Simplicity 204 User Manual

10” HEAVY

DUTY PLOW

NOTE: REPOSITION BEAM END TO THESE HOLES, WHEN

USING PLOW WITH 2-WHEEL TRACTORS.

,~fgM

b/y, opposite of Spacer

MODEL 725 RIDING TRACTOR

ASSEMBLY AND ADJUSTMENT

(

REQUIRES

1. Remove varnish from moldboard and share, using a good grade of varnish remover. (Keep greased when not in use.

2. Bolt standard ( 1

3. Bolt beam ( 3 ) to standard at ( 4 ) . Lock with jam nut so that beam is free to swing on standard.

4. Attach depth regulating yoke rod assembly ( 5 Pin and cotter pin.

5. Attach rolling coulter assembly coulter standard ( 7 ) so that blade runs approximately

l/2”

to the left of landslide. Set the rolling coulter

for best depth depending upon the soil.

)

to plow bottom ( 2 ) .

( 6 )

and adjust

#203

HITCH ADAPTER )

the plow is used Hrith the

move the Beam End to the center

Plow Beam Assembly after moving the

’

Spacer(“A”)

to outside of Beam Assem-

“B”

“725”,

of the

LANDLORD RIDING TRACTOR

CAUTION: Be sure that the rolling, coulter is out of

the ground when the tractor is in reverse gear.

6. Attach the lift pin and chain assembly ( 9 ) to the

beam at vided. The hitch ed to the tractor hitch by means of the pivot pin.

Connect pin and insert the lift pin ( 9 ) In the tractor rear lift

assembly and secure in place with a pin and s,pring clip.

7. Wheel weights should be used when operating the

10” Plow. The weights are designed so that as many

weights as necessary may be added to the wheels

( 8 )

by means of the pin and spring clip pro-

clevis

adapter ( 10 ) is then

the plow to the hitch adapter with the hitch

attach-

Lie,. in

USA

S,MPL,C,TY

MANUFACTURING COMPANY,

INC.

PLOW BOLT 704006

NUT 717006

704007 PLOW BOLT

Order by Part Number

Reference

Letter

F G

v 112057 Standard, Coulter

3 9201073

‘P

'iv

ha Aa

-a

AE 8111050

Part Description

NO.

112065 Share

1?2044 Standard

112077

11204:

112050

112051

112052

722006

112053

715036 720002 717003

8271023

713004 Set Screw, Cup Point, Sq. Hd., 3/S”-16 NC x 1” lg.

112040 Coulter Assembly, w/bushing

112058 Spindle, Coulter

‘?6!055

717018 Nut, Hex, 705046 717006

112068 Moldboard

112069 Brace, Moldboard 112066 112067

112070

112076

Beam Assembly, Plow Yoke Rod

Yoke,

L.H.

Yoke, R.H.

Pin, Yoke

Pin,

Cotter, w/extended prong, l/S” dia. x 1” lg.

End Assembly, Flow Beam

Capscrew,

Washer, Lock, 3/S”

N”t, Full Hex., 3/S”-16 NC

Clamp

Nut, Special, S/16” x 1”~ 2 l/4” lg.

Washer

Screw, Cap, Hex.,

Nut, Hex., Full,

Saddle

Landside

Angle, Slip Heel

spacer, Plow Beam

Bushing, Coulter

Pssembly

Hex Hd.,

,am, 5/E"-11NC

l/Z”-13

3/W-16

2-l/4”

NC x 1 3/4” lg.

lg.