Simpson PT-27, PT-25S Operator's Manual

Download

Page 1

LIMITED WARRANTY (ONE YEAR)

One Year

Limited

Warranty

ON SIMPSON STRONG-TIE

BRAND TOOLS

WARNING

Simpson Strong-Tie Company Inc. (“Simpson”) provides this limited warranty to

original purchaser. This product, if properly used and maintained in compliance with

all instructions and warnings, will be free from substantial defects in material and

manufacturing for 1 year from purchase date. Purchaser’s sole remedy is replacement

upon return to Simpson within 1 year of purchase (shipping prepaid).

WHERE LAWFUL, SIMPSON DISCLAIMS ALL OTHER

WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE BEYOND THIS WARRANTY

PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS

ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE

ABOVE LIMITATION MAY NOT APPLY TO YOU. WHERE

LAWFUL, UNDER NO CIRCUMSTANCES SHALL SIMPSON

BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL

DAMAGES OR DIRECT OR INDIRECT LOSS OF ANY KIND, INCLUDING BUT NOT LIMITED

TO BODILY INJURY, DEATH OR PROPERTY DAMAGE. SIMPSON’S ENTIRE LIABILITY IS

LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION. MAY NOT APPLY TO YOU. SIMPSON IS IN NO WAY LIABLE FOR

INCIDENTS RESULTING FROM USE WITHOUT PROPER CERTIFICATION OR DISREGARD OF

INSTRUCTIONS AND WARNINGS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL

RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Read This Manual

BEFORE Operating This Tool

OPERATOR’S MANUAL

For Semiautomatic Tool Models

PT-27 and PT-25S

(.27 caliber) (.25 caliber)

The PT-27 AND PT-25S tools comply with OSHA requirements and with ANSI A10.4 2007 speciﬁcations.

Return Tools To:

Northwest U.S.A. Southwest U.S.A. Northeast U.S.A. Simpson Strong-Tie Co., Inc. Simpson Strong-Tie Co., Inc. Simpson Strong-Tie Co., Inc. 5151 S. Airport Way 260 N. Palm Street 2600 International Street Stockton, CA 95206 Brea, CA 92821 Columbus, OH 43228 (209) 234-7775 (714) 871-8373 (614) 876-8060

Southeast U.S.A. Eastern Canada Western Canada Simpson Strong-Tie Co., Inc. Simpson Strong-Tie Co., Inc. Simpson Strong-Tie Co., Inc. 2221 Country Lane 5 Kenview Boulevard 11476 Kingston Street McKinney, TX 75069 Brampton, ON L6T 5G5 Maple Ridge, BC V2X 0Y5 (972) 542-0326 (905) 458-5538 (604) 465-0296

T-SAS-PT272507 6/07

5956 W. Las Positas Blvd., Pleasanton, CA 94588 • www.simpsonanchors.com

Page 2

SAFETY STARTS WITH YOU PT-27 AND PT-25S TROUBLESHOOTING TIPS

A. TRAINING

1. All operators must complete the tool manufacturer’s training before attempting to take an exam or to operate this Simpson tool. You must obtain certiﬁcation of training from an authorized Simpson Strong-Tie® instructor. If such training is not available where you purchased the tool, call or write Simpson Strong-Tie before attempting to operate the tool for information on the nearest authorized instructor. Remember, obtaining this instruction is YOUR RESPONSIBILITY.

2. Read this manual completely and understand its contents fully before attempting to operate the tool. If there is anything in this manual that you do not fully understand, ask your instructor or call Simpson Strong-Tie for information. Reading and understanding this manual is YOUR RESPONSIBILITY.

B. LIMITATIONS

1. Just as no instruction book of any kind can forewarn a learner against all possible situations or emergencies that may arise, neither can Simpson Strong-Tie instructors or printed instructions detail all possible conditions or circumstances surrounding the use of this tool or its supporting products. Recognizing these circumstances and reacting in a safe manner is YOUR RESPONSIBILITY.

Symptom Cause Solution

Over Driving Fasteners

Tool Does Not Fire

Reduction or loss of power

Piston will not fully reset

Strip Load will not advance

Tool will not stay in closed position

Excessive Power Change to next lower power level load strip. Soft Base Material Check Base Material – Center Punch test. Tool not completely depressed Firmly depress tool before ﬁring Excessive dirt on chamber and breech Properly clean the tool. Damaged ﬁring pin or breech. Replace damaged parts. Piston is not returned to rear position Barrel must be fully opened to reset piston

Damaged piston or piston ring Replace worn parts.

Damaged piston stop Replace damaged part. Excess dirt Completely clean the tool. Bent or damaged piston Replace piston

Other damaged parts.

Strip is inserted incorrectly Check proper installation of strip

Advance mechanism is damaged

Ball bearing is missing

Tag the tool “Defective –Do not use”. Place the tool in a locked container, and contact your local Simpson representative.

Contact your local Simpson representative. Tag the tool and lock it in a container.

Contact your local Simpson representative for replacement part.

PT-27 AND PT-25S KIT CONTENTS

2. Simpson Strong-Tie disclaims any responsibility for injury or death, which may result from any disregard of this manual or the verbal instruction of the authorized Simpson Strong-Tie instructor. Following the rules of safe operation given to you here and verbally is YOUR RESPONSIBILITY.

SAFETY STARTS WITH YOU!!!

OBTAIN AUTHORIZED TRAINING

-1-

Kit also includes:

- Operators Manual

- Operators Exam

- P.A.T. Warning Sign

Lubricant

Ear Plugs

PT-27 or PT-25S Tool

Allen Wrench

Safety Glasses

Spall

Large Round Brush

Small Round Brush

Flat Brush

-18-

Page 3

MAINTAINING AND CLEANING TABLE OF CONTENTS

MAINTAINING THE PT-27 AND PT-25S TOOLS:

A clean tool always functions best. The PT-27 and PT-25S tools should be cleaned after each day of use or after 1,000 continuous fastenings.

A clean tool will:

- Help prevent the tool from accidentally discharging.

- Help maintain optimal power.

- Help prevent misﬁres (the tool not ﬁring).

CLEANING THE TOOLS:

With the provided lubricant and brushes, spray, brush, and wipe clean with a clean towel, the following parts:

1) Piston

2) Inside and outside of the Nosepiece, Baseplate and Barrel. Make certain the chamber end of the barrel is clean.

3) Inside the receiver.

Note: Make sure excess lubricant is wiped clean. Excessive lubricant can attract additional dirt.

TOOL PARTS TO BE CLEANED:

Safety Starts with You .....................................................................................1

Introduction ....................................................................................................2

General Handling of P.A.T. and Powder Loads .................................................3

Making Safe Fastenings ..................................................................................4

The “No’s” of P.A.T. Fastening .........................................................................5

Before Chambering a Powder Load ................................................................. 6

Safe Handling Practices of P.A.T. .....................................................................7

Operating Principles of P.A.T. ..........................................................................8

Schematic and Parts for the PT-27 and PT-25S .........................................9-10

Principles and Guidelines for Proper Fastening ........................................11-12

How to Load and Fire the PT-27 and PT-25S ...........................................13-15

Dismantling the PT-27 and PT-25S ..........................................................15-16

Maintaining and Cleaning ............................................................................. 17

PT-27 and PT-25S Kit Contents .....................................................................18

Troubleshooting Tips ....................................................................................18

Shear Clip Slot

Nosepiece

Inside Receiver

Annular Spring

Barrel

Piston

Piston Stop

Chamber End of Barrel

Shear Clip

Tool Warranty .................................................................................. Back Cover

INTRODUCTION

The Simpson Strong-Tie® PT-27 and PT-25S tools are low velocity or indirectacting powder actuated tools (P.A.T.). Do not attempt to operate either of these tools or any other tool before obtaining proper training and operator certiﬁcation.

READ THIS MANUAL CAREFULLY!

It will help you operate the tool with the greatest SAFETY and efﬁciency by providing you with an understanding of the safety features, operating principles and limitations of the tool and its use. Simpson Strong-Tie disclaims any responsibility for incidents resulting from the disregard of these instructions.

-2--17-

Page 4

DISMANTLING THE PT-27 AND PT-25S TOOLSGENERAL HANDLING OF P.A.T. AND POWDER LOADS

GENERAL HANDLING OF THE PT-27, AND PT-25S, AND ALL P.A.T. TOOLS

1. Always point the tool away from yourself and all bystanders.

2. Open the tool before handling to make sure it is not loaded.

3. Never place your hand over the front (muzzle) of the tool.

4. Never operate the tool without checking to see if the barrel is free of obstructions and that the tool is clean and in good working condition.

5. Never attempt to alter, modify or manufacture parts for use in your Simpson Strong-Tie® tool, this can cause malfunctions and result in unsafe functioning of the tool. Use only genuine Simpson Strong-Tie parts, fasteners and powder loads at all times.

6. Operators and bystanders must wear eye and ear protection, and head protection is recommended. Serious injury or death can occur if these safety items are not used.

7. Posting a warning sign, “Warning, Powder Actuated Tool In Use” is a minimum warning where P.A.T. tools are in use.

8. REMEMBER: use common sense and good judgement. Use these tools for their intended purpose only. Know the material you are fastening into making certain it is compatible with the powder actuated tool.

HANDLING THE PT-27 AND PT-25S, AND POWDER LOADS

3. Pull the barrel assembly out the front of the tool.

4. Lift and remove the Shear Clip from its recessed groove with a ﬂat blade screw driver.

5. Separate the front barrel, baseplate and nosepiece.

6 .Pull the piston out of the front of

the barrel.

1. Never carry powder loads in the same pocket or container with fasteners or any other hard objects.

2. Never use powder actuated loads in ﬁrearms. They are more powerful than normal small arms ammunition.

3. Never carry a loaded tool from job to job.

4. Never use the tool for anything other than its intended purpose.

5. Never use powder actuated tools in ﬂammable atmospheres.

6. Never attempt to force a load into the chamber of the tool.

7. Never strike or pry a load.

8. Always wear eye and ear protection; head protection is recommended.

9. Always properly brace yourself when working on scaffolding or ladders.

-3- -16-

The front of the tool is now fully dismantled for cleaning, and inspection for any damaged parts. Completely clean the tool, and replace any damaged parts.

Reassemble the tool in reverse order of dismantling.

After reassembling the tool, with no load strip or fastener in the tool, reset the piston by pulling the barrel assembly completely out, then push it back in.

Press the tool against a hard surface and pull the trigger. The ﬁring pin should make an audible “click” as an indication the tool was assembled properly and parts have proper functioning. If an audible ‘click” is not heard, reassemble the tool, and check for damaged parts and replace if necessary.

Page 5

HOW TO LOAD AND FIRE THE PT-27 AND PT-25S TOOLS MAKING SAFE FASTENINGS

5. After making the fastening, lift the tool off the work surface and pull the nosepiece sharply forward, or ﬂip the tool open with a snap of the wrist. This action resets the piston and advances the powder load strip to the next powder load.

6. Remove the spent powder strip load by grasping the strip from the top side of the tool and ﬁrmly pull upwards in a smooth motion.

DISMANTLING THE PT-27 AND PT-25S TOOLS :

BASE MATERIAL SUITABILITY & THE CENTER PUNCH TEST

Before loading the tool or fastening into any material, check the suitability and thickness of the base material. To check base material suitability, give it the

center punch test.

CENTER PUNCH TEST:

Using the fastener as a punch, with a hammer, strike a solid blow to the actual material you wish to fasten into, then look for these results:

1. If the point of the fastener is blunted, the material is too hard and is unsuitable. If the material is too hard, the fastener can ricochet, and possibly

escape, striking you or bystanders and cause serious injury or death.

2. If the material cracks or shatters, it is too brittle and is unsuitable. This can result in particles striking the operator or bystanders, or the fastener could pass completely through the base material causing serious injury

or death.

3. If the fastener sinks into the material with the hammer blow, the material is too soft and is unsuitable. If the material is too soft, the fastener can pass completely through and strike someone on the other side causing serious injury or death.

4. If the fastener makes a small indentation in the base the base material is suitable for fastening into.

1. Rotate the annular spring off the piston stop with a ﬂat blade screw driver or long fastener.

2. Lift the piston stop out of its recess slot.

DO NOT USE POWDER ACTUATED TOOLS FOR FASTENING INTO THESE MATERIALS:

1. Vertical mortar joints 6. Hardened or tool grade steel

2. Bricks 7. Cast iron

3. Hollow block or tile 8. Welded areas or torch cuts

4. Glazed tile 9. Spring steel

5. Glass 10. Natural rock

BASE MATERIAL THICKNESS

Thickness of the base material is perhaps the most important consideration for good safe fastenings. In concrete, the thickness must be 3 times the shank penetration; in other words, for 1" of shank penetration, the concrete must be at least 3" thick. In steel the thickness must be equal to or greater than the diameter of the shank. Fastening into any base material, which is too thin, may allow the fastener to pass through and escape - resulting in serious injury or death.

-4--15-

Page 6

THE “NO’S” OF P.A.T. FASTENING HOW TO LOAD AND FIRE THE PT-27 AND PT-25S TOOLS

GUIDELINES FOR SAFE FASTENING

1. Never Hold the tool at an acute angle to the work surface. The tool must be perpendicular to the work surface making certain that NO debris is present on the surface.

2. Never set a fastener too close to another installed fastener as this can cause a ricochet.

3. Never fasten less than 3" from the edge of unsupported concrete or masonry, or less than Z\x" from the edge of steel except for speciﬁc applications recommended by the tool manufacturer.

4. Never fasten into rough, spalled, cracked or uneven concrete. Fasten at least 3" from the outer edge of a spalled area.

5. Never fasten into material which is too hard, such as hardened steel, welds, cast steel, marble, spring steel, natural rock, etc. This could cause the fastener to shatter and escape and result in serious injury or death.

6. Never fasten into material which is too brittle, such as glass, glazed brick, glazed tile, slate, etc. This could cause the material to shatter and result in serious injury or death.

7. Never fasten into material which is too soft, such as wood, plaster, drywall composition board, plywood, etc. This could cause the fastener to pass through and escape resulting in serious injury or death.

8. Never fasten through an existing hole in any material as the fastener could hit the edge of the hole and ricochet.

9. Never leave the chamber loaded. If you decide not to make a fastening after having loaded the tool, remove both the powder load and fastener from the tool before returning it to its case.

10. Never place your hand or any part of your body over the muzzle, or point the tool toward any person when the tool is chambered with a load.

3. Select the proper strip powder load and insert it through the bottom of the tool handle until it is ﬂush with the bottom.

4. Depress the tool ﬁrmly against the work surface using both hands, then pull the trigger. Make certain you hold the tool perpendicular to the work. Using the supplied rubber spall stop will help ensure the tool is perpendicular to the work surface and will help to minimize concrete spalling when the fastener is installed.

WARNING: Always install the fastener in the tool ﬁrst,

and chamber the powder load last.

-5- -14-

Page 7

HOW TO LOAD AND FIRE THE PT-27 AND PT-25S TOOLS BEFORE CHAMBERING A POWDER LOAD

Never place your hand over the nose of the tool unless inserting a fastener and then only with the chamber empty.

1. Open the tool. Grasp the nosepiece and pull sharply forward until you feel a positive stop, then pull the nosepiece back until it stops and is fully closed. This resets the piston and positions the advance lever in the correct location for inserting the strip loads.

2. Insert the fastener into the nosepiece of the tool, head or threaded end ﬁrst. Push the fastener until the pointed end is even with the face of the nosepiece, or if a pre assembled fastener is used, until the nose piece is against the fastener accessory.

PREPARE FOR LOADING

1. Always open the tool and inspect it to be certain it is unloaded.

2. Always check to be sure that the tool is clean. Excessive dirt or debris can cause accidental ﬁring or misﬁring of the tool.

3. Never load or ﬁre the tool in an explosive atmosphere or when ﬂammables are nearby.

4. Never use improper powder loads or fasteners in the tool, as this may be unsafe or damage the tool.

5. Always insert the fastener ﬁrst, and the load last. Make sure you never double load the fasteners.

6. Never allow bystanders to gather around you when using the tool.

7. Never guess - before fastening into any unknown base material, particularly into walls, perform the center punch test described in this manual.

8. Never guess - once you determine that the base material is suitable, make a test fastening with the lowest level powder load. If that powder load does not set the fastener, try the next highest load, and so on until the fastener is properly set.

SELECTING FASTENERS AND LOADS

.27 caliber strip loads for PT-27:

Simpson Strong-Tie®

Part #

P27SL2 2 (low) P27SL3 3 P27SL4 4 P27SL5 5 (high)

Fasteners for the PT-27and PT-25S:

Simpson Strong-Tie

Fasteners

PDP-XXX .300 Headed 2-1/2" max 1-1/2" max

PDPW-XXX .300 Headed w/ 3/4" washer all 2" max PDPWL-XXX .300 Headed w/ 1" washer all 2" Max PINWP-XXX .300 Headed w/ 1-3/8" plastic washer 2-1/2" max 1-1/2" max

PINW-XXX .300 headed w/ 1-7/16" washer all 2" max

PHN-XXX 8 mm Headed 2-1/2" max 1-1/2" max

PHNW-XXX 8 mm Headed w/ 1" washer all 2" max

PSLV4-XXXXX 1/4"-20 Threaded Stud all 1-1/2" max

PDPT-XXX .300 headed Tophat all all PHCB-XXX .300 headed highway basket clip 2-1/2" max 1-1/2" max

PBXDP-XXX .300 headed BX cable strap all all

PECLDP-XXX .300 heaed ceiling clips all all

PCCXXX-DPXXX .300 headed conduit clips all all

Power

Level

Color

Brown

Green

Yellow

Red

Description PT-27 PT-25S

.25 caliber strip loads for PT-25S:

Simpson Strong-Tie®

Part #

P25SL3 3 (low) P25SL4 4 P25SL5 5 (high)

Power

Level

Color

Green

Yellow

Red

-6--13-

Page 8

SAFE HANDLING PRACTICES OF P.A.T. PRINCIPLES AND GUIDELINES FOR PROPER FASTENING

1. If the powder load does not ﬁre after pulling the trigger, hold the tool ﬁrmly against the work surface for at least 30 seconds. Carefully remove the tool from the work surface, making sure to point it away from yourself and any bystanders. Remove the load and dispose of it in a can of water. Unﬁred loads must never be thrown in trash containers or carelessly discarded in any way.

2. NEVER attempt to force or pry an unﬁred powder load from the chamber with a sharp or pointed object, as this may cause an accidental discharge.

3. NEVER attempt to disassemble a jammed tool containing a live powder load. Tag the tool “DO NOT USE” and store it safely in a locked case. Call your Simpson Strong-Tie® representative for tool repair.

4. If at any time during the operation of the tool you feel it is not working properly, STOP using it and call your Simpson Strong-Tie representative.

5. If unnecessary bystanders are in the area tell them to leave, warn all others that you are using a powder actuated tool.

6. Check the work surface to be sure it is clear of any debris. Clear away any debris so that the tool sits ﬂush on the work surface.

7. Check the work area for explosive or ﬂammable materials. If any are found remove them before operating the tool.

8. Check the chamber of the tool to be sure there is no dirt, grit or foreign objects present.

9. Check the barrel to make sure you don’t double load it with fasteners, and that it is clear of any obstruction.

10. Any tool found not to be in proper working condition shall be immediately removed from service and tagged “Defective Tool”, until it has been repaired according to manufacturer’s instructions.

BEFORE loading the tool, operate it a few times on a solid surface making certain all parts move freely and that the ﬁring pin clicks when the tool is fully depressed and the trigger is pulled. “Dry ﬁring” will not damage the tool.

FISH-HOOKING:

“Fish-hooking” is when the fastener curves when driven into concrete. This is caused by the fastener hitting large, hard, or excessive amounts of aggregate, rebar, or any hard object. Fish-hooking can reduce the holding power of the fastener, result in spalling, and may increase unsafe conditions due to escaping particles. Fish-hooking can be minimized by:

- Reducing shank penetration

- Increasing shank diameter

- Using appropriate powder load level. Excessive power can cause over driving.

- Fastening through a metal disc

FASTENING INTO STEEL:

The most common type of steel fastened into is structural steel in the form of beam, angle iron, channel, tee, plate, and strip. The holding power of the powder actuated fastener is a function of the gripping action of the steel base material around the fastener, and the fusion of the fastener to the base material.

FACTORS THAT INFLUENCE THE HOLDING POWER OF FASTENERS IN STEEL ARE:

- Shank diameter: Larger shank diameters increase holding power

- Thickness of steel base material: Thicker base material increases holding power

- Fastener Point Penetration: Getting the point to pass through base material by approximately Z\v" maximizes holding power

- Knurled Fasteners: Knurling on the fastener provides interlocking of the shank and the base material which increases the holding power

GENERAL RULES:

Minimum spacing of fasteners into steel is 1Z\x". Minimum edge distance of fasteners into steel is Z\x". Steel Thickness must be no less than the shank diameter of the fastener.

-7- -12-

Page 9

PRINCIPLES AND GUIDELINES FOR PROPER FASTENING OPERATING PRINCIPLES OF P.A.T.

FASTENING INTO MASONRY MATERIALS:

Masonry materials suitable for fastening into include:

- Poured concrete

- Precast concrete

- Pre-stressed concrete

- Grout ﬁlled concrete block

- Grouted joints

Fasteners are primarily held into masonry by a clamping of the concrete around the fastener. Factors that inﬂuence a fastener driven into concrete include:

- Depth of penetration

- Compressive strength of concrete

- Fastener spacing and edge distance

- Fastener shank diameter

- Concrete aggregate

PROPER DEPTH OF PENETRATION:

.145" Dia.

Shank Penetration

Concrete Block & Joints 1"-1Z\v" 1Z\x"-1C\v"

Concrete 2000-2500 psi

Concrete 2500-4000 psi

Precast or prestressed

concrete 4,000 psi

9-10 times Shank Dia.

or 1Z\v" -1Z\x"

7-8 times shank Dia.

or 1"-1Z\v"

5-6 times shank Dia.

or M\,"-1Z\v"

FASTENER EDGE DISTANCE ON CONCRETE:

Z\v" Stud

Penetration

1"-1Z\x"

M\,"-1"

Distance should be no closer than 3".

MINIMUM DISTANCE BETWEEN FASTENINGS: .300 and 8 mm headed fasteners – 3" spacing. Z\v" and C\," threaded fasteners – 6" spacing.

CONCRETE THICKNESS: Concrete thickness must be at least 3 times the fastener penetration.

THERE ARE TWO TYPES OF POWDER ACTUATED TOOLS:

INDIRECT-ACTING TYPE TOOL

Indirect-acting type tools work by expanding gases that act directly on a piston which drives the piston forward to strike the fastener.

➋ Piston drives forward

➊ Powder load releases energy

installs into concrete,

Power fastener

cement block or steel!

➌

The PT-27 and PT-25S are indirect-acting type tools.

DIRECT-ACTING TYPE TOOL

Direct-acting type tools work by expanding gases that act directly on the fastener without the use of a piston. Direct-acting tools are no longer manufactured in North America and are regarded as far less safe to operate than indirect-acting tools.

CAUTION: Powder actuated tools are capable of fastening into concrete and/or steel. The fastener enters the work surface with an extreme amount of energy. Make certain not to misdirect the energy.

SAFETY STARTS WITH YOU!

As the powder actuated tool operator, your safety and the safety of those around you should always be kept in mind. Consider that the least powerful load used in powder actuated tools produce approximately 10 times the power of a .22 caliber long riﬂe cartridge. Respect this power as you would a chain saw, a lawn mower, or a riﬂe.

-8--11-

Page 10

PT-25S

1. Body Assembly PT-035001

8. Receiver PT-035100

9. Annular Spring PT-035014

11. Piston Stop PT-035012

15. Barrel PT-035006

16. Piston Flat PT-035903 16a Piston-Concave PT-035217

18. Nose Piece PT-035010

19. Baseplate PT-035009

SCHEMATIC AND PARTS FOR THE PT-27 AND PT-25S TOOLS

PT-27 and PT-25S

1. Body Assem. PT-301001

2. Trigger Pin PT-301034

3. Advance Bar Hold PT-301529

4. Advance Bar PT-301530

5. Advance Bar Spr. PT-301531

6. Trigger PT-301533

7. Screw (bolt) PT-301015

8. Receiver PT-301100

9. Annular Spring PT-301014

10. Ball Bearing (6mm) PT-301013

11. Piston Stop PT-301012

12. Push Pin PT-301016

13. Ball Bearing (5mm) PT-301046

14. Spring (Mag catch) PT-301047

15. Barrel PT-301006

16. Piston Flat PT-301903 (incl. piston & ring) 16a Piston Concave PT-301217

17. Piston Ring PT-301208

18. Nose Piece PT-301010

19. Baseplate PT-301009

20. Shear Clip PT-301011

21. Sear Holder PT-301300

22. Sear PT-301023

23. Sear Spring PT-301024

24. Firing Pin Assem PT-301904

25. Spring Holder PT-301420

26. Spring PT-301421 (Firing pin return)

27. Nut PT-301422

-9- -10-

28. Spring PT-301026 (Sear Holder)

29. Spring PT-301025 (firing pin)

30. Plug PT-301028

31. Rubber Pad PT-301601

32. Rock Arm PT-301844

33. Spring (lever) PT-301840

34. Spring (trigger) PT-301843

35. Pin, Rock Arm PT-301845