Simplicity DT6SY2W, DT6SY2B, DT9SY2B Instructions For Use Manual

1

2

3

min 650 mm

A

FB

C

F

E

H

90°

335

205

600 / 900

G

o 150

4

a

b

5

K

C

B

M

6

7

L

1L

2L

3L

3

2

1

0

250

95

349

420

600 / 900

270

min 485
max 955

150

8

EN 1

OPERATION AND MAINTENANCE
MANUAL

Dear customer,
You have purchased a product of our new series of
cooker hoods. We hope that our product will serve
you well and for long time. We recommend you to
study these instructions and to operate this product
according to them.

IMPORTANT INFORMATION AND
RECOMMENDATIONS

 The cooker hood should not be connected to

smoke flue, which is used for combustion exhaust

 The appliance can be used in exhaust mode (the

exhaustion of exhalations into waste air stack) or,
after additional buying of carbon filter and
recirculation set in recirculation mode (circulation
through carbon filter).

 If there is in operation simultaneously with the

cooker hood (in exhaustion mode) appliance of
type B in the same room - heat source (for
instance with gas, oil, diesel fuel or with solid
fuel), which draw combustion air directly from the
room, then it should be taken into account, that
these appliances create at combustion a certain
level of under-pressure. Therefore it is necessary
to provide a sufficient inflow of air (from the
outside environment).

 Do not handle with open flame under the cooker

hood (for instance at flambéing etc.)!

 The big fat deposits from roasting on the grease

filter should be regularly removed.

 Follow the below determined instructions at

replacing of filters.

 This appliance should be operated with adults

only.

 This appliance is designed for normal household

use.

 This appliance is not designed for use with

persons (including children), their physical,
sensual or mental disability or lack of experience
and knowledge hinders the safe use of appliance,
except when they are under supervision or they
were introduced concerning use of appliance with
the person responsible for their safety. The
children should be supervised for ensure, that
they would not play with the appliance.

 The accessible parts could be hot at using of

cooking devices.

 The cooker hood is an electric appliance with Y –

type connection. If the power cord is damaged, it
should be replaced with the producer, his/her
service technician or with similarly qualified
person, for to prevent the creation of dangerous
situation.

 The producer is not responsible for damages

caused with faulty installation or faulty using of
appliance.

ATTENTION

 Plug in cooker hood to the net before fixing on the

wall and check function of motor (all speeds) and
function of lights.

 Check whether motor is not too noisy, whether

have regular running.

 Do not remove protection foil from cooker hood

and decoration chimney.

 Check if carton box is not damaged, check

surface of cooker hood if there are not scratches
or dishing.
IN CASE OF FAILS DO NOT FIX COOKER
HOOD ON THE WALL AND CLAIMED IT AT
YOUR SALER!!!

 Fix the cooker hood on the wall with protection

foil. After fixing and setting right height
of decoration chimney remove protection foil.

 Do not move with decoration chimney without

protection foil. In other case there will be
scratches on surface.

Following these instructions you avoid useless
claiming.

DESCRIPTION (FIG.1)

A – Cooker hood
B – Lower part of decoration chimney
C – Upper part of decoration chimney
E – Carbon filter (for recirculation only)
F – Grease filter – metal cassette
M - Cover of decorative chimney
H - Switch

ELECTRIC CONNECTION

 Check before installation of appliance that the

voltage in your power net corresponds to data
given on the production sheet inside of the
appliance.

 The appliance is provided with a power cord is

ended with a plug – class I. of protection against
electric shock.

 Connect the appliance to a socket corresponding

to valid national standards.

INSTALLATION

The distance between the cooker hood and the
hotplate should not be less as 650mm (fig.2).

ATTENTION

 The attached dowels and screws are designed for

fastening of cooker hood on a wall from concrete
or full bricks. For other wall material a
corresponding type and size of dowels and
screws should be used.

 Leave the fastening of cooker hood to a

specialist!

EN 2

MOUNTING OF COOKER HOOD

 Unpack the appliance from packaging.
 Drill holes for fasteners according the drawing 3.
 Tap the fasteners to drilled holes.
 Fix the appliance with provided screws throu

holes “G”.

IMPORTANT

The horizontal location of cooker hood should
be observed.

THE EXHAUSTION VERSION

 At use of exhaustion version (see fig. 4) the

exhalations are led into the exhaustion opening
with the exhaustion hose, which is connected to
the cooker hood with a flange. The exhaustion
hose and the fastening clips should be bought
additionally.

 The exhaustion is provided through the upper

outlet of the cooker hood, on which the
exhaustion hose should be connected and the
other end of hose should be connected into the
exhaustion opening. The diameter of exhaustion
hose should be the same as the diameter of
connecting flange – e.g. Ø 150mm, or Ø 120mm
with a reduction piece (if you use connection hose
Ø 120mm, you will decrease exhaust capacity
and increase noise level).

MOUNTING OF EXHAUSTION VERSION
AND OF DECORATION CHIMNEY

 Fasten with help of a hose clip on the hinged on

cooker hood the one end of exhaustion hose,
fasten the other end into the exhaustion opening.

 Both parts (the upper C and lower B) of

decoration chimney, shifted one to the other,
place on the hinged on cooker hood.

 Shift the upper part C into the required height,

mark the upper location and mark the fastening
openings of console (K).

 Remove the decoration chimney and bore the

marked openings for the dowels.

 Screw on the console (K) together with cover of

decoration chimney (M).

 Fasten once more the both parts of decoration

chimney, shift out its upper part and fasten to the
console with two screws.

IMPORTANT

Remove protection foil from decoration chimney
not untill last assembly of decoration chimney!

IMPORTANT!

The carbon filter should not be installed in the
cooker hood at exhaustion version.

RECIRCULATION VERSION

 A carbon filter and recirculation set should be

bought for the cooker hood in recirculation
version (fig. 9). The exhalations are exhausted
through the carbon filter.(fig. 1 (E)) The circulation

air with removed smell is led with exhausted hose
through air spreader to the ventilation openings in
upper part of decorative chimney to the room.

 This version is used in cases, when there is no

waste air stack at disposal.

CAUTION!

The carbon filter should be installed in the
cooker hood at recirculation.

SETTING THE POWER LEVEL

 Power level 1, 2, 3 is set by turning the control

knob.

 If the control knob is set on 1L, 2L, 3L ventilation

and light is powered together.

TURNING ON THE LIGHTS

Light is ON when the control knob is in position “L”.

TURNING OFF THE HOOD

The hood is OFF when the control knob is in position
“0”.

MAINTENANCE AND CLEANING

 At cleaning or maintenance switch the appliance

off from the power and this with disconnecting
from the socket or with switching off of
corresponding circuit breaker.

 The regular maintenance and cleaning ensure the

efficiency, reliability and longer lifetime of cooker
hood.

 Pay special attention to grease filter and to

carbon filter.

 For cleaning of cooker hood do not use cleaning

articles containing aggressive substances mainly
chlorine and dissolvents.

GREASE METAL FILTER

 The grease metal filter (F) catches the fat

particles.

 The metal filter should be cleaned manually or in

dishwasher (at 65C) with use of appropriate
detergents.

 The filter can slightly change its color when

washed in dishwasher; nevertheless this fact has
no influence to its functionality.

 Let the filter thoroughly dry after washing and

return it to cooker hood in dry state only.

CASSETTE CARBON FILTER

 The carbon filter (E) absorbs the kitchen smell.
 The carbon filter should be never washed!

INSTALLATION OF CASSETTE CARBON
FILTER

 Disconnect the appliance from the power net.
 Take out the grease filter (F) and fasten the

cassette carbon filter (E) to its internal side – see
the picture.

EN 3

NOTICE!

The caught fat in the filter has influence not only to
the effectiveness of cooker hood but at neglected
maintenance could cause also a fire! Therefore we
recommend the observation of instructions for
cleaning and changing of filters.

LIQUIDATION OF CARBON FILTERS
AFTER FINISHED LIFETIME

 The used filters can be put to normal household

waste.

 The liquidation should be provided in

concordance with the corresponding national
standards and regulations.

LIGHTING

The cooker hood has halogen bulbs 2 x 20 W
(type 12V/20W - G4).

REPLACING OF HALOGEN BULB (FIG. 7)

 Disconnect the cooker hood from the power net.
 Shift a flat piece (a small screwdriver or flat knife)

carefully between the rings of halogen lighting.
With slight lever action make free the internal ring
with the glass cover of lighting.

 Provide the replacement of halogen bulb.
 Return back the ring with the glass cover of

lighting to original location.

CAUTION!

Do not touch the halogen bulbs with your naked
fingers

CLEANING

 Clean regularly the internal and external parts of

cooker hood with soft cleaning agents.

 Never use abrasive cleaning means.
 Clean the glass surfaces with special means for

glass, mirrors and windows.

METHOD OF USE AND LIQUIDATION OF
PACKAGING

Grooved cardboard, packaging paper

- sale to waste collecting company

- to collecting vessels for used paper

- other reuse
Polystyrene

- to corresponding collecting vessels
Packaging foil and PE backs

- to collecting vessels for plastic

LIQUIDATION OF APPLIANCE AFTER
FINISHING OF USE

This appliance is marked in accordance with
Directive 2012/19/EU on manipulation with waste
from electric and electronic equipment – WEEE.
This directive determines the unified European (EU)
frame for collection and recycling of used
equipment.

The appliance contains valuable materials which
should be reused after finishing of their use. Please
give your used appliance to waste processing
company.

CLAIMS

If there is any defect on the appliance within the
guarantee period, do not repair it self. Apply a claim
in the shop in which you bought the appliance or at
service representatives, mentioned in the Guarantee
conditions.
At applying of claim observe the text of Guarantee
sheet and Guarantee conditions.

REMARK

The producer reserves the right for providing of
minor changes, resulting from innovations or from
technologic modifications of the product.

EN 4

BASIC TECHNICAL DATA

Type

DT6SY2W

DT6SY2B

Quantity of motors

1

Max. motor capacity

200W

Lighting - halogen

2 x 20W

Total power consumption of
cooker hood

240W

Electric voltage

230V ~

Protection class against
electric shock

I.

Dimensions (mm):
w x d x h (Fig. 8)

600 x 420 x 352

Noise level

66dBA

Color – version

Inox – glass

Grease filter

2 pc – metal

Control

SWITCH

Number of capacity levels

3

Exhaustion
Exhaustion with reduction

150mm
120mm

Exhaustion

- UPPER

-RECIRCULATION

ACCESSORIES OF COOKER HOOD

Dowels and screws for mounting of cooker hood on
a wall and screws for fastening of decoration
chimney

Screws 5 x 50mm (4 pieces)

Screw 3,9 x 8mm (2pc)

Dowels H 8 (4 pieces)

Upper cover of decoration chimney for recirculation

Console for fastening of decoration chimney

Decoration chimney (2 pieces)

Backflow valve – is integral part of ventilator motor

Reduction 150 / 120mm

*The declared noise emission level of this appliance
is 66 dB(A), what represents the A level of acoustic
power in comparison to reference acoustic power
1pW.

ACCESSORIES OF COOKER HOOD FOR
ORDERING

Carbon filter – set - SAP 428642

Exhaustion hose
120 or150 mm + fastening clip

Recirculation set - SAP 431926

435005en

BASIC TECHNICAL DATA

Type

DT9SY2B

Quantity of motors

1

Max. motor capacity

200W

Lighting - halogen

2 x 20W

Total power consumption of
cooker hood

240W

Electric voltage

230V ~

Protection class against
electric shock

I.

Dimensions (mm):
w x d x h (Fig. 8)

900 x 420 x 352

Noise level

66dBA

Color – version

Inox – glass

Grease filter

3 pc – metal

Control

SWITCH

Number of capacity levels

3

Exhaustion
Exhaustion with reduction

150mm
120mm

Exhaustion

- UPPER

-RECIRCULATION

BASIC TECHNICAL DATA

Type

DT9SY2W

Quantity of motors

1

Max. motor capacity

200W

Lighting - halogen

2 x 20W

Total power consumption of
cooker hood

240W

Electric voltage

220 – 240 V ~

Protection class against
electric shock

I.

Dimensions (mm):
w x d x h (Fig. 8)

900 x 420 x 352

Noise level

66dBA

Color – version

Inox – glass

Grease filter

3 pc – metal

Control

SWITCH

Number of capacity levels

3

Exhaustion
Exhaustion with reduction

150mm
120mm

Exhaustion

- UPPER

-RECIRCULATION

FICHE

Symbol

Unit

Value

Value

Supplier’s name or trade mark

GORENJE

GORENJE

Model identification

DT6SY2W

DT6SY2B

DT9SY2W

DT9SY2B

Annual energy consumption

AEC

hood

kWh/annum

126,3

123,8

Energy Efficiency class

D

D

Fluid dynamic efficiency

FDE

hood

%

15,3

16

Fluid Dynamic Efficiency class

D

D

Lighting efficiency

LE

hood

Lux/W

13,6

8,7

Lighting Efficiency class

D

E

Grease filtering efficiency

GFE

hood

%

85

85

Grease Filtering Efficiency class

C

C

Air flow - at minimum speed in
normal use

m3/h

201

198

Air flow - at maximum speed in
normal use

m3/h

618

630

Air flow - at intensive or boost
setting

m3/h

-

-

Sound power, at minimum
speed available in normal use

A

dB

46

46

Sound power, at maximum
speed available in normal use

A

dB

66

66

Sound power, at intensive or
boost setting

A

dB

-

-

Measured power consumption
off mode

Po

W

0

0

Measured power consumption
in standby mode

Ps

W

-

-

Time increase factor

f

1,5

1,4

Energy efficiency index

EEI

hood

%

91,4

90,1

Measured air flow rate at best
efficiency point

Q

BEP

m3/h

346

350

Measured air pressure at best
efficiency point

P

BEP

Pa

291

300

Maximum air flow

Q

max

m3/h

617

630

Measured electric power input
at best efficiency point

W

BEP

W

183

182

Nominal power of the lighting
system

WL

W

40

40

Average illumination of the
lighting system on the cooking
surface

E

middle

Lux

545

347

Sound power level

LWA

dB

66

66

en