Page 1
Parts Manual
2005 Rapid
Series Lawn Tractor & Mower Deck
17HP Tractors
Mfg. No. Description
1694376 2005 Rapid, 17HP Hydro (CE)
Mower Decks
Mfg. No. Description
1694377 40" Mower Deck (CE)
04/2003
Rev.
TP 400-3825-00-RG-UV
Page 2
Page 3
Table Of Content
s
TRACTOR / MOWER DECK COMPONENTS PAGES
Frame Group .........................................................................................................................
Steering Group ......................................................................................................................
Engine & Electric Clutch - 17HP Briggs & Stratton ................................................................
Transmission Group ..............................................................................................................
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle ..............................................
Controls Group ......................................................................................................................
Electrical Group .....................................................................................................................
Hood, Dash & Fuel Tank Group ............................................................................................
Seat & Seat Deck Group .......................................................................................................
Wheels & Tires Group ...........................................................................................................
Decals Group - Safety & Common ........................................................................................
40" Mower Deck - Belt, Idler Arm & Hitch Group ...................................................................
40" Mower Deck - Height Adjustment & Roller Bar ...............................................................
40" Mower Deck - Housing, Arbors & Blades ........................................................................
12
14
20
22
24
26
28
30
32
34
38
Torque Specification Chart ..................................................................... Inside Back Cover
4
6
8
Page 4
Frame Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
3
3
1
985858
7
8
5
6
4
2
18
21
18
17
16
20
21
18
19
Insert Must
Face Out
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
15
14
12
13
9
10
9
11
10
12
10
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
4
TP 400-3825-00-RG-UV
Page 5
Frame Group
PART NO. DESCRIPTIONREF NO QTY.
1 1723077 1 FRAME ASSEMBLY
2 1715015 1 PLUG, Hole
3 1714418 1 PAD, Footrest RH
4 1714417 1 PAD, Footrest LH
5 1704351 12 FASTENER, Panel
6 1935255 4 NUT, Speed 5/16-18
7 1930591 4 SCREW, Hex Head Flange Lock, 5/16-18 x 3/4
8 1723021 1 WRAPPER ASSEMBLY, Hydro
9 1920328 2 CAPSCREW, Hex Head, 1/2-13 x 1-1/2
10 1918431 3 WASHER, 1/2
11 1709235 1 SPACER
12 1930644 2 NUT, Hex , 1/2-13
13 1721013 1 CARRIER ASSEMBLY, Hydro
14 1717286 1 SPACER
15 1717424 1 BAR, Torsion
16 960641 1 NUT, Hex Lock Aluminum Insert, 3/8-16
17 1924356 1 WASHER, 3/8
18 176440 6 BUSHING, 3/4, Nylon
19 1719868 1 SPACER
20 1719869 1 HITCH, Hook "J"
21 1960614 1 CAPSCREW, Hex Head, 3/8-16 x 3
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
5
TP 400-3825-00-RG-UV
Page 6
Steering Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
14
27
985576B
1
19
7
29
28
7
3
4
5
6
8
2
16
26
14
21
22
7
18
20
17
25
24
15
7
16
18
13
17
9
10
11
12
13
23
14
Note: Se e
Wheels & Tires
Group
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
6
TP 400-3825-00-RG-UV
Page 7
Steering Group
PART NO. DESCRIPTIONREF NO QTY.
1 1713841 1 STEERING WHEEL ASSEMBLY, (Includes Ref. No. 2)
2 1714097 1 CAP, Steering Wheel
3 1714400 1 TUBE, Flex
4 1960540 1 PIN, Spring, 5/16 x 2-1/2
5 1719472 1 SHAFT ASSEMBLY, Steering
6 1931350 2 CARRIAGE BOLT, 3/8-16 x 1
7 1960114 4 WASHER, 3/4
8 1928352 2 NUT, Hex Flange Whiz Lock, 3/8-16
9 1920415 1 CAPSCREW, Hex Head 3/8-16 x 1-1/4
10 1922611 1 WASHER, 3/8
11 1713375 1 STEERING GEAR ASSEMBLY
12 1713469 1 DRAG LINK
13 1930645 3 NUT, Hex Flange Lock, 3/8-16
14 1611710 4 KLIPRING
15 1721472 1 ARM, Steering, LH
16 1960160 2 WASHER, 3/4
17 1721542 2 SPINDLE ASSEMBLY
18 1713791 2 SPACER
19 1919314 1 PIN, Cotter, 3/16 x 1-1/4
20 1713454 1 TIE ROD
21 1721473 1 ARM, Steering, RH
22 1960268 2 CARRIAGE BOLT, 3/8-16 x 1-1/4
23 1931335 1 CARRIAGE BOLT, 5/16-18 x 1
24 1710437 1 SPACER
25 1935048 1 NUT, Hex Flange Lock, 5/16-18
26 1664847 2 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 3/4
27 1666001 1 BUSHING
28 176440 1 BUSHING
29 1703508 1 PLATE, Steering, Mounting
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
7
TP 400-3825-00-RG-UV
Page 8
Engine & Electric Clutch - 17HP Briggs & Stratton
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
44
39
43
47
E985943
3
2
4
18
5
7
6
8
9
1
45
46
12
16
15
12
16
13
RH Front
LH Front & LH Rear
14
10
11
17
RH Rear
42
19
37
40
39
41
38
36
35
34
33
32
31
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
20
21
30
25
23
22
29
24
25
26
28
27
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
8
TP 400-3825-00-RG-UV
Page 9
Engine & Electric Clutch - 17HP Briggs & Stratton
PART NO. DESCRIPTIONREF NO QTY.
1 1708405 1 VALVE, Shut Off
2 920427 1 LOCKWASHER, External Tooth 3/8
3 916950 1 NUT, Hex 3/8-16
4 1723212 1 SEAL, Foam
5 * 1 ENGINE, 17HP B&S INTEK, Domestic, Model 31F770, Type 0110
5 * 1 ENGINE, 17HP B&S INTEK, Export, Model 31F777, Type 0111
6 173206 1 FUEL FILTER
7 960112 2 CLAMP
8 1718678 1 HOSE, 12" Long
9 1715897 1 KNOB, Slot
10 1960498 2 CAPSCREW, Hex 1/4-14 x 5/8
11 1707388 1 CONTROL, Throttle Cable
12 1704419 2 STOP, Belt
13 1930598 3 CAPSCREW, Hex Head Taptite, 3/8-16 x 1-1/2
14 905100 1 KEY
15 1723497 1 PULLEY & HUB ASSEMBLY, Engine
16 1933263 2 WASHER
17 960361 1 CAPSCREW, Hex Head Taptite, 3/8-16 x 2
18 1723213 1 SEAL, Foam
19 1708537 1 SLEEVE, Clutch Anchor
20 1717664 1 CLUTCH, Electric, OGURA
21 1708264 1 WASHER, Hex, Special
22 1918199 1 LOCKWASHER, 7/16
23 960631 1 CAPSCREW, Hex Head, 7/16-20 x 3
24 1701011 1 TIE, Wire
25 1935255 4 NUT, Speed 5/16-18
26 1717993 1 DUCT, Muffler, Lower
27 1930595 2 CAPSCREW, Hex Head Flange Lock, 5/16-18 x 1-1/4
28 1705248 2 PIVOT
29 1705249 2 SPACER
30 1723337 1 INSULATION, LH (Export)
31 1921333 1 CAPSCREW, Hex Head, 5/16-18 x 1
32 1919381 1 WASHER, 5/16
33 1930591 2 CAPSCREW, Hex Head Flange Lock 5/16-18 x 3/4
34 1723338 1 INSULATION, RH (Export)
35 1723336 1 INSULATION, Foam, 6 x 11-3/8 (Export)
36 1715006 1 DUCT, Muffler Upper, Domestic
36 1723086 1 DUCT, Muffler Upper, Export
37 1715509 1 STRAP, Torque (Export)
38 1919326 1 WASHER, 5/16
Footnotes
* See your local Briggs & Stratton dealer / distributor for parts and service.
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
9
TP 400-3825-00-RG-UV
Page 10
Engine & Electric Clutch - 17HP Briggs & Stratton
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
44
39
43
47
E985943
3
2
4
18
5
7
6
8
9
1
45
46
12
16
15
12
16
13
RH Front
LH Front & LH Rear
14
10
11
17
RH Rear
42
19
37
40
39
41
38
36
35
34
33
32
31
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
20
21
30
25
23
22
29
24
25
26
28
27
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
10
TP 400-3825-00-RG-UV
Page 11
Engine & Electric Clutch - 17HP Briggs & Stratton
PART NO. DESCRIPTIONREF NO QTY.
39 1917356 2 LOCKWASHER, 5/16 (Export)
40 1917372 1 NUT, Hex 5/16-18 (Export)
41 1924856 4 CAPSCREW, Hex Head Taptite, 5/16-18 x 1/2
42 1927428 2 CAPSCREW, Hex Head Taptite,1/4-20 x 3/8
43 1717429 1 MUFFLER, Domestic
43 1723408 1 MUFFLER, Export
44 1936228 2 CAPSCREW, Hex Head, 5/16-18 x 3/4
45 1720567 1 PIPE, Exhaust
46 1650670 1 GASKET, Ehaust
47 1720204 1 WIRE ASSEMBLY, B&S, Domestic
47 1723275 1 WIRE ASSEMBLY, B&S, Export
Footnotes
* See your local Briggs & Stratton dealer / distributor for parts and service.
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
11
TP 400-3825-00-RG-UV
Page 12
Transmission Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
3
2
1
4
28
4
4
8
7
28
27
4
19
985852
6
5
7
8
4
See Frame Group
10
13
35
11
26
9
12
14
See Engine
Group
Part of
frame.
18
31
30
See Frame Group
29
23
32
16
17
15
19
20
1
2
1
5
23
24
21
22
See Wheels & Tires in
Miscellaneous Group.
21
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
12
TP 400-3825-00-RG-UV
Page 13
Transmission Group
PART NO. DESCRIPTIONREF NO QTY.
1 1931335 1 CARRIAGE BOLT, 5/16-18 x 1
2 1721097 1 ROD, Hydro Control
3 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18
4 1919326 5 WASHER, 5/16
5 1960541 1 CAPSCREW, Hex Head Taptite, 5/16-18 x 3/4
6 1721007 1 STOP, Belt
7 1917372 2 NUT, Hex 5/16-18
8 1917356 2 LOCKWASHER, 5/16
9 1724313 1 PULLEY
10 1960585 1 CAPSCREW, Hex Head Flange Lock, 5/16-18 x 1-3/4
11 1724315 1 LOCKWASHER
12 1724312 1 SPLINE COLLAR
13 1721130 1 V-BELT, Drive
14 1724314 1 FAN
15 1718076 3 "E" RING
16 1721005 1 ROD, Hydro Bypass
17 1918447 1 PIN, Cotter
18 1686876 1 TRANSMISSION ASSEMBLY
19 1931277 4 NUT, Hex Flange, 5/16-18
20 1717749 2 KEY, 3/16 x 2
21 960202 4 WASHER, 3/4
22 1717451 6 SPACER
23 1960586 4 CAPSCREW, Hex Head, 5/16-18 x 2-1/2
24 1717427 1 ANCHOR, Torsion Bar, LH
25 960551 4 CAPSCREW, Hex Washer Head Taptite, 5/16-18 x 2-1/2
26 1921333 1 CAPSCREW, Hex Head, 5/16-18 x 1
27 1921977 1 CAPSCREW, Hex Head, 5/16-18 x 1-1/4
28 1703900 2 SPACER
29 1717428 1 ANCHOR, Torsion Bar, RH
30 1918451 2 PIN, Cotter
31 1720998 1 ROD, Brake
32 1960585 1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
13
TP 400-3825-00-RG-UV
Page 14
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
THICKER PLATE
64
1721020
1
2
3
4
5
81
82
80
79
78
21
8383
84
20
76
7470
69
68
67
66
65
77
7475
73
74
72
71
61
59
57
63
60
62
58
56
55
54
66
56
55
54
6
7
8
10
11
12
9
13
14
15
17
23
18
16
19
20
21
17
22
24
23
25
27
48
43
44
45
53
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
30
27
29
PLATE OF SMALLER INNER DIA.
SHOULD CONTACT PISTONS.
45
32
33
34
SEAL SIDE; OUTER
38
35
36
31
41
37
40
39
37
44
43
26
27
28
47
46
42
52
49
50
51
49
50
51
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
14
TP 400-3825-00-RG-UV
Page 15
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle
PART NO. DESCRIPTIONREF NO QTY.
1 1724316 1 SNAP RING
2 1724313 1 PULLEY D
3 1724315 1 LOCK WASHER
4 1724312 2 SPLINE COLLAR
5 1724314 1 FAN
6 1718076 3 RING E 15
7 1724291 1 PUMP SHAFT
8 1724283 1 SEAL TC 153507
9 1708650 1 RING, SNAP C 35
10 1718083 1 BEARING 6202C3
11 1724282 1 SEALING CAP 30
12 1724279 2 K50 MAGNET
13 1724280 1 HOLDER MAGNET
14 1718052 1 VENT VALVE 15
15 1724310 1 PIN 5*32
16 1724306 1 ARM BRAKE
17 1724311 2 PIN SPRING 4*16
18 1708690 2 O-RING 1A P12
19 1724308 1 RETURN SPRING B
20 1720814 2 BUSHING 19.05
21 1718111 2 SEAL 19*32*8
22 1724307 1 SHAFT BRAKE
23 1724305 1 SHOE BRAKE
24 1724309 1 ACTUATOR BRAKE
25 1724351 1 CENTER CASE E CMP
26 1718070 1 PIN 3*9.8
27 1720805 3 BOLT 10*75
28 1718071 1 FILTER K50 SNP
29 1718084 1 WASHER 12*24*1
30 1724292 1 CYLINDER BLOCK
31 1718078 1 BEARING 51106
32 1718077 1 HOUSING
33 1724293 1 SHAFT MOTOR
34 1708672 1 RING, SNAP S 15
35 1718083 1 BEARING 6202C3U
36 1724294 1 MOTOR GEAR
37 1720439 2 WASHER 12*32*3.2
38 1724301 1 REDUCTION GEAR
39 1724299 1 COLLAR, FINAL P
40 1724302 1 FINAL PINION
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
15
TP 400-3825-00-RG-UV
Page 16
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
THICKER PLATE
64
1721020
1
2
3
4
5
81
82
80
79
78
21
8383
84
20
76
7470
69
68
67
66
65
77
7475
73
74
72
71
61
59
57
63
60
62
58
56
55
54
66
56
55
54
6
7
8
10
11
12
9
13
14
15
17
23
18
16
19
20
21
17
22
24
23
25
27
48
43
44
45
53
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
30
27
29
PLATE OF SMALLER INNER DIA.
SHOULD CONTACT PISTONS.
45
32
33
34
SEAL SIDE; OUTER
38
35
36
31
41
37
40
39
37
44
43
26
27
28
47
46
42
52
49
50
51
49
50
51
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
16
TP 400-3825-00-RG-UV
Page 17
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle
PART NO. DESCRIPTIONREF NO QTY.
41 1724300 1 REDUCTION SHAFT
42 1724303 1 AXLE SHAFT L
43 1718110 2 BUSHING
44 1718112 2 THRUST WASHER
45 1718113 2 RING 17
46 1724297 2 DIFF PINION
47 1724298 1 FINAL GEAR
48 1724304 1 AXLE SHAFT R
49 1707789 14 SCREW, TAPPING 8*30
50 1724323 2 WASHER, SEAL 8
51 1724324 2 SCREW, CAP 8*12
52 1724284 2 TAPPING SCREW 8*55
53 1727278 1 LOWER HOUSING
54 1724287 2 IDS SPRING
55 1724288 2 BALL 3/16
56 1724286 2 IDS VALVE 1.0
57 1724311 1 SPRING PIN 6.0A*36
58 1724349 1 COTTER PIN
59 1724343 1 CONTROL SHAFT
60 1724345 1 SP (TORSION
61 1724346 1 CONTROL ARM E
62 1724348 1 JERKY PLATE
63 1724344 1 FULCRUM (ECCENTRICIT
64 1724289 1 CYLINDER BLOCK
65 1724290 1 SPRING (PUMP)
66 1718088 1 THRUST PLATE
67 1718086 1 BEARING K81105
68 1718087 1 THRUST PLATE
69 1720426 1 SWASH PLATE CMP.
70 1718089 2 THRUST METAL
71 1718061 1 RING 10
72 1708684 1 SPRING 25
73 1724318 1 OIL SEAL 16*22*03
74 1724317 1 UPPER HOUSING
75 1718098 2 O-RING 1A P14
76 1708689 1 WASHER, 12
77 1708692 1 NUT 12
78 1718100 1 PIN, ROLL 6*40
79 1724347 1 CONTROL LEVER
80 1720418 1 LEVER BYPASS
81 1720421 1 PIN 3.0A*20
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
17
TP 400-3825-00-RG-UV
Page 18
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
THICKER PLATE
64
1721020
1
2
3
4
5
81
82
80
79
78
21
8383
84
20
76
7470
69
68
67
66
65
77
7475
73
74
72
71
61
59
57
63
60
62
58
56
55
54
66
56
55
54
6
7
8
10
11
12
9
13
14
15
17
23
18
16
19
20
21
17
22
24
23
25
27
48
43
44
45
53
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
30
27
29
PLATE OF SMALLER INNER DIA.
SHOULD CONTACT PISTONS.
45
32
33
34
SEAL SIDE; OUTER
38
35
36
31
41
37
40
39
37
44
43
26
27
28
47
46
42
52
49
50
51
49
50
51
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
18
TP 400-3825-00-RG-UV
Page 19
Transmission SERVICE PARTS - Tuff Torq K-46Z Transaxle
PART NO. DESCRIPTIONREF NO QTY.
82 1707839 1 SPRING PIN 3*16
83 1708691 2 O-RING 1A P10A
84 1724281 1 SHAFT (BYPASS)
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
19
TP 400-3825-00-RG-UV
Page 20
Controls Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
32
33
31
34
26
29
28
27
2415
26
6
27
30
25
985945
1
2
Connect to Top
3
of Frame
4
5
6
7
8
9
10
See
Transmission
Group
11
Part of
Frame
19
24
23
Connect to
Lanced Notch
in Top of Frame
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
22
19
19
20
21
12
18
17
16
13
14
15
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
20
TP 400-3825-00-RG-UV
Page 21
Controls Group
PART NO. DESCRIPTIONREF NO QTY.
1 1713855 1 KNOB
2 1714385 1 ROD, Parking Brake
3 165068 1 SPRING, Extension
4 1717439 1 LEVER, Parking
5 1921319 1 WASHER, 1/4
6 1663114 2 BUSHING, 21/32, Nylon
7 1931355 1 CARRIAGE BOLT, 3/8-16 x 2-1/4
8 1717438 1 ARM, Idler
9 1721133 1 PULLEY, Backside, Idler, 3-1/4 OD
10 1719590 1 SPRING, Extension
11 1717440 1 ROD, Brake
12 1717728 1 GUIDE BELT & STUD ASSEMBLY
13 1703900 1 SPACER
14 1935048 1 NUT, Hex Flange, 5/16-18
15 1919438 5 NUT, Hex Lock, 5/16-18
16 1919381 1 WASHER, 5/16
17 1705249 1 SPACER
18 1708360 1 SPRING, Compression
19 1924940 3 WASHER, 5/16
20 1667811 1 SPACER
21 1721276 1 STOP, Belt
22 1928352 1 NUT, Hex Head Whiz Lock, 3/8-16
23 1921971 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4
24 1916965 1 LOCKWASHER, 3/8
25 1721134 1 PULLEY, Idler, 3 OD
26 1918451 2 PIN, Cotter, 1/8 X 3/4
27 1919326 2 WASHER, 5/16
28 1931333 4 CARRIAGE BOLT, 5/16-18 x 3/4
29 1713784 1 CLAMP
30 1717115 1 ROD, Clutch
31 1715835 1 PAD, Reverse Pedal
32 1704849 1 PAD, Brake Pedal
33 1720004 1 FOOT PEDAL & BRAKE ARM ASSEMBLY
34 1721577 1 PAD, Forward Pedal
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
21
TP 400-3825-00-RG-UV
Page 22
Electrical Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
4
To Starter
Motor
3
2
1
To Circuit
Breaker (Red)
85588AA
13
14
16
15
17
18
20
19
24
12
25
11
10
9
5
8
7
6
28
27
13
14
26
To Engine
Ground Bolt
25
24
32
29
22
21
23
To Solenoid
(Yellow & Black)
To Negative
Battery Post
To Engine
Ground Connection
30
To Engine
Harness Plug
To Engine
Harness Plug
Briggs Only
31
37
33
34
To PTO Clutch
35
36
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
22
TP 400-3825-00-RG-UV
Page 23
Electrical Group
PART NO. DESCRIPTIONREF NO QTY.
1 1703799 1 SWITCH, Headlights
2 1722887 1 SWITCH, PTO, Push/Pull
3 1703484 1 CABLE, # 6, 42-1/2" Long
4 122023 1 COVER, Terminal
5 1686734 1 SWITCH ASSEMBLY, Ignition, 6 Pin (Includes Ref. Nos. 6, 7, 8, 27, & 28)
6 1960547 1 LOCKWASHER, Internal Tooth 5/8
7 101025 1 WASHER, 5/8
8 1717549 1 NUT, Hex Flange, 5/8-32
9 1665237 1 WIRE, 12GA, 5.9 Long Red
10 1665238 1 BREAKER, Circuit 12Volt, 20Amps w/Tab
11 1927429 2 CAPSCREW, Hex Washer Head Taptite, 1/4 x 5/8
12 1686982 1 SOLENOID, 4 Pole 12 Volt DC
13 920426 2 LOCKWASHER, External Tooth, 5/16
14 1920263 2 NUT, Hex, 5/16-24
15 1716549 1 CABLE, # 6, 10" Long
16 1677296 1 BOOT, Insulator Battery Terminal
17 921319 2 WASHER, 1/4
18 923341 2 CAPSCREW, Hex Head, 1/4 x 3/4
19 1921332 1 CAPSCREW, Hex Head, 5/16-18 x 3/4
20 1919326 1 WASHER, 5/16
21 1723048 1 ROD, Battery Hold Down
22 1919438 1 NUT, Hex Lock ESNA, 5/16-18
23 1685215 1 BATTERY, 12 Volt
24 916964 2 LOCKWASHER, 1/4
25 916622 2 NUT, Hex, 1/4-20
26 1723109 1 CABLE,# 6, 52-1/2" Long
27 1717163 1 KEYS, Ignition
28 1717550 1 COVER, Ignition Switch
29 1724875 1 WIRE HARNESS
30 1715014 1 SHRINK TUBE
31 1715010 1 WIRE ASSEMBLY, 16GA, 16" Long, Black/Tan
32 1718981 1 SWITCH, Seat
33 1720411 1 SWITCH, Push, Black
34 1720401 1 SWITCH, Push, Grey
35 934683 2 CLIP, Wire
36 1701011 2 TIE, Wire
37 1720204 1 WIRE ASSEMBLY
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
23
TP 400-3825-00-RG-UV
Page 24
Hood, Dash & Fuel Tank Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
3
2
1
33
985713B
6
4
5
12
10
9
9 10
11
7
8
13
14
32
Screws Into
Heat Shield
Ref. #17 of
Engine Group
29
31
28
30
27
10
25
26
22
24
10
22
20
15
16
Panel, Left Side
34
Panel, Right Side
17
18
19
23
22
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
24
21
TP 400-3825-00-RG-UV
Page 25
Hood, Dash & Fuel Tank Group
PART NO. DESCRIPTIONREF NO QTY.
1 1674231 1 FITTING, Fuel
2 1654930 1 GROMMET, Fuel Fitting
3 1714472 1 FUEL TANK
4 1714020 1 CAP, Fuel Tank
5 1715044 1 STRAP
6 1704351 1 FASTENER, Plastic, Ratchet
7 1919438 2 NUT, Hex Nylon Lock, 5/16-18
8 1960353 A/R WASHER, 1/4
9 1960368 4 PAL NUT, 1/4-20
10 1960295 11 CAPSCREW, Hex Head Whiz Lock, 1/4-20 x 5/8
11 1719945 1 BULKHEAD ASSEMBLY
12 1925003 4 CAPSCREW, Taptite Hex Washer Head, 1/4-20 x 1/2
13 1715495 1 GROMMET, Strip
14 1714769 1 DASHBOARD
15 172434 2 CLIP
16 1714350 1 PANEL, Side, LH, Orange
16 41714350 1 PANEL, Side, LH, Red
17 1714353 1 LIGHT BAR ASSEMBLY (Includes Ref. Nos. 18, 19, 20 & 21)
18 1714787 2 SOCKET, Bulb
19 1714786 1 BEZEL
20 1677371 2 BULB, #1156
21 1714785 1 LENS
22 1920397 10 NUT, Hex, Nylon Lock, 1/4-20
23 1714352 1 GRILLE, Orange
23 41714352 1 GRILLE, Red
24 1921319 2 WASHER, Plain, 1/4
25 1704626 2 SPACER, Plastic, Hood Pivot
26 1704628 2 CLIP, Pivot Spacer Retaining
27 1714875 2 HINGE, Hood
28 1710703 2 SPACER
29 1922837 2 CAPSCREW, Hex Head, 1/4-20 x 1-1/2
30 1930595 2 CAPSCREW, Hex Head Whiz Lock, 5/16-18 x 1-1/4
31 1705248 2 SPACER, Steel, Hood Pivot, Grooved
32 1705249 2 SPACER, Steel, Hood Pivot
33 1714349 1 HOOD, Orange (15 & 16 HP Only)
33 1719483 1 HOOD, Orange (17 HP Only)
33 41714349 1 HOOD, Red (15 & 16 HP Only)
33 41719483 1 HOOD, Red (17 HP Only)
34 1714351 1 PANEL, Side, RH, Orange
34 41714351 1 PANEL, Side, RH, Red
Footnotes
*As required on early style units only. If tractor is not equipped with washers (25), do not add them when performing service.
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
25
TP 400-3825-00-RG-UV
Page 26
Seat & Seat Deck Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
25
23
24
20
985578
1
2
2
3
5
3
4
4
7
6
6
8
9
21
16
22
18
17
19
12
10
12
11
12
13
14
15
9
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
26
TP 400-3825-00-RG-UV
Page 27
Seat & Seat Deck Group
PART NO. DESCRIPTIONREF NO QTY.
1 1721702 1 * SEAT ASSEMBLY
2 1919438 2 NUT, Hex Nylon Lock, 5/16-18
3 1709256 2 WASHER,5/16
4 1704728 2 SPRING, Seat
5 1715768 1 PLATE, Spring Support
6 1931333 2 CARRIAGE BOLT, 5/16-18 x 3/4
7 1718981 1 SWITCH, Seat, Used with Seat P/N 1721702
8 1931648 4 CAPSCREW, Hex Head Whiz Lock, 5/16-18 x 1/2
9 1931277 4 NUT, Hex Flange Whiz-Lock, 5/16-18
10 1935255 2 SPEED NUT, Tinnerman Lug Type, 5/16-18
11 1718985 1 PAN, Seat
12 1930591 8 CAPSCREW, Hex Head Whiz Lock, 5/16-18 x 3/4
13 1713794 2 STOP, Rubber Seat
14 1713758 2 BAR, Seat Pivot
15 1714317 1 SEAT DECK, Orange
15 41714317 1 SEAT DECK, Red
16 1714542 1 CONTROL POD, Hydro
17 1960086 3 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 5/8
18 1708008 1 CLAMP, Wire (Middle Bolt Only)
19 1919326 3 WASHER, 5/16
20 1666697 3 SPACER
21 1715047 1 CAP, Seat Adjust
22 1713597 1 LEVER, Seat Latch
23 159106 1 SPRING, Extension
24 1714318 2 SIDE PANEL, Seat Slide
25 1713595 1 SLIDE, Seat
Footnotes
Optional arm rest kit avaliable under Part Number 1686796.
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
27
TP 400-3825-00-RG-UV
Page 28
Wheels & Tires Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
1
W985874
REAR WHEELS & TIRES
2
3
4
6
55
e
e
S
n
o
i
s
i
s
m
s
n
a
r
T
p
u
r
o
G
9
107
8
10
11
12
FRONT WHEELS & TIRES
12
55
13
14
6
R
s
A
e
d
i
r
u
q
e
7
8
9
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
28
TP 400-3825-00-RG-UV
Page 29
Wheels & Tires Group
PART NO. DESCRIPTIONREF NO QTY.
1 1717749 2 KEY, 3/16 x 2
2 1716131 2 WHEEL & TIRE ASSEMBLY
3 1716133 2 TIRE, 20 x 8 - 8 Super Trac II
4 1716132 2 WHEEL, 7 x 8
5 172353 4 VALVE STEM & CAP ASSEMBLY
6 960202 4 WASHER
7 1960160 4 WASHER
8 927794 4 "E" - RING
9 1722675 4 CAP, Hub
10 1716129 2 WHEEL & TIRE ASSEMBLY (Includes Ref. Nos. 5, 11, 12, 13 & 14)
11 1715032 2 WHEEL & BUSHINGS ASSEMBLY (Includes Ref. No. 12)
12 1713167 2 BEARING
13 1716130 2 TIRE, 15 X 6.5 - 6 Super Trac II
14 1664090 2 TUBE, Tire
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
29
TP 400-3825-00-RG-UV
Page 30
Decals Group - Safety & Common
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
1
6
C985874A
3
2
1
5
4
7
2
8
11
9
14
12
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
10
6
STOP ENGINE.
PUSH
MOTOR STOP PEN.
8
9
MOTOR ANH ALTEN.
STOP MOT OR.
ARRETER LE MOTEUR.
FERMARE MOTORE.
DO NOT TOW!
NIET SLEPEN!
NICH T SCH LEP PEN!
IKKE BUGSERE!
NE PAS REMORQUE R!
NON TRAINAR E!
DUWEN
SCHIEBEN
SKUB
POUSSER
SPINGERE
DRIVE
RIJDEN
FAHREN
KØR
CONDUIRE
GUIDARE
171963 5
9
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
30
TP 400-3825-00-RG-UV
Page 31
Decals Group - Safety & Common
PART NO. DESCRIPTIONREF NO QTY.
1 1722554 1 DECAL, Belts & Mower Blades
2 1722561 1 DECAL, Operating Instructions (CE)
3 1722550 1 DECAL, 17HP
4 * 1 DECAL, Patent (Not Serviced)
5 * 1 DECAL, CE & Serial Number Export (Not Serviced)
6 1708927 1 DECAL, USA Logo
7 1725072 2 DECAL, Touch Up Paint, Red
8 1719635 1 DECAL, Transmission Relese Valve, Hydros Only
9 1720389 2 DECAL, Danger Rotating Cutting Blade, 40" (CE)
10 1722771 1 DECAL, Free Floating Mower
11 1720919 1 DECAL, Height of Cut
12 1722788 1 DECAL, 40"
13 1723071 1 DECAL, Engine,17HP B&S INTEK (Not Shown)
14 * 1 DECAL, OPEI (Not Serviced)
Footnotes
Not a service part.
The above parts group applies to the following Mfg. Nos.:
1694376 - 2005 Rapid
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
31
TP 400-3825-00-RG-UV
Page 32
40" Mower Deck - Belt, Idler Arm & Hitch Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
35
31
10
30
29
10
33
32
To Slot "B"
11
34
10 30
85688AA
1
2
3
2
4
6
9
10
12
14
5
7
8
To Slot "A"
28
27
24
23
26
Insert Must
Face Out
22
Slot "A"
25
21
2
19
20
18
17
Slot "B"
29
13
17
2
36
15
16
17
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
32
TP 400-3825-00-RG-UV
Page 33
40" Mower Deck - Belt, Idler Arm & Hitch Group
PART NO. DESCRIPTIONREF NO QTY.
1 1919439 1 NUT, Hex Lock Esna Light, 3/8-16
2 1924940 5 WASHER, 3/8
3 1721710 1 PULLEY, Idler
4 1721532 1 V-BELT, Arbor Drive
5 1722175 1 BELT GUIDE
6 1960534 2 WASHER, 3/8
7 1720598 1 ARM ASSEMBLY, Idler with Bushings & Fitting
8 1960315 1 CARRIAGE BOLT, 3/8-16 x 2
9 1928957 1 CAPSCREW, Hex Head, 3/8-16 x 2-3/4 G8
10 1922755 6 WASHER, 3/8
11 1715435 1 SPRING, Extension, Idler Arm
12 1657242 1 SPACER, Hardened
13 1719965 1 GRIP, Black Vinyl for Handle
14 1922130 1 CAPSCREW, Hex Head, 3/8-16 x 2-1/4
15 1723952 1 PULLEY
16 1667812 1 SPACER
17 1928352 4 NUT, Hex Flange Whiz Lock, Large, 3/8-16
18 1921969 2 CAPSCREW, Hex Head, 3/8-16 x 1-1/2
19 172329 2 SPACER
20 1713578 1 ROD, Mower Hitch
21 156302 1 SPRING, Extension, Hitch Release
22 1715759 1 ROD, Latch
23 1720044 1 HITCH, Mower
24 1960519 1 NUT, Push
25 960641 2 NUT, Hex Lock ALUM Insert, 3/8-16
26 1721425 1 WASHER & NUT ASSEMBLY, 3/8 x 1-1/2
27 1674671 1 SPRING, Extension
28 1719923 1 ARM, Idler
29 1719221 2 HUB
30 1719562 2 PULLEY, Idler, 22 Teeth
31 1923701 1 CAPSCREW, Hex Head, 3/8-16 x 2
32 1930601 1 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 1/2
33 1666697 1 SPACER
34 1921971 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4
35 1721118 1 BELT, Timing
36 1722182 1 BELT GUIDE
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
33
TP 400-3825-00-RG-UV
Page 34
40" Mower Deck - Height Adjustment & Roller Bar
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Apply Locktite
61
380 in hole prior
60
59
62
58
57
56
55
54
52
51
50
49
48
To "A"
43
42
19
to assembly.
29
28
2
16
21
53
47
63
46
17
85689AA
2
45
18
63
3
4
7
10
5
7
6
8
7
44
40
11
14
30
29
23
12
13
To Handle
Assy
24
32
33
34
26
23
31
3
19
20
22
45
44
41
7
40
39
3
2
16
31
38
15
25
27
23
2
1
1
9
From
"A"
38
Insert Must
Face Out
37
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
34
36
28
2
16
5
7
35
TP 400-3825-00-RG-UV
Page 35
40" Mower Deck - Height Adjustment & Roller Bar
PART NO. DESCRIPTIONREF NO QTY.
1 1921333 2 CAPSCREW, Hex Head, 5/16-18 x 1
2 1960044 5 WASHER, 5/16
3 1960236 4 SPACER
4 1720693 1 SHAFT & BAR ASSEMBLY, 40" Roller
5 1717675 4 ROLLER
6 1668513 6 ROLLER
7 1924366 14 WASHER, 5/8
8 1676652 1 SPACER
9 1714529 1 ROD, Transport
10 1960074 1 CLIP, Hair Pin
11 1720372 1 U-BRACKET
12 1923362 2 NUT, Hex Centerlock 5/16-18
13 1710703 2 SPACER
14 1960044 4 WASHER, 5/16
15 1921977 2 CAPSCREW, Hex Head, 5/16-18 x 1-1/4
16 1960373 3 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 1
17 1666697 1 SPACER
18 108512 1 PIVOT, 3/4 Hex
19 1924940 2 WASHER, 3/8
20 1918447 1 PIN, Cotter
21 1723409 1 BRACKET, Adjusting
22 1931335 2 CARRIAGE BOLT, 5/16-18 x 1
23 960643 5 NUT, Hex Flange Lock, 5/16-18
24 1960223 1 CARRIAGE BOLT, 5/16-18 x 1-1/4
25 1717145 1 ARM, 1 1/4
26 1714879 1 CAM, Eccentric 1 1/8 Hex
27 1924874 1 WASHER, 5/16
28 960643 5 NUT, Hex Collar Lock, 5/16-18
29 1704351 2 FASTENER, Panel
30 1720692 1 SHAFT ASSEMBLY, Rocker
31 1960594 3 CAPSCREW, Hex Head, Taptite 5/16-18 x 7/8
32 1721852 1 UPSTOP
33 1664847 8 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 3/4
34 1665374 3 STRAP, Roller Support
35 1960520 1 NUT, Push 5/8
36 1719846 1 BAR, Roller
37 960641 1 NUT, Hex Aluminum Lock, 3/8-16
38 1706644 1 SPACER
39 1930651 1 NUT, Hex Centerlock 3/8-16
40 1720931 1 BRACKET, Height of Cut
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
35
TP 400-3825-00-RG-UV
Page 36
40" Mower Deck - Height Adjustment & Roller Bar
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Apply Locktite
61
380 in hole prior
60
59
62
58
57
56
55
54
52
51
50
49
48
To "A"
43
42
19
to assembly.
29
28
2
16
21
53
47
63
46
17
85689AA
2
45
18
63
3
4
7
10
5
7
6
8
7
44
40
11
14
30
29
23
12
13
To Handle
Assy
24
32
33
34
26
23
31
3
19
20
22
45
44
41
7
40
39
3
2
16
31
38
15
25
27
23
2
1
1
9
From
"A"
38
Insert Must
Face Out
37
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
36
36
28
2
16
5
7
35
TP 400-3825-00-RG-UV
Page 37
40" Mower Deck - Height Adjustment & Roller Bar
PART NO. DESCRIPTIONREF NO QTY.
41 1720919 1 DECAL, Height of Cut
42 1719261 1 ROD, Adjustment
43 1922606 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4
44 1706645 1 TRUNNION, Rod
45 1915726 2 NUT, Hex, 5/8-11
46 118053 1 PIN
47 1960074 1 CLIP, Hair Pin, 1/8 x 1
48 1917421 1 NUT, Hex Jam 3/8-16
49 1960601 1 NUT, Hex Flange, 3/8-16
50 108241 1 GUIDE ASSEMBLY, Rod
51 1720704 1 ROD & WASHER ASSEMBLY, Adjust Handle
52 1651820 1 GRIP, Black Vinyl For Rod
53 1920397 1 NUT, Hex Lock Esna Light, 1/4-20
54 1720599 1 LATCH, 5/16 WIRE
55 1921159 1 CAPSCREW, Hex Head, 1/4-20 x 2-1/4
56 1721257 1 ROD, Latch
57 1720695 1 HANDLE ASSEMBLY, Lift
58 1676526 1 SPRING, Compression
59 1918265 2 WASHER, 5/16
60 1713995 1 GRIP, Black Soft for Rod
61 1723124 1 BUTTON, Black Nylon for Rod
62 1960674 1 PUSH NUT, 1/4
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
37
TP 400-3825-00-RG-UV
Page 38
40" Mower Deck - Housing, Arbors & Blades
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
25
34
35
33
32
31
30
29
36
27
37
41
40
39
38
85687AA
4
3
5
6
7
8
9
10
11
12
1
2
3
13
28
22
23
18
24
17
19
21
26
3
20
Torque to 45-55 ft.lbs. (61-75 Nm)
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
18
22
23
24
14
15
16
17
19
3
20
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
38
TP 400-3825-00-RG-UV
Page 39
40" Mower Deck - Housing, Arbors & Blades
PART NO. DESCRIPTIONREF NO QTY.
1 930584 1 CAPSCREW, Hex Head, 7/16-14 x 2-3/4 G8
2 1933263 1 WASHER, 7/16
3 1656916 4 WASHER, Spring
4 960644 1 CAPSCREW, Hex Head, 7/16-14 x 4-1/2 G8
5 1713091 1 PULLEY
6 1719870 1 HUB
7 1719766 2 SPROCKET & FLANGE ASSEMBLY, Riveted
8 1657969 2 SHIELD, Arbor Bearing, Upper
9 1655729 2 HOUSING, Arbor Top
10 1707335 2 GASKET, Foam Poly
11 1722396 2 ARBOR SHAFT & BEARINGS ASSEMBLY
12 1703273 2 HOUSING, Arbor Bottom with Lube Fitting
13 1924856 6 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 1/2
14 1721254 1 COVER, Arbor, LH
15 1686805 1 HOUSING ASSEMBLY, 40", Orange
15 41686805 1 HOUSING ASSEMBLY, 40", Red
15 61686805 1 HOUSING ASSEMBLY, 40", Black
16 1719624 1 BLADE, Mower, LH
17 1722258 2 PIN, Blade
18 1677274 2 ADAPTOR, Arbor
19 1722257 2 WASHER, Spline
20 927120 2 CAPSCREW, Hex Head, 7/16-14 x 2-1/4 G8
21 1664847 12 CAPSCREW, Taptite Hex Washer Head, 5/16-18 x 3/4
22 1700230 2 WASHER, Shim
23 1700229 2 SHIELD, Arbor Bearing, Lower
24 1655777 2 ADAPTER, Blade
25 1720600 1 DEFLECTOR, Discharge
26 1719623 1 BLADE, Mower, RH
27 1931335 1 CARRIAGE BOLT, 5/16-18 x 1
28 1931318 1 CARRIAGE BOLT, 1/4-20 x 7/8
29 1960518 1 NUT, Push
30 1960353 2 WASHER, 1/4
31 1704873 1 CLAMP
32 1916964 1 LOCKWASHER, Spring 1/4
33 1916622 1 NUT, Hex 1/4-20
34 1719597 1 DOOR, Mulching, Black Plastic
35 1705080 1 SPRING, Torsion
36 1719617 1 ROD, Pivot
37 1917372 1 NUT, Hex 5/16-18
38 1917356 1 LOCKWASHER, Spring 5/16
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
39
TP 400-3825-00-RG-UV
Page 40
40" Mower Deck - Housing, Arbors & Blades
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
25
34
35
33
32
31
30
29
36
27
37
41
40
39
38
85687AA
4
3
5
6
7
8
9
10
11
12
1
2
3
13
28
22
23
18
24
17
19
21
26
3
20
Torque to 45-55 ft.lbs. (61-75 Nm)
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
18
22
23
24
14
15
16
17
19
3
20
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
40
TP 400-3825-00-RG-UV
Page 41
40" Mower Deck - Housing, Arbors & Blades
PART NO. DESCRIPTIONREF NO QTY.
39 1919381 1 WASHER, 5/16
40 1933988 1 NUT, Push
41 1721255 1 COVER, Arbor, RH
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694377 - 40" Mower
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
41
TP 400-3825-00-RG-UV
Page 42
Page 43
Hardware Identification & Torque Specifications
Common Hardware Types
Hex Head Capscrew
Carriage Bolt
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
second number is present it represent the
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
second number represents the
example, and the final number is the
bolt or screw (in this example 2 inches long).
, meaning the
Nominal size
inside diameter
, or
body diameter
threads per inch
body length
Washer
Lockwasher
Hex Nut
is 1/2 inch; if a
threads per inch
is 1/2 inch; the
(16 in this
of the
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
Nut, 1/2”
Inside
Diameter
1
1/4 3/4
1/2
Screw, 1/2 x 2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Body
Diameter
Body
Length
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
Size Of
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32
8-36
10-24
10-32
1/4-20
1/4-28
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
No
Marks
SAE Grade 2 SAE Grade 5 SAE Grade 8
in/lbs in/lbs
19
2.1
20
2.3
27
3.1
31
3.5
66
7.6 8 10.9 12 16.3
76
8.6 10 13.6 14 19.0
30
31
43
49
NOTES
3.4
3.5
4.9
5.5
in/lbs
41
43
60
68
4.6
4.9
6.8
7.7
Wrench & Fastener Size Guide
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16
5/16” Bolt or Nut
Wrench—1/2”
3/8
3/8” Bolt or Nut
Wrench—9/16”
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”
Page 44
MANUFACTUR ING, INC.
500 N. Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
© Copyright Simplicity Manufacturing, Inc.
All Rights Reserved. Printed In USA.
Loading...