Simplicity 1334,1694494,1694287,2690121 Operator's Manual
Print Vendor
Instructions
How to use this file
Operator’s Manuals
Paper Size: • 11x17
• Body - 50 lbs brilliant white offset or equivalent
• Cover - on pre-printed two tone “Swash” stock.
Press: • Body - 1 color, 2-sided
• Cover - 1 color, 1 sided
Bindery: • Saddle stitch, face trim *if too thick for saddle stitch, tape bind
Covers: • FRONT COVER is present at the beginning of the file.
• BACK COVER is the page immediately after the front cover.
• The part number for this manual (typically a 172_____ number) is
located on the front cover.
• This file may contain several manual which differ only by their covers.
See the part number at the bottom of the cover page. .
Body: • The body for all manuals is identical regardless of the cover.
• Odd number pages are always right hand pages, even number pages
are always left hand pages.
General: • This instruction sheet is NOT part of the manual and must not be
printed.
• Pages labeled “THIS PAGE INTENSIONALLY BLANK” are placement
pages and should NOT be printed.
THIS PAGE INTENTIONALLY BLANK
(FOR PLACEMENT ONLY - DO NOT PRINT)
OPERATOR’S
MANUAL
13HP Transaxle Drive Walk-Behind Mower
Mfg. No. Description
1334 Pacer, 13HP Walk-Behind Mower with 34” Deck
1694494 Pacer, 13HP Walk-Behind Mower (serial no. 000859 & below)
15HP Transaxle Drive Walk-Behind Mower
Mfg. No. Description
1694494 Pacer, 15HP Walk-Behind Mower (serial no. 000860 & above)
2690121 Pacer, 15HP Walk-Behind Mower with 34” Deck
34” Mower Deck
Mfg. No. Description
1694287 34” Mower Deck
Pacer Series
1725792
Rev. No. 06
Rev. Date: 7/2007
Supercedes 23077
TP 100-7102-06-PA-SD
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
www.simplicitymfg.com
Briggs & Stratton Yard Power Products Group
Copyright © 2007 Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
The Simplicity logo is a trademark of Briggs & Stratton
Corporation, Milwaukee, WI, USA.
1
Table of Contents
Safety Rules & Information.................................2
Safety Decals .......................................................5
Identification Numbers........................................5
Features & Controls ............................................6
Control Functions....................................................6
Safety Interlock System ..........................................7
Operating the Walk-Behind Mower....................8
General Operating Safety .......................................8
Checks Before Starting ...........................................8
Starting the Engine .................................................8
Driving the Mower ...................................................8
Operating On A Slope.............................................9
Stopping the Mower ................................................9
Adjusting Mower Cutting Height..............................9
Mowing..................................................................10
Mulch Plate Removal & Replacement ..................10
Pushing the Rider by Hand ...................................10
Storage .................................................................11
Starting After Long Term Storage .........................11
Regular Maintenance ........................................12
Maintenance Schedule .........................................12
Checking Tire Pressure ........................................12
Checking/Adding Fuel...........................................13
Fuel Filter ..............................................................13
Oil & Filter Change................................................13
Check / Change Air Filter......................................13
Lubrication ............................................................14
Battery Maintenance .............................................14
Checking the Battery Fluid...............................14
Cleaning the Battery and Cables .....................14
Servicing the Mower Blades .................................15
Troubleshooting, Adjustments & Service .......16
Troubleshooting the Mower ..................................16
Troubleshooting the Mower Deck .........................17
Deck Leveling Adjustment ....................................18
Belt Removal and Replacement ...........................19
Ground Speed Control Lever Adjustment .............20
PTO Clutch Adjustment ........................................21
Battery Charging ...................................................22
Parts & Accessories..........................................22
Lawn Care & Mowing Information .............LC—1
International Symbols ................................LC—8
NOTE: In this manual, “left” and “right” are referred to as
seen from the operating position.
WARNING
Engine exhaust from this product contains
chemicals known, in certain quantities, to cause
cancer, birth defects, or other reproductive harm.
WARNING
You must read, understand and comply with all safety
and operating instructions in this manual before
attempting to set-up and operate your machine.
Failure to comply with all safety and operating
instructions can result in loss of machine control,
serious personal injury to you and / or bystanders,
and risk of equipment and property damage. The
triangle in the text signifies important cautions or
warnings which must be followed.
2
TP 600-7158-00-UV-SN
GENERAL OPERATION
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before starting.
2. Do not put hands or feet near or under the machine.
Keep clear of the discharge opening at all times.
3. Only allow responsible adults, who are familiar with
the instructions, to operate this machine.
4. Clear the area of objects such as rocks,wire, toys,
etc., which could be thrown by the blade. Stay behind
the handle when the engine (motor) is running.
5. Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
6. Do not operate machine barefooted or while wearing
sandals. Always wear substantial footwear.
7. Do not pull machine backward unless absolutely necessary. Always look down and behind before and
while moving backward.
8. Never direct discharged material toward anyone.
Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator.
Stop the blade when crossing gravel surfaces.
9. Do not operate machine without the entire grass
catcher, discharge guard, rear guard, or other safety
protective devices in place and working.
10. Never leave a running machine unattended.
11. Stop the engine (motor) and wait until the blade
comes to a complete stop before cleaning the
machine, removing grass catcher, or unclogging the
discharge guard.
12. Operate machine only in daylight or good artificial
light.
13. Do not operate machine while under the influence of
alcohol or drugs.
14. Never operate mower in wet grass. Always be sure
of your footing; walk; never run.
15. Disengage the drive system, if so equipped, before
starting the engine (motor).
16. If the machine should start to vibrate abnormally, stop
the engine (motor) and check for the cause immediately. Vibration is generally a warning of trouble.
17. Always wear eye protection when operating machine.
18. See manufacturer’s instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
19 Watch for traffic when operating near or crossing
roadways.
20. Use extra care when loading or unloading the unit
into a trailer or truck.
21. Always wear eye protection when operating this unit.
22. Data indicates that operators, age 60 years and
above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the equipment safely
enough to protect themselves and others from injury.
23. Keep in mind the operator is responsible for accidents
occurring to other people or property.
24. All drivers should seek and obtain professional and
practical instruction.
25. Before using, always visually check that the blades
and blade hardware are present, intact, and secure.
Replace worn or damaged parts.
26. Disengage attachments before: refueling, removing
an attachment, making adjustments (unless the
adjustment can be made from the operator’s position).
27. Before leaving the operator’s position for any reason,
engage the parking brake (if equipped), disengage
the blades (PTO), stop the engine, and remove the
key.
28. To reduce fire hazard, keep the unit free of grass,
leaves, & excess oil. Do not stop or park over dry
leaves, grass, or combustible materials.
29. It is a violation of California Public Resource Code
Section 4442 to use or operate the engine on or near
any forest-covered, brush-covered, or grass-covered
land unless the exhaust system is equipped with a
spark arrester meeting any applicable local or state
laws. Other states or federal areas may have similar
laws.
TRANSPORTING AND STORAGE
1. When transporting the unit on an open trailer, make
sure it is facing forward, in the direction of travel. If
the unit is facing backwards, wind lift could damage
the unit.
2. Always observe safe refueling and fuel handling practices when refueling the unit after transportation or
storage.
3. Never store the unit (with fuel) in an enclosed poorly
ventilated structure. Fuel vapors can travel to an
ignition source (such as a furnace, water heater, etc.)
and cause an explosion. Fuel vapor is also toxic to
humans and animals.
4. Always follow the engine manual instructions for
storage preparations before storing the unit for both
short and long term periods.
5. Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
6. Never store the unit or fuel container inside where
there is an open flame or pilot light, such as in a
water heater. Allow unit to cool before storing.
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
This mowing deck is capable of amputating hands and feet and throwing objects.
The triangle in text signifies important cautions or warnings which must be followed.
Safety Rules & Information
3
Safety Rules and Information
CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
unit and the mowing activity. Never assume that children
will remain where you last saw them.
1. Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.
2. Be alert and turn mower off if a child enters the area.
3. Never allow children to operate the machine.
4. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may block your
view of a child.
EMISSIONS
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
2. Look for the relevant Emissions Durability Period and
Air Index information on the engine emissions label.
SLOPE OPERATION
Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death.
Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not
operate on it.
Control of a walk-behind or ride-on machine sliding on a
slope will not be regained by the application of the brake.
The main reasons for loss of control are: insufficient tire
grip on the ground, speed too fast, inadequate braking, the
type of machine is unsuitable for its task, lack of awareness
of the ground conditions, incorrect hitching and load distribution.
1. Mow across the face of slopes; never up and down.
Exercise extreme caution when changing direction on
slopes.
2. Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could cause a slip and fall
accident. Tall grass can hide obstacles.
3. Choose a slow speed so that you will not have to
stop or change speeds while on the slope.
4. Do not mow on wet grass or excessively steep
slopes. Poor footing could cause a slip and fall accident.
5. Never mow down slopes.
6. Avoid starting, stopping, or turning on a slope. If tires
lose traction (i.e. machine stops forward motion on a
slope), disengage the blade(s) (PTO) and drive slow
off the slope.
7. Keep all movement on slopes slow and gradual. Do
not make sudden changes in speed or direction,
which could cause a slip and fall accident.
8. Use extra care while operating machines with grass
catchers or other attachments; they can affect the
stability of the unit. Do not use on steeps slopes.
9. Do not mow near drop-offs, ditches, or embankments. You could lose your footing or balance.
10. Do not use grass catchers on steep slopes.
11. Do not mow slopes you cannot back up them.
12. Remove obstacles such as rocks, tree limbs, etc.
13. Use slow speed. Tires may lose traction on slopes
even through the brakes are functioning properly.
WARNING
Never operate on slopes greater than 17.6 percent
(10°) which is a rise of 3-1/2 feet (106 cm) vertically in
20 feet (607 cm) horizontally.
Select slow ground speed before driving onto slope.
Use extra caution when operating on slopes with
rear-mounted grass catchers.
Mow across the face of slopes, not up and down,use
caution when changing directions and DO NOT
START OR STOP ON SLOPE.
Safety Rules and Information
SERVICE AND MAINTENANCE
To avoid personal injury or property damage, use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Safe Handling of Gasoline
1. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
2. Use only approved gasoline containers.
3. Never remove the gas cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. Never fuel the machine indoors.
5. Never store the machine or fuel container where
there is an open flame, spark, or pilot light such as
near a water heater or other appliance.
6. Never fill containers inside a vehicle or on a truck bed
with a plastic bed liner. Always place containers on
the ground away from your vehicle before filling.
7. Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a
portable container, rather than from a gasoline dispenser nozzle.
8. Keep nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
9. If fuel is spilled on clothing, change clothing immediately.
10. Never over-fill the fuel tank. Replace gas cap and
tighten securely.
11. Use extra care in handling gasoline and other fuels.
They are flammable and vapors are explosive.
12. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
13. Replace all fuel tank caps and fuel container caps
securely.
Service & Maintenance
1. Never run the unit in an enclosed area where carbon
monoxide fumes may collect.
2. Keep nuts and bolts, especially blade attachment
bolts, tight and keep equipment in good condition.
3. Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if
they are not functioning properly.
4. Keep unit free of grass, leaves, or other debris buildup. Clean up oil or fuel spillage. and remove any fuelsoaked debris. Allow machine to cool before storage.
5. If you strike an object, stop and inspect the machine.
Repair, if necessary, before restarting.
6. Never make adjustments or repairs with the engine
running. Disconnect the spark plug wire(s) and
ground against the engine to prevent unintended
starting.
7. Check grass catcher components and the discharge
guard frequently and replace with manufacturer’s recommended parts, when necessary.
8. Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
9. Check brake operation frequently. Adjust and service
as required.
10. Maintain or replace safety and instructions labels, as
necessary.
11. Do not remove the fuel filter when the engine is hot
as spilled gasoline may ignite. Do not spread fuel
line clamps further than necessary. Ensure clamps
grip hoses firmly over the filter after installation.
12. Do not use gasoline containing METHANOL, gasohol
containing more than 10% ETHANOL, gasoline additives, or white gas because engine/fuel system damage could result.
13. If the fuel tank must be drained, it should be drained
outdoors.
14. Replace faulty silencers/mufflers.
15. Maintain or replace safety and instruction labels as
necessary.
16. Use only factory authorized replacement parts when
making repairs.
17. Always comply with factory specifications on all settings and adjustments.
18. Only authorized service locations should be utilized
for major service and repair requirements.
19. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper service procedures can result in hazardous operation,
equipment damage and voiding of manufacturer’s
warranty.
20. On multiple blade mowers, take care as rotating one
blade can cause other blades to rotate.
21. Do not change engine governor settings or overspeed the engine. Operating the engine at excessive
speed can increase the hazard of personal injury.
22. Disengage drive attachments, stop the engine,
remove the key, and disconnect the spark plug
wire(s) before: clearing attachment blockages and
chutes, performing service work, striking an object, or
if the unit vibrates abnormally. After striking an
object, inspect the machine for damage and make
repairs before restarting and operating the equipment.
23. Never place hands near the moving parts, such as a
hydro pump cooling fan, when the tractor is running.
(Hydro pump cooling fans are typically located on top
of the transaxle).
24. Units with hydraulic pumps, hoses, or motors:
WARNING: Hydraulic fluid escaping under pressure
may have sufficient force to penetrate skin and cause
serious injury. If foreign fluid is injected into the skin
it must be surgically removed within a few hours by a
doctor familiar with this form of injury or gangrene
may result. Keep body and hands away from pin
holes or nozzles that eject hydraulic fluid under high
pressure. Use paper or cardboard, and not hands, to
search for leaks. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines
are in good condition before applying pressure to the
system. If leaks occur, have the unit serviced immediately by your authorized dealer.
25. WARNING: Stored energy device. Improper release
of springs can result in serious personal injury.
Springs should be removed by an authorized technician.
26. Models equipped with an engine radiator: WARNING:
Stored energy device. To prevent serious bodily
injury from hot coolant or steam blow-out, never
attempt to remove the radiator cap while the engine
is running. Stop the engine and wait until it is cool.
Even then, use extreme care when removing the cap.
4
5
Safety Decals / Identification Numbers
SAFETY DECALS
This unit has been designed and manufactured to provide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effectively, we have placed several safety labels on the unit to
remind you of this important information while you are
operating your unit.
All DANGER, WARNING, CAUTION and instructional
messages on your rider and mower should be carefully
read and obeyed. Personal bodily injury can result when
these instructions are not followed. The information is for
your safety and it is important!
If any of these decals are lost or damaged, replace them
at once. See your local dealer for replacements.
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.
Decal - Danger
Part No. 1704276
Decal - Danger
Part No. 1704277
Decal - Dash Panel
Part No. 5047627
Decal - Warning
Part No. 5021818
Decal - Warning
Part No. 5049658
Decal - Hot
Part No. 1704473
ID Tag
When contacting your authorized dealer for replacement parts, service, or information you MUST have
these numbers.
Record your model name/number, manufacturer’s identification numbers, and engine serial numbers in the
space provided for easy access. These numbers can be
found in the locations shown.
NOTE: For location of engine identification numbers,
refer to the engine owner’s manual.
CE Models: Place the extra copy of the identification tag
in the manual
SSAAMMPPLLEE
SSAAMMPPLLEE
ENGINE REFERENCE DATA
Model Description Name/Number
Unit MFG
Number
PRODUCT REFERENCE DATA
Unit SERIAL
Number
Dealer Name
Date Purchased
Engine Make
Engine Type/Spec
Engine Model
Engine Code/Serial Number
Mower Deck MFG Number
Mower Deck SERIAL
Number
IDENTIFICATION NUMBERS
6
Features &
Controls
A. Ground Speed Control Levers
These levers control the ground speed of the mower.
The left and right levers are tied together so you can
operate either lever to control the mower’s ground
speed.
Moving a lever forward increases the FORWARD speed
of the mower, and pulling back on a levers increases the
REVERSE speed.
Note: The further a lever is moved away from the neutral
position the faster the mower will travel.
Please take a moment and familiarize yourself with the name, location, and function of
these controls so that you will better understand the safety and operating instructions
provided in this manual.
E
A
A
F
Figure 1. Control Locations
A. Ground Speed Control Levers
B. Engine Ignition Switch
C. Throttle/Choke Control
D. PTO Engagement Switch
E. Operator Presence / Parking Brake Handles
F. Fuel Tank Cap
B. Ignition Switch
The ignition switch starts and stops the engine, it has
three positions:
OFF Stops the engine and shuts off the
electrical system.
RUN Allows the engine to run and powers the
electrical system.
START Cranks the engine for starting.
NOTE: Never leave the ignition switch in the RUN position with the engine stopped–this drains the battery.
CONTROL FUNCTIONS
The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing
require the combined use of several controls applied in specific sequences. To learn what combination and sequence
of controls to use for various tasks see the OPERATION section.
E
D
B
C
7
Features & Controls
SAFETY
INTERLOCK SYSTEM
CHECK
This unit is equipped with safety interlock switches and
other safety devices. These safety systems are present
for your safety, do not attempt to bypass safety switches, and never tamper with safety devices. Check their
operation regularly.
Operational SAFETY Checks
Your unit is equipped with an operator presence switch
safety system. Check the operator presence switch
operation every fall and spring with the following tests.
Test 1 — Engine WILL NOT start if:
• PTO switch is engaged.
Test 2 — Engine WILL start if:
• PTO switch is NOT engaged.
Test 3 — Engine should SHUT OFF if:
• Operator releases the operator presence / parking
brake handles with PTO engaged.
Test 4 — Blade Brake Check
Mower blades and mower drive belt should come to a
complete stop within five seconds after electric PTO
switch is turned off (or operator releases operator presence handles). If mower drive belt does not stop within
five seconds, see your dealer.
NOTE: Once the engine has stopped, PTO switch must
be turned off in order to start the engine.
WARNING
If the unit does not pass a safety test, do not
operate it. See your authorized dealer. Under no
circumstance should you attempt to defeat the
purpose of the safety interlock system.
C. Throttle / Choke Control
Moving the throttle control fully forward is the CHOKE
position, which fully chokes the engine for cold starts. (A
warm engine may not require choking.) Moving the throttle control slightly back from the CHOKE position is the
FULL throttle position. Always operate the unit at FULL
throttle when mowing.
D. PTO Engagement Switch
The PTO Engagement Switch engages and disengages
the mower blades.
To engage the mower blades, pull up on the switch. To
disengage the mower blades, push down on the switch.
When the PTO engagement lever or switch is in the
Engaged position, the Engine Kill system is activated.
E. Operator Presence / Parking Brake
Handles
This control deactivates the engine kill system and disengages the parking brake when depressed. Release the
handles to activate the engine kill system and engage
the parking brake. The engine will shut off if the operator
releases the handles with the PTO engaged.
F. Fuel Tank Cap
To remove cap, turn counterclockwise.
Loading...