Simplicity 860E, 555M, 860M User Manual

Parts Manual
5HP Product
Mf
. No. Description
1694587 555M, 5HP 1694595 555M, 5HP
8HP Product
Mfg. No. Description
1694588 860E, 8HP 1694596 860M, 8HP
Intermediate
Walk-Behind Snowthrowers
Rev.
1731153 02/2008
Part No.:
TP 400-4148-01-IW-S
Table Of Content
s
PRODUCT COMPONENTS PAGES
Handles & Controls Group ...................................................................................................................................
Engine, Pulleys, & Frame Group - 5HP Tecumseh .............................................................................................
Engine, Pulleys, & Frame Group - 8HP Briggs & Stratton ..................................................................................
Auger & Impeller Group .......................................................................................................................................
Auger Housing Group ..........................................................................................................................................
Traction Drive Group ............................................................................................................................................
Wheels & Tires Group ..........................................................................................................................................
Decals Group .......................................................................................................................................................
Chute Crank Control Group .................................................................................................................................
12 16 18 20 24 26 28
Torque Specification Chart ..................................................................... Inside Back Cover
4 8
Handles & Controls Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070uhdc
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
4
TP 400-4148-01-IW-S
Handles & Controls Group
PART NO. DESCRIPTIONREF NO QTY.
NUT, 5/16-18 Hex Nyloc 1 5025057SM 2 BRACKET, Snow Stick- Lower 2 1726727ASM 1 SCREW, 5/16-18 x 3/4" Hex Head Cap 3 1921332SM 4 CLUTCH CABLE, Auger Drive- RH 4 7027426SM 1 HANDLE, Upper, Right Hand 5 1726574SM 1 GRIP, Clutch, RH 6 1722638SM 1 GRIP, Foam, Black 7 1726317SM 2 HAIR PIN 8 1722460SM 3 ROD, Shift, Lower 9 1666255SM 1 NUT, 1/4-20 2B Hex 10 1916622SM 2 LOCKWASHER, 1/4" Spring 11 1916964SM 3 BOLT, 1/4-20 x 2" Short Square Neck Carriage, GR 5 12 1931317SM 2 ROD, Upper, Shift 13 1720238SM 1 BLOCK, Pivot 14 1668524SM 2 SHIFT ROD PIVOT ASSEMBLY 15 1720240SM 1 SPRING, Compression 16 1715123SM 1 COTTER PIN, .125 x 1.00 17 1918452SM 1 BUSHING, .500 ID x .750 OD x .25 18 1668185SM 2 WASHER, 1/2" Flat (.531 ID x 1.250 OD x .08 Thick) 19 1924361SM 1 SHIFT ROD ASSEMBLY 20 1668523SM 1 SCREW, 1/4-20 x 2-1/4" Hex Flange Lock 21 1960705SM 1 WASHER, .250 (.27 ID x .62 OD) 22 1921319SM 2 KNOB, Tapered - 3/8-16 Internal Thread- Red 23 1726734SM 1 DASH ASSEMBLY 24 1726983ASM 1 HANDLE, Lower 25 1726572SM 1 WING KNOB, 5/16-18 26 1716632SM 2 WASHER, 5/16" Internal Tooth Lock 27 7090391SM 2 NUT, 5/16-18 Hex Flange Nyloc 28 1960686SM 4 WASHER, .312 (.34 ID x .75 OD) 29 1919326SM 2 ASSEMBLY, Rod w/Pin (Includes Ref. Nos. 31. 47, 54, 55 & 56) 30 1722633SM 1 SPRING, Compression 31 1722690SM 1 PUSH NUT 32 1960519SM 1 ROD, Hold Down 33 1722630SM 1 SCREW, 1/4-20 x 2" Hex Head Cap, GR 5 34 1960662SM 1 GRIP, Clutch, LH 35 1722667SM 1 NUT, 1/4-20 Hex Centerlock 36 1923358SM 2 SPACER, Handle 37 1715655SM 2 HANDLE, Upper, Left Hand 38 1726573SM 1 SCREW, 1/4-20 x 1-1/2" Hex Head Cap 39 1922837SM 2 SPACER, .268 ID x .394 x .165 40 1715654SM 2 SCREW, 1/4-20 x 3/4" Pan Head Torx Self-Tap 41 1960671SM 2 SCREW, 5/16-18 x 1-1/2" Hex Head Cap, GR 5 42 1921221SM 5 LEVER, Pivot 43 1722631ASM 1 NUT, 1/4-20 Hex Nyloc 44 1920397SM 2
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
5
TP 400-4148-01-IW-S
Handles & Controls Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070uhdc
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
6
TP 400-4148-01-IW-S
Handles & Controls Group
PART NO. DESCRIPTIONREF NO QTY.
TOOL, Clean-Out 45 7075909SM 1 NUT, #10-24 Hex Center Lock 46 7091267SM 1 ROD, Hand Control, not shown; part of item 30 47 1722632 1 HOLDER, Clean-Out Tool, Upper 48 1726728SM 1 CLUTCH CABLE, Ground Drive- LH 49 7027425SM 1 BOLT, 5/16-18 x 2" Curved Head Square Neck GR 2 50 7091740SM 4 WASHER, #10 Internal Tooth Lock 51 7090011SM 1 SCREW, #10-24 x 2" Hex Washer Head Machine, GR5 52 7091266SM 1 LOCKWASHER, Spring 5/16, not shown; part of item 30 53 1917356SM 4 BUSHING, .250 ID x .375 OD x .750, not shown; part of item 30 54 1722635 1 PIN, Clevis, not shown; part of item 30 55 1722634 1 SPRING, Compression, not shown, part of item 30 56 1722613 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
7
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 5HP Tecumseh
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070epi5t
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694595 - 555M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
8
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 5HP Tecumseh
PART NO. DESCRIPTIONREF NO QTY.
SCREW, 5/16-24 x 3/4" Hex Head Cap, GR 5 1 1921515SM 4 WASHER, 5/16" Flat 2 1924874SM 1 WIRE, Belt Stop 3 1725424SM 1 LOCKWASHER, 5/16" Exterior Tooth 4 1920427SM 3 ENGINE, 5HP Tecumseh, Model LH195SA-67427V 5* 1 HOSE, Oil Drain 6 1726942SM 1 NUT, 5/16-18 Hex Flange Lock- small 7 1931277SM 3 NUT, 5/16-18 Hex Flange Lock 8 1931277SM 1 ROD, Idler 9 1715092SM 1 ROLL PIN, 3/16 x 3/4" 10 2816169SM 2 FRAME ASSEMBLY, Intermediate (Orange) 11 7072566SM 1 SPEED NUT, 1/4-20 U-Type 12 1926018SM 6 BUSHING, 1.00 long 13 1666001SM 2 SUPPORT, Tie Bar 14 1715559A 1 SCREW, #10-24 x 1/2" Hex Washer Self-Tap 15 1929477SM 2 JAM NUT, 3/8-16 Hex Center Lock 16 1960251SM 4 WASHER, 3/8" Flat 17 1924940SM 3 ROD, Belt Guide 18 1674315SM 2 NUT, 3/8-16 Hex Nyloc Heavy Thin 19 1922694SM 4 SUPPORT, Frame 20 1715756A 1 SCREW, 5/16-18 x 1/2" Hex Washer Self-Tap 21 1924856SM 4 SUPPORT, Pivot 22 1715111SM 1 WASHER, 5/16" Flat 23 1919381SM 2 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 24 1922127SM 3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 25 1922127SM 1 COVER, Bottom, Orange 26 7072555SM 1 SCREW, 1/4-20 x 5/8" Hex Washer Self-Tap 27 7091819SM 9 WASHER, 7/16" Flat 28 1925125SM 1 COTTER PIN, 1/8 x 3/4" 29 1918451SM 1 IDLER ARM ASSEMBLY 30 1715112SM 1 BOLT, 3/8-16 x 1-1/4" Short Square Neck Carriage 31 1960268SM 1 SPACER, .377 ID x .75 OD x .312 Long 32 2174870SM 1 PULLEY, Idler 33 2118414SM 1 BELT, Auger Drive, V Groove 34 1717393SM 1 BELT, Traction Drive, V Groove 35 1715127SM 1 SPRING, Extension 36 1715118SM 1 PAD, Brake 37 1669313SM 1 RIVET, Blind 38 2825160SM 2 ASSEMBLY, Idler Arm w/Brake Pad 39 1717320SM 1 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5 40 7091810SM 1 WASHER, 3/8" Flat (.41 ID x 1.00 OD x .13 Thick) 41 1922755SM 1 PULLEY, Idler 42 1668477SM 1 COVER, Belt 43 1725379SM 1 SPRING, Idler- Extension 44 1720237SM 1
Footnotes
Note*See your local Tecumseh distributor for engine service parts.
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694595 - 555M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
9
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 5HP Tecumseh
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070epi5t
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694595 - 555M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
10
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 5HP Tecumseh
PART NO. DESCRIPTIONREF NO QTY.
JAM NUT, 5/16-24 Hex 45 7092031SM 1 KEY - Hi Pro .125 x .625 HP 504 SAE1035 46 2824819SM 1 PULLEY, V Groove 47 1674325SM 1 SET SCREW, 5/16-18 x 5/16" Hex Recess, Cup Point 48 7090201SM 2 PULLEY, 2.75 OD 49 1720313SM 1 KEY, 3/16 Square x 1" 50 7010061SM 1 HARNESS CLIP 51 7015861SM 1 NUT, 3/8-16 Hex Flange Lock Two Way 52 1930645SM 1 MUFFLER GUARD, Domestic (Tecumseh) 53 7028090SM 1 SCREW, #10-24 x 5/8" Hex Washer Self-Tap 54 7091075SM 1 MUFFLER GUARD, Tecumseh Engine (CE/Export), not shown; Tecumseh p/n 127-18 55 7034169SM 1 SCREW. Tecumseh Muffler, not shown; Tecumseh p/n 42-671 56 7034254SM 2 LOCK WASHER, Tecumseh Muffler, not shown; Tecumseh p/n 36-351 57 7034251SM 2 WASHER, Tecumseh Muffler, not shown; Tecumseh p/n 36-195-1 58 7034239SM 2
Footnotes
Note*See your local Tecumseh distributor for engine service parts.
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694595 - 555M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
11
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 8HP Briggs & Stratton
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070epi8b
The above parts group applies to the following Mfg. Nos.:
1694588 - 860E 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
12
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 8HP Briggs & Stratton
PART NO. DESCRIPTIONREF NO QTY.
SCREW, 5/16-24 x 1-1/4" Hex Head Cap, GR 5 1 1921982SM 4 WASHER, 5/16" Flat 2 1924874SM 1 BELT STOP, Wire 3 1725424SM 1 LOCKWASHER, 5/16" Exterior Tooth 4 1920427SM 3 ENGINE, 8 HP Briggs, Model 12E394, Type 0110, Trim E1 5* 1
5* 1
Footnotes
Note*See your local Briggs distributor for engine service parts.
ENGINE, 8HP Intek (Metric) Briggs & Stratton Model 12E396, Type 0111, Trim E1 (CE/Export)
HOSE, Oil Drain 6 1726942SM 1 NUT, 5/16-18 Hex Flange Lock- small 7 1931277SM 3 NUT, 5/16-18 Hex Flange Lock 8 1931277SM 1 ROD, Idler 9 1715092SM 1 ROLL PIN, 3/16 x 3/4" 10 2816169SM 2 FRAME ASSEMBLY, Intermediate (Orange) 11 7072566SM 1 SPEED NUT, 1/4-20 U-Type 12 1926018SM 6 BUSHING, 1.00 long 13 1666001SM 2 SUPPORT, Tie Bar 14 1715559A 1 SCREW, #10-24 x 1/2" Hex Washer Self-Tap 15 1929477SM 2 JAM NUT, 3/8-16 Hex Center Lock 16 1960251SM 4 WASHER, 3/8" SAE Flat 17 1924940SM 4 ROD, Belt Guide 18 1674315SM 2 NUT, 3/8-16 Hex Nyloc Heavy Thin 19 1922694SM 4 SUPPORT, Frame 20 1715756A 1 SCREW, 5/16-18 x 1/2" Hex Washer Self-Tap 21 1924856SM 4 SUPPORT, Pivot 22 1715111SM 1 WASHER, 5/16" Flat 23 1919381SM 2 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 24 1922127SM 3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 25 1922127SM 1 COVER, Bottom, Orange 26 7072555SM 1 SCREW, 1/4-20 x 5/8" Hex Washer Self-Tap 27 7091819SM 9 WASHER, 7/16" Flat 28 1925125SM 1 COTTER PIN, 1/8 x 3/4" 29 1918451SM 1 IDLER ARM ASSEMBLY 30 1725369SM 1 BOLT, 3/8-16 x 1-1/4" Short Square Neck Carriage 31 1960268SM 1 SPACER, .377 ID x .75 OD x .312 Long 32 2174870SM 1 PULLEY, Idler 33 2118414SM 1 BELT, Auger Drive 34 1717393SM 1 V-BELT, Traction Drive 35 1725371SM 1 SPRING, Extension 36 1715118SM 1 PAD, Brake 37 1669313SM 1 RIVET, Blind 38 2825160SM 2 ASSEMBLY, Idler Arm w/Brake Pad 39 1717320SM 1 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5 40 7091810SM 1 WASHER, 3/8" Flat (.41 ID x 1.00 OD x .13 Thick) 41 1922755SM 1 PULLEY, Idler 42 1668477SM 1 COVER, Belt 43 1725379SM 1
The above parts group applies to the following Mfg. Nos.:
1694588 - 860E 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
13
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 8HP Briggs & Stratton
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070epi8b
The above parts group applies to the following Mfg. Nos.:
1694588 - 860E 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
14
TP 400-4148-01-IW-S
Engine, Pulleys, & Frame Group - 8HP Briggs & Stratton
PART NO. DESCRIPTIONREF NO QTY.
SPRING, Extension, .562 O.D. x 4.250 Long 44 2159106SM 1 JAM NUT, 5/16-24 Hex 45 2820438SM 1 KEY - Hi Pro .125 x .625 HP 504 SAE1035 46 2824819SM 1 PULLEY, V Groove 47 1674325SM 1 SET SCREW, 5/16-18 x 5/16" Hex Recess, Cup Point 48 1960619SM 2 PULLEY, 2.75 OD 49 1720313SM 1 KEY, 3/16 Square x 1" 50 2805850SM 1 HARNESS CLIP 51 7015861SM 1 CORD, Electric Start 52 1724064SM 1 GUARD, Muffler 53 1725665A 1 MUFFLER, Deflector- B&S 54 1727032SM 1 CAPSCREW, Thread Rolling M4 x 0.7, Briggs p/n 226462 55 1727033SM 1 NUT, 3/8-16 Hex Flange Lock Two Way, Briggs p/n 810140 56 1930645SM 1
Footnotes
Note*See your local Briggs distributor for engine service parts.
The above parts group applies to the following Mfg. Nos.:
1694588 - 860E 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
15
TP 400-4148-01-IW-S
Auger & Impeller Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070aigcs
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
16
TP 400-4148-01-IW-S
Auger & Impeller Group
PART NO. DESCRIPTIONREF NO QTY.
PULLEY, Auger Input 1 1715091SM 1 SET SCREW, 5/16-18 x 1/2" Square Head Cup Point 2 1928721SM 2 KEY, 3/16 x 3/4" Woodruff 3 2805123SM 2 SET SCREW, 3/8-16 x 1/2" Square Head 4 1960474SM 1 IMPELLER ASSEMBLY 5 1715120A 1 OIL SEAL 6 1612093SM 1 BUSHING 7 1666425SM 1 PIN, Drive-Loc, 3/16 x 1-1/2" 8 2836098SM 1 COLLAR, Thrust 9 1721680SM 1 SHAFT, Rolled Worm 10 1660655SM 1 WASHER, Thrust (.562 ID x 1.000 OD x .030/.032 Thick) 11 1670971SM 1 FLANGE, Bushing 12 1666424SM 1 OIL SEAL 13 1676027SM 2 NUT 1/4-20 Hex Center Lock 14 7092126SM 6 GEAR CASE, RH- Intermediate 15 1726733SM 1 GASKET, Gear Case 16 1721676SM 1 BUSHING 17 1676026SM 2 SHAFT, Auger, 22"/24" 18 1726538SM 1 GEAR, Worm 19 1676024SM 1 GEAR CASE, LH- Intermediate 20 1726732SM 1 PIPE PLUG, 1/8-27 NPTF 3/4 Taper x .31 Long Hex Drive 21 2860625SM 1 SCREW, 1/4-20 x 7/8" Hex Head Cap, GR 5 22 7092125SM 6 FITTING, Grease 23 2821133SM 1 AUGER ASSEMBLY, 22" RH 24 1726536SM 1 AUGER ASSEMBLY, 22" LH 25 1726535SM 1 COTTER PIN, 3/32 x 3/4" 26 1918447SM 2 SHEAR PIN, .248 ID x 1-3/4" Long 27 1668344SM 2 WASHER 28 1960114SM 4 RING, Retaining 29 2827794SM 2 KEY, #605 Woodruff 30 7015894SM 1 TUBE, Low Density Polyethylene Extruded 31 1612112SM 1 FLAT WASHER, .268 ID x .591 OD x .063 Thick 32 7092127SM 12
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
17
TP 400-4148-01-IW-S
Auger Housing Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070ch3pc
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
18
TP 400-4148-01-IW-S
Auger Housing Group
PART NO. DESCRIPTIONREF NO QTY.
END PLATE, RH- Auger Housing, Orange 1 7072543SM 1 AUGER HOUSING ASSEMBLY, 22" (Orange) 2 7072548SM 1 AUGER HOUSING ASSEMBLY, 24" (Orange) 2 7072568SM 1 RETAINER NUT, 5/16-18 3 1930659SM 3 END PLATE, LH- Auger Housing, Orange 4 7072546SM 1 BLADE, Scraper- 22 inch 5 1675080A 1 BLADE, Scraper- 24 inch 5 1725352A 1 BEARING, Auger 6 1726457SM 2 RETAINER, Bearing 7 1665982ASM 1 BALL BEARING 8 2108202SM 1 SKID SHOE, Reversible, Orange 9 1727854CSM 2 WASHER, 3/8 inch Split Lock 10 1916965SM 4 BOLT, 1/4-20 x 1/2 Short Square Neck Carriage, GR 5 11 1931315SM 12 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 12 1925205SM 3 NUT, 1/4-20 Hex Flange Lock Large 13 1930641SM 12 CARRIAGE BOLT, 3/8-16 x 3/4 14 1960711SM 4 WASHER, 3/8 Flat 15 1924940SM 4 NUT, 3/8-16 Hex Nyloc 16 1960687SM 4 SCREW, 5/16-18 x 1 Hex Washer Self-Tap 17 7091841SM 6 CAP, Bearing, Orange 18 7072551SM 2 WASHER, 5/16 Split Lock 19 1917356SM 3 SCREW, 1/4-20 x 3/8 Hex Washer Self-Tap 20 1929000SM 5 RETAINER, Spout 21 7011938SM 3 SCREW, #10-24 x 5/8 Hex Washer Self-Tap 22 7091075SM 6 KNOB, Wing 5/16-18 23 1716632SM 1 WASHER, .34 x .69 x .08 Flat 24 7091076SM 2 WASHER, Nylon 25 2860210SM 3 DECAL, Hinge, Orange 26 1706085SM 2 CHUTE, Discharge 27 7073192SM 1 CARRIAGE BOLT, 5/16-18 x 3/4, GR5 28 7090316SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
19
TP 400-4148-01-IW-S
Traction Drive Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070tdg
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
20
TP 400-4148-01-IW-S
Traction Drive Group
PART NO. DESCRIPTIONREF NO QTY.
SCREW, 5/16-18 x 5/8" Hex Washer Self-Tap 1 1930601SM 3 BRACKET, Bushing 2 1673994A 1 NUT, 3/8-16 Hex, GR 5 or B 3 7091302SM 1 WASHER, 3/8" Split Lock 4 1916965SM 1 ASSEMBLY, Shift Arm w/Bushing 5 1669256SM 1 BUSHING, Spacer, .380 ID x .750 OD x 1.030 Long 6 1666114SM 1 WASHER, 3/8" SAE Flat 7 1924940SM 1 SCREW, 3/8-16 x 2" Hex Head Cap, GR 5 8 1923701SM 1 SCREW, 5/16-18 x 5/8" Hex Head Cap, GR 5 9 1925205SM 4 BALL BEARING, .669 ID x .574 OD 10 1705897SM 2 RETAINER, Bearing 11 1667341SM 2 LOCKWASHER, 5/16" Spring 12 1917356SM 4 NUT, 5/16-18 Hex, GR B or 5 13 1917372SM 7 HEX SHAFT 14 7072432SM 1 RING, External Retaining (for 3/4 Dia Shaft) 15 2827794SM 1 SCREW, 5/16-18 x 3/4" Hex Head Cap 16 1921332SM 3 DRIVEN DISC 17 7010765SM 1 HUB, Friction Disc 18 1665995SM 1 COLLAR, Thrust 19 1678956SM 2 PIN, Slide 20 1666207SM 1 SET SCREW, 1/4-20 x 1/2 w/Patch Lock 21 1724333SM 2 COLLAR, Set, 1.251 ID x 2.00 OD x .50 Long 22 1667335SM 1 SPROCKET #35, 12 Tooth 23 7072459SM 1 WASHER, 1/4 ID x 5/8 OD x .134/.109 Flat 24 1960353SM 1 LOCKWASHER, 1/4" Spring 25 1916964SM 1 SCREW, 1/4-20 x 3/4" Hex Head Cap, GR 5 26 1923341SM 1 COLLAR, Set, .756 ID x 1.249 OD x .50 27 1729254SM 1 SET SCREW, 5/16-18 x 1/2" Square Head Cup Point 28 1928721SM 2 AXLE & SPROCKET ASSEMBLY 29 7072474SM 1 CHAIN, Roller, #35, 25.5" Long 30 7072491SM 1 BUSHING 31 1715101SM 1 PULLEY, Traction 32 1715253SM 1 NUT, 5/16-18 Large Head Center Lock 33 1935048SM 2 SPACER, .328 ID x .562 OD x .144/.149 Thick 34 1665844SM 2 ASSY, Pivot Plate/Hub w/Bearing 35 1726778SM 1 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 36 1925205SM 2 WASHER 37 1666379SM 1 KEY, Hi-Pro, .188 x .62 38 2830672SM 1 DRIVE DISC, w/ Spindle 39 1719879SM 1 ROD, Pivot 40 1715131SM 1 COTTER PIN, 1/8 x 3/4" 41 1918451SM 2 NUT, 5/16-18 Hex Nyloc Light 42 1919438SM 1 WASHER, .312 (.34 ID x .75 OD) 43 1919326SM 2 BELLCRANK 44 1700473SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
21
TP 400-4148-01-IW-S
Traction Drive Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070tdg
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
22
TP 400-4148-01-IW-S
Traction Drive Group
PART NO. DESCRIPTIONREF NO QTY.
BUSHING 45 1666106SM 1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 46 1922127SM 1 WASHER, Plain, .75 ID x 1.31.OD x .10 47 1924366SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
23
TP 400-4148-01-IW-S
Wheels & Tires Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070wheel
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
24
TP 400-4148-01-IW-S
Wheels & Tires Group
PART NO. DESCRIPTIONREF NO QTY.
KLIK- PIN, .310 ID x 1-3/4" Long 1 1666969SM 2 WHEEL & TIRE ASSEMBLY, RH (Includes Ref. Nos. 3, 4 & 5) 2 1726747SM 1 VALVE STEM AND CAP 3 2172353SM 2 RIM, 6 x 3.25 (Weldment) 4 1723286SM 2 TIRE, 15 x 5.00-6, 2 Ply, Carlisle X-Trac 5 7026169SM 2 WHEEL & TIRE ASSEMBLY, LH (Includes Ref. Nos. 3, 4 & 5) 6 1726746SM 1 TUBE, Tire * 7 1664090SM 1
Footnotes
Note* Optional tire tube.
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
25
TP 400-4148-01-IW-S
Decals Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070dcl
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
26
TP 400-4148-01-IW-S
Decals Group
PART NO. DESCRIPTIONREF NO QTY.
DECAL, Dashboard, RH 1 1726946SM 1 DECAL, Dashboard, RH CE 1 1727023SM 1 DECAL, Shift Pattern 2 1715557SM 1 DECAL, Dashboard, LH 3 1727020SM 1 DECAL, Dashboard, LH CE 3 1727021SM 1 DECAL, Dash Front, Simplicity 4 1715558SM 1 DECAL, OPEI (Not Serviced) 5* 1 DECAL, Danger, Auger 6 1716532SM 1 DECAL, Auger Warning, CE 6 1727208SM 1 DECAL, Stripe, Simplicity Intermediate 555 7 1714108SM 1 DECAL, Stripe, Simplicity Intermediate 860 7 1725374SM 1 DECAL, Danger, Chute/Deflector 8 7071880SM 1 DECAL, Chute Warning, CE 8 1727207SM 1 I.D. Tag (Not Serviced) 9* 1 DECAL, Paint 10 1720454SM 1 DECAL, Lube, Controls 11 1722867SM 1 DECAL, Hinge, Orange 12 1706085SM 2
Footnotes
(Not Shown) (Used on CE Models)
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
27
TP 400-4148-01-IW-S
Chute Crank Control Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
070ccctr
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
28
TP 400-4148-01-IW-S
Chute Crank Control Group
PART NO. DESCRIPTIONREF NO QTY.
PUSH NUT, Pal. .375 Dia. Stud Cap 1 1960093SM 1 KNOB, Spinner 2 1714084SM 1 BUSHING, .376 x .437 x .20 3 1667588SM 3 ROD, Chute, Upper 4 7028152SM 1 CLIP, .093 Dia. Hair Pin 5 1960074SM 1 SPLICE, Chute Handle 6 1720577SM 1 SPRING PIN, .156 x 1.000 7 1926228SM 1 ROD, Chute Lower 8 1726939SM 1 COTTER PIN, .125 x 1.00 9 1918452SM 1 BRACKET, Universal Gear 10 1718793SM 1 WASHER, .250 (.27 ID x .62 OD) 11 1921319SM 3 RETAINER, 1/4" Bolt 12 1960518SM 2 BOLT, 1/4-20 x 5/8" Short Square Neck Carriage 13 1960252SM 2 GEAR, Universal 14 1718593SM 2 WASHER, 3/8" Flat- Black 15 1960103SM 1 SPRING PIN, .125 x .750 16 2816168SM 1 WORM SHAFT 17 7028159SM 1 NUT, 1/4-20 Hex Flange Lock 18 1960294SM 2 ROLL PIN, 1/8 x 3/4" 19 7014001SM 1 WORM 20 7028348SM 1 WASHER, .44 x .78 x .025 Curved 21 7011724SM 1 BRACKET, Worm 22 7028162SM 1 NUT, 5/16-18 Hex Flange Lock 23 7091601 1 SCREW, 5/16-18 x 5/8" Hex Head Cap, GR 5 24 1925205SM 1 SCREW, 1/4-20 x 1/2" Hex Washer Self-Tap 25 7091122SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694587 - 555M 1694588 - 860E 1694595 - 555M 1694596 - 860M
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
29
TP 400-4148-01-IW-S
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
Hardware Identification & Torque Specifications
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside Diameter
Nut, 1/2”
No
Marks
3/8” Bolt or Nut
Wrench—9/16”
3/8
5/16” Bolt or Nut
Wrench—1/2”
5/16
1/4” Bolt or Nut
Wrench—7/16”
1/4
1/2” Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16 DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Common Hardware Types
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware Grade
Size Of
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
second number is present it represent the When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the second number represents the example, and the final number is the bolt or screw (in this example 2 inches long).
, meaning the
Nominal size
inside diameter
, or
body diameter
threads per inch
is 1/2 inch; if a
threads per inch
is 1/2 inch; the
body length
(16 in this
of the
The guides and ruler furnished below are designed to help you select the appropriate hardware and tools.
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 11 15.0 17 23.1 25 34.0 5/16-24 12 16.3 19 25.8 27 34.0 3/8-16 20 27.2 30 40.8 45 61.2 3/8-24 23 31.3 35 47.6 50 68.0 7/16-14 30 40.8 50 68.0 70 95.2 7/16-20 35 47.6 55 74.8 80 108.8 1/2-13 50 68.0 75 102.0 110 149.6 1/2-20 55 74.8 90 122.4 120 163.2 9/16-12 65 88.4 110 149.6 150 204.0 9/16-18 75 102.0 120 163.2 170 231.2 5/8-11 90 122.4 150 204.0 220 299.2 5/8-18 100 136 180 244.8 240 326.4 3/4-10 160 217.6 260 353.6 386 525.0 3/4-16 180 244.8 300 408.0 420 571.2 7/8-9 140 190.4 400 544.0 600 816.0 7/8-14 155 210.8 440 598.4 660 897.6 1-8 220 299.2 580 788.8 900 1,244.0 1-12 240 326.4 640 870.4 1,000 1,360.0
1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5 b. for flange whizlock nuts and screws - use 135% of
3. Unless otherwise noted on assembly drawings, all torque values must meet this specification.
SAE Grade 2 SAE Grade 5 SAE Grade 8
in/lbs in/lbs
19
2.1
20
2.3
27
3.1
31
3.5
66
7.6 8 10.9 12 16.3
76
8.6 10 13.6 14 19.0
torques. grade 5 torques.
30 31 43 49
NOTES
in/lbs
3.4
3.5
4.9
5.5
41 43 60 68
4.6
4.9
6.8
7.7
MANUFACTURING, INC.
500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
Briggs and Stratton Yard Power Products Group
2008Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
Loading...