Simplicity 520 User Manual

Download

Parts Manual

5HP Product

. No. Description

1694585 520M, 5HP 20" (MS) 1694586 520E, 5HP 20" (ES)

520

Single-Stage Snowthrowers

Rev.

1731157 11/2007

Part No.:

TP 400-4152-01-SW-S

Table Of Content

PRODUCT COMPONENTS PAGES

Frame, Handles & Engine Group .........................................................................................................................

Auger & Drive Group ............................................................................................................................................

Auger Housing & Chute Group ............................................................................................................................

Decals Group .......................................................................................................................................................

12 16

Torque Specification Chart ..................................................................... Inside Back Cover

4 8

Frame, Handles & Engine Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178fheg

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Frame, Handles & Engine Group

PART NO. DESCRIPTIONREF NO QTY.

HANDLE, Auger Control 1 1720525SM 1 HANDLE, Upper 2 1720641SM 1 CAPSCREW, Hex Hd., 1/4-20 x 1-1/4 3 1921961SM 3 NUT,Hex Centerlock, 1/4-20 4 1923358SM 1 CABLE, Auger Control 5 1720323SM 1 TIE, Self Locking 6 1701011SM 1 BOLT, Rd. Hd., 5/16-18 x 1-3/4 7 1931338SM 2 SNAP BUSHING, 3/8 8 1716678SM 1 BRACKET, Chute Rotator Rod 9 1720574SM 1 NUT, Hex Lk., #10-24 10 1933896SM 1 NUT, Hex Lk. Esna, 1/4-20 11 1920397SM 4 KNOB, Wing 12 1716632SM 2 WASHER, Curved, 5/16 13 1717312SM 2 HANDLE, Lower 14 1720573SM 1 WASHER, 3/4 15 1919326SM 6 CAPSCREW, Hex Hd., 5/16-18 x 3/4 16 1921332SM 6 CAPSCREW, Hex Hd., 5/16-18 x 1 17 1921333SM 2 LOCKWASHER, 5/16 18 1917356SM 4 CAPSCREW, Hex Hd., 5/16-18 x 3/4 19 1921332SM 4 CORD,Extension (Electric Start Models) 20 * 1 SHAFT, Axle 21 1716608SM 1 WASHER 22 1924940SM 4 TIRE, Semi-pneumatic 23 7026240SM 2 RING, Retainer, Ext., #37 24 1716622SM 2 CAP,Hub 25 1716664SM 2 FRAME ASSY. 26 1716613SM 1 BRACKET, Reinforcement 27 1719541SM 1 NUT, Hex Lk.,Esna, 5/16-18 28 1919438SM 9 STRAP, Support 29 1720322SM 1 SCREW, Hex Wshr. Hd., #10-24 x 1-1/4 30 2860604SM 1 ENGINE, Manual Start, Model HSK850, Type 8319D 31 * 1 ENGINE, Electric Start, Model HSK850, Type 8325D 31 * 1 BRACKET, Fuel 32 1716638SM 1 CAPSCREW, Hex Hd., 1/4-20 x 3/4 33 1923341SM 2 CAP, Fuel 34 1716646SM 1 TANK, Fuel 35 1716634SM 1 WASHER 36 1921319SM 2 CLAMP, Hose 37 1679061SM 1 HOSE, Fuel, 5-1/2 long 38 1716681SM 2 CLAMP, Wire Form 39 2860112SM 3 FILTER, Gas 40 2173206SM 1 SNAP BUSHING, 1/4 41 1716676SM 1 BRACKET, Starter Handle 42 1720640SM 1 HANDLE, Start (Mitten) 43 7041954SM 1

Footnotes

Note* See your local Tecumseh distributor for service parts.

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Frame, Handles & Engine Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178fheg

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Frame, Handles & Engine Group

PART NO. DESCRIPTIONREF NO QTY.

HOLDER, Clean-Out Tool, Lower 44 7075342SM 1 HOLDER, Clean-Out Tool, Upper 45 1726728SM 1 SCREW, #10-24 x 1-1/4, Hex Head Cap 46 7091757SM 1 WASHER, #10 Internal Tooth Lock 47 7090011SM 2 NUT, #10-24 Hex Center Lock 48 7091267SM 1 TOOL, Clean-Out 49 7075909SM 1

Footnotes

Note* See your local Tecumseh distributor for service parts.

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger & Drive Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178adg

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger & Drive Group

PART NO. DESCRIPTIONREF NO QTY.

RIVET, Pop, 1/4 x 1/2 1 1960241SM 8 SCREW, Truss Head, Torx, #10-24 2 1960570SM 8 WASHER, Rivet 3 1910531SM 8 NUT, Hex Lock. ESNA, #10-24 4 1933896SM 8 FRAME, Right Side 5 1716595SM 1 BEARING, Auger 6 1665521SM 2 RETAINER, Bearing 7 1716649SM 2 AUGER ASSEMBLY, Complete (Includes Ref. Nos. 9-11) 8 1719612SM 1 KIT, Flighting Replacement (Includes Ref. Nos. 10 & 11, plus mounting hardware) 9 1686705SM 1 FLIGHT, Rubber 10 1718207SM 8 CENTER FLIGHT, Rubber 11 1716661SM 4 FRAME, Left Side 12 1716590SM 1 SCREW, Plastite, #10-14 x 5/8 13 1960001SM 1 SHIELD, Belt 14 1716619SM 1 AIR DEFLECTOR 15 1716663SM 1 SCREW, Hex Head, #10-24 x 1-1/4 16 1929477SM 1 KEY, Parallel 17 2805850SM 1 PULLEY, Drive 18 1716616SM 1 WASHER 19 1960141SM 1 LOCKWASHER, 5/16 20 1917356SM 1 CAPSCREW, Hex Head, 5/16-24 x 1-1/4 21 1921982SM 1 CAPSCREW, Hex Head, 3/8-16 x 1-1/2 22 1921969SM 1 WASHER 23 1924940SM 1 PULLEY, Idler 24 1716615SM 1 IDLER ARM 25 1716618SM 1 NUT, Flange Whiz Lock, 3/8-16 26 1931211SM 1 NUT, Hex Centerlock, 1/4-20 27 1923358SM 1 ROLLER, Belt Stop 29 1716656SM 1 SPRING, Idler Return 30 1716653SM 1 CAPSCREW, Hex Head, 1/4-20 x 1 31 1921960SM 1 CAPSCREW, Hex Head, 1/4-20 x 7/8 32 1924009SM 1 BRACKET, Belt 33 1716617SM 1 CAPSCREW, Hex Washer Head Taptite, 1/4-20 x 5/8 34 1927429SM 1 SPACER, Pulley 35 1716655SM 1 PULLEY, Driven 36 1716614SM 1 BELT, Drive 37 1716645SM 1 GUARD, Belt 38 1716589SM 1 IDLER PIVOT BOLT 39 1716654SM 1 FLANGE NUT, Ignition Switch, 5/8-32 40 1714055SM 1 CONTROL PANEL 41 1716637SM 1 LOWER HOUSING 42 1716627SM 1 WASHER 43 1921319SM 3 SCREW, Hex Head, Taptite, 1/4-20 x 7/8 44 1960568SM 2

Footnotes

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger & Drive Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178adg

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger & Drive Group

PART NO. DESCRIPTIONREF NO QTY.

SWITCH, Ignition 45 1718337SM 1 SNAP BUSHING, 1/4 46 1716676SM 1 KEY, Ignition 47 1714054SM 2 SPEED NUT, 1/4-20 48 1960595SM 1 NUT, Hex Lock, ESNA, 5/16-18 49 1919438SM 1 NUT, Hex Lock, ESNA, 1/4-20 50 1920397SM 1 SCREW, Hex Head, Taptite, #10-24 x 1/2 51 2860604SM 4 NUT, Hex Lock, #10-24 52 1933896SM 1

Footnotes

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger Housing & Chute Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178ahcg

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger Housing & Chute Group

PART NO. DESCRIPTIONREF NO QTY.

HOUSING, Upper Plastic w/Louvers 520 Snow 1 7058501SM 1 SCREW, Hex Head, Taptite, #10-24 x 1 2 1928732SM 2 NUT, Retainer, Speed, #10-24 w/Extrusion 3 1960593SM 2 COLLAR 4 1716628SM 1 CAPSCREW, Hex Head, 1/4-20 x 3/4 5 1923341SM 9 GASKET 6 1716640SM 1 RETAINER 7 1716625SM 2 RETAINER, Gasket 8 1716641SM 1 NUT, Push 9 1960521SM 8 BASE, Chute 10 1716611SM 1 NUT, Push, Pal, 3/8 11 1960093SM 1 KNOB, Chute, Rotate 12 1714084SM 1 HANDLE, Chute Rotator Upper 13 1720578SM 1 PIN, Cotter, 1/8 x 1-1/2 14 1923500SM 2 BRACKET, Gear 15 1716630SM 1 GEAR, Idler 16 1716636SM 1 DRIVE GEAR 17 1716635SM 1 SCREW, Hex Head Taptite, 1/4-20 x 5/8 18 1927429SM 4 UNIVERSAL JOINT ASSEMBLY 19 1716658SM 1 NUT, Hex 1/4-20 20 1916622SM 2 LOCKWASHER, Spring, 1/4 21 1916964SM 2 NUT, Hex Lock, ESNA, 1/4-20 22 1920397SM 11 SCREW, Plastite #10-14 x 5/8 23 1960001SM 3 HOUSING, Auger 24 1716609SM 1 WASHER 25 1921319SM 9 CARRIAGE BOLT, 1/4-20 x 7/8 26 1931318SM 4 SCRAPERBAR 27 1716606SM 1 SCOOP 28 1716596SM 1 NUT, Hex Lock, #10-24 29 1933896SM 1 NUT, Wing 5/16-18 Lock 30 1933126SM 2 SCREW, Truss Head Torx, #10-24 x 5/8 31 1960570SM 1 PLATE, Chute Base 32 1716610SM 1 SCREW, Plastite, #12-14 x 1.0 33 1960001SM 2 CARRIAGE BOLT, 5/16-18 x 3/4 34 1960282SM 3 WASHER, 5/16 35 1919326SM 3 NUT, Hex Lock, ESNA 5/16-18 36 1919438SM 4 CHUTE 37 1716612SM 1 CARRIAGE BOLT, 5/16-18 x 1 38 1931335SM 2 WASHER, Octagon 39 1716642SM 2 WASHER, Rubber 40 1716624SM 2 KNOB, Wing 41 1716632SM 1 WASHER, 1-1/2 OD 42 1920283SM 2 DEFLECTOR, Chute 43 1716631SM 1 HANDLE, Chute Rotator Lower, E-Coat 44 1720576SM 1

Footnotes

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger Housing & Chute Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178ahcg

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Auger Housing & Chute Group

PART NO. DESCRIPTIONREF NO QTY.

TUBE, Chute Handles 1/2 OD 7.00 Long E-Coat 45 1720577SM 1 PIN, Spring 5/32 X 1 SAE 1095 46 1926228SM 1 CLIP, Hair Pin .093 DIA Spring Wire 1.625LG 47 1960074SM 1

Footnotes

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Decals Group

NOTE: Unless noted otherwise, use the standard hardware torque specification chart.

178dcl

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Decals Group

PART NO. DESCRIPTIONREF NO QTY.

DECAL, Danger, Auger 1 1716532SM 1 DECAL, Logo, R.H. 2 1716665SM 1 DECAL, Power-Mass (Export Models Only) 3 1717960 1 DECAL, Danger, Discharge Chute 4 1722674SM 1 DECAL, C.E. (Export Models Only) 5 1709933SM 1 DECAL, Console (Electric Start Models) 6 1716669SM 1 DECAL, Console (Manual Start Models) 6 1716670SM 1 DECAL, OPEI 7* 1 DECAL, Auger Control 8 1716672SM 1 DECAL, Warning 9 1716671SM 1 DECAL, Compliance 10 * 1 SERIAL No. 11 * 1 DECAL, Logo, L.H. 12 1716666SM 1

Footnotes

Note* Not a Service Part.

The above parts group applies to the following Mfg. Nos.:

1694585 - 520M 1694586 - 520E

Briggs and Stratton Yard Power Products Group

TP 400-4152-01-SW-S

Hex Head Capscrew

Hex Nut

Lockwasher

Washer

Carriage Bolt

Hardware Identification & Torque Specifications

Screw, 1/2 x 2

Body

Diameter

Body

Length

Inside Diameter

Nut, 1/2”

Marks

3/8” Bolt or Nut

Wrench—9/16”

3/8

5/16” Bolt or Nut

Wrench—1/2”

5/16

1/4” Bolt or Nut

Wrench—7/16”

1/4

1/2” Bolt or Nut

Wrench—3/4”

1/2

DIA.

7/16 DIA.

7/16” Bolt or Nut

Wrench (Bolt)—5/8”

Wrench (Nut)—11/16”

Wrench & Fastener Size Guide

1/4 3/4

1/2

1/4 3/4

1/2

1/4 3/4

1/2

1/4 3/4

1/2

Common Hardware Types

Torque Specification Chart

FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)

Hardware Grade

Size Of

Standard Hardware Sizing

When a washer or nut is identified as 1/2”, this is the

Nominal size

second number is present it represent the When bolt or capscrew is identified as 1/2 - 16 x 2”, this

means the second number represents the example, and the final number is the bolt or screw (in this example 2 inches long).

, meaning the

Nominal size

inside diameter

, or

body diameter

threads per inch

is 1/2 inch; if a

threads per inch

is 1/2 inch; the

body length

(16 in this

of the

The guides and ruler furnished below are designed to help you select the appropriate hardware and tools.

Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.

8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 11 15.0 17 23.1 25 34.0 5/16-24 12 16.3 19 25.8 27 34.0 3/8-16 20 27.2 30 40.8 45 61.2 3/8-24 23 31.3 35 47.6 50 68.0 7/16-14 30 40.8 50 68.0 70 95.2 7/16-20 35 47.6 55 74.8 80 108.8 1/2-13 50 68.0 75 102.0 110 149.6 1/2-20 55 74.8 90 122.4 120 163.2 9/16-12 65 88.4 110 149.6 150 204.0 9/16-18 75 102.0 120 163.2 170 231.2 5/8-11 90 122.4 150 204.0 220 299.2 5/8-18 100 136 180 244.8 240 326.4 3/4-10 160 217.6 260 353.6 386 525.0 3/4-16 180 244.8 300 408.0 420 571.2 7/8-9 140 190.4 400 544.0 600 816.0 7/8-14 155 210.8 440 598.4 660 897.6 1-8 220 299.2 580 788.8 900 1,244.0 1-12 240 326.4 640 870.4 1,000 1,360.0

1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.

2. Recommended seating torque values for locknuts:

a. for prevailing torque locknuts - use 65% of grade 5 b. for flange whizlock nuts and screws - use 135% of

3. Unless otherwise noted on assembly drawings, all torque values must meet this specification.

SAE Grade 2 SAE Grade 5 SAE Grade 8

in/lbs in/lbs

2.1

2.3

3.1

3.5

7.6 8 10.9 12 16.3

8.6 10 13.6 14 19.0

torques. grade 5 torques.

30 31 43 49

NOTES

in/lbs

3.4

3.5

4.9

5.5

41 43 60 68

4.6

4.9

6.8

7.7

MANUFACTURING, INC.

500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA

www.simplicitymfg.com

Briggs and Stratton Yard Power Products Group

Simplicity 520 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual