cals know, in certain quantities, to cause cancer,
birth defects, or other reproductive harm.
0
Copyright 1997 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
TP L00-2079-01-R‘-snl
exhaust
AWARNING
from this product contains chemi-
Identification Numbers
When contacting your Authorized
Dealer for replacement parts, service,
or information YOU MUST HAVE
THESE NUMBERS.
169XXXX
IDENTIFICATION NUMBERS
Record your model name/number, tractor and mower
deck manufacturer numbers and engine serial number in
the space provided for easy reference.
l
The Tractor I.D. tag is located on the left-side, of the
frame, as shown below.
l
The Mower Deck I.D. tag is also on the left side, on
top of the mower deck.
l
For location of Engine Serial Number, refer to the
Engine Owner’s Manual.
Be sure to fill out and return the Warranty Registration
Card supplied with your tractor.
Mowe;
Identification Tag
Deck
2
A
Safety Rules
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of
unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This
ina
deck is capable of amoutatina hands and feet and throwina
obiects.
The triangle a in text signi-
fies important cautions or warnings which must be followed.
mow-
GENERAL OPERATION
l Read, understand, and follow all instructions in the
manual and on the unit before starting.
l Only allow responsible adults, who are familiar with
the instructions, to operate the unit.
l Clear the area of objects such as rocks, toys, wire,
etc., which could be picked up and thrown by the
blade(s).
l Be sure the area is clear of other people before mow-
ing. Stop unit if anyone enters the area.
l Never carry passengers.
l Do not mow in reverse unless absolutely
Always look down and behind before and while
elling
in reverse.
l Be aware of the mower discharge direction and do
necessary.
trav-
not point it at anyone. Do not operate the mower
without either the entire grass catcher or the deflector
in place.
l Slow down before turning.
l Never leave a running unit unattended. Always
disengage the PTO, set parking brake, stop engine,
and remove keys before dismounting.
l Turn off the PTO switch to disengage the blades
when not mowing.
l Stop engine before removing grass catcher or
unclogging chute.
l Mow only in daylight or good artificial light.
l Do not operate the unit while under the influence of
alcohol or drugs.
l Watch for traffic when operating near or crossing
roadways.
l Use extra care when loading or unloading the unit
into a trailer or truck.
SLOPE OPERATION
1.
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe’ injury or
death. All slopes require extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not mow it.
Never operate on slopes greater than 30 percent
(16.7”) which is a rise of three feet vertically in 10 feet
horizontally. When operating on slopes that are
greater than 15 percent (6.5”) but less than 30 percent
use front counterweights and rear wheel weights (see
your dealer). Select slow ground speed before driving
onto slope. In addition to front and rear weights, use
extra caution when operating on slopes with
mounted grass catcher. Mow UP and DOWN the slope,
never across the face, use caution when changing
directions and DO NOT START OR STOP ON SLOPE.
Do
l See your authorized dealer for recommendations of
wheel weights or
l Mow up and down slopes, not across.
l Remove obstacles such as rocks, tree limbs, etc.
l Watch for holes, ruts, or bumps. Uneven terrain could
overturn the unit. Tall grass can hide obstacles.
l Use slow speed. Choose a low gear so that you will
not have to stop or shift while on the slope.
l Use extra care with grass catchers or other attach-
ments. These can change the stability of the unit.
l Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction.
Do Not
l Do not start or stop on a slope. If tires lose traction,
disengage the blade(s) and proceed slowly straight
down the slope.
l Do notturn on slopes unless necessary, and then,
turn slowly and gradually downhill, if possible.
l Do not mow near drop-offs, ditches, or embank-
ments. The mower could suddenly turn over if a
wheel is over the edge of a cliff or ditch, or if an edge
caves in.
l Do not mow on wet grass. Reduced traction could
cause sliding.
l Do not by to stabilize the unit by putting your foot on
the ground.
l Do not use grass catcher on steep slopes.
WARNING - SLOPE OPERATION
A
counteweights to improve stability.
rear-
Safety Rules
CHILDREN
Tragic accidents can occur if the operator is not alert to
SERVICE AND MAINTENANCE
l Use extra care in handling gasoline and other fuels.
the presence of children. Children are often attracted to
the unit and the mowing activity. Never assume that chil-
dren will remain where you last saw them.
l Keep children out of the mowing area and under the
watchful care of another responsible adult.
l Se
alert
and turn unit off if children enter the area.
l Before and during reverse operation, look behind and
down for small children.
l Never carry children. They may fall off and be seri-
l Never run a unit in an enclosed area.
l Keep nuts and bolts, especially blade attachment
ously injured or interfere with safe unit operation.
l Never allow children to operate the unit.
l Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
TRANSPORTING AND STORAGE
A
WARNING
When transporting this tractor on an open trailer,
make sure unit is facing forward, toward the
direction of travel. If tractor is facing backward,
wind lift could cause damage to the hood.
l Always observe safe refueling and fuel handling prac-
tices when refueling the tractor after transportation or
storage.
l Always follow the engine manual instructions for
storage preparations before storing the tractor for
both short and long term periods.
l Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
l Never store the unit or fuel container inside where
there is an open flame or pilot light, such as in a
water heater. Allow unit to cool before storing.
They are flammable and vapors are explosive.
a) Use only an approved container.
b) Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling. Do
not smoke.
c) Never refuel the unit indoors.
bolts, tight and keep equipment in good condition.
l Never tamper with safety devices. Check their proper
operation regularly.
l Keep unit free of grass, leaves, or other debris build-
up. Clean up oil or fuel spillage.
l Stop and inspect the equipment if you strike an
object. Repair, if necessary, before restarting.
l Never make adjustments or repairs with the engine
running unless specified otherwise in the engine
manufacturer’s manual.
l Grass catcher components are subject to wear, dam-
age, and deterioration, which could expose moving
parts or allow objects to be thrown. Frequently check
components and replace with manufacturer’s recom-
mended parts, when necessary.
l Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves, and use extra caution when
servicing them.
l Check brake operation frequently. Adjust and service
as required.
l Use only factory authorized replacement ‘parts when
making repairs.
9
Always comply with factory specifications on all
settings and adjustments.
l Only authorized service locations should be utilized
for major service and repair requirements.
*
Never attempt to make major repairs on this unit
unless you have been properly trained. Improper service procedures can result in hazardous
oberation,
equipment damage and voiding of manufacturer’s
warranty.
Never place hands near the hydro pump cooling
fan when the tractor is running. Cooling fan IS
4
Safety Decals
GENERAL
This unit has been designed and manufactured to provide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effectively, we have placed several safety labels on the unit to
remind you of this important information while you are
operating your tractor.
put
hands or feet
not
mower deck while
under
Decal - Danger
Part No. 1704276
All WARNING, CAUTION and instructional messages on
your tractor and mower should be carefully read and
obeyed. Personal bodily injury can result when these
instructions are not followed. The information is for your
safety and it is important! The safety decals below are on
your tractor and mower.
If any of these decals are lost or damaged, replace them
at once. See your local dealer for replacements.
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operatipn.
Brake PedalBrake Pedal
I. Forward Direction PedalI. Forward Direction Pedal
I. Rear Direction PedalI. Rear Direction Pedal
&itch
&itch
igure 1. Tractor & Mower Controls - Hydro Model
CONTROLS - GEAR MODEL
A,. Steering Wheel
B
. Throttle
C :.
Parking Brake Knob
I.
Ignition Key/Switch
0
,.
Headlight Switch
E
PTO
F
i.
Mower Height Adjustment
G
I. Clutch/Brake Pedal
H
I
Gear
._-
. .
(Ek_
_~?ctric
selector
Clutch) Switch
Lever
-
-
L
Figure 2. Tractor & Mower Controls - Gear Model
6
Operation
GENERAL
Before first time operation, drive in an open area without
mowing, to become accustomed to the unit. Be
read all information in the Safety and Operation sections
before attempting to operate this tractor and mower.
sure
to
SAFETY INTERLOCK SYSTEM
Your tractor is equipped with a seat switch safety system. Check the seat switch operation every fall and
spring with the following three tests.
Test 1
the following conditions exist:
WARNING
A
Never allow passengers to ride on the unit.
To reduce fire hazard, keep the engine and
mower free of grass, leaves and excess grease.
The interlock safety switches are for your safety.Test 2
Do
not
attempt to bypass them.
WARNING - SLOPE OPERATION
A
Never operate on slopes greater than 30 percent
(16.7”) which is a rise of three feet vertically in 10 feet
horizontally. When operating on slopes that are
greater
your dealer). Select slow ground speed before driving
onto slope. In addition to front and rear weights, use
extra caution when operating on slopes with
directions and DO NOT START OR STOP ON SLOPE.
than 15 percent (5.5”) but less than 30 percent
use
front counterweights
mounted grass catcher.
never across the face, use caution when changing
and rear wheel weights (see
rear-
Mow
UP and DOWN the slope,
l Transmission is out of neutral.
* PTO switch is engaged.
l Clutch/brake pedal is not fully depressed.
following conditions are met:
l Transmission is in neutral.
l PTO switch is disengaged.
l Clutch/brake pedal is fully depressed.
Test 3
following conditions exist:
l Operator rises off seat with transmission in gear and
the clutch/brake pedal not fully depressed, and/or the
parking brake is not set.
l Operator rises off seat with clutch/brake pedal not
depressed;
l Operator rises off seat with PTO engaged,
NOTE: Once the engine has stopped, the PTO Switch
(Fz
Figures 1 & 2) must be turned off after operator
returns to the seat in order to start the engine.
-
Engine should NOT crank if any of
-
Engine should crank if ALL of the
-
Engine should shut off if any of the
Towing the tractor will cause transmission
damage. Do not use another vehicle to push
WARNING
If the tractor does not pass the test, do not operate tractor. See your authorized dealer. Under no
circumstance should you attempt to defeat the
purpose of the safety system.
A
Operation
CHECKS BEFORE STARTING
I.
Make sure you have proper wheel or counterweights
installed if required. See Slope Operation in the
Safety Rules section. Make sure any slopes are with-
in required limits.
2.
Check that crankcase is filled to full mark on dipstick.
See the engine Operator’s Manual for instructions
and oil recommendations.
3.
Make sure all nuts, bolts, screws and pins are in
place and tight.
Make sure you can reach all controls from operator’s
4.
positions. If not, see SEAT ADJUSTMENT.
5.
Fill the gasoline tank with fresh gasoline. Fill to bot-
tom of filler neck to avoid spillage and overflow. DO
NOT mix oil with gasoline. Refer to engine manual for
gasoline recommendations.
WARNING
A
Gasoline is highly flammable and must be handled with care. Never fill the tank when the
engine is still hot from recent operation. Do not
allow open flame, smoking or matches in the
area. Avoid overfilling and wipe up any spills.
Figure 3. Clutch/Brake Pedal Operation
A. Clutch/Brake Pedal - Gear Model
Brake Pedal - Hydro Model
B. Parking Brake Knob
6. Move the throttle (B, Figures 1
up the engine by running it for at least a minute
before engaging the PTO switch or driving the tractor
&
2) to SLOW. Warm
CLUTCH/BRAKE PEDAL OPERATION
On gear model, depressing the pedal (H, Figure 2)
halfway disengages the transmission drive. Depressing
pedal further applies the tractor brake.
On hydro model, depressing the pedal applies the tractor brake.
/.-
PARKING BRAKE
Parking brake can be applied by fully depressing the
brake pedal (H, Figures 1 &
parking brake knob (C, Figures 1 & 2).
2),
then pulling up on the
STARTING THE ENGINE
1.
While sitting in the operator seat, set the parking
brake.
2.
Set the throttle (B, Figures 1 & 2) all the way up to
CHOKE. A warm engine may not require choking.
3.
Disengage the PTO by pushing the switch all the way
down (F, Figures 1
4.
On hydro models, with your foot off the pedals
J, Figure 1) the tractor is in the neutral position.
On gear models, put the gear selector
neutral.
5.
Insert the key into the ignition switch (D, Figure 1 & 2)
and turn it to START.
&
2)
(I &
(I,
Figure 2) in
DRIVING THE TRACTOR
Make sure dewed
On hydro model, ground speed is infinitely variable
according to how far the pedals (I & J, Figure 1) are
moved in the forward or reverse position.
On gear model, ground speed is selected by fully
depressing the clutch/brake pedal, then moving the gear
selector
mowing is done in 3rd gear with engine speed at full
throttle. If the terrain is rough, hilly, or sloping, use first
or second gear. If the grass is wet or over three inches
(76mm) high, use full engine speed with low gear so the
mower will have enough power to cut the grass. Shift
gears only with tractor stopped and clutch/brake pedal
fully depressed.
1. If you are ready to mow, set the mower to the desired
2. Set the throttle (B, Figures 1
3. Engage the mower PTO by pulling up on the switch
(I,
Figure 2) to the appropriate position. Most
cutting height (see Adjusting Mower Cutting Height)
and adjust the seat so that the controls can be easily
reached (see Seat Adjustment).
Full speed is recommended for mowing.
(F, Figures 1
&
2).
dwectron
of travel IS clear of
&
2) for desired speed.
6
Operation
4. On hydro model, release the parking brake by
depressing the brake pedal (H, Figure
down on either pedal (I or J, Figure 1) for the desired
direction and speed of travel.
On gear model, fully depress clutch/brake pedal (H,
Figure 2) to release the parking brake and disengage
the clutch. Use the gear selector (I, Figure 2) to
select the gear best suited for conditions, then slowly
release clutch/brake pedal to engage clutch and start
tractor in motion.
l),
then press
STOPPING THE TRACTOR
1. On hydro model,
als (I & J, Figure 1) to make a smooth stop. To make
a more rapid stop, depress the brake pedal (H, Figure
1).
On gear model, press the clutch/brake pedal (H,
Figure 2) down only far enough to disengage the
clutch to make a gradual stop. For a more rapid stop,
press pedal down fully to apply the brake.
2. Engage the parking brake by pulling up on the knob
(C, Figure 1 & 2) with the brake pedal fully
depressed.
3. Disengage the PTO by pushing down on the switch
(F, Figures 1
4. Set engine throttle control to mid-throttle position and
turn the ignition key to off. Remove the key.
NOTE: Stopping the engine at any speed other than mid-
throttle can cause engine damage.
engine with the throttle control in the IDLE position.
gradually take your foot off the ped-
&
2).
Do not stop the
PUSHING THE TRACTOR BY HAND
Towing the tractor will cause transmission
damage. Do not use another vehicle to push
Hydro Models
1. With engine off and key removed, disengage the
PTO by pushing the switch (F, Figures 1
way down.
2. See Figure 4. The release lever is located on the rear
of the tractor. To release the transmission pull the
lever up, back and then down to lock. DO NOT
ACTIVATE WHILE ENGINE IS RUNNING.
Note: To drive the tractor the release lever most be
moved completely forward and pushed down into locked
position to engage the transmission.
&
2) all the
Before leaving the operator’s position for any
reason, engage the parking brake, disengage the
PTO, stop the engine and remove the key.
To reduce fire hazard keep the engine tractor
v”“”
and mower free of grass, leaves and excess
grease. Do not stop or park tractor over dry
leaves, grass or combustible
mate$als.
Figure 4. Release Lever - Hydro Models
1. With engine off and key removed, disengage the
PTO by pushing the switch (F, Figures 1 & 2) all the
2. Place the gear selector in the NEUTRAL position.
3.
~~~~~~rking
brake.
Operation
MOWER INSTALLATION & REMOVAL
WARNING
A
Engage parking brake, disengage PTO, stop
engine and remove key before attempting to
install or remove the mower.
NOTE: Perform mower removal and installation on a
hard, /eve/ surface such as a concrete floor.
1.
Turn the front wheels of the tractor full left.
2. Place the mower in lowest cutting position.
3. Move lever (C, Figure 6) to release belt tension, then
slide belt off of PTO pulley.
4. Remove clip (A, Figure 5) from right side of rod. Pull
rod (A, Figure 6) out from left side.
5. Disconnect the front hitch by pulling out on the
release rod (A, Figure 7) and lifting the mower hitch
off the tractor hitch. Slide the mower deck out from
under the right side of the tractor.
6. Install the mower in reverse order of removal.
NOTE: When installing rod (A, Figure
wheels slightly
/et?
or right helps to align the holes.
S),
turning the
front
Figure 5. Mower Deck - Right Side
A. ClipC. Height Adjustment
B. Pin & Clip
Lever
ADJUSTING MOWER
CUlTlNG
HEIGHT
&
GAUGE WHEELS
NOTE: Perform adjustment on a hard, level surface such
as a concrete floor.
1. Set the mower height adjustment lever (A, Figure 8)
to the desired cutting height.
2. Remove the pin &clip (B, Figure 8) from each mower
deck front gauge wheel.
3. Adjust the gauge wheels to achieve the appropriate
mower deck-to-ground clearance, as shown in Figure
8. Reinstall pin 8 clip to each wheel.
Figure 6. Mower Deck - Left Side (38” Deck Shown)
A. Rod
B. Pin & Clip
C. Lever
Figure 7. Front Hitch
A. Release Rod
B. Hitch
2” with Height Adjuster Lever in upper 3 slots
Figure 8. Adjusting Mower Deck Gauge Wheels
A. Mower Height Adjustment Lever
B. Pin
&
Clip
10
Loading...
+ 23 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.