Sinclair KJR-120G User Manual

Download

Page 1

USER'S MANUAL

KJR-1 20G

WIRED CONTROLLER

Page 2

“Originalinstructions”



Page 3

● This manual gives detailed description of the precautions that should be brought to your attention during operation.

● In order to ensure correct service of the wired controller please read this manual carefully before using the unit.

● For convenience of future reference, keep this manual after reading it.

Page 4

CONTENTS

1. SAFETY PRECAUTION.............................................................................. 1

2. INSTALLATION ACCESSORY.................................................................... 2

3. INSTALLATION METHOD...........................................................................4

4. SPECIFICATION........................................................................................10

5. FEATURE AND FUNCTION OF THE WIRED CONTROLLER.................11

6. NAME ON THE LCD OF THE WIRE CONTROLLER.............................12

7. NAME OF BUTTON ON THE WIRE CONTROLLER................................13

8. PREPARATORY OPERATION..................................................................14

9. OPERATION..............................................................................................15

10. TIMER FUNCTIONS................................................................................21

11. WEEKLY TIMER......................................................................................24

12. FAULT ALARM HANDING.......................................................................31

13.TECHNICAL INDICATION AND REQUIREMENT ...................................31

Page 5

1. SAFETY PRECAUTION



Read the safety precautions carefully before installing the unit.



Stated below are important safety issues that must be obeyed.

WARNING

CAUTION

Means improper handling may lead to personal death or severe injury.

Means improper handling may lead to personal injury or property loss.

WARNING

Please entrust the distributor or professionals to install the unit. Installation by other persons may lead to imperfect installation, electric shock or fire. Adhere to this installation manual. Imporper installation may lead to electric shock or fire. Reinstallation must be performed by professionals.

Do not uninstall the unit randomly. Random uninstalling may lead to abnormal operation, heating or fire of the air condition.

NOTE

Do not install the unit in a place vulnerable to leakage of flammable gases.Once flammable gases are leaked and left around the wire controller, fire may occure. Do not operate with wet hands or let water enter the wire controller. Otherwise,

electric shock may occur.

The wiring should adapt to the wire controller current. Otherwise, electric leakage or heating may occur and result in fire. The specified cables shall be applied in the wiring. No external force may be applied

to the terminal. Otherwise, wire cut and heating may occur and result in fire.

Page 6

2. INSTALLATION ACCESSORY

Select the installation location

Don’t install at the place where cover with heavy oil, vapor or sulfureted gas, otherwise, this product would be deformed that would lead to system malfunction.

Preparation before installation

1. Please confirm that all the following parts you have been supply.

No. Name

Wire controller

Installation and owner’s manual

Screws

Wall plugs

Screws Plastic screw bars

6 7

Battery

The connective wires group

2. Prepare the following assemblies on the site.

No.

Name

Switch box

Wiring Tube(Insulating Sleeve and Tightening Screw)

Qty. Remarks



M4x20 (For Mounting on the Wall)

For Mounting on the Wall



M4x25 (For Mounting on switch box) For fixing on switch box

 

Optional



Qty.(embeded into wall)

(only for reference)

Specification

Remarks

Page 7

2. INSTALLATION ACCESSORY

Precaution of install the wire controller

1. This manual provides the installation method of wire controller. Please refer to the

wiring diagram of this installation manual to wire the wire controller with indoor unit.

2. The wire controller working in low voltage loop circuit. Forbid to directly contact the cable of 220V commercial electricity or of 380V high voltage, and don’t wire this kind of wire in the said loop; wiring clearance between configured tubes should at the range of 300~500mm or above.

3. The shielded wire of the wire controller must be grounded reliable.

4. Upon finish the wire controller connection, do not employed tramegger to detect the insulation.



Page 8

3. INSTALLATION METHOD

1.Wired remote controller structure size figure

120mm 18.5mm

123mm

Fig 3-1

2.Remove the upper part of wire controller

Insert a slot screwdriver into the slots in the lower part of the wire controller (2 places), and remove the upper part of the wire controller. (Fig.3-2)

NOTICE

The PCB is mounted in the upper part of the wire controller. Be careful not to damage the board with the slot screwdriver.

46mm

83.5mm

62mm

Slots

Fig 3-2

Page 9

3. INSTALLATION METHOD

3. Fasten the back plate of the wire controller

For exposed mounting, fasten the back plate on the wall with the 3 screws (M4×20) and plugs. (Fig.3-3)

Back plate

Screws (M4×20)

Fig 3-3

For flush-mounting, fasten the back plate on the switch box with 2 screws (M4×25) and fasten it on the wall with 1 screw (M4×20). (Fig.3-4)

Back plate

Screw (M4×20)

Screws (M4×25)

Switch box

Fig 3-4

NOTICE

Put on a flat surface. Be careful not to distort the back plate of the wire controller by overtightening the mounting screws.

Page 10

3. INSTALLATION METHOD

4. Battery installation

Fig 3-5

Put the battery into the installationsite and make sure the positive side of the battery is in accordance with the positive side of installationsite.(See Fig.3-5) Please set the time corrected on the first time operation. Batteries in the wire controller can timing under power failure which ensure the time keep right. When the power restores, if the time displayed is not correct, it means the battery is dead and replace the battery.

Page 11

3. INSTALLATION METHOD

5. Wire the indoor unit

4 methods

1 from the rear; 2 from the bottom; 3 from the top; 4 from the top center.

HA HB

PCB

HA HB

1 indoor unit 2 notch the part for the wiring to pass through with nippers, etc.

Connect the terminals on the remote controller (HA ,HB), and the terminals of the indoor unit (HA ,HB). (HA and HB do not have polarity.)

PCB

HA HB

Page 12

3. INSTALLATION METHOD

NOTE: DO NOT allow water to enter the remote control.

Use the trap and putty to seal the wires.

Putty

Trap

Putty

Trap

Fig 3-6

6. Reattach the upper part of the wire controller

After adjusting the upper case and then buckle the upper case; avoid clamping the wiring during installation. (

Fig 3-7

)

All the pictures in this manual are for explanation purpose only. Your wire controller may be slightly different .The actual shape shall prevail.

Page 13

4. SPECIFICATION

Input voltage

Ambient temperature

Ambient humidity

Wiring specifications

DC 5V/DC 12V

-5~43 °C

RH40%~RH90%

Shielded vinyl cord or cable

Wiring type

Size

2x0.75-2x1.25mm

Total length

<50m

Page 14

5. FEATURE AND FUNCTION OF THE WIRED CONTROLLER

Feature:

LCD display.

Malfunction code display: it can display the error code, helpful for service.

4-way wire layout design, no raised part at backside, more convenient to place

Swing Timer

Day off/Del

Fan speed (Lock)

Confirm Back/Turbo Copy/Ifeel

Mode

the wires and install the device.

Room temperature display.

Weekly Timer.

Function: Mode: choose Auto-Cool-Dry- Heat -Fan Fan speed: Auto/Low/Med/High speed Swing(on some models) Timer ON/OFF Temp setting Weekly timer Ifeel Child Lock LCD display Clock

Faceplate function (on some models)

----

--------

----

Page 15

6. NAME ON THE LCD OF THE WIRE CONTROLER

12345

15 14

1Operation mode indication 2Fan speed indication 3Left-right swing indication 4Up-down swing indication 5Faceplate function indication 6 Main unit and secondary unit indication 7Ifeel function indication

8 Turbo function indication 9°C / °F indication 10Temperature display 11Lock indication 12Room temperature indication 13 Clock display 14 On/Off timer 15 Timer display

Page 16

7. NAME OF THE BUTTON ON THE WIRE CONTROLER

Swing Timer

6 7

1 MODE button 2 POWER button 3 Adjust button 4 FAN SPEED button 5 SWING Button

1212

Day off/Del

Confirm Back/Turbo Copy/Ifeel

Mode

Fan speed

(Lock)

6 TIMER button 7 DAY OFF/DEL button 8 COPY/IFEEL botton 9 BACK/TURBO bottom 10 CONFIRM button

9 10 1

Page 17

8. PREPARATORY OPERATION

Set the current day and time

Timer

Press the Timer button for 3 seconds or more. The timer display will flash.

Press the button “ + ” or “ - ” to set the date. The selected date will flash.

The date setting is finished and the time setting is prepared after pressing Timer button or there is no pressing button in 10 seconds.

Press the button “+” or “-” to set the current time. Press repeatedly to adjust the current time in 1-minute increments. Press and hold to adjust the current time continuous.

ex.Monday AM 11:20

The setting is done after pressing Timer button or there is no pressing button in 10 seconds.

Page 18

9. OPERATION

To start/stop operation

To set the operation mode

Operation mode setting

Press the Power button.

Mode

Room temperature setting

Lower Raise

Press the Mode button to set the operation mode. (Heat function is invalid for cool only type unit)

Press the button“ + ”or “ - ” to set the room temperature. Indoor Setting Temperature Range :

17~30 (Depending on models).

Page 19

9. OPERATION

Fan speed setting

Press the Fan speed button to set the fan speed. (This button is unavailable when in the mode of Auto or Dry)

Fan speed (Lock)

Room temperature sensor selection

Copy/Ifeel

Press the Ifeel button to select whether the room temperature is detected at the indoor unit or the wire controller.

When the ifeel function indication appears, the room temperature is detected at the wire controller.

Indoor Unit

Page 20

9. OPERATION

Child lock function

Press the Lock botton for 3 seconds to activate the child lock function and lock all buttons on the wire controller. Press the button again for 3 seconds to deactivate the child

Fan speed (Lock)

keypad tone setting

Timer

Swing

°C & °F scale selection (on some models)

Back/Turbo

Copy/Ifeel

lock function.

When the child lock function is activated,the mark appears.

Press the buttons Swing and Timer simultaneously for 3 seconds to close the keypad tone. Press the buttons again for 3 seconds to open the keypad tone.

Press the buttons Back and Copy simultaneously for 3 seconds will alternate the temperature display between the

đē

scale.

Page 21

9. OPERATION

Turbo function (on some models)

Back/Turbo

Faceplate function (on some models)

Mode

2. Press the button “+” and “-” to control the lift and drop of the faceplate. Pressing the “+” button can stop the faceplate,while it is dropping. Pressing the “-” button can stop the faceplate,while it is lifting.

Press the Turbo button to activate the turbo function. Press the button again to deactivate the turbo function.

When the turbo function is activated,the mark appears.

1.When the unit is offˈPress the Mode button long to activate the faceplate function.The mark will flash.

The F2 mark appears when the faceplate is adjusted.

Page 22

9. OPERATION

Swing function (For the unit left & right auto swing models only)

1 Up-Down swing

Swing

Press the Swing button to start up-down swing function. Press it again to stop. When the Up-Down swing function is activated,the mark appears.

2 Left-Right swing

Swing

Press the Swing button long to start Left-Right swing function. Press it again to stop.

When the Left-Right swing function is activated, the mark appears.

Page 23

9. OPERATION

Swing function (For the unit without left & right auto swing function models)

Up-Down airflow direction and swing

Swing

Use Swing button to adjust the Up-down airflow direction.

1.Press the button every time, the louver swings 6 degrees.

2.Press and hold the button for 2 seconds,it turns into up-down swing mode, press ti again to stop. When the Up-Down swing function is activated,the mark appears. (Not applicable to all the models)

The operation can refer to the following instructions for the unit with four Up-Down louvers can be operated individually.

1.Press the Swing button to activate the Up-Down adjusting louver function. The mark will flash.(Not applicable to all the models)

2.Pressing the button “+” RUĀā can select the movement of four louvers.Each time you push the button,the wire controller select in a sequence that goes from:(the icon means the four louvers move at the same time.)

-0

-1

3. And then use Swing button to adjust the Up-Down airflow direction of the selected louver.

-3

-2

-4

Swing

Page 24

10. TIMER FUNCTIONS

WEEKLY timer Use this timer function to set operating times for each day of the week.

On timer Use this timer function to start air conditioner operation.The timer operates and air conditioner operation starts after the time has passed.

Off timer Use this timer function to stop air conditioner operation.The timer operates and air conditioner operation stops after the time has passed.

On and Off timer Use this timer function to start and stop air conditioner operation.The timer operates and air conditioner operation starts and stops after the time has passed.

Page 25

10. TIMER FUNCTIONS

To set the On or Off TIMER

Timer

Press the Timer button to select the or .

No display

Confirm

Press the Confirm button and the Clock display is flashing.

Confirm

Press the button “ + ” or “ - ” to set the time. After the time is set, the timer will start or stop automatically.

Press the Confirm button again to finish the settings.

ex.Off timer set at PM 6:00

Page 26

10. TIMER FUNCTIONS

To set the On and Off TIMER

Timer

Confirm

Press the Timer button to select the .

Press the Confirm button and the Clock display is flashing.

Confirm

Press the button “ + ” or “ - ” to set the time of On timer,and then press the Confirm button to confirm the setting.

Press the button “ + ” or “ - ” to set the time of Off timer.

Press the Confirm button to finish the settings.

Page 27

11. WEEKLY TIMER

Weekly timer setting

Timer

Day of the week setting

ON timer setting of timer setting 1

Confirm

Press the Timer button to select the .and then press the Confirm button to confirm.

Press the button “ + ” or “ - ” to select the day of the week.and then press the Confirm button to confirm the setting.

Press the button “ + ” or “ - ” to set the time of On timer.and then press the Confirm button to confirm the setting.

Page 28

11. WEEKLY TIMER

ex.Tuesday time scale 1

Up to 4 timer settings can be saved for each day of the week.It is conventent if the WEEKLY TIMER is set according to the user’s life style.

Off timer setting of timer setting 1

Confirm

Different timer settings can be setted by repeating step 3 to 4.

Other days in one week can be setted by repeating step 2 to 5.

NOTE: ● The weekly timer setting can be returned to the previous step by pressing Back button.

● The time of timer setting can be delete by pressing Dan off botton

● The current setting will be restored and withdrawn the weekly timer setting automatically when there is no operation for 30 seconds.

Press the button “ + ” or “ - ” to set the time of Off timer.and then press the Confirm button to confirm the setting.

ex.Tuesday time scale 1

Page 29

11. WEEKLY TIMER

WEEKLY timer operation

● To activate WEEKLY TIMER operation

Timer

● To deactivate WEEKLY TIMER operation

Timer

● To turn off the air conditioner during the weekly timer

Press the Timer button while is displayed on the LCD.

ex.

Press the Timer button while is disappear from the LCD.

1. If press the Power button once and quickly , the air conditioner will turn off temporarily. And the air conditioner will turn on automatically until the time of On timer.

ON OFF ON OFF

8:00 12:00 14:00 17:0010:00

ex. If press the POWER button once and quickly at 10:00, The air conditioner will turn on at 14:00.

2. When press the Power button for 2 seconds , the air conditioner will turn off completely.

Page 30

11. WEEKLY TIMER

To set the DAY OFF (for a holiday)

Confirm

During the weekly timer, press the Confirm button.

Day off/Del

Back/Turbo

● To cancel˖Follow the same procedures as those for setupǄ

● Notes: The DAY OFF setting is cancelled automatically after the set day has passed.

Press the button “ + ” or “ - ” to select the day in this week .

Press the Day off button to set the DAY OFF.

The mark is hidden

ex.The DAY OFF is set for Wednesday

The DAY OFF can be setted for other days by repeating the steps 2 and 3.

Press the Back button to back to the weekly timer.

Page 31

11. WEEKLY TIMER

DELAY function

During the weekly timer, pressing the Del button once,display " ".

Day off/Del

Copy out the setting in one day into the other day.

● A reservation made once can be copied to another day of the week. The whole reservation of the selected day of the week will be copied. The effective use of the copy mode ensures ease of making reservations.

Confirm

Press this button twice, display " " and wait 3 seconds to confirm. It means the unit will override 1 hours;

Press this button three times,display " " and wait 3 seconds to confirm. It means the unit will override 2 hours;

ex. If press the DEL button to select “ ” at 18:05 ˈ The air conditioner will delay to turn off at 20:05.

During the weekly timer, press the Confirm button.

Press the button “ + ” or “ - ” to select the day to copy from.

Page 32

11. WEEKLY TIMER

Copy/Ifeel

The mark flashes quickly

Confirm

Back/Turbo

Other days can be copied by repeating step 4 and 5.

Press the Copy button,the letter “CY” will be shown on the LCD.

Press the button “ + ” or “ - ” to select the day to copy to.

Press the Copy button to confirm .

ex. Copy the setting of Monday to Wednesday

Press the Confirm button to confirm the settings.

Press the Back button to back to the weekly timer.

Page 33

12. FAULT ALARM HANDING

If the system does not properly operate except the above mentioned cases or the above mentioned malfunctions is evident, investigate the system according to the following procedures.

12

Please check the error display of indoor unit and read <<OWNER'S MANUAL>> if other error code appears.

MALFU N C TIO N & PROT EC T ION DEFIN E

Error of communication between wire controler



and indoor unit

The faceplate is abnormal



DISPLAY

DIGITAL TUBE

13.TECHNICAL INDICATION AND REQUIREMENT

EMC and EMI comply with the CE certification requirements.

Page 34

The design and specifications are subject to change without prior notice for product improvement.Consult with the sales agency or manufacturer for details.

Page 35



Page 36

NOTE CONCERNING PROTECTION OF ENVIRONMENT

This product must not be disposed of via normal household waste after its service life, but must be taken to a collection station for the recycling of electrical and electronic devices. The symbol on the product, the operating instructions or the packaging indicate such disposal procedures. The materials are recyclable in accordance with their respective symbols. By means of re-use, material recycling or any other form of recycling old appliances you are making an important contribution to the protection of our environment. Please ask your local council where your nearest disposal station is located.

INFORMATION CONCERNING USED REFRIGERANT MEDIUM

This unit is containing fluorinated gases included in the Kyoto protocol. The maintanance and the liquidation must be carried out by qualified personel. Type of refrigerant: R410A The composition of the cooling medium R410A: (50% HFC-32, 50% HFC-125) The quantity of the refrigerant: please see the unit label. The value GWP: 2088 GWP = Global Warming Potential

In case of quality problem or other please contact your local supplier or authorized service center.

Emergency number: 112

PRODUCER

Producer: SINCLAIR CORPORATION Ltd., 1-4 Argyll St., London W1F 7LD, UK, www.sinclair-world.com This product was manufactured in China (Made in China).

REPRESENTATIVE, TECHNICAL SUPPORT

NEPA spol. s r.o. Purkyňova 45 612 00 Brno Czech republic

Tel.: +420 541 590 140 Fax: +420 541 590 124

www.sinclair-solutions.com info@sinclair-solutions.com