Simplicity LEGACY XL Series, LEGACY 2027 Series, LEGACY 2927 Series, 1694545 Installation Instructions Manual
Page 1
1
Installation
Instructions
Hitch & Tube Group
Mfg. No. 1694545
For Legacy XL / 2027 / 2927 Series Garden Tractors
Figure 1. Contents
Kit Contents:
Ref Part No. Qty. Description
1 1679896 1 CLAMP, Hose 6", Band Type
2 1679895 1 HOSE, Vac Col, 6 x 12
3 1930531 4 SCREW, Truss Head Phillips,
#10-32 x 1/2
4 1910531 8 WASHER, #10-32
5 1928919 4 NUT, Hex Washer Assembly,
#10-32
6 1675766 1 DECAL, Cleaning Instructions
7 1700773 1 TUBE & DECAL ASSEMBLY
(Includes Ref. No. 6)
8 1960268 4 CARRIAGE BOLT,
3/8-16 x 1-1/4
9 1724807 1 HITCH, Cross Bar
10 1725599 1 HITCH, Inner
11 1919438 6 NUT, Hex, Nylock, 3/8-16
12 1725600 2 SIDE PLATE
13 1960033 6 PIN, Hair
14 1960462 4 CAPSCREW, Hex,
1/2-13 x 2-1/2
15 1724826 4 INNER SUPPORT
16 1723163 4 SPACER
17 1916966 4 WASHER, Lock, 1/2
18 1916951 4 NUT, Hex, 1/2-13
19 1725049 4 PIN, Clevis
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
and disconnect the spark plug wire(s).
WARNING
HITCH INSTALLATION
1. Connnect the inner hitch (B, Figure 2) to the cross
bar hitch (C) using 3/8-16 x 1-1/4 carriage bolts (D)
and 3/8-16 locknuts (A).
2. Connnect the cross bar hitch (C, Figure 2) to the
side plates (E) using 3/8-16 x 1-1/4 carriage bolts (D)
and 3/8-16 locknuts (A).
Figure 2. Hitch Installation
A. Locknut,3/8-16
B. Inner Hitch
C. Cross Bar Hitch
D. Carriage Bolt, 3/8-16 x 1-1/4
E. Side Plate
A
B
A
C
D
D
E
7
15
5
4
19
616
3
2
1
18
17
18
17
6
11
9
10
11
68
12
13
15
614
Page 2
2
Installation Instructions Hitch & Tube Group
Figure 4. Hitch w/ROPS Installation
A. Hitch & Plate E. Spacers
B. Pins, Hair F. Lockwashers, 1/2
C. Capscrews, Hex, G. Nut, 1/2-13
1/2-13 x 2-1/2 H. Pin, Clevis
D. Inner Supports I. ROPS Side Plate
B
A
H
C
E
F
G
D
I
Figure 5. Hitch w/3 Point Hitch Installation
A. Hitch & Plate C. 3 Point Hitch
B. Pins, Hair D. Clevis Pins
A
B
D
C
B
Figure 3. Hitch Standard Installation
A. Hitch & Plate E. Spacers
B. Pins, Hair F. Lockwashers, 1/2
C. Capscrews, G. Nut, 1/2-13
1/2-13 x 2-1/2 H. Pin, Clevis
D. Inner Supports I. Tractor Frame
B
A
C
E
D
D
F
G
H
I
Standard Units
1. Slide capscrews (C, Figure 3) through one inner support (D), spacers (E), a second inner support (D) and
tractor frame (I). Secure with lockwashers (F) and
nuts (G).
2. Install hitches and plate (A, Figure 3) by sliding clevis
pins (H) through tractor frame (I) as shown, one inner
support (D), hitch & plate (A) and second inner support (D). Secure with hair pin (B).
Units with ROPS
1. Slide capscrews (C, Figure 4) through the inner support (D), spacers (E) and ROPS side place (I).
Secure with lockwashers (F) and nuts (G).
2. Install hitches and plate (A, Figure 4) by sliding clevis
pins (H) through ROPS side plate (I), hitch & plate (A)
and inner support (D). Secure with hair pin (B).
Units with 3-Point Hitch
1. Install hitches and plate (A, Figure 5) by sliding clevis
pins (D) through 3 Point Hitch (C), and hitch & plate
(A). Secure with hair pins (B).
Page 3
3
Hitch & Tube Group Installation Instructions
Figure 6. Discharge Tube Installation
A. Decal E. Truss Head Screw
B. Discharge Tube F. Hose
C. Locknut, Hose G. Clamp
D. Washer H. Turbo Discharge
G
H
F
A
B
C
D
E
F
G
DISCHARGE TUBE ASSEMBLY
1. Connect the flexible hose (F, Figure 6) and clear
plastic discharge tube (B). The two should overlap
by approximately 2”.
2. Secure the tubes using truss head screws (E), washers (D), and locknuts (C). Insert the screws from the
inside out and poke them through the flexible hose.
3. Insert the upper end of the clear tube into the cart
sleeve. Slide the flex hose (F) over the turbo (H) and
secure with the large hose clamp (G). The hose
should overlap the turbo discharge by 2”-3”.
The clamp screw should be positioned to the inside
as shown to prevent accidental impact and removal
of the clamp.
Check that the upper end of the clear tube (B, Figure
6) is not contacting the top of the collector cover. If
necessary, cut off the clear tube flush with the sleeve
(See Wide Body Cart Operators Manual).
Page 4
4
Installation Instructions Hitch & Tube Group
Form No. 1726330-00
Rev. 12/2003
© 2003 Simplicity Manufacturing, Inc. All Rights Reserved
TP 200-4005-00-AT-SMAN
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
NOTES
Loading...