
7355 ;\rin Rotary Shaft Hushing (front) with
5204.5.............................................................
7355 .\rm Rotary Shaft Hushing (front) Hacking
(cotton)
...........................................................
7304 ¿\rni Rotary Siiaft Hu.shing (front) S(0
Screw..............................................................
73.55 .Vrin Rotary Sliaft Hushing (intermediate)
witli 52015......................................................
7355 Arm Rotary Shaft Hushing (intermediate)
Packing (cotton)
.............................................
7301 Arm Rotary Shaft Hushing (intermediate)
Set Screw........................................................
7365 Arm Side Cover......................................................
7304 “ “ “ Screw
........................................
7305 Halance Wheel, 24ij in. diam., with 424c
and 13,54c
7304 Balance Wheel Position Screw
......................................................
..............................
7304 “ “ Set Screw.....................................
7307 Cloth Plate with ,50202..........................................
7305 “ “ Slide (left ).........................................
7305 “ “ “ (right)
.....................................
7304 “ “ Steady Pin.........................................
------
Cloth Plate comiilele, Nos. 50307, ,50308
and ,50401
7304 Cloth Plate S(a'cw
......................................................
..............................................
7305 k'eed Har with two each 45Sc and 882c. . .
------
“ “ ,50200 wit h 50210 and 50211...
7305 “ “ Cari'ier with two each 440c and
45Sc................................................................
735.5 Fe(id Har Carriei' Hinge Pin
7355 “ “ “ “ “ Hushing
.........................
..........
7304 “ “ “ “ ■“ “ Set
Screw..............................................................
7304 Fca'd Har Carriei' Hinge Pin Set Screw' .. .
735.5 ‘‘ “ Hinge Pin...........................................
73()4 “ “ “ “ Set Screw
........................
7303 “ Dog, 10 teeth (18 teeth to the inch)
for .5i)431.......................................................
7301 k'eed Dog Screw.....................................................
“ Kcceniric.......................................................
- - “ “ Hody with 42727............................
7304 “ “ “ Si't Screw
73,57 “ “ Clam[»ing Wa.slier
........................
.................
7304 “ “ “ “ .Screw...
735.5 I’eed Fccentiic (adjustalile) com|ilelc. Nos.
217k, 7071, .5032,Sc, ,50213, .50401 and two
51001c
...........................................................
PARTS FOR М.АСИШЕ No. 105-20 9
NO. l>n.4TK NAME
50210 7355 Feed Eccentric Connection
.....................................
50217 7355 “ “ “ Bar with 59218
,59218 7355 “ “ “ “
449c 7361 “ “ “ “ Set Screw
50518 73,57 “ Lifting Eccentric with two 50150c...
,50510 _________ “ “ ** 59518 with 59220..
50'220 7357 “ “ “ Connection
................
,59221 7357 “ “ “ “ Bar with
.59218..............................................................
50218 7355 Feed Lifting Eccentric Connection Bar
Plug
.............................
....................................
•15Sc 7364 F’eed Lifting Fdccentric Connection Bar
42727 7364 Feed Lifting Eccentric Position Pin
Set Screw
,50L50c 7364 “ “ “ Set Screw
........................................................
........................
...................
,50328c 7364 “ Kcgulating Screw..........................................
50405 73,57 I.uoper with 590j and 59408
,50381 7357 “ Carrier with 50395c
.....................................
............................
50106 7357 “ “ Driver with two 1186e... ,
1LS6e 7357 “ “ “ Clamping Screw. . ,
207.1 7364 “ “ “ Timing Screw
.............
59225 7357 “ “ Hole Plug................................
.50220 7357 “ “ Shaft........................................
50227 7357 “ “ Crank with 1143e. ..
1143e 73,57 “ “ “ “ Clamping Screw
50407 7350 “ Needle Guard with 54707
51707 7350 “ “ “ Pin
...................
..............................
,500.j 73.57 “ “ “ Screw..........................
50305c 7357 ■* Set Screw..................................................
,50408 7357 “ 'Phread Guard......................................
500.1 7357 “ “ “ Screw..........................
50100 73.56 Needle Bar (hollow) with 906c
.50110 73,50 “ “ Bushing (lower)
.................................
........................
402c 7364 “ “ “ “ SetScrew....
42253 73,5(i “ “ “ (upper)........................
■162c 7364 “ “ “ “ SetScrew...
,50236 7356 “ “ Connecting Bracket with 175j
and 460c..........................................................
175.1 7304 Needle Bar Connecting Bracket Clamping
Screw
50237 7350 Needle Bar Connecting Link
..............................................................
.......
40247 73,50 “ “ “ “ Hinge Pin
(lower)
............................................................
208k 7301 Needle Bar Connecting Link Hinge Pin
(lower) Set Screw
...........................................
40247 7350 Needle Bar Connecting Link Hinge Pin
(upper)
..........................................................
1 SliSti -—3
...
10
NO. .
400c
59238
59007
59008
59240
1030c
*59503
141e
*59242
0 17k
59005
59000
128835
1299c
448c
42077
187.1
59245
59240
193,1 7357
,5,5,515
,59247
,59248
024 c
I’AR'I'S FOR MACHINE No. 1(0-20
,'KA'I’K
7304
(i]|)|ier) ¡^ot iSci'i'w........................................
7350
7305
Ni'(h11c liar L(!V(t wiHi 20Si', I ISc and
l():i(k;
.............
................................................
Ni'cdlo Bar Lever ('oniiecd iiie Hod willi
55510, 5!)2'I2, 50505, 12SS.Í5 and (avo
eacli 1 I Ik and 017k.......................................
Needle Bar Lever ('oiiiuaO iiifr Hod 59007
willi 59210 and 59005....................................
7357
Needle Bar Lever Conneetiiif' Hod Ball
Stud.................................................................
7357
Needle Bar Lever <’onneelin"' Hod Ball
¡Stud Mel Screw.............................................
730.5
Needle Bar Lever ('onneetliifi; Hod Cap
(_lower)..........................................................
7304
Needle Bar Lever Cionneetinji Hod Cap
(lower) Screw.................................................
7305
Needle, Bar Lever Conneetiiifi Hod Caj)
(np|ier)............................................................
7304
Neeiile Bar L(‘vei- Conneclinf; ILxl (iap
(upper) Screw.................................................
7350
Needle Bar Level' (amiieetinfi Hoil Eceen-
Iric willi I ISe, 1299c and (wo 59000... .
73,50
Needle Bal' Level' ('.oiineelint>: Hod Eeceii-
Iric Luliricaliiifi; Pad (wood)
73,50
73,50
Needle Bar Lever ('oiiiieciinn Hod Eccen-
I I'ic (>il ('lip
..................................................
Neeille Bai Lever ('onni'i't inn Hoil Ei'cen-
I i'ic Po.sil ion Screw......................................
7304
Neeiile Bai Level'ConnecIinn Hod Eceen-
li'ic Sel Screw.................................................
7350
Needle Bai Lever Conneclinn Hod Cnide
7301
Screw'
.............................................................
73.50
73,50
Needle Bai' Levi'r Cimneclinn Hod Cuide
Sliid
................................................................
Needle Bar Lever ('onneetinn Hod Cuide
Stud Brai'kel with 59215................................
Neeille Bar Lever Connectinn Hod Cnide
Stud Brai'kel Screw........................................
73,50
Needle Bar Lever Connect inn Hod Oil Pad
(liraided col Ion)
............................................
73,58
7358
(Lack)
...................
7304
eeille Bar Lever
(Lack) Sel Sci'ew.
.........................
B n .s li i n n
PARTS FOR MACHINE No. 105-20 11
NO. PLA™ name
59249 735S Needle Bar Lever Hinge Pin Bushing
(front)..............................................................
4G5c 7357 Needle Bar Lever Hinge Pin Bushing
(front) Set Screw
............................................
448c 7304 Needle Bar Lever Hinge Pin Set Screw...
59412 7358 “ Clamp w'ith 46478 and two 50505k
40478 7358 “ “ Thread Cuide
...........................
59321 7358 “ Guard....................................................
171f 7304 “ “ Screw
.505()5f 7358 “ Set Screw
.......................................
....................................................
59544 7358 Pressor Bar.................................................................
59252 7358 “ “ Bushing (lower)...............................
405e 7357 “ “ “ “ Set Screw----------
42253 7350 “ “ “ (upper)
..........................
4()5c 7357 “ “ “ “ Set Screw....
.59253 73.58 “ “ Lifter
51815 73.58 “ “ “ Roller and Stud
.......................
.................
89f 73,58 “ “ “ Hinge Screw..........................
.5013810 7304 “ “ “ Stop Screw
..........
595(15 73.58 “ “ Lifting Bracket with 391j,
1113c, 51810, 51811 and 51815
....................
391j 7358 Presser Bar Lifting Bracket Adjusting
Screw
.59500 73,')8 Presser Bar Lifting Bracket Cnide
..............................................................
........
0‘24c 7304 “ “ “ “ “ Set Screw'
1143c 73.57 “ “ “ “ SetScrew
59257 73,59 “ “ Spring
,59258 73.58 “ “ “ Block
......................
......................................
51810 73,58 “ “ “ Holler and Stnd
..........
.................
,59413 73()3 “ Foot Hinge Pin............................................
,59414
--------
“ “ Plato.................................................
59115
--------
“ “ Shank
...............................................
.59410 7i!03 Presser Fool, (hinged) complete, Nos. 59413
to 59415..........................................................
185ii 7304 Presser Foot Screw..................................................
1317i) 7304 Pressure Hegnlating Thninb Screw.........................
1547.1 7304 “ “ “ “ LockNut
59204 73,5,8 Slack Thread Controller
.......................................
9.5c 7358 “ “ “ Hinge Screw... .
.59205 73,58 “ “ “ Link
.......................
87c 7358 “ “ “ “ Hinge Screw
,59117 7301 “ “ Pull-off
............................................
,59418 7359 “ “ “ Eyelet
,59419 73.59 “ “ “ “ Plate with
03707
..............................................................
03707 7302 Slack Thread Pull-off Eyelet Plate Pin. . .
03707 7302 “ “ “ “ Position Pin.
....
12
No.
I'l.ATE
22S.I
59420
59207
5920«
5181 1
405(:
405<;
59121
•'Í8070
2102
5l570r
50:i2(ic
59529
59524
59527
59528 7202
2102
51570c
50220c
7202
59529
7204
1517k
59525
7202
59527
59528 7202
59270
59422
1422j
7202
7202
7201
7202
59422
59201
7202
452c
7202
59272
7202
59272
7202
190.)
7201
PAR'
rs FOR MACIIINF No. 105-20
7204
Sliick Thread Pull-oil Fyelct Screw
7257
7259
7259
7259
7258
“ “ “ SiTCW
“ “ Rc}i;ulator
“ “ “ Holder- with 405c
“ “ “ “ ('i-arik wit It
two 405c
.........................................................
Slack 'riii'ead HcKulator Iloldi'r (’rank
Holler and Si ud
7257
Slack Tlireaii liegrdator Holder (Tank
N,\ME
..............................
.......................................
.............................................
Set Screw........................................................
7257
Slack d'hread Kegidator Set Screw
7202
'reirsioii (under Hii-eadi Bracket
7259
7202
7202
“ “ “ “ Steady Pin
“ “ “ Hiac.........................
“ •* “ Regulating'I'liunih
Nut..................................................................
7202
'I'cnsion (under thread) Screw Stud
“ “ “ “ “ 5;i220c
willi 51570c....................................................
7202
Ten.siou (undra- thread) Sirring
7202
“ “ “ “ B u a li i n g
(liii'ge)............................................................
'I'cnsion (under Ihread) Sirring Bushing
(smrdll............................................................
7202
'rensiirn (upper Ihread) Disc...............................
7202
“ “ “ lirrguhding'rimn.b
Nut..................................................................
Tension (upptrr Ihi'cail) Screw Stud
“ “ “ “ 50220c
with 51570c....................................................
'I'cnsion (tiirjrer threail) Screw rStud Nut..
“ “ “ Spi-ing
“ “ “ “ Hushing
(large).............................................................
'rensioti (uirper (hrearl) Spi-ing Brtshing
(sttiidl)............................................................
'rirread (under) h'.yelct
......................................
“ “ “ Screw.............................
“ “ Nip|)(!r Bracket
“ “ “ “ 59422 with
9547, 59201, 59419 and two 02707
'rirread (under) Nipper Bracket Strrd
“ “ “ “ “ Set
tSci-ew............................................................
'I'hread (under) Nipjrer (Irrirle Plate
“ “ “ lieleitsing Brrrcket
ii ii U U ii
Sta-ew
..........................................................
....................
....................
........................
....................
.........................
..................
..................
.................
...............
.................
..................
PAR'I’S FOR MACHINE No. 105-20 13
NO. PI..\TE NAME
59274 7202 Thread (under) Nipper Releasing Stud. . .
,59275 7202 “ “ “ .Spring.......................
1422J 7204 “ “ “ “ Screw..........
9517 7259 “ “ “ “ Steady Pin
59270 7202 “ “ Protector.......................................
240f 7202 “ “ “ Set Scruw.....................
59277 7259 “ “ Take-up (left)
59278 7259 “ “ “ (right)
......................
.....................
190,r 7201 “ “ “ Screw......................
59280 7259 “ “ “ Staple
......................
59281 7259 “ “ “ “ Holder
with 904c
........................................................
59282 7359 Thread (under) Take-up Staple Holder
Collar will) 400c.............................................
400c 7304 'rirread (under) 'I'ake-up Staple Holder
Collar Set Screw
.............................................
59283 7359 'I’hread (under) Take-up Staple Holder
Collar Spring
..................................................
230k 7304 'I'hrearl (under) 'I'ake-up Staple Holder
Collar Spring Screw
.......................................
904c 7301 d'hrtrad (umler) 'I'ake-up Staple Set Screw
59424 7359 “ “ “ Stripper
.........................
59285 7359 “ “ “ “ Bracket
with 240f
........................................................
590iJ 7359 'I'hread (under) 'I'ake-up Stripjrer Bracket
Sc.rcw
.............................................................
207f 7304 'rhreatl (under) Take-up Stripper Screw. .
59425 7302 “ (upper) Check Spring
.........................
59420 7300 “ “ “ “ Bracket with
2273, 59427 and two 904c..............................
2273 7300 'rin-ead (upper) Check Spring Bracket Pin
’59427 7300 .............................. “ “ Stud
452c 7302 “ “ “ “ “ “
Set Screw........................................................
59428 7300 'I'hread (upper) Check Spring Regulating
Stud.................................................................
9(Hc 7361 'I'hread (upper) Check Spring Regulating
Stud Set Screw................................................'
904c 7361 'I'tiread (upper) Check Spring Stop Screw'
59429 7360 “ “ Eyelet (side of arm)..........
50014o 73(i4 “ “ “ “ “ “ Screw
59430 7360 “ “ Take-up
................................
9l)0o 7364 “ “ “ Set Screw......................
59431 7363 'I'hroat Plate for 59403
69If 7362 “ “ Screw
*15404
15405
------
'I'rade Mark............................................
--------
“ “ Rivet.................................................
...........................................
..............................................
...............
14
ACCESSORIES
\(l. NAMU
120H44 74(i() Oiler (copper {ilafed) with 120445.
120;i45 “ Spout, 0 ill. louji;
2()02() 72(i() Screw Orivei-(large)..................................
2l)4S5 72()ll “ (small)
12(1241 72ti() Tweezers (curved).....................................
4H22 72ti(i M'reiicli for 1547
2200:i 7:i(i(i “ “ 1575
.................................
........................
.........................................
......................................
KNEli LIh'4'KR PARTS
rT,.VTE NAME
NO.
7207 Rock Shaft Spring AdjustingDogwithdSOc
2770
7204 “ “ “ “ “ Set Screw
:S5t)C
7207 “ “ Stop Dog with 356c
2770
7204 “ “ “ “ Set Screw
;i5t)C
;!2i:s5
59512
------
7207 Rock Shaft complete, Nos. 2764, 0237,
0228, 7124, 10128, 10017, 32124 and
three 2770........................................................
Knee Lifter complete (power table) Nos.
211), 219.1, 22040, 32135 and 59509 to
59511
..............................................................
15
.............................
.......................
EDGE FOLDER
NO. l'L.\'nO N.AME
12021)5 7200 Kdge Folder (adjiislahle) on Shank.
M idi) 7201) “ “ Screw
......................................
KNEE LIFTER PARTS
.NO.
32040
fidso 1
50805
59509
2 In
59510
59511
219,1
7124
270 (
10128
10010
10017
2700
350c
2707
0337 7307
0338
350c 7301
35()c 730 1
32134
í»í;A'í'fd
----
Chain, 12?,t in. long, with 50801 and 50805
7301
7301
7301
7301
7301
7301
730 1
7iíl)7
7307
7lit)7
7307
---
7307
7301
7307
730 1
7307
7iil')7
“ Hook (Ijirgc)
“ “ (small)
Lifting T.cvcr
“ “ Spring
" “ Sti)])...................................
Hock Shaft
“ Hanger (hack 1 wit ii two wood
screws 1 in. No. 10 ..
Hock Shaft Hanger (front) with two wood
screws 1 ill. No. 10...
Hock Shaft Knee ¡\rni .
--
liock Sliaft Kiu'e .\rm (Munph'ti*, Nos.
■*^7(i(i, 27<)7 and Kifl K)..
liock .Siiaif Isiua; .\njj Hub uilh dobc, . .
“ “ “ “ Sol Screw. . . .
“ “ Plate willi 350c..............................
“ Spring...............................................
NAME
........................
.............................................
..................
“ Hinge Screw.........................
.....................................................
“ Screw........................
.......................
“ “ Set Screw............................
“ Lifting Bracket willi two 350c
“ “ “ “ Set Screw....
Hook
...............
“ “ S(*l. So’cw
MACHINE BASE
NO. 1‘L.ATE NAME
59295 7207 Machine Base with lOOn, 36006, 59296 and
59296 7;i00 Machine Ba.se Cover
20000 7200 “ “ “ Friction Washer. . . .
lOOi) 7204 “ “ “ Hinge, Screw
840e 7204 “ “ Screw
59297 7300 “ Cnsliion (felt)
four each 840e, 59297 and wood screws
1>2 in. No. 14.................................................
...........................
.......
...........................
............................................
THREAD UNWINDER
FOR THREE SPOOLS
NO. !’1..\TK NAME
225259 20778 Spool Rest (for one spool) with 201l)18c...
225257 20778 “ “ (for two s|)ools) with 201018e'..
150203 --------------- “ “ Cushion (felt )................................
225388 20778 “ “ Bod...................................................
200383c 7304 “ “ “ Set Screw
201018c 7301 “ “ Set Screw.......................................
202490 20778 “ Stand with 200383c
225391 20778 d’hread Guide..........................................................
201090,1 7301 “ “ Lock Not
225320 7301 “ “ Position Cup
225324 20778 “ “ Hod with 208e and 225322
20He 7304 “ “ “ Screw.............................
225322 7301 “ “ “ Washer
*150057
150058 20778 “ “ 150057 with 15()059.. .
*150059
150000 20778 “ “ “ Arm with 104j
------
“ Sc|>arator...........................................................
----------------
“ “ Bracket
and 9525..........................................................
....................................
....................................
...............................
................................
..........................
.............................
16 TllUr^AD UNWINDER
NO. IM.ATK NA.MK
164.1 7iit)4 Thread Stiparator Hra(4vet Arm (4am})iiig
Sci'(;\v.............................................................
651^5 7361 TlinauJ S(iparat(>r Bracket Arm (’lam|)ing
ScT(iw Waslu'r
Kil.i 7364 44irtia(l Separator Hi'acki't Screw
...............................................
.........................
6625 7361 “ “ “ Washer
ir)0(Mil
-----------
4'Iiread Separaloi’ compl(4(^, Nos. 161.i,
6525, 15005S and 150060
15017S 2077S Tlircad Unwinder comj)lete, No.s. 150061,
20HÌ66.I, 202460, 225257, 225256, 225324,
225321), 2253<S8 and three ea<4i 150203,
..................................
225il6l and wood scn;ws Ja ■
27736 7i6)(i 44ii'<'ad (’om^ (wood) for largì* cones . . .
225:160 736t) “ “ Holder, for inverted cones .
NoTK. Nos. 27736 and 225:160 are used witli,
hut not im4iided in 150178.
Genuine Singer Needles should be used
in Singer Machines.
These Needles and their Containers
Company's Trade Mark “SIMANCO.” 1
are marked with the
Needles in Containers marked
**For Singer Machines*^
are not Singer made needles.
-i {tìì-tó*
17
NUMERICAL LIST OF PARTS
NO, IT,ATE NAME
211) 7H()4 Lifting Lever Hinge Screw for 59512. . ..
87c 7558 ShickThreadControllerLinkHingeScrew
89e 7H58 I’res.ser Bar Lifter Hinge Screw
95o 7558 Slack Thread Controller Hinge Screw. . .
lOOn 75()4 Macliine Base Cover Hinge Screw for
592<I5...........................................................
LHk 7ii(>4 Needle Bar Lever Connecting Rod Cap
(lower) Screw for 59C07
Kilj 7:i()4 Thread Unwinder Thread Separator
Bracket ,\rin Clamping Screw for
15001)0.........................................................
lOlj 7504 4'hread Unwinder Thread Separator
Bracket Screw for 150001
171e 7504 Needle Guard Screw
175.1 7504 “ Bar Connecting Bracket Clamp
ing Screw for 59250
17tij 7504 heed Dog SiT-ew
I Son 7504 Presser Loot Screw................................................
187j 7501 Needle Bar Lever Connecting Rod Guide
Screw.............................................................
190j 7501 Thread (under) Nipper Releasing Bracket
SiT'Cw...........................................................
190j 7501 'riiread (under) Take-u]) Screw
195.1 7557 Needle Bar Lever Connecting Rod Guido
Stud Bracket Screw.......................................
195.) 7557 Slack Thread PuU-off Screw.................................
207j 7504 Looper Carrier Driver Timing Screw... .
207k 7504 Thread (uiuicr) 'Pake-up Stripper Screw,,
208k 75()1 Needle Bar Connecting lank Hinge Pin
(lower) Set Screw for 59258.........................
208k 7504 'Diread Unwinder Thread Guide Rod
Screw for 225524
217e 7504 Feed Eccentric Clamping Washer Screw
for 59495.......................................................
219j 7504 Lifting Lever Stop Screw for 59512
228.1 7504 Slack Thread Pull-ofT Eyelet Screw
250k 7)i04 'I’liread (under) Take-up Staple Holder
Collar S])rlng Screw
240k 7502 Thread (under) Protector Set Screw for
59285
550c 7501 Rock Shaft Knee Arm Hub Set Screw for
2700.................................................................
550c 7501 Rock Shaft Knee Plate Set Screw for 2707
..............................................
....................................................
............................................................
...........................
..............................
............................
......................................
..............................
..........................................
.......................
....................
.....................................
IS химккгслг. MST OF PAin'S
NO.
NAMIO
liock Sluift Lifting Hnu'knt Hook S(4
S(Tt‘\v ft)r 0447
7otH
liock »Sli.-ifl Lifting lir;t('kot »SiO Sercu'
.............................................
for 0447 ........................................................
7M(i 1
Hock Sluifl Spring Adjusting Dog Srf
Screw for 4770
liock Shafl Stop Dog Set Scr<;w for 4770
7.)l)4
7;k7S
Lressf'r Bar Lifting Bracket -Adjusting
...........................................
421c 7304 Bidanee W iiee! Set Sertiw for 7>040S. . .
418c 7:504 ,\jiii Rotary Shaft Ru.shing (front) Set
S(TCw.............................................................
4 bSc 74(il Needle Ikir Levt'r ('oim(H‘ting Hod lAieen-
ti i(‘ S(4 Screw for 7)0t)07> . .
4!8c 7:>til
Xi'edlc Raj' Levi'j- Hinge I’in Set Screw
for 592:58.................................................
449c 7:;oi Feed 17cc('iil I’ie (’oniUMit ion Bar S(4 Sennv
4Г)12г 74t)2
for 40410
d im“,-id (under,! Nipper Bracket Stud SiO
..................................................
Screw..........................................................
452c 7:502
d'hread (npp(‘r) (’lu'ck Spring l^i’aeket
Si ud S{‘l Serew.......................................
4Г)7о 7;)itl Feed Rjij- ('ju-riei- Hinge Pill Rushing Set
Sci'ew
4.5SC 7:501
...........................................................
¡’'('cd Bar (’arri(‘r Hinge Bin Set Serew
for 7)0400..............................
loSo 74(il
feed Lifting !'a-c(M)trie (’onneetiou Bar
Set Serew for r)‘0410.............................
itiDi' 7:;oi
Needle Bar ('onmaOing Link Hingf* Bin
(uj)[)(‘) ) SfM Serciw for 40440
Ititk- 7:5til
'riiiT'ad liindin) d'ak('-\ip Staple Holder
( ollar Set SeiT^v for 404S4
4ti2c 7:501
4()Ги; 7:)Г)7
4Г)5(' 74Г)7
4()Г)0 71)Г>7
Itine 7:557
4()Г)0 74Г)7
71)7)7
Г>‘М),| 747)7
7>‘.M1d 747)0
ti21c 7:501
N'eeilk' Bar Bushing (lowt'V) Set Serew...
74t)l
" “ ■' (uppc'r) Set SiTcw. .
“ L(‘V(u’ Hing(‘ ihn Busliing
(ironi i Set Sri'f'W
...............
Pi'csser Rar Rnsliiug (lower) Set Screw. .
“ “ “ (upiier) Set Screw. .
Slack d'hiead lii'gnlator Holder ('rank
Set Serew for 40408
..............
Slack Thi'cad Regulator Set Screw for
.a92()7
.................................
Looi>er N('cdl(‘ (luard Screw .
“ 'riiread (luard Sei'cw for 591(15. .
Thread (uiuier) 'I’ake-up Stripper Rracket
Sci'cw
....................................
Needle Rai- Le\ci' Hinge Pin Rii.sliing
..................
NUMERICAL LIST OF PARTS 19
NO. I'I,\TK NAME
t)21o 7S61 Presser Rar lafting Rracket Guide Set
Screw
............................................................
()17io 7:504 Needle 15ar Lever Connecting Rod Cap
(upper) Screw for 59007...............................
OOlr 7:503 Throat Plate Screw
810e 7304 Machine Rase Screw for 59295
................................................
..............................
SS2c 7304 Keetl Rar Hinge Pin Set Screw for 59209
90 !i: 7:501 'I’hread (under) Take-up Stai)le Set Screw
for 59281 ......................................................
üO lc 7:501 Thread (upper) Check Spring Regulating
Stud Set Screw for 59426
.............................
90 lo 7301 Thread (upper) Check Spring Stop Screw
90(io 7304 “ “ Take-up Set Screw for
59409
............................................................
1030c 7:557 Needle Rar Lever Connecting Rod Rail
Stud Set Screw for 59238
.............................
114:5k 7357 Looper Carrier Shaft Crank Clamping
Screw for 59227
...........................................
1 l l:ic 7357 Presser Rar Lifting Rracket Set Screw for
59505
............................................................
1119c 7:504 Cloth Plate Screw
1180k 7:157 Loo])er Carrier Driver t.damping Screw
..................................................
for 5940()......................................................
12S5c 7:504 Arm Rotary Shaft Rushing (back) Set
Screw
............................................................
1285c 73t)4 Arm Rotary Shaft Rushing (intermediate)
Set Screw
......................................................
1299c 7:550 Needle Rar Lever Connecting Rod Eccen
tric Position Screw for 59005
.......................
i:il7o 7304 Pressure Regulating'l'huiub Screw...........................
135 li- 7304 Ralancc Wheel Position Screw for 59208
142:5,1 7:504 .Arm Side Cover Screw
......................................
112:5,1 7:5t)4 'I’liread (under) Eyelet Screw.............................
142:5.1 7:504 “ “ Ni])iier Sju'ing Screw. ,. .
1 li:Sj) 7300 Edge Folder Screw
......................
.........................
1547,1 7:5t)4 Prc'ssure Regulating 'Г1шшЬ Serew Loek
Nut................................................................
1517k 7:504 4'ension (upper thread) Screw Stud Nut. .
2102 7302 “ (under thread) Disc...........................
21t)2 7:502 “ (upper thread) Disc...........................
227:5 7:500 “ (up|)er) Cheek Spring RrmLet
Pin for 59420
................................................
2701 7:507 Uo(4-i Shaft Hanger (back) with two wood
sci'i'ws 1 in. No. 10, for 32135
.....................
27ti0 7:5t)7 Rock Shaft Knee Arm Hub with 350o, for
10047............................................................
20
NO. l'l,.\TE
2707
2770
2770 7307
4822
0337 7307
0338 7307
7071 7357
7124
9525
9525
95 17
*15101
15405
10128
10040
10047
22003 7300
20020
20485 7300
27739 7300
32040
32134
32135
30000
38070
40247 7350
40247 7350
42077 7350
NUIMI'MÍICAL LIS'r OK РЛН'ГЯ
NAME
Rock Sliaff Knee I'lafe wi(li У5(к', for
73f)7
10()17...........................................................
7307
Rock Shalt Spring Adjusting Dog with
:?5t)<:, for :S2i:i5
.........................................
Rock Slialt Stop Dog wit h 35lic, for 021Ü5
7300
Wreiudi for 1547 (Accessories)
Rock Shaft Lifting Bracket witli two
Ohtic, for :S2i;55
..........................................
Rock Shaft Lifting Bracket Hook for
02135............................................................
Kc(al Decentric ('lamping Washer for
59405............................................................
7307
Rock Shaft for 32135
73t)l
Tincad rnwindt'r 'riireaii Separator
.......................................
Bra(4ud Arni Clamping Screw Washer
for 15011Ш).................................................
7301
'I'liread Lnwinder Thread Se[)arator
Bmcki't Screw Washer for 150l)lil
7359
Threa<l (under) Nipjier Spring Steady
- - _
Ti'ade Mark
“ “ Rivet
7307
Rock Shaft Hanger (froid) with two wood
Bin for 59423
...............................................
......................................................
..............................................
scr(!ws 1 in. No. It), for 32135
7307
Rock Shaft Knee .Ann for 1111)47
Rock Shaft Knee .\rm complete for 32135,
Nos. 27(>(), 27117 and llililtl
\\ remdi for 1575 (Accessories) .
7300
Screw Driver (large) .Acce.ssories
“ “ (small) -Accessories
Thread Lnwinder 'I'hread Cone (wood)
—
7307
7307
for large cones, for 15017S
('hain, 12'hi in. long, with 5t)8(il and
5tiStl5, for 59512
Rock Shafi Spring for 32135
.........................................
...........................
Rock Shaft complete for 59512, Nos.
27(14, (1337, (1338, 7124, 1(1128, 1(11147,
7300
32134 and three 2770
Machine Base Covei' Kriction Washer for
...................................
59295............................................................
7359
'I'ension (under thread) Bracket Steady
Bin................................................................
Ni'edle Bar (’onnecting Link Hinge Bin
(lower)..........................................................
Needle Bar Connecting Link Hinge Bin
(upper)..........................................................
Neeille Bar Lever Connecting Rod (Inidc
.......................
..............
....................
.................
......................
.....................
...................
.....................
..........................
NUMERICAI) LIST OF BARTS
NO. PLATE NAME
42253 7350 Bresser Bar Bushing (upper)
42253 7350 Needle Bar Bushing (upper)
................................
.................................
21
42727 7304 Feed Lifting Kccentric Position Bin for
59494
............................................................
40478 7358 Needle Clamp Thread Guide for 59412. .
50014c 7304 d'hread (upper) Eyelet (side of arm)
Screw
............................................................
50138E 7364 Bresser Bar Lifter Stop Screw
...............................
50150c 7304 Feed Lifting Eccentrie Set Screw for
59518............................................................
50320c 7362 4'cnsion (under thread) Screw Stud for
59539............................................................
50320c 7302 'rension (upper thread) Screw Stud for
59539............................................................
50328c 7304 Feed Regulating Screw for 59495
..........................
50395c 7357 Looper Set Screw for 59381...................................
50505e 7358 Needle Set Screw for 59412...................................
51001c 7304 Feeil Eccentric Body Set Screw for 59495
51570c 7302 'I'ension (under t hread) Regulating'riuunb
Nut for 59539
...............................................
51570c 7302 Tension (upper! bread) RegulatingThurnb
Nut for 59539
...............................................
51810 7358 Bresser Bar Spring Roller and Stud for
59505
............................................................
51811 7358 Slack 'I'liread Regulator Holder Crank
Roller und St ud for 59505
...........................
51815 7358 Bresser Bar lafter Roller and Stud for
59505
............................................................
52045 7355 Ann Rotary Shaft Bushing (back) Back
ing (cotton) for 59523...................................
52045 7355 Arm Rotary Shaft Bushing (front) Back
ing (cotton) for 595'24
..................................
52045 7355 Arm Rotary Shaft Bushing (intermediate)
Backing (cotton) for 59525
54707 7350 Looper Needle Guard Bin for 59407
..........................
....................
55515 7350 Needle Bar Lever Connecting Rod Oil
Bad (braided cotton) for 59007.....................
50804 7301 Chain Hook (large) for 32040
.........................
50805 7301 “ “ (small) for 32040............................
57234 7355 Feed Bar Carrier Hinge Bin..................................
57235 7355 “ “ “ “ “ Bushing
...........
59207 7305 Arm Side Cover....................................................
59208 7305 Balance Wheel, 2% in. diam., with 424c
and 1354c
......................................................
59209 7305 Feed Bar with two each 458c and 882c,
for 59440.......................................................
■
NUiMl''UTCAL LIST OK PAIH'S
NUMKRICAL LIST OK PARTS
23
Г1.ЛТЕ
NO.
59210
7365
,59211
73,55
*,59213
59216 73,55
.59217 7355
59218 7355
.59218 73,5.5
59220
73.57
59221
7357
5922,5 73,57
59226
73,57
59227 7357
59236
73.56
7356 .Needle Bar Connecting I.ink
,59237
7.356
59238
.59210
7o57
*.59212
,59215
59219
.59217
7365
73.56
73,56
73.58
,59218 73,58
59219
TiifiS Needle Bar Lever Hinge Pin Bii.shing
592.52
73.58 Hi'e.sser Bar Bushing (lower)
,59253 73,58
,592,57
73.59
,592,58
73,58
,59261
73,58
.5926,5
7358 “ “ “ Link
,59267
7359 “ “ Regulator llolilei-with 46.5c
,59268 73,59
.59270 7362
59272
7362 “ “ N i¡)per (! uide Plate.............................
,59273
7362
NAME
Kccd Bar Carriia- witli Iwo each 449c ami
4,58c, for 594 10
..........................................
Kced Bar Hinge Pin for ,59140......................
“ rio ior Г)9195.............................................
“ “ (k)uticc'(ion
“ “ “ Bar with 59218
“ “ “ “ J’lug for
...................................................
.59217...........................................................
Kccd Lifting IL'centric Connection Bar
I'hig for 59221.............................................
I'ccd lafting Kcccntric Connection for
59519
............................................................
l-’ocd Kc(‘(Mi1ric ('omu4.‘tion Bar
with Г)9218..................................................
Loop(a-Carrier Hole Plug..............................
“ “ Shaft.......................................................
“ “ “ ('rank wit li 11 13e . .
Needle Bar Connecting Bracket with 175.Г
and 46l)c.......................................................
........................
“ “ Level- with 208k, 41,Sc and
1036c..............................................................
Neodlo Bill' 1д)\Ч‘Г (-’uiincctiiig Hod Ball
Stud tor 59t>0S
...........................................
Xeudlu Bar Bovoi’ (’onneoting Uoil (’ap
(ui>perj for о1КИ)7........................................
Needle Bar Lever Comu'cting Rod Cuide
Sind for .59216............................................
X'oedlc Bur L(‘\'ci' ('onni'cl inj^ Hod (luido
Stud Bracket ivithdii‘^15...........................
Needle Bar Bewr llii^t* Bin...........................
“ “ “ *' “ в u s h i n g
(hack)...........................................................
(front)...........................................................
.......................
" “ l-ifler.....................................................
“ Spi'inji
.....................................................
“ “ " Block..................................................
Slack ddiread ('oriiroller................................
.....................................................
“ “ “ “ Crank wilh
two 46.5c
Thread (under) klyidct
......................................................
...................................
“ “ “ H(‘leasiiu^‘Bi'acket
PLATE NAME
NO.
7302 Thread (under) Nipper Releasing Stud.. .
59274
7392 “ “ “ Spring...........................
59275
7I5()2 “ “ Protector
59279
7359 “ “ Take-up (left)
59277
7359 “ “ “ (right).................
59278
7359 “ “ “ Staple
59280
73f,() “ “ “ “ Holder
59281
with 904o
......................................................
..............................
...................
.................
59282 7359 Thread (under) Take-up Staple Holder
Collar with 460c............................................
59283 7359 Thread (under) Take-up Staple Holder
Collar Spring.................................................
59285 7359 'I'liread (under) Take-up Stripper Bracket
with 240e.......................................................
59292 7361 Cloth Plate Steady Pin for 59401..........................
59295 7397 Machine Base with lOOn, 36009, 59296
and four each 840e, 59297 and wood
screws 1 Vi in. No. 14
59296 7390 Machine Base Cover for 59295
592'.)7 7390 “ Cushion (felt) for 59295
...................................
............................
..........................
5i)301 73()2 Thread (under) Nipper Bracket Stud for
59423.............................................................
.5t)307 7395 Cloth Plate Slide (left) for 59402..........................
593t)8 7395 “ “ “ (right) for 59402
...................
59321 7358 Needle Guard........................................................
5<)3S1 7357 Looper Carrier with 5039.5c.................................
*593t)9 — - Arm, upper and lower (solid)............................
5i)101 7il97 Cloth Plate with 59292, fur 59102
.......................
59102 — - Cloth Plate coin])letc. Nos. 59307, 59308
and 59401......................................................
5;)403 7363 Kced Dog, 19 teeth (18 teeth to the iindi)
for ,59131......................................................
59105
.56106
59107
,59108
.59409
59110
.56112
,59113
.56114
.56115
,56116
Looper with 59t).i and ,59408
7357
73.57
7356
7357
7356
7356
73.58
7363
“ (.kirrier Driver with two 1186e. . .
“ Needle Guard with 54707
“ 4'hread Guard for 59405
Needle Bar (hollow) with 906c
“ Bushing (lower)
“ Clamp with 46478 and two 50505k.
Presser Koot Hing(! Pin for 59416
“ “ Plate for 59416..............................
“ “ Shank for 59416............................
Presser Koot (hinged) complete. Nos.
7393
59413 to 59415
............................................
..........................
.........................
...........................
........................
.............................
...................
.59117 7391 Slack'riiread Pull-off.............................................
,59118 73,59 “ “ “ Kyelet..............................
21 NUMliRICAL LIST OK I'ARTS
NUMERICAL LIST OF PARTS 25
NO. 1>L.\T10 NAME
f)iltl!) 7359 Slack Thread Rull-olT Eyelet Plate with
()37()7, for 59123
.........................................
59121) 7359 Slack'rhrea<l Regulator.........................................
59121 7302 d'eu.sioii (under thread) Hiacket...........................
5!)122 7302 'I'hread (under) N ippcr Bracket for 59423
59423
59424 7359 'Phread (under)'I'ake-up Si ripper
-----
“ “ “ “ 59422 with
9547, 59301, 59419 and two 03707
.........................
..............
59425 7302 “ (upper) (.dier;k Spring...................
59420 7300 “ “ “ “ Bracket
with 2273, 59427 and two 904c....................
’•5i)427 731)0 Thread (upper) Check Spring Bracket
Stuil for 59120
..............................................
5942S 7300 Tliread (up[)ei') ('/icck .Spring liegnl.iiing
Stud...............................................................
59429 7300 'Phreiid (\ii)))er) Eyelet (.side of :irm) ....
,59430 7300 “ “ Take-up
..............................
59431 73t)3 Throat Plate for 59403..........................................
5!I440
------
Keed Bar 5920!) wit ii 59210 and 59211...
5!)f91 7305 Ann Rotary .Sliaft.................................................
*594!)4
--------
l’'eed Ecceulric Body with 42727, for
59495
............................................................
59195 7355 h'eeil Ifccentric (ailjuslahle) couiplete.
Nos. 217e, 7071, .50,3280, .59213, ,594!)4
and I wo ,51001c...........................................
*59503 7305 Needle Bai' I.evi'r ('onnialiiig Rod Cap
(lower) for 59007..........................................
5!)505 73.58 I’lcs.ser Bar lafling Bnicket with 391,1,
1143c, 5IS10, ,51811 and 5ISI5...................
59500 73,58 Pressi-r Bar lafling Bracket (unde
5!)509 7301 lafling I.ei i'r for .59.512
......................................
59.510 7301 “ “ Spring for ,59512
59511 7301 " “ Slop for ,59512
59512
------
Knee lafler coinplele (powaa'talilel, Nos.
.......................
.........................
............................
211), 219,1, 320 10, 32135, .59.509 lo 59511
59518 7357 Keed lafling Ecceniric with two 501.50c,
.59519
for 59,519
------
h'eeil lafling Eccentric .59518 with 59220
.....................................................
59523 7355 .Arm Rotary Shaft Bushing (hack) with
52045. . .'
......................................................
.59524 7355 Arm Rotary .Shaft Biisiiing (fronl; with
,52045...........................................................
.59,52,5 7355 .Ann Rotary Shaft Bushing (intennediate)
with ,5201.5..................................................
595(54 7(502 'Pension (under thread) .Spi'ing.............................
,5i).535 7(502 “ (upper thread) .Spring
.......................
NO. IM,.\TE N.AME
59537 7302 Tension (under thread) Spring Bushing
(large)............................................................
.59537 7302 Tension (upper thread) Spring Bushing
(large)............................................................
.59.538 7302 Tension (under thread) Spring Bu-shing
(small)...........................................................
5!)538 7302 Tension (upper thread) Spring Bushing
(small)...........................................................
59,539
--------
Tension (under thread) Screw Stud 50320c
with 51570c...................................................
59539 ---------Tension (upper thread) Screw Stud 50326c
with 51570c...................................................
59544 7358 Presser Bar................................................................
.59005 73,50 Needle Bar I^ever Connecting Rod Eccen
tric with 448c, 1299c and two 59600,
for 59608.......................................................
.59000 7350 Needle Bar Lever Connecting Rod Eccen
tric Lubricating Pad (wood) for 59605
,50007 7365 Needle Bar Lever Connecting Rod with
55515, 59242, 59503, 12883,5 and two
each 141e and 647e, for 59608
....................
59608 --------- Needle Bar Lever Connecting Rod 59607
with 59240 and 59605
..................................
63767 7362 Slack 'Phread Pull-off Eyelet Plate Pin
for 59419.......................................................
63767 7362 Slack 'Phread Pidl-off Eyelet Position Pin
for 59423.......................................................
120265 7360 Edge Kohler (adjustable) on Shank
.........................
120341 7306 'Pweezers (curved) Accessories............................
120344 7366 Oiler (copper plated) with 120345 (Accesi-
sories)............................................................
P20(i45 7366 Oiler Spout, 5 in. long, for 120344 (/Acces
sories) ...........................................................
128835 7356 Needle Bar Lever Connecting Rod Eccen
*1.50057
------
tric Oil Cup for 59607
Thread Pinwinder 'Phread Sejiarator for
150058
..........................................................
..................................
1,500,58 20778 'Phread UnwinderThreadSeparator 150057
*1.50059
with L50059, for 150061
--------
Thread Unwinder Thread Separator
Bracket for 150058
..............................
.......................................
1.50000 20778 Thread Unwinder Thread Separator
Bracket Arm with 164j and 9.525, for
150001
..........................................................
1.50001
-------
d'hread Unwinder Thread Separator coin-
Ijlete for 150178, Nos. 164.1,9525,150058
iiiul 150000...................................................
18(i8li—1
2<> NUMKUK^AL T/ISr OK KAU'rS
NO. IM.ATI': namk
ir)0178 ‘2077S 'riiremi Unwiiiiler ('oini)leto, for thnn;
■spool,s, Nos. loOimi, 20Hii)().p 20241)0,
225257, 225251), 225521, 225;i2(i, 2255S8
aiul Un(’c t':u4i 150205, 225501 iiiid
wood s(‘-n‘ws ^ 8 ill. No. 12........................
150205
----
Tlii-(‘ad Unwinder Spool Rest (5ishion
(felt) for 150178
...........................................
200585(^ 750-1 'i'lirend Unwinder Spool Rest Rod S(*|.
Scjew for 202190
.........................................
201018c 7504 4’hreud Unwinder Spool Rest Set Serew
for 225257 end 225250
................................
201000J 7501 Thread Unwinder ddiread (inide lauT
Nut for 150178.............................................
202-400 20778 44)re;id Unwinder vSpool Stand with
200585(’, for 150178....................................
225257 20778 Threatl Unwinder Spool Rest (for two
spools) with 201018c, for 150178
225250 20778 4’liread Unwinder Spool R(‘sl (for one
• si»ool) with 201018c, for 150178
225522 7501 Thread Unwinder ddiread (hiide Rotl
Washer for 225524.......................................
225:124 20778 'I'hread Unwinder 'I’hi'ead (!uide Hod
with 208k and 225522, for 150178 ...
225520 7501 4'hn‘ad Unwinder 4'hread (luidi' Position
(hip for 150178..........................................
225588 20778 'Phniad Unwimha' Sjiool Rest liod for
150178
.........................................................
225500 7500 Thiead Unwinder 'Phread Comi lloldt'r,
for inverted cones, for 150178
225501 20778 'Phri'ad (hiwi rider'I'hread (iiiiile for ! 50178
.....................
.............
................
Genuine Singer Needles should be used
in Singer Machines.
These Needles and their Containers
Company’s Trade Mark “SIMANCO.” 1
are marked with the
Needles in Containers marked
^^For Singer Machines”
are not Singer made needles.
57234 59211 59217 '^’5'2'045^ 57235.
Mp.
59216
59218
•1 ;<«>',.
PLATE 7356-FULL SIZE
PLATE 7357t#ULL SIZE
59221
1186 1143 193 1036 465 7071
H
59220
PLATE 7358-FULL SIZE
PLATE 7359-FULL SIZE
59544
59247
59258 46478 5^52
I ■ Y4 W 50505
M
PLATE 7360-FULL SIZE
PLATE 7361-FULL SIZE
59429 59430 1443 59427 59426
59417
225325 59509
PLATE 7362-FTJLL SIZE*
";;-1
PLATE 7363-FTILL SIZE
59273
515 70
59421
59416
59431
'rM
59413
59403
691
'«IS*
if
a
PLATE 7364-FULL SIZE
1317 84D 21 50328 35b
647 1149 424 1354 141
CJ
59491
PLATE 7365-ONE-HALF SIZE
59208
59242
59307
59607
164
219
Iff
185
217
T
207
1
1
882 460
m
462
u
42727 1547
s
50150
m
176 51061 201018 100
1^3 208
¥
236
228
¥
458 624
M
457
m
y
50014
u
»
59503
59308
0
PLATE 7366-ONE-HALF SIZE
PLATE 7367-ONE-FOTJETH SIZE
26026
120341 225390
120344
2113°!
Z770 n '6337 71^4 ’V
16W6
59295
'S, I
2767
59401
PLATE 20778-ONE-SIXTH SIZE
150178
Loading...