SIMXPERIENCE GS-5 G-FORCE SEAT Quick Start Manual

GS-5 Quick Start Guide 1.0 | Copyright SimXperience 2018

GS-5 G-FORCE SEAT

QUICK START GUIDE

2

IMPORTANT SAFETY WARNINGS

WARNING: The GS-5 G-Force Seat is NOT a toy and can produce similar g-forces to that of a real race car..

The motors will calibrate when all cables have been connected and Sim Commander is launched. Do NOT
connect all cables until the GS-5 is securely mounted and you have followed this guide

Expect unexpected movements of the G-Force panels at any time! Due to the nature of the game provided telemetry,
Sim Commander is often times responding to instructions provided by 3rd parties and cannot guarantee the accuracy or
safety of these instructions.

Tools Required

• 10 MM Socket or Wrench

• Crescent Wrench

• Tin Snips, Wire Cutter or Heavy Duty Scissors

• Included Torx key

Included Components

Congratulations on the purchase of your SimXperience GS-5 G-Force Seat!

Your GS-5 was designed to provide you with years of trouble free operation when properly configured.
If you have questions about the setup of your GS-5, please email us at [e-mail]

3

Unpacking

1. Verify shipping damage has not occurred. Contact SimXperience immediately with pictures if you observe

shipping damage and do not open the package! If the package is too badly damaged an insurance claim will be
filed and a new unit shipped. You should also consider refusing
the delivery at this juncture.

2. Remove metal straps from package with heavy duty scissors or

tin snips. BE VERY CAREFUL when doing this as the straps have a

lot of tension and can harm you or someone close if you’re not

careful. It would be wise to wear eye protection to be safe.

3. Once the straps are removed, you can open the box to expose

the GS-5 and components.

4. Carefully remove the seat and components. Everything will be

plastic wrapped together and then bolted to a 24”x24” piece of
wood.

5. First carefully remove the two zip ties holding the cables in place

(image right) with wire cutters or scissors. Be very careful not to
cut into or damage the cables. Set cables aside.

6. Remove the plastic wrap by hand. If you use a knife or box

cutter, you could damage the seat.

7. Separate all the components and then remove the 4 nuts from

the carriage bolts that attach the GS-5 to the 24”x24” plywood
sheet that was used for packaging. (Image Below Right)

8. Using a 10mm Socket or Wrench and Crescent wrench, remove

the two bolts that attach the aluminum shipping bracket. (shown in picture below).

4

9. Remove 6 attached nuts and bolts from the

back of the GS-5 (#8) to install the Headrest
(#9).

10. Install Headrest #9 using the same 6 nuts and

bolts from that you removed from GS-5 (#8).
Do not overtighten!

11. Remove Torx screws from upper GS-5 (#8) modules per image below using Torx Key (#1)

12. Locate upper panels (#7) and install using the same Torx screws you removed in step 8 with Torx Key

(#1). Tighten 8 screws per diagram (4 per panel) and do not over tighten.

5

13. Mount the seat where you will be using it with the supplied mounting bracket or optional Stage Series

Hardware. For Stage Series installation, see additional instructions that are located in the bag with the
hardware. See diagram below for usage of supplied bracket.

14. Place GS-5 Controller (#5) within reach of the GS-5 based on the cable length.

15. Plug in the USB Cable (#2) and the Power Cable to the GS-5 Controller (#5). Do not plug into wall or PC yet.

16. CAREFULLY Connect the 4 cables from the GS-5 (#8) to the GS-5 Controller (#5) with two connectors that look

like this:

WARNING: Please take note

of the 10 gold pins on the
smaller port. Incorrect
installation of these connectors
could create functionality issues.
Be careful to properly insert
them.

6

17. Carefully connect the smaller connector first Be VERY careful to properly insert it. Note the placement for the

tab (arrow below)

18. Then plug in the larger connector and make sure the clasp at the top locks and that both are firmly connected.

19. Now plug the power cord into an electrical outlet and the USB cable into an available USB port on your PC.

20. Last step is to install the seat cover. Carefully slip the seat cover over the GS-5. It can stretch, so you can work it

around the headrest. Once in place, press the 7 buttons / snaps together around the cover.

Sim Commander Software

Before your GS-5 ready for use you will need to install our Sim Commander software.
Below we have provided you with links to guides on how to do so. Once you
download, install and configure Sim Commander, your GS-5 will be ready to use.

If you already have Sim Commander installed with customer Sim Setup
Buttons (Profiles) it is best to Export / Save them first before upgrading to the
GS-5.

Sim Commander

• Quick Start Guide

• Download

Additional Guides:

• How to Auto-Tune – MUST READ!

• Create Auto-Tune from game that doesn’t support lap logging – ex. Forza

Motorsport 7

• SimVibe Setup and Configuration

All Documents, Manuals and Tutorials:

• https://simxperience.com/en-us/support/documentsandmanuals.aspx

We hope you enjoy your new GS-5 G-Force seat If you have any questions or issues, please contact us at

[e-mail].