Please read this document carefully before installing and/or using
your vacuum cleaning system.
Model : _______________ Serial Number : ________________________
MaintenanceTroubleshooting
Warranty
Information
2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
including the following.
Read all instructions before using this appliance
WARNING – To reduce the risk of fire, electric shock, or injury:
1. Do not leave appliance when plugged in. Unplug from outlet when not in
use and before servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not allow to be used as a toy. Close attention is necessary when used by
or near children.
4. Use only as described in this manual. Use only manufacturer’s
recommended attachments.
5. Do not use with damaged cord or plug. If appliance is not working as it
should, has been dropped, damaged, left outdoors, or dropped into water,
return it to a service center.
6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or
pull cord around sharp edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9. Do not put any objects into openings. Do not use with any opening blocked;
keep free of dust, lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings
and moving parts.
11. Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
12. Do not use without dust bag and/or filters in place.
13. Turn off all controls before unplugging.
14. Use extra care when cleaning on stairs.
15. Do not use to pick up flammable or combustible liquids such as gasoline or
use in areas where they may be present.
16. Connect to a properly grounded outlet only. See Grounding Instructions.
Your new Simplicity central vacuum system was designed and manufactured in Blainville, Quebec, by the largest central vacuum cleaner
manufacturer in Canada, providing a high-quality, state-of-the-art product.
Our extensive network of qualified professionals ensures first quality
service near you. Contact us for the location of the Simplicity authorized
service center in your area.
sChemaTiC – UniTswiThoUTbags(C20, Ci40, Ci60 and Ci100 models)
1. Circuit Breaker
2. Low Voltage Connector
3. Serial Number
4. Integrated Inlet*
5. Air Intake
6. Integrated Switch*
7. Information center*
8. Air Exhaust
9. Muffler
* except C20 model
min. 30 cm (12")
If the muffler is turned down
6
1
2
3
4
5
min. 30 cm (12")
With mufer turned down 163 cm (64")
min. 30 cm (12")
7
8
9
min. 30 cm (12")
With mufer turned up 183 cm (72")
min. 30 cm (12")
Recommended 40 cm (16")
95 cm (38")
sChemaTiC – UniTswiTh bags(b20, bf40, bf60 and bf100 models)
1. Circuit Breaker
2. Information center *
3. Low Voltage Connector
4. Serial Number
5. Upper Round Drum Filter (part #CF-B)
6. Air Intake
7. Carbon Dust Filter*
8. Muffler
* except B20 model
min. 30 cm (12")
min. 30 cm (12")
If the muffler is turned down
7
1
2
3
4
8
5
5
6
min. 30 cm (12")
With mufer turned down 163 cm (64")
min. 30 cm (12")
min. 30 cm (12")
Recommended 40 cm (16")
95 cm (38")
With mufer turned up 183 cm (72")
6
UniT insTallaTion
Using the mounting plate provided
with your vacuum cleaner, secure
the unit to the wall (gure 1), at
a height allowing easy access
for maintenance of the filters,
dirt receptacle and/or bags (see
pages 6 and 7).
The connections to the piping
system will require some basic
tools: a mitre box and small saw
or a pipe cutter (gure 2). See
pages 9 and 10 for general instructions pertaining to the preparation
of PVC pipes. To simplify matters,
installation kits, including necessary fittings, pipes, glue and wiring,
as well as a detailed instructions
booklet, are available from
Simplicity service centers.
gure 1
gure 2
Contrary to all other connections
in the piping system, do not glue the last tting to your unit. Simplicity
central vacuums are equipped
with an adjustable air intake valve
(gure 3), which does not require
glue. An air-tight fit is achieved with
the screw-type adjustment on the
fitting itself.
Installation
gure 3
dos & don’Ts
Installing Conduits
7
Installation
8
dos & don’Ts
Installing Conduits
Installation
dos & don’Ts
Installing Inlets
When installing your vacuum inlets, we recommend that the principle of
electric polarity be taken into account. Ensure that the wire connected
onto contact A on inlet 1 is the same as that connected to contact A on
inlet 2, and so on. Do not cross, reverse or interchange wires.
A
B
A
9
Inlet 1
A
B
Inlet 1
Installation
B
Inlet 2
A
B
Inlet 2
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.