Simplicity 1694238 User Manual

Rev. 09/2002
TP 400-3542-00-AT-SMA
A
TTACHMENT
I
LLUSTRATED
P
ARTS L
© Copyright 2002 Simplicity Manufacturing, Inc.All Rights Reserved.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
A
TTACHMENT
Mfg. No. Description
1694238 Two Stage Snowthrower, 42”
2
TP 400-3542-00-AT-SMA
© Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
Auger Drive Group - 42”
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
986154
Marked side of worm gear must contact against left thrust washer to assure proper gear mesh.
Auger assembly stamped "R".
Auger assembly stamped "L".
Apply grease until it appears at ends of auger assembly (2 places).
Torque to 9 - 11 ft-lbs.
Seal Kit
14
15
16
19
13
17
18
32
23
40
39
35
38
37
36
34
33
31
30
27
26
1
15
29
32
35
2928
23
23
20
21
22
41
25
24
3
2
3
4
5
12
8
7
6
8
9
10
11
42
The above parts group applies to the following Mfg. Nos.:
1694238 Two-Stage Snowthrower, 42”
3
TP 400-3542-00-AT-SMA
Auger Drive Group - 42”
1 918312 1 KEY, Woodruff, 3/16 x 5/8 2 1919438 1 NUT, Hex Lock ESNA, 5/16-18 3 1920397 3 NUT, Hex Lock ESNA, 1/4-20 4 1723994 1 IMPELLER ASSEMBLY, 42" 5 1931335 1 CARRIAGE BOLT,5/16-18 x 1, Black 6 1723950 1 GEARBOX ASSEMBLY, 42" 7 1933260 4 CAPSCREW, Hex Whiz Lock, 3/8-16 x 3/4 8 922138 2 KEY, Hi Pro, 1/4 x 7/8
9 1960506 1 CAPSCREW, Hex Head, 1/4-20 x 1-7/8, Black 10 1724003 1 PULLEY 11 1928721 1 SETSCREW, Square Head, 5/16-18 x 1/2 12 1723997 1 BUSHING 13 1723995 1 SHAFT, Worm 14 1612093 1 SEAL, Oil 15 1612149 2 BUSHING, Flange 16 1612127 1 COLLAR, Thrust 17 1612142 1 GEAR, Rolled Worm 18 168111 1 WASHER, Thrust 19 936098 1 PIN, Drivelok, 3/16 x 1-1/2 20 1723922 1 SUPPORT, Gear Box 21 1931333 2 CARRIAGE BOLT, 5/16-18 x 3/4 22 1931277 2 NUT, Hex Flange Whiz Lock, 5/16-18 23 1923358 8 LOCKNUT, Hex, 1/4-20 24 1723931 2 SHAFT 25 1921962 2 CAPSCREW, Hex Head, 1/4-20 x 1-3/4 26 1723991 1 AUGER ASSEMBLY, LH, 42" 27 1723990 1 AUGER ASSEMBLY, RH, 42" 28 921133 2 FITTING, Lube, 1/4 29 1918447 2 PIN, Cotter, 3/32 x 3/4 30 1668344 2 PIN, Shear 31 1960346 6 CAPSCREW, Hex Head, 1/4-20 x 7/8 32 118118 2 SEAL 33 1668971 1 PLUG, Pipe, Tapered, 1/8 34 1612136 1 CASE, Gear, LH 35 118315 2 WASHER, Thrust 36 1612141 1 GEAR, Worm 37 930246 1 KEY, Woodruff, 1/4 x 3/4 38 1612117 1 SHAFT, Auger 39 1612124 1 GASKET 40 1612137 1 CASE, Gear, RH 41 1923282 2 CAPSCREW, Hex Head, 1/4-20 x 2-1/2 42 1686947 1 SEAL KIT, for Gear Box, Reference No. 6
REF NO. PART NO. QTY. DESCRIPTION
Footnotes:
The above parts group applies to the following Mfg. Nos.:
1694238 Two-Stage Snowthrower, 42”
4
TP 400-3542-00-AT-SMA
© Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
Auger Housing Group - 42”
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
986170
Coat top and bottom of chute ring with grease.
Scraper blade should be on inside of housing.
Plastic washer (Ref. 3) goes between chute
and deflector.
3
5
6
7
9
10
11
12
13
14
42
43
44
45
46
47
48
50
51
3
37
49
36
28
27
8
10
8
9
52
4
41
2
1
10
24
25
40
32
20
16
33
9
34
18
15
16
17
19
20
xx18
22
23
21
26
30
31
14
32
35
3
37
36
38
39
51
29
The above parts group applies to the following Mfg. Nos.:
1694238 Two-Stage Snowthrower, 42”
5
TP 400-3542-00-AT-SMA
Auger Housing Group - 42”
1 1704446 1 GUARD & SUPPORT ASSEMBLY
2 1960001 3 SCREW, Hex Washer Head, Plastite, #10-14 x 5/8
3 1931333 11 CARRIAGE BOLT, 5/16-18 x 3/4
4 960210 1 WASHER, Nylon
5 1919326 1 WASHER, 5/17, Black
6 1919438 1 NUT, Hex Lock ESNA, 5/16-18
7 1723948 1 CHUTE & DEFLECTOR ASSEMBLY
8 1702219 3 SPACER
9 1921319 6 WASHER, 1/4, Black 10 1960126 4 NUT, Push, Black 11 1611945 1 ROD 12 1611939 1 SPRING, Compression 13 1700048 1 BOOT, Water 14 1724568 1 CABLE & KNOB ASSEMBLY
(Includes Ref. Nos. 13, 22, 23, 24, 25, 27 & 28) 15 1916622 2 NUT, Hex, 1/4-20 16 1916964 3 LOCKWASHER, 1/4, Black 17 1960151 2 WASHER, 1/4, Black 18 1668344 1 PIN, Flat Head Drilled 19 1721590 1 BRACKET, Mounting 20 1924009 3 CAPSCREW, Hex Head, 1/4-20 x 7/8, Black 21 1960221 1 CLIP, Hair Pin 22 1960600 1 SCREW, Pan Head, #8-32 x 11/16 23 1719138 1 HANDLE, cable 24 1717477 1 GEAR, Chute 25 1666613 3 HOLD DOWN, Chute, Nylon 26 1705920 1 BRACKET, "L" 27 1715787 2 CUTTER, Drift 28 1921332 4 CAPSCREW, Hex Head, 5/16-18 x 3/4, Black 29 1724210 1 SWITCH, Rocker, Chute Rotator 30 1723117 1 HARNESS ASSEMBLY, Chute Rotator 31 1716987 1 HARNESS ASSEMBLY, Power Outlet 32 1722735 1 HARNESS ASSEMBLY, Spout Rotator 33 1923358 1 NUT, Hex Center Lock, 1/4-20, Black 34 1717480 1 PINION 35 1717591 1 ROD & BAR ASSEMBLY 36 1917356 7 LOCKWASHER, 5/16, Black 37 1917372 4 NUT, Hex, 5/16-18, Black 38 1723930 1 COVER, Pinion 39 1925003 2 CAPSCREW, Hex Washer Head, 1/4-20 x 1/2 40 1715885 1 MOTOR, Electric 41 172279 2 FLANGE, Bearing 42 173934 2 BEARING, Cartridge 43 172278 2 FLANGE, Bearing 44 1923325 6 CAPSCREW, Hex Head, 5/16-18 x 7/8, Black 45 1916950 4 NUT, Hex, 3/8-16, Black 46 1916965 4 LOCKWASHER, 3/8 47 1924940 4 WASHER, 3/8, Black 48 1723916 2 SKID PLATE ASSEMBLY
REF NO. PART NO. QTY. DESCRIPTION
Footnotes:
The above parts group applies to the following Mfg. Nos.:
1694238 Two-Stage Snowthrower, 42”
6
TP 400-3542-00-AT-SMA
© Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
Auger Housing Group - 42”
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
986170
Coat top and bottom of chute ring with grease.
Scraper blade should be on inside of housing.
Plastic washer (Ref. 3) goes between chute
and deflector.
3
5
6
7
9
10
11
12
13
14
42
43
44
45
46
47
48
50
51
3
37
49
36
28
27
8
10
8
9
52
4
41
2
1
10
24
25
40
32
20
16
33
9
34
18
15
16
17
19
20
xx18
22
23
21
26
30
31
14
32
35
3
37
36
38
39
51
29
The above parts group applies to the following Mfg. Nos.:
1694238 Two-Stage Snowthrower, 42”
7
TP 400-3542-00-AT-SMA
Auger Housing Group - 42”
49 1931350 4 CARRIAGE BOLT, 3/8-16 x 1, Black 50 1723986 1 BLADE, Scraper, 42" 51 1935048 15 NUT, Hex Flange Lock, 5/16, Black 52 1723974 1 HOUSING & IMPELLER ASSEMBLY, 42"
REF NO. PART NO. QTY. DESCRIPTION
Footnotes:
The above parts group applies to the following Mfg. Nos.:
1694238 Two-Stage Snowthrower, 42”
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of
in/lbs in/lbs
in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32
19
2.1
30
3.4
41
4.6
8-36
20
2.3
31
3.5
43
4.9
10-24
27
3.1
43
4.9
60
6.8
10-32
31
3.5
49
5.5
68
7.7
1/4-20
66
7.6 8 10.9 12 16.3
1/4-28
76
8.6 10 13.6 14 19.0 5/16-18 11 15.0 17 23.1 25 34.0 5/16-24 12 16.3 19 25.8 27 34.0 3/8-16 20 27.2 30 40.8 45 61.2 3/8-24 23 31.3 35 47.6 50 68.0 7/16-14 30 40.8 50 68.0 70 95.2 7/16-20 35 47.6 55 74.8 80 108.8 1/2-13 50 68.0 75 102.0 110 149.6 1/2-20 55 74.8 90 122.4 120 163.2 9/16-12 65 88.4 110 149.6 150 204.0 9/16-18 75 102.0 120 163.2 170 231.2 5/8-11 90 122.4 150 204.0 220 299.2 5/8-18 100 136 180 244.8 240 326.4 3/4-10 160 217.6 260 353.6 386 525.0 3/4-16 180 244.8 300 408.0 420 571.2 7/8-9 140 190.4 400 544.0 600 816.0 7/8-14 155 210.8 440 598.4 660 897.6 1-8 220 299.2 580 788.8 900 1,244.0 1-12 240 326.4 640 870.4 1,000 1,360.0
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
NOTES
1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque values must meet this specification.
Hardware Identification & Torque Specifications
Common Hardware Types
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside Diameter
Nut, 1/2”
No
Marks
3/8” Bolt or Nut
Wrench—9/16”
3/8
5/16” Bolt or Nut
Wrench—1/2”
5/16
1/4” Bolt or Nut
Wrench—7/16”
1/4
1/2” Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16 DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
, meaning the
inside diameter
is 1/2 inch; if a
second number is present it represent the
threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the
Nominal size
, or
body diameter
is 1/2 inch; the
second number represents the
threads per inch
(16 in this
example, and the final number is the
body length
of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Loading...