How to use this file...(Operators Manuals)
————————————————————————————————————————————–––
Instructions for
Print Vendors (Paper Manuals)
Paper Size: * 11 x 17
* Body—50 lbs brilliant white offset or equivalent.
* Cover—on pre-printed two-tone “Swash” stock.
Press: * Body—1-color, 2-sided
* Cover imprint —1-color, 1-sided
Bindery:* Saddle Stitch, Face Trim
* Face Trim
COVERS:* This file may contain several manuals, which differ only in their covers.
* Covers are all present at the beginning of this file.
* Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover.
• Check the front cover for the individual part number (typically a 171xxxx number).
BODY: • The body of the manual is identical, regardless of the cover used.
* REMEMBER: ODD number pages are ALWAYS right hand pages, and EVEN number are ALWAYS
left hand pages.
General: * This instruction page is NOT part of the manual and must NOT be printed.
• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY,
and should NOT be printed.
————————————————————————————————————————————–––
THIS PAGE INTENTIONALLY BLANK
ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep Twin Catcher
Mfg. No. Description
1694498 Clean Sweep Twin Catcher
1726793
Rev. 02
Rev. Date 03/2004
TP 100-4033-02-AT-SN
Clean Sweep
Twin Catcher
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
www.simplicitymfg.com
© Copyright 2004 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
1
Initial Collector Assembly
Install Cover & Bags ......................................13
Normal Removal & Installation
Removing the Grass Catcher ........................14
Installing the Grass Catcher ..........................15
Hardware Identification
& Torque Specifications....................................16
NOTE: In these instructions, “left” and “right” are
referred to as seen from the operating position.
Safety Rules & Information
General Warnings............................................2
Safety Decals ..................................................2
Storing the Grass Catcher ...............................3
General Operating Information
Before Operation .............................................3
Mowing with the Catcher .................................3
Required Accessories......................................3
After Operation ................................................3
Storing the Grass Catcher ...............................3
Initial Turbo Installation
Contents Turbo Installation Kit...............................4
Turbo Installation ...................................................5
Initial Counter Balance & Front Weight Carrier
Installation -
Counter Balance Installation ...............................10
Front Weight Carrier Installation..........................10
Initial Hitch & Tube Installation
Install Hitch Plate & Back Plate ...........................11
Assemble Tubes & Deflector ...............................12
Assemble Catcher Bags......................................12
Table of Contents
2
Safety Rules
& Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of
unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed.
SAFETY DECALS
This unit has been designed and manufactured to provide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effectively, we have placed several safety labels on the unit to
remind you of this important information while you are
operating your unit.
All DANGER, WARNING, CAUTION and instructional
messages on your rider, attachments and mower should
be carefully read and obeyed. Personal bodily injury can
result when these instructions are not followed. The
information is for your safety and it is important! The
safety decals below are on your product.
If any decals are lost or damaged, replace them at once.
See your local dealer for replacements.
• Know the unit’s controls and how to stop quickly.
READ THE OPERATOR’S MANUALS.
• Read and obey all safety decals.
• Only allow responsible adults, who are familiar with
the instructions, to operate the unit.
• Disengage the PTO. Shut off the engine and wait for
all moving parts to stop before attaching, adjusting,
or disconnecting any part of the collection system.
• Check the collection system to make sure it is bolted
tightly to the unit.
• DO NOT operate the unit without either the entire
grass catcher or the deflector in place.
• Turn off the PTO to disengage the blades when not
mowing.
• DO NOT mow in reverse. Always look down and
behind before and while travelling in reverse.
• DO NOT turn sharply when travelling alongside a
building or any object. Slow down before turning.
• DO NOT carry passengers.
• When collection system is removed from the mower
deck, the deflector must be properly installed.
• Collector bags are subject to deterioration and wear
during normal use. Inspect the bag periodically for
tears, holes, or weak spots and replace with a new
bag that meets manufacturer’s durability standards.
• If the mower stalls or the collector chute plugs:
1. Disengage the PTO;
2. Stop the engine and remove the key;
3. Set the parking brake, and wait for all moving
parts to stop.
4. Remove the foreign object or clear the chute
with a piece of wood before restarting the engine.
NEVER place hands into COLLECTOR OR
MOWER housing to clear jammed objectS.
Blower OR MOWER may rotate when object is
removed.
• For added stability and to prevent tipping or loss of
control:
a. Use reduced speed on uneven ground and
when turning corners.
b. Reduce loads on hillsides. It is recommended
that the collection system be kept only half full
when negotiating any slopes. Start mowing on
slopes when the collection system is empty.
c. Mow up and down the face of slopes; never
across the face of any slope.
• When operating on slopes, use front counterweights. Never operate on slopes greater than
17.6% (10°).
GENERAL WARNINGS
TP 600-2562-01-AT-SMA
ATTACHMENT DECALS
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.
Decal - WARNING Do Not
Open Cover
Part Number 1704405
Read and obey all operation and warning decals.
Decal - WARNING
Part Number
1717291
BEFORE OPERATION
Clear the lawn of all sticks, stones, wire and other debris
which may be caught or thrown by the mower blades.
Check grass condition. If wet, wait until later in the day.
If grass is wet, the grass catcher is likely to become
plugged.
For efficient bagging, air circulation under the
mower deck, through the chute and into the bag is
very important.
For this reason, BEFORE YOU BEGIN MOWING you
should make certain the underside of the mower and
the underside of the catcher lid are free from grass and
debris.
Make sure that there is a snug fit between mower deck,
blower housing, tubes, and grass catcher cover.
MOWING WITH THE CATCHER
Always operate with throttle at full speed when mowing.
Grass should be cut often, and not too short. If grass is
too long or lush it may be necessary to keep ground
speed to a minimum or to cut only half the width of the
mower to prevent clogging. If grass is long, operate with
mower in high cutting position for first pass, cutting again
in a lower position on a second pass.
Do not open the cover with mower engaged.
If a large amount of cut grass is spilling out from under
deck, the tube may be plugged or the bags may be full—
discontinue mowing, stop the unit, disengage the PTO,
shut off the engine and then empty the catcher or clear
the tube.
General
Operating Instructions
WARNING
ALWAYS shut off the tractor. Disengage the PTO,
and allow all moving parts to stop BEFORE
disconnecting or clearing tube, or emptying
catcher.
Before leaving the operator’s position for any
reason, engage the parking brake, disengage the
PTO, stop the engine and remove the key.
To reduce fire hazard, keep the engine, rider and
mower free of grass, leaves and excess grease.
Do not stop or park rider over dry leaves, grass or
combustible materials.
REQUIRED ACCESSORIES
A front-mounted factory approved weight carrier and 66
lbs. worth of weights are required when using this rearmounted grass catcher. Never operate on slopes
greater than 17.6% (10°).
AFTER OPERATION
Remove any debris from the the screen on the underside
of the lid.
Note: The lid screen can be partially removed
for easier cleaning and should be cleaned regularly.
The blower housing and tube should be removed for
cleaning.
Inspect the grass bags for wear or damage. Make sure
that there is a snug fit between mower deck, blower
housing, tubes, and grass catcher cover.
STORING THE GRASS CATCHER
Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove
any debris from the the screen on the underside of the
lid.
If paint has been scratched on metal parts, touch up with
paint, or apply a thin film of oil to prevent corrosion.
Store in a dry area. Dry thoroughly before storing for a
long period of time. Always store away from moisture.
Do not leave grass in bagger containers. Empty
containers after each use and before storing.
Failure to do so may result in spontaneous
combustion which could develop into a fire.
CAUTION
CAUTION
Before you begin operating the unit be certain
you have read all of the safety and operational
information of this instruction sheet, as well as
the Operator’s Manual for the tractor and any
other attachments.
3
Initial Turbo
Installation
4
Ref.Qty. Description
1 2 CAPSCREW, Hex Head, 5/16-18 x 1
2 6 WASHER, 5/16
3 1 SUPPORT, Belt Cover
4 4 NUT, Hex, Nylon Lock, #10-24
5 1 ROD, Deflector
6 4 SCREW, Truss Head, #10-24 x 3/4
7 1 PIVOT ASSEMBLY
8 4 NUT, Hex Whizlock, 5/16-18
9 1 NUT, Nylock, Hex 5/16-18
10 1 COVER-BELT 50"
11 1 DECAL, Warning
12 1 COVER-BELT 44"
13 1 NUT, Hex, 3/8-16
14 1 LOCKWASHER, 3/8
15 1 BRACKET, Idler
16 1 LATCH, Belt Cover
17 2 WASHER, Flat, 3/8
18 1 CAPSCREW, Hex Head, 3/8-16 x 2
19 1 PULLEY ASSEMBLY, Idler
20 1 BELT STOP
21 1 CAPSCREW, 5/16-18 x 1-1/2
22 3 LOCKWASHER, 5/16
23 1 SPACER
24 1 NUT, Sleeve
25 1 WASHER, Belleville
26 1 PULLEY
27 1 HUB
28 1 PLATE ,Spring Support
29 1 SPACER, Pulley
30 1 CAPSCREW, Hex Head, 5/16-18
31 1 WASHER, 5/16
32 1 LATCH, Spring
33 1 SPACER
34 1 WASHER,3/8
35 1 V-BELT, 50” Turbo
36 1 NUT, Hex Lock, 5/16-18
37 1 NUT,Wing, Special, 5/16
38 2 NUT, Hex, 5/16-18
39 1 BRACKET, Anchor
40 1 CARRIAGE BOLT, 5/16-18
41 1 BRACKET ASSEMBLY, Cutoff
42 1 SPACER
43 1 BRACKET
44 2 CAPSCREW, Hex Head, 5/16-18 x 7/8
45 1 CARRIAGE BOLT, 5/16-18 x 3/4
46 1 SPRING, Compression
47 1 SPACER, Spring Holder
48 1 BRACKET, Mounting
49 1 V-BELT, 44” Turbo
Figure 1. Contents of Turbo Installation Kit
48
49
11
12
44"
35
10
1
2
1
3
4
6
5
27
45
27
34
27
8
50"
9
7
8
14
15
16
13
18
17
18
33
19
21
20
22
8
2
23
32
31
30
39
Existing
Hardware
17
Torque to
55-70 ft. lbs.
24
25
29
26
27
Existing Pulley
& Spacer
37
38
22
47
46
36
38
22
43
42
41
40
44
Existing Hardware
(Bolt, Washer, Lockwasher, & Nut)
28
Existing Hardware
Initial Turbo Installation
5
Install Deflector Hinge Assembly
1. Remove the bolts (A, Figure 2) securing the RH arbor
cover, then remove the cover from the deck. Discard
the cover and bolts (A).
2. Remove and discard the plastic plugs from the deck
at the locations used by bolts (F & B, Figure 5).
3 Slide the deflector rod (D) through the pivot bracket
(E).
4 Secure the front of the pivot bracket with a 5/16-18 x
3/4” carriage bolt (F) and flange whizlock nut (C).
5 Secure the back of the pivot bracket (E) and belt
cover support (A) with a 5/16-18 x 1 capscrew (B),
5/16 washer (G), and flange whizlock nut (C).
Install Discharge Baffle
1. Attach the baffle bracket (A, Figure 4) under the
mower housing as shown, and insert the carriage bolt
(from step 1) through the bracket & deck hole at (B).
2. Attach the “L” bracket (C) to the baffle (A), and over
the stone guard (D). Attach with carriage bolt, spacer,
lockwasher and nut as shown.
TURBO INSTALLATION
Remove Mower Deck
Remove the mower deck from the unit (see Operator’s
Manual for instructions).
Deflector Removal
1. Remove and retain the carriage bolts, washers, lockwashers, and nuts (A, Figure 3) holding the deflector
rod to the deck. Remove and discard the deflector
rod. Retain the deflector.
E
F
C
C
G
D
B
A
A
Figure 4. Install Discharge Baffle
A. Baffle Bracket C. L-Bracket
B. Mounting Hole D. Stone Guard
Figure 3. Remove Deflector
A. Carriage Bolts, Washers, Lockwashers, & Nuts
Figure 5. Install Deflector Hinge
A. Belt Cover Support F. 5/16-18 x 3/4
B. 5/16-18 x 1 Capscrew Carriage Bolt
C. 5/16-18 Whizlock Nuts G. 5/16 Washer
D. Deflector Support Rod
E. Pivot Bracket
A
B
C
D
A
Figure 2. Install Discharge Baffle
A. Cover and Bolts
Initial Turbo Installation
6
Install Deflector
1. See Figure 6. Drill four 13/64” holes from the bottom
of the deflector at the pre-molded drill points (A, bottom of deflector).
2. Attach the deflector to the support rod wire-form
using four #10-14 x 3/4 truss head screws and nylock
nuts.
C
B
Figure 6. Install Deflector
A. 13/64 Hole Locations C. Screws, #10-24 x 3/4
B. Nylock Nuts
Install Belt Guide
1. See Figure 7 & 8. Locate the taptite screw that will
be replaced by capscrew (C). Remove and discard
the taptite screw
2. Assemble the 5/16-18 x 1-1/2 capscrew (C), lockwasher (E), washers (B), belt stop (D) and spacer
(A).
3. Secure the belt stop assembly to the deck in the location shown.
Note The belt stop (D, Figures 7 & 8) is located and oriented differently in 44” and 50” applications. For all
applications, when turbo is installed, belt stop (D) should
be outside the belt 1/8” away from the backside of the
belt.
C
E
D
A
Figure 8. Install Belt Guide
A. Spacer D. Belt Stop
B. 5/16 Washers E. Lockwasher,
C. Capscrew, 5/16-18 x 1-1/2 5/16
B
44” Models
C
E
D
A
Figure 7. Install Belt Guide
A. Spacer D. Belt Stop
B. 5/16 Washers E. Lockwasher,
C. Capscrew, 5/16-18 x 1-1/2 5/16
B
50” Models
A
Initial Turbo Installation
7
Install Idler Assembly & Belt Cover
1. See Figure 9. Remove and discard the two taptite
screws from locations (E).
2. Insert two 5/16-18 x 7/8 capscrews (C) through the
mower deck and arbor. Tighten the capscrews.
3. Mount the idler pulley assembly (A) to the deck using
the two 5/16-18x 7/8 capscrews (C) and 5/16-18 whizlock nuts (D).
Install Turbo Drive Pulley
1. See Figure 10. Remove the arbor drive belt from the
right side arbor pulley.
2. Remove and discard the flange nut and spring washers securing the arbor pulley and spacer (A). Retain
the pulley and spacer (A).
3. Install the new spacers (B&F), turbo drive pulley (C),
spring washer (D), and sleeve nut (E). Be sure the
notches in the pulleys and spacers are aligned.
Install the spring washer concave side down. Torque
the sleeve nut to 55-70 ft. lbs. (74-95 N.m).
4. Reinstall the arbor drive belt on the lower pulley.
A
D
B
C
D
E
B
C
A
Figure 9. Install Idler Assembly
A. Idler Assembly. D. Locknuts, 5/16-18
B. Belt Guide E. Taptite Screws
C. Capscrew, 5/16-18 x 7/8
Figure 10. Install Turbo Drive Pulley
A. Original Pulley & Spacer D. Spring Washer
B. Spacer, W/Groove(New) E. Sleeve Nut
C. Pulley (New) F. Spacer (New)
Original
Pulley and
Spacer
E
Torque to
55-70 ft. lbs.
Install Anchor Bracket
1. See Figure 12. If not already done, assemble the
anchor bracket and related components as shown in
Figure 11.
2. Attach the anchor bracket assembly (B, Figure 12) to
the mower deck using 5/16-18 x 1 capscrews (A) and
5/16-18 locknuts (C).
NOTE: The deflector latch MUST secure the deflector in
a down position—as shown in Figure 7.
B
Figure 12. Anchor Bracket Installation
A. Capscrews, 5/16-18 x 1 C. Locknut, 5/16-18
B. Anchor Bracket
Figure 11. Anchor Bracket Assembly
A. Anchor Bracket E. Nut, Hex, 5/16
B. Lockwasher, 5/16, Large F. Wing Nut, 5/16
C. Latch, Spring G. Locknut, 5/16
D. Lockwasher, 5/16, Small H. Capscrew, 5/16-18 x 2-1/2
A
C
B
H
D
G
E
F
A
C
F
Initial Turbo Installation
8
Install Belt Cover Plate
1. Attach the belt cover plate (B, Figure 13 & 14) to the
support bracket (E) using a 5/16-18 x 1 capscrew (C),
washer (D) and nylock nut (F).
NOTE: This cover plate must be able to pivot on the
support bracket. Different belt covers are required for
different applications. Refer to Figure 13.
2. Rotate the belt cover until the notch catches the idler
assembly belt cover latch (A, Figure 14). Cover latch
(A) may need to be rotated for proper alignment.
B
A
Figure 14. Install Belt Cover Plate
A. Belt Cover Latch E. Support Bracket
B. Belt Cover Plate F. Nylock Nut, 5/16
C. Capscrew, 5/16-18 x 1
D. Washer, 5/16
50"
44"
Install Turbo Belt
1. Locate the correct drive belt for your installation: 44”
models require drive belt 1705142, 50” models
require drive belt 1707956 (the part number is
stamped on the belt).
2. Loosen the hardware securing the drive pulley belt
guide (B, Figure 15 & 16) and the idler pulley (C)
3. Install the drive belt as shown in Figures 15 & 16.
4. Tighten the hardware securing the drive pulley belt
guide (B) and idler pulley (C). The idler belt guide
should be within 1/16” of the belt.
B
A
D
D
D
D
C
C
B
A
Figure 15. Belt Routing - 44” Models
A. Mounting Bracket
B. Drive Pulley Belt Guide Hardware
C. Idler Pulley Hardware
D. Mounting Bracket Hardware
Figure 16. Belt Routing - 50” Models
A. Mounting Bracket
B. Drive Pulley Belt Guide Hardware
C. Idler Pulley Hardware
D. Mounting Bracket Hardware
WARNING
When the turbo blower assembly is removed from
the mower deck, the deflector MUST be properly
installed.
Install Mounting Bracket
1. See Figures 15 & 16. Locate and remove the two
longer capscrews used to secure the rear of the turbo
housing and idler spring anchor.
2. Install the turbo mounting bracket (A) using the
removed hardware. Note that the bracket is mounted
in two different positions depending on the application.
Figure 13. Belt Cover Plates
A. Belt Cover Plate for 50” Mower
B. Belt Cover Plate for 44” Mower
B
A
E
C
D
F
Belt Cover
Initial Turbo Installation
9
Mower Deck
Arbor Pulley
Mower Deck
Turbo Drive Pulley
Turbo Drive
Pulley
Idler
Pulleys
To Slacken
Belt
CAUTION
Before you begin operating the unit with the
Turbo attached, be certain you have read all of
the safety and operational information on the last
page of this instruction sheet, as well as the
Operator’s Manual for the tractor and any grass
catchers or other collection devices used in
conjunction with this turbo blower.
Install Turbo Drive Belt
1. See Figure 18. Attach the turbo belt to the top RH
pulley on the mower deck. Pull back on the belt tensioning lever to slacken the belt. A view (from right
front of mower) of the belt routing is shown at right.
NOTE: While attaching, it may be necessary to unlatch
the turbo and realign the belt on the pulleys inside the
turbo housing.
2. After the belt is installed, adjust the belt stop (D,
FIgure 11 & 12) so that it is 1/8” away from the backside of the belt.
Figure 18. Turbo Belt Routing
Figure 19. Belt Cover
A. Belt Cover Plate
B. Belt Cover Latch
B
A
Secure Belt Cover
1. The belt cover plate (A, Figure 19) is a safety shield
— after attaching or detaching the turbo unit, it MUST
BE rotated onto the belt cover latch (B).
Install Turbo Blower
1. Install the turbo unit by sliding the turbo pivot rod into
the pivot bracket at the front edge of the mower deck
(A, Figure 17).
2. Tilt the deflector UP (B).
3. Rotate the turbo unit (C) into position on the discharge of the mower deck, and “latch” the slot in the
turbo housing over and onto the anchor bracket at
(D). Tighten the wing nut (E) to secure.
A
B
C
Figure 17. Install Turbo Blower
A. Pivot Bracket D. Anchor Bracket
B. Deflector E. Sleeve Nut
C. Turbo
E
D
FRONT
Initial Counter Balance & Weight
Carrier Installation
10
Figure 1. Counter Balance Installation
Figure 2. Front Weight Carrier Installation
A. Washer, 5/16 E. Clips, Safety
B. Capscrew, 5/16-18 x 1 F. Carrier, Weight
C. Locknut, 5/16-18 G. Holes
D. Rod
B
D
A
L
F
G
H
K
I
J
E
C
M
A. Rear Deck Lift Lever
B. Trunnion (Existing)
C. Hair Pin (Existing)
D. Spacer, Spring (New)
E. Spring (New)
F. Washer (New)
G. Plate, Spring Support (New)
H. Spacer (Existing)
I. Eyebolt (Existing)
J. Washer (Existing)
K. Capscrew (Existing)
L. Nut (Existing)
M. Mower Deck
D
C
F
B
A
A
C
B
B
E
COUNTER BALANCE & WEIGHT
CARRIER INSTALLATION
Counter Balance Installation
1. Remove hair pin (C, Figure 1) from trunnion (B).
Remove trunnion (B) from rear deck lift lever (A).
Mark or measure trunnion position on rear deck lift
lever. Remove trunnion (B) from from eyebolt (I).
2. Remove capscrew (K), washer (J), eyebolt (I), spacer
(H) and nut (L) from mower deck (M).
3. Thread eyebolt (I) through plate (G) as shown.
4. Attach capscrew (K), washer (J), eyebolt (I), spacer
(H), to mower deck (M) securing with nut (L).
5. Slide washer (F), spring (E), and spacer (D) onto
eyebolt (I) as shown.
6. Install trunnion (B) onto eyebolt (I) to position of measurement or mark from step 1.
7. Install trunnion (B) into rear deck lift lever (A) secure
with hair pin (C). Check deck leveling as described in
Operators Manual and make necessary adjustments.
Front Weight Carrier Installation
1. Remove and discard hardware from holes (G, Figure
2).
2. Install carrier (F) as shown securing with 5/16-18 capscrews (B), 5/16 washers (A), and 5/16 locknuts (C).
3. Rod (D) and safety clip (E) are used to secure required
weights.
G
G
E
Initial Hitch &
Tube Installation
11
Figure 1. Install Hitch Plate
A. Hitch Plate E. Upper & Lower
B. Heat Shield Bumper
C. Capscrews, F. Washer
1/2-13 x 1-1/4 G. New Holes, 17/32”
D. Locknuts, 1/2-13 H. Existing RH Holes
Figure 3. Install Back Plate
A. Back Plate and Support C. Hitch Plate
B. Hair Pin D. Rod
B
A
D
C
Figure 2. Install Hitch Assembly
A. Horizontal Support C. Nut, 3/8-16
B. Capscrew, 3/8-16 x 3/4 D. Back Plate
C
B
A
D
D
C
HITCH & TUBE INSTALLATION
Install Hitch Plate and Back Plate
1. Remove and discard right side hardware holding heat
shield (B, Figure 1) to upper and lower bumper (E) to
existing right hand holes (H).
2. Enlarge upper existing hole (H) to 17/32”. Install
hitch plate (A) to upper and lower bumper (E) and
heat shield (B) using upper existing hole (H) and one
1/2-13 x 1-1/4 capscrew and 1/2-13 nut.
3. Square hitch plate (A, Figure 1) to upper & lower
bumper (E) and use as a template to mark and drill
three new holes 17/32” (G)
4. Secure hitch plate (A, Figure 1) to upper & lower
bumper (E) with 1/2-13 x 1-1/4 capscrews (C) washer
(F) and 1/2-13 locknuts (D) as shown.
5. Install the horizontal support (A, Figure 2) on the
back plate (D). Secure with four 3/8-16 x 3/4 cap-
screws (B), 3/8-16 locknuts (C).
6. Set the back plate and support (A, Figure 3) onto pins
of hitch plate (C). Secure with rod (D) and hair pin
(B).
D
E
A
F
G
G
C
B
H
Initial Hitch & Tube Installation
12
Figure 4. Assemble Tubes & Deflector
A
E
C
F
B
A. Upper Tube
B. Middle Tube
C. Lower Tube
D. Nut, Nylock, 10-24 x 3/4
E. Washer
F. Screw, Truss Head, 10-24
G. Holes
H. Clip and Hardware
Assemble Tubes & Deflector
1. Insert the lower tube (C, Figure 4) into middle tube
(B). Secure the tubes as shown in Figure 4 using
#10-24 x 3/4 screws, washer (E) and #10-24 nuts
(D). Insert middle tube (B) into upper tube (A).
Secure the tubes as shown in Figure 4 using #10-24
x 3/4 screws, washer (E) and #10-24 nuts (D).
2. Place upper tube into catcher opening. Secure the
elbow to the turbo using clip (H).
Note: Relocation of clip and hardware (H) to holes (G)
may be necessary to ensure proper fit. Use correct hole
locations to maintain proper tube connections and prevent lower tube from disconnecting from the turbo.
Assemble Catcher Bags
1. See Figure 6. Insert the wire hoop (H) through the
cloth bag (B).
2. Install the clamp (E) and hanger bracket (D). Secure
with two 5/16-18 x 3/4 carriage bolts (C), lockwashers
(G) and nuts (F).
Figure 6. Assemble Catcher Bags
A. Clip E. Clamp
B. Cloth Bag F. Nut
C. 5/16-18 x 3/4 Carriage Bolt G. Lockwasher
D. Hanger Bracket H. Wire Hoop
A
B
C
D
E
F
G
H
D
E
F
D
G
H
Initial Collector
Assembly
13
Figure 7. Install Catcher
A. Nut, #10-32 E. Hinge Pin
B. Handle F. Bags
C. Screw, #10-32 x 1/2 G. Hair Pin Clip
D. Cover
Figure 8. Install Cable
A. Cable C. Washer
B. Support
A
B
C
D
E
F
G
COLLECTOR ASSEMBLY
Install Cover and Bags
1. Hang the bags (F, Figure 7) on the horizontal support.
Note: If desired, the bags can be lined with 30 gallon
trash bags for easy disposal.
2. Install the handle (B) inside the cover. Secure with
two #10-32 x 1/2 screws (C) and nuts (A).
3. Rest the cover assembly (D) on the bags (F).
4. Install the two hinge pins (E) and secure with hair pin
clips (G).
5. Open the cover and fasten cable (A, Figure 8) to support (B). The looped cable end fits over washer (C).
NOTE: Push the hair pin clips all the way on or they will
be bent by the hinge when the cover is opened.
A
B
C
Normal Removal &
Installation
14
NORMAL REMOVAL & INSTALLATION
Removing the Grass Catcher
1. Disconnect the tubes (A, Figure 9) from the turbo and
remove them from the catcher.
2. Remove the hair pin clip (B, Figure 9) and clevis pin
(D) securing the cover (E). Disconnect the cable
(see Figure 8). Remove the cover (E).
3. Remove and empty the bags (C, Figure 9).
4. Warning: Back plate (A) will fall when rod (D) is
removed. Remove the hair pin (B, Figure 10) and
rod (D) while holding back plate (A).
5. Lift back plate & support assembly (A, Figure 10) off
hitch plate (D)
WARNING
OPERATION WITHOUT TURBO & CATCHER
For operation without turbo, the mower deflector
MUST be properly installed in the down position
and retained by the spring latch (See Turbo
Operator’s Manual).
Figure 9. Normal Removal & Installation
A. Tubes
B. Hair Pin Clip
C. Bags
D. Clevis Pin
E. Cover
F. Clip
D
E
C
B
A
F
Figure 10. Install Back Plate
A. Back Plate & Support C. Hitch Plate
B. Hair Pin D. Rod
B
A
D
C
Removing and Reattaching Grass Catcher
15
Installing the Grass Carcher
1. Set the back plate & support (A, Figure 11) on pins of
hitch plate (C). Secure with rod (D) and hair pin (B).
2. Install the bags (C, Figure 12).
3. Install the cover (E, Figure 12). Secure with the clevis pins (F) and hair pin clips (B).
NOTE: Push the hair pin clips all the way on or they will
be bent by the hinge when the cover is opened.
4. Connect the cover cable (Figure 8).
5. Insert the tubes (A, Figure 12) into the catcher and
connect to the turbo. Be sure the clip (F) is secured
over the top of the turbo flange nut.
Figure 11. Install Back Plate
A. Back Plate & Support C. Hitch Plate
B. Hair Pin D. Rod
B
A
D
C
Figure 12. Normal Removal & Installation
A. Tubes
B. Hair Pin Clip
C. Bags
D. Clevis Pin
E. Cover
F. Clip
D
E
C
B
A
F
16
Hardware Identification & Torque Specifications
Common Hardware Types
Hex Head Capscrew
Carriage Bolt
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
second number is present it represent the
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
second number represents the
example, and the final number is the
bolt or screw (in this example 2 inches long).
, meaning the
Nominal size
inside diameter
, or
body diameter
threads per inch
body length
Washer
Lockwasher
Hex Nut
is 1/2 inch; if a
threads per inch
is 1/2 inch; the
(16 in this
of the
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
Nut, 1/2”
Inside
Diameter
1
1/4 3/4
1/2
Screw, 1/2 x 2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Body
Diameter
Body
Length
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
Size Of
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32
8-36
10-24
10-32
1/4-20
1/4-28
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
No
Marks
SAE Grade 2 SAE Grade 5 SAE Grade 8
in/lbs in/lbs
19
20
27
31
66
76
2.1
2.3
3.1
3.5
7.6 8 10.9 12 16.3
8.6 10 13.6 14 19.0
30
31
43
49
NOTES
3.4
3.5
4.9
5.5
in/lbs
41
43
60
68
4.6
4.9
6.8
7.7
Wrench & Fastener Size Guide
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16
5/16” Bolt or Nut
Wrench—1/2”
3/8
3/8” Bolt or Nut
Wrench—9/16”
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”
Loading...