Sinclair SCMI-01 User Manual

SCMI-01

USBCommunicator

USER'S MANUAL

EN

1. Introduction

USBCommunicator allows easier and faster setting of SCMI-01 and is available on mini CD or on our
website

www.sinclair-solutions.com

. USBC software can also display current setting of SCMI-01

module.

2. Preparation

Mini USB cable is needed for communication between computer and SCMI-01 module. This cable is
not included in standard package.

Fig 1: Mini USB cable Fig 2: Front panel of module

Connect the SCMI-01 module with computer using mini USB cable (Fig 1). Display of module will turn
on after successful connection.

3. SCMI-01 setting via USBCommunicator

Application bookmark

Here you can find the information about this software (“About”), select the language (“Language”)
and you can also close whole application (“Close”).

Fig 3: „Application“ bookmark

Device bookmark

This option shows „Supported devices” interface. To set SCMI-01 module, choose SCMI Sinclair driver
option. USBC software will automatically detect SCMI-01 device after you connect it to computer.

Fig 4: „Device“ bookmark

The setting options in USBC software are the same as options in SCMI-01 module itself. You can find
detailed information about each feature in user manual for SCMI-01 module.

Fig 5: SCMI Sinclair driver interface

Main menu Submenu/Option Range Default Note:
Target value

Setting of desired temperature; this menu is not accessible in the slave
mode.

-10 to +60 +10,0°C p. 7

Function Operated

Slave unit mode. The module is controlled by an external voltage 0­10V.

Operated p. 8

Reg. P

Autonomous pressure (evaporation temperature) control mode p. 9

Reg. T*

Autonomous temperature control mode for cooling p. 10

Reg. T+

Autonomous temperature control mode for heating

Defrost Mode Off

Defrosting of indoor unit evaporator is not in use Off p. 11

External

Defrosting with external support (heating cable etc.)

Reverse

Defrosting by switching from cooling to heating
mode.

Period

Setting the minimum time period between defrosting
cycles

0.1 to 99.9 1 hour p. 12

Length

Setting the maximum duration of defrosting 1.0 to 60.0 10 min

Start

Setting the temperature to start defrosting -20 to +5,0 -5,0°C p. 13

Stop

Setting the temperature to stop defrosting +3 to +25.0 +7,0°C

Outputs Relay 1 Function ON/OFF

Relay is controlled by On/Off input. On/Off p. 14

Compres.

Relay is controlled according to the
compressor

Defrost

Relay is controlled according to the
operation (Heat/Cool)

Error

Relay is controlled according to the
error state

Heat/Cool

Relay is controlled according to the
operation (Heat/Cool)

Limiting

Relay to limit the long lasting
compressor load.

Logic Direct

Relay switches with direct logic Direct

Inverse

Relay switches with inverse logic

Relay 2 Function

This setting is the same as setting the Relay 1 Compres.

Logic

This setting is the same as setting the Relay 1 Direct

Relay 3 Function

This setting is the same as setting the Relay 1 Error

Logic

This setting is the same as setting the Relay 1 Direct

DC Vent Fixed

Setting the speed and mode (Co, Fa, On) of the
indoor fan

Off p. 15

Auto 1

Fan speed according to compressor speed 1:1

Auto 2

Fan speed of 60-200% of compressor speed

Off

Output not used

Reg.cons Time con

Setting the time constant of the module. 10 to 999 30 sec. p. 16

Prop.con

Setting the proportional constant of the module. 0 to 999 35

Int.cons

Setting the integral constant of the module. 0 to 999 0

Der.cons

Setting the derivative constant of the module. 0 to 999 60

Display Backlight

Setting the LCD backlight. 1 to 16 8 p. 17

Contrast

Setting the LCD contrast. 1 to 16 8

Time gap

Setting the time period of the operator inactivity 10 to 999 60

Language

Setting the language version CZ / EN EN p. 18

Password

Enter the password before setting the module. After logging in, you can perform
setting for about 30 minutes. Without knowing the password, you can only adjust the
contrast and backlight brightness of the display.

201201 p. 6

Tab 1: Summary of the module settings

After setting is done, click on “Write” button to save all parameters in module memory.

All saved parameters can be displayed by clicking “Read” button.

4. Language update of SCMI-01 module

Click on “globe” icon in SCMI Sinclair driver interface (as shown in fig 5). In the dialog window
you need to open “languages” folder located in downloaded files/on mini CD and choose desired
language set (XXX.RAW file). Each language set consists of two languages – English and the chosen
one (DE, PL, CZ, HR, HU).

5. Password

You can change or deactivate password via USBC software.

NOTE CONCERNING PROTECTION OF
ENVIRONMENT

This product must not be disposed of via normal household waste after its service life, but must be
taken to a collection station for the recycling of electrical and electronic devices. The symbol on the
product, the operating instructions or the packaging indicate such disposal procedures. The materials
are recyclable in accordance with their respective symbols. By means of re-use, material recycling or
any other form of recycling old appliances you are making an important contribution to the protection
of our environment. Please ask your local council where your nearest disposal station is located.

In case of quality problem or other please contact your local supplier or authorized service center.

Emergency number: 112

PRODUCER

SINCLAIR CORPORATION Ltd.
1-4 Argyll St.
London W1F 7LD
Great Britain

www.sinclair-world.com

This product was manufactured in Czech Republic (Made in Czech Republic).

REPRESENTATIVE

SINCLAIR EUROPE spol. s r.o.
Purkynova 45
612 00 Brno
Czech Republic

TECHNICAL SUPPORT

NEPA spol. s r.o.
Purkynova 45
612 00 Brno
Czech Republic

Tel.: +420

800 100 285

Fax: [phone]

www.sinclair-solutions.com
[e-mail]