Simplicity 1695906, 1695843, 1695735, 1695734, 1695821 User Manual
...
Setup Guide
Not for
Reproduction
Dual Stage Snow Thrower
WARNING: Always wear safety glasses or eye shields
when assembling the snow thrower.
Handle Assembly
1. Carefully unfold the handle while guiding the speed
control rod over the tire before cutting the orange ties.
2. Raise the upper handle (A, Figure 1) to the operating
position.
NOTE: Make sure the Z fi ttings at the ends of the cables are
secured in the holes on the control levers. Make sure
the cables are not caught between the upper and lower
handle.
3. Insert two bolts (B) into lower holes and fasten with two
lock washers and wing knobs (C) or nuts (if equipped).
Tighten all four fasteners securely.
4. Use the supplied ties to secure the EZ Steer™ cable (if
equipped) to the left handle and the wire harness to the
right handle.
Mfg. No.
1695734, 1695735, 1695820, 1695821, 1695824, 1695825,
1695826, 1695827, 1695843, 1695853, 1695906, 1695908,
1695964
E
G
FDH
Figure 2
A
Figure 1
Install the Speed Control Rod
Attach the ball joint (D, Figure 2), located on the bottom end
of the speed control rod (E), to the shift yoke assembly (F)
with 5/16” lock washer (G) and 5/16” nut (H). Tighten nut
securely.
B
B
C
Install the Chute Control Rod
NOTE: Some models have the chute control already installed.
Models with an electric chute do not have a control rod.
Insert the chute control handle (if equipped) through the 1.
opening in the upper handle control panel.
Insert the end of the chute control rod (2. I) into the universal joint assembly (J) located next to the chute gear.
Secure with hair pin (K).
K
I
J
Figure 3
Copyright Briggs & Stratton Corporation 1739435 (Rev. B)
Figure 4
Not for
Reproduction
Route Defl ector Cable & Clip (if included)
L
NOTE: If the chute rotation is slow or binding, loosen the
chute rotation screws (L, Figure 4) 1/4 turn.
Install the Discharge Chute
NOTE: Some models have the discharge chute already
installed.
Place discharge chute (1. M, Figure 5) over tabs on chute
ring (N) as shown.
Secure discharge chute with three carriage bolts (2. O) and
nuts (P).
M
O
P
P
Figure 5
P
N
Figure 6
Figure 7
3. Tighten hardware to 66 in-lbs (7.6 Nm).
4. Connect the wire harness (electric chute models only).
NOTE: Check all bolts and nuts in fl ange for tightness. Do not
overtighten.
CHECK OIL LEVEL
Not for
Reproduction
Remove oil dipstick (Q, Figure 8). Check oil level. Oil level
should be between FULL and ADD marks. Add oil if required
(See Operator’s Manual). Reinstall oil dipstick.
FULL
Q
Figure 8
Check the Tires
Check tires for damage. Check the air pressure in the tires
with an accurate gauge. See the sidewall of the tire for the
proper infl ation.
WARNING: Avoid Injury! Explosive separation of
tire and rim parts is possible when they are serviced
incorrectly.
• Do not attempt to mount a tire without the proper
equipment and experience to perform the job.
• Do not infl ate the tires above the recommended
pressure.
• Do not weld or heat a wheel and tire assembly. Heat can
cause an increase in air pressure resulting in an
explosion. Welding can structurally weaken or deform
the wheel.
• Do not stand in front or over the tire assembly when
infl ating. Use appropriate tool that allows you to stand
to one side.
NOTICE: Check side of tire for maximum tire pressure.
DO NOT exceed maximum.
Remove Snow Thrower from Pallet
1. Remove straps that secure snow thrower to pallet.
2. Remove snow thrower from pallet.
3. Adjust the skid shoes so that the scraper bar has 1/83/16” clearance above the ground.
Loading...