Page 1
Parts Manual
Rev. 3/93
TP 400-1215-00-MM-S
20” CUT
MULCHING MOWER
Mfg. No. Description
1692317 5Hp, 20” Cut Mulching Mower
Page 2
© Copyright 1993 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed In USA.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
Page 3
4
TP 400-1215-00-MM-S
© Copyright 1997 Simplicity Manufacturing, Inc. All Rights Reserved.
All Components
The above parts group applies to the following Mfg. Nos.:
1692317 5HP, 20” Cut Mulching Mower
Page 4
5
TP 400-1215-00-MM-S
All Components
1 1713101 Deck - 20” orange
2 1935048 Nut - 5/16” flg. lock
3 1713102 Wheel arm
4 1612225 Spacer - wheel
5 1612235 Bolt - height adjuster
6 1713103 Setting lever assembly L.H.
6 1713104 Setting lever assembly R.H.
7 1917642 Washer - flat 5/16”
8 1706213 Cover- belt
9 1925592 Screw - 1/4-20 x 3/4” hex tap
10 1713105 Bracket - hinge
11 1713106 Blade - 20”
12 1713107 Blade - recut 20”
13 1713108 Decal - blade warning
14 1713109 Control -throttle w/cable
15 1713110 Cable - engine/blade control
16 1664068 Screw - #10-16 x 5/8” tap
17 1677809 Rope stop
18 1713116 Cable clamp
19 1713111 Adapter- blade
20 1713112 Spacer - blade
21 1713113 Wing nut- plastic
22 1713114 Cover- mulch 20”
23 1713115 Chute deflector assembly
24 6041612 Screw -1/4-20 x 1-1/4” truss hd.
25 1677973 Decal - CPSC danger
26 1916965 Washer - 3/8” lock H.D.
27 918312 Key - woodruff #61
28 1677816 Washer - 3/8” conical
29 1917372 Nut - 5/16-18 hex
30 1713117 Bolt - 3/8-24 x 3-1/2” HHCS Gr. 8
31 1960126 Nut -1/4 push-on
32 1612215 Plastic tip - height adjuster
33 1706215 Trailing shield - plastic
34 1677890 Washer- 1/4” curved
35 1960273 Bolt- handle
36 1706236 Handle support
37 1713118 Decal - mulch cover danger
38 1921971 Bolt - 3/8-16 x 1-3/4” HHCS Gr. 5
39 1925003 Screw - 1/4-20 x 1/2” hex tap
40 1920397 Nut - 1 /4-20 lock
41 1706237 Washer - 5/16” wave
42 1612352 Cable tie
43 1612410 Engine ring
44 1612366 Eyebolt- 1/4-20
45 1612385 Bolt - wheel
46 1612387 Stud - 1/4-20 x 3/4”
47 960293 Nut - 1/4-20 wing
48 1713119 Decal - logo 20”
49 1713120 Handle - upper
50 1713121 Bolt - handle mtg.
51 1713122 Bolt - handle support
52 1916622 Nut- 1/4-20 hex
53 921880 Washer- 1/4” star
54 6041612 Screw - 1/4-20 x 1-1/2” truss hd.
55 1713123 Bail - engine/blade control
56 1706203 Wheel - 8” push
57 1706234 Handle - lower
58 1713124 Hinge rod
59 1713125 Spring - mulch cover
60 1921319 Washer - 1 /4” flat
61 1917421 Nut - 3/8-16 hex lock
62 1713126 Decal - starting instructions
63 1713156 Decal - CPSC danger
REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION
Footnotes:
Parts are Left or Right Hand as viewed from their operator position.
Specifications are subject to change without prior notice.
The above parts group applies to the following Mfg. Nos.:
1692317 5HP, 20” Cut Mulching Mower
Page 5
Page 6
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of
in/lbs in/lbs
in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32
19
2.1
30
3.4
41
4.6
8-36
20
2.3
31
3.5
43
4.9
10-24
27
3.1
43
4.9
60
6.8
10-32
31
3.5
49
5.5
68
7.7
1/4-20
66
7.6 8 10.9 12 16.3
1/4-28
76
8.6 10 13.6 14 19.0
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Hardware Identification & Torque Specifications
Common Hardware Types
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside
Diameter
Nut, 1/2”
No
Marks
3/8” Bolt or Nut
Wrench—9/16”
3/8
5/16” Bolt or Nut
Wrench—1/2”
5/16
1/4” Bolt or Nut
Wrench—7/16”
1/4
1/2” Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
, meaning the
inside diameter
is 1/2 inch; if a
second number is present it represent the
threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
Nominal size
, or
body diameter
is 1/2 inch; the
second number represents the
threads per inch
(16 in this
example, and the final number is the
body length
of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Loading...