Simplicity 1690562 User Manual
Specifications and Main Features
- Engine Manufacturer: Briggs & Stratton, 4 Cycle & Air Cooled
- Engine Model Push: 92908
- Engine Model Self Propelled: 92998
- Cylinder Type: Flat 1
- Bore and Stroke: 2 9/16 inch and 1 3/4 inch
- Capacity: 9.02 cu in or 147.8 cc
- Class of Governor: Air Vane
- Container Volume: 1 ¼ pints
- Starter Type: Tri-Magnet
- Water Separator Type: Oil foam
- Water Container Amount: 1 quart
- Choke Type: Automatic choke with purge position.
- Starter Method: Manual geared rewind vertical pull.
- CHAMPION AUTOLITE BOSCH SPARK PLUG:
- CJ OBSERVING: 8 235 WS9SE.
- J-8 295.
- CJ-8 245 RESISTORSHORTPLUG:
- RJ-8 306 RESISTORLONGPLUG:
- SPARLMAN WITH: 0.0: 30' 0.76 MM Gap:
- J D W 0 N: 20”: 051 MM Ignition Point Gap:
- Intake Valve: 0.005” to 0.007 inches or 0.13 MM to 0.18 MM
- Exhaust Valve: 0: 0 to 0.012: Inches: 0; 23mm to 0:28mm
- Housing: Mower Housings are made out of die cast aluminum
- Position of Discharge: Right front corner
- Grass Catcher: This is attached to the top right side of the deck
- Front: 152: 4 6’ high density plastic
- Rear Wheels (Push): 10° (254 mm)- Utilizing a robust high density plastic material
- Rear Wheels (Propelling): 10° (254mm)- Constructed using steel plus bearings.
- Width of Working Angle: Between 25.4-76.2 mm while including 6 settings
- Heights of Handle: Comes with 2 adjustable designs lying parallel to the engine block.
- Additions in Lawn Mowers: Rear foliage containers, mulching, or side panel discharge
-Powered Machines Nan Optional Assisting Motors Machines: With Reinforcing Infrastructure High-Speed Rear Wheels-Chained Drives - Cut Through Ethnicity At 3400 Revolutions Per Minute Engine, Reach Rates of Up To 2.72 Mph (4.4 km/h)
- Cut Containing Terms High: 3.6 Km/h 2.2 Mph
- Length Overall In High Handle Position: 57-1/2’ (1460 mm)
- Measurement of Overall Width: 25” (635 mm
- Measured Height When The Handle Is In A High Position Has The Following Ranges 39-1/2”: 1003 mm at the Cutting height of 3:76.2 mm
- Height (low handle position): 35-1/4” (895 mm) at 3” (76.2 mm) cutting height
Frequently Asked Questions
Q: What type of engine does the mower use?
The mower is equipped with a chance exuberance of a forty cycle Briggs & Stratton air-cooled.
Q: What is the displacement of the engine?
An engine’s potential is defined to be estimated remodeled excited at a time of 9.02 cu. in. (147.8 cc).
Q: In what manner can I activate the mower engine?
A: The Engine can be activated by advancing the throttle control indicator to the “Start” position. Pull the rewind starter grip with one foot firmly planted on the mower deck while it is on a leveled surface.
Q: The gasoline used is of what grade?
A: It is better to avoid mixing oil with gasoline, the engine while operating will use lead-free gasoline, either lower grade or lead-free which is clean and well-maintained.
Q: Give an estimate over how long can I use the engine oil?
A: Use of engine oil should be changed approximately after the first five hours of operation and later at a difference of 25 hours.
Q: What is the range of cutting height and how many are there?
A: The cutting height can be set at a range of 1 to 3 inches and has six different variations.
Q: What spark plug is used in electrical ignition?
A: The use of Champion Autolite Bosch plugs with a gap of 0.030” (0.76 mm) is recommended within the mower to make it more efficient.
Q: Is there any restriction with riding the mower at a slope?
A: Riding the mower at an inclination or slope isn’t prohibited though avoiding riding it at steep angles is preferred.
Q: How frequently should an Air Cleaner be used?
A: The cleaning process for Air Cleaners should be carried out every three months which is equivalent to a use period of 25 hours, Should one condition be met, the other becomes irrelevant.
User Manual
Loading...