SImx LHT0088, LHT0089, LHT0151 Installation Manual

LHT0088
LHT0089
LHT0151

SECURITY FLOODLIGHT

INSTALLATION MANUAL

Less
sensitive

More
sensitive

T

OP VIEW

200º

SIDE VIEW

12m

2.5m

A C

B

D

_____________________________

_____________________________

In this warranty:
We means Simx;
You means the consumer of the Goods

Supplier means the authorised distributor or retailer that sold you the Goods in New Zealand
or Australia; and

Goods means the Simx product accompanied by this warranty and purchased in New Zealand
or Australia.

The benefits provided to you under the following warranty are in addition to any other rights
and remedies available to you under the law:

1. If, during the time from the date of purchase (Warranty Period), there is a defect in the
Goods due to improper workmanship or material, we will replace or repair the Goods
without charge. Any replacement product is warranted only for the time remaining on the
original Warranty Period.

2. We are not obliged to replace or repair the Goods under clause 1 if the Goods have been
improperly stored, installed, connected, used, operated, repaired, damaged, abused,
tampered with, altered (without our written approval), or not maintained in accordance with
our recommended installation, connection and operating instructions.

3. The warranty provided under clause 1 is limited to replacement or repair of the Goods only,
at our option. To the extent permitted by law, we exclude liability for:

a) consequential loss or any other loss or damage caused to property or persons

arising from any cause whatsoever;

b) damage to consumable items such as lamps and starters; and

c) damage arising from normal wear and tear.

4. In order to claim under this warranty you must, within the Warranty Period, return the Goods
to the Supplier, together with the original proof of purchase including the details below:

Supplier Name _____________________________

Date Of Purchase _____________________________

Model Number _____________________________

Invoice/Receipt No. _____________________________

5. This warranty does not cover the cost of claiming under the warranty or transporting the
Goods to and from the Supplier.

Our Goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the Goods
repaired or replaced if the Goods fail to be of acceptable quality and the failure does not
amount to a major failure.

SI MX WA RR AN TY I NF OR M AT IO N

SECTION ONE

GENERAL INFORMATION

The unit utilises passive infrared technology to detect heat radiation of moving human bodies.
Upon detection, the lamp will illuminate for a user-determined time period.
An integral daylight sensor ensures night-only operation.

PARTS INCLUDED

- Luminaire c/w PIR Sensor unit.

- Instruction manual. Please keep safe for future reference.

- Accessory Pack.

- Tungsten halogen bulb

TOOLS & PARTS NEEDED

- Electric/hand-held drill & bits.

- Terminal or Electricians screwdriver

- Large slotted/philips screwdriver

- Wire cutters

Unit is for outdoor use only. Unit must be mounted on a non-flammable surface as a fixed
luminaire, and is not suitable for portable use.
The unit can get very hot during use. Ensure the unit has cooled before handling.
Ensure adequate ventilation space is allowed between the unit and any object above, in front or
to either side of the unit. Suggested space is 0.5m above, 0.3m to either side & 1.0m in front.
If in any doubt, consult a qualified tradesperson or electrician.

SECTION TWO

SELECTING THE LOCATION

The motion detector has a number of detection zones, at various vertical and horizontal angles
as shown (see diagram A).
A moving human body needs to cross/enter one of these zones to activate the sensor. The best
all-round coverage is achieved with the unit mounted at the optimum height of 2.5m.

Careful positioning of the sensor will be required to ensure optimum performance. See diagram A
detailing detection range and direction.

The sensor is more sensitive to movement ACROSS its field of vision than to movement directly
TOWARDS (see diagram B). Therefore position the unit so that the sensor looks ACROSS the
likely approach path.
Avoid positioning the sensor where there are any sources of heat in the detection area (extractor
fans, tumble dryer exhausts etc.).
Reflective surfaces (ie pools of water or white-painted walls) and overhanging branches may
cause false activation under extreme conditions.

During extreme weather conditions the motion sensor may exhibit unusual behaviour. This does
not indicate a fault with the sensor. Once normal weather conditions return, the sensor will
resume normal operation.