Parts Manual
Large Frame
Walk-Behind Snowthrowers
9.5HP Snowthrowers
Mfg. No. Description
1694589 9560E, 9.5HP Snowthrower
1694597 9560M, 9.5HP Snowthrower (CE)
10HP Snowthrowers
Mfg. No. Description
1694590 1060E, 10HP Snowthrower
1694598 1060M, 10HP Snowthrower (CE)
11HP Snowthrowers
Mfg. No. Description
1694591 1170E, 11HP Snowthrower
1694599 1170M, 11HP Snowthrower (CE)
12HP Snowthrowers
Mfg. No. Description
1694592 1280E, 12HP Snowthrower
1694600 1280M, 12HP Snowthrower (CE)
13HP Snowthrowers
Mfg. No. Description
1694593 1390E, 13HP Snowthrower
1694601 1390M, 13HP Snowthrower (CE)
Rev.
1731160
11/2005
Part No.:
TP 400-4155-01-LW-S
Table Of Content
s
PRODUCT COMPONENTS PAGES
Handles and Controls Group - 1060, 1170, 1280 & 1390 Models ......................................................................
Handles and Controls Group - 9560 Models .......................................................................................................
Engine and Frame Group with Power Boost .......................................................................................................
Engine and Frame Group without Power Boost ..................................................................................................
Auger and Impeller Group ....................................................................................................................................
Auger Housing and Chute Group - 38" Models ...................................................................................................
Auger Housing and Chute Group - 9560, 1060, 1170 & 1280 Models ...............................................................
Traction Drive Group ............................................................................................................................................
Wheels & Tires Group ..........................................................................................................................................
Decal Group .........................................................................................................................................................
Headlight Group ...................................................................................................................................................
12
16
20
22
26
30
34
36
38
Torque Specification Chart ..................................................................... Inside Back Cover
4
8
Handles and Controls Group - 1060, 1170, 1280 & 1390 Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Linkage adjustment for traction and
auger drive with power boost: with
drive levers engaged, the bottom end of
lower rods (Ref. 40 & 66) should be flush
with bottom of springs (Ref. 39 & 68).
80
81
79
69
82
59
71
36
37
38
70
68
67
59
66
65
59
64
To engine
63
62
To headlight
To engine
plug
ground
1
4
74
76
Shift rod assembly
(Ref. 71) must pivot
freely on pivot blocks
(Ref. 21).
65
61
To spout
motor
2
4
5
6
3
78
4
77
4
21
75
74
73
72
Mount clutch cable
to cable support, see
Engine & Frame.
See Auger Housing and
Chute Group - 38"
56
58
59
60
10
8
7
28
2727
Torque to
19 - 29 ft-lbs.
84
Mount bushin gs (Ref . 78)
with flange on inside of
brackets, 3 places.
48
43
57
Slot towards
rear of unit.
986724
11
12
9
14
15
17
16
18
12
34
40
47
48
46
43
49
50
53
13
19
20
12
26
22
4
23
4
5
25
29
30
31
35
36
37
38
32
33
39
34
43
46
45
52
54
55
83
51
The holes in the frame for Ref. 51 are
slotted so the gear support (Ref. 45) can
be positioned to ensure the inside surface
of the gear support is tight against the
hub of the front gear (Ref. 50).
96
24
41
42
43
44
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
4
TP 400-4155-01-LW-S
Handles and Controls Group - 1060, 1170, 1280 & 1390 Models
PART NO. DESCRIPTIONREF NO QTY.
1 1727128 1 HANDLE, Clutch R.H.
2 1668608 2 GRIP, Handle Clutch, Black
3 1928732 1 CAPSCREW, Hex Washer Head Taptite #10-24 x 1
4 1668185 5 BUSHING, 1/2 ID x 3/4 OD x 1/4, Nylon
5 1725205A 2 LEVER & TUBE ASSEMBLY, Clutch
6 1960471 4 CAPSCREW, Hex Washer Head Taptite #12-24 x 1
7 1705899 1 GUIDE, Control
8 1726422 2 RIVET, Pop (1280 & 1390 Models Only)
9 1726317 2 GRIP, Black Soft 1" (9560, 1060 & 1170 Models Only)
9 1723965 2 HAND GRIP, Heated 1" (1280 & 1390 Models Only)
10 1667800C 1 DASHBOARD
11 1724489 1 PLUG, Button (1390 Models Only)
12 1925592 6 CAPSCREW, Hex Washer Head Taptite 1/4-20 x 3/4
13 1930641 4 NUT, Hex Flange Whiz Lock 1/4-20
14 1935450 4 CAPSCREW, Hex Washer Head, 1/4-20 x 3/4 G5
15 1933689 1 CAPSCREW, Hex Flange Whiz Lock, 5/16-18 x 1-1/2
16 1678579 1 SPACER, 21/64 ID x 13/16 OD x 15/16
17 1705898 1 LATCH, Control
18 1701342 1 SPRING, Compression
19 1960686 1 NUT, Hex Flange 5/16-18 ESNA
20 1726672C 1 HANDLE ASSEMBLY, Channel
21 1723935A 1 BRACKET, Shift Control
22 1718791 1 CABLE & HANDLE ASSEMBLY, Clutch L.H.
23 1677453 1 ROD, Control 2" Flat
24 1727127 1 HANDLE, Clutch L.H.
25 1725702 1 SCREW, Pan Head Torx #10 x 1/2 Thick Cut
26 1664022 1 GROMMET, 1/2
27 2834683 1 CLIP, Wire
28 1933896 1 NUT, Hex Lock 10-24 with Nylon Insert NC3B
29 1678392 1 SPACER, 17/64 ID x 3/8 OD x 21/64
30 1726728 1 CLIP, Clean Out Tool
31 1960589 1 SCREW, Phillips #10-24 x 3/4
32 7075909 1 TOOL, Clean Out
33 1726727A 1 BRACKET, Clean Out Tool
34 1930591 6 CAPSCREW, Hex Flange Whiz Lock, 5/16-18 x 3/4
35 1668121 1 ROD, Clutch, 17-5/16
36 2828704 2 NUT, Hex Machine Screw 10-24 NC-2B LH YEL
37 2108775 2 TURNBUCKLE, 2-1/4 Long #10-24NC (L.H. & R.H.)
38 1916621 2 NUT, Hex Machine Screw 10-24 NC-2B
39 1707452 1 SPRING, Extension 3-11/32 Long
40 1668526 1 ROD, Clutch, 6-5/16 Long
41 1960093 1 NUT, Push Pal (Used on all models Except 1390 Models)
42 1714084 1 KNOB, Spinner, Soft (9560, 1060, 1170 & 1280 Models Only)
43 1667588 4 BUSHING, 3/8 ID x 7/16 OD x 13/64, Nylon (9560, 1060, 1170 & 1280 Models Only)
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
5
TP 400-4155-01-LW-S
Handles and Controls Group - 1060, 1170, 1280 & 1390 Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Linkage adjustment for traction and
auger drive with power boost: with
drive levers engaged, the bottom end of
lower rods (Ref. 40 & 66) should be flush
with bottom of springs (Ref. 39 & 68).
80
81
79
69
82
59
71
36
37
38
70
68
67
59
66
65
59
64
To engine
63
62
To headlight
To engine
plug
ground
1
4
74
76
Shift rod assembly
(Ref. 71) must pivot
freely on pivot blocks
(Ref. 21).
65
61
To spout
motor
2
4
5
6
3
78
4
77
4
21
75
74
73
72
Mount clutch cable
to cable support, see
Engine & Frame.
See Auger Housing and
Chute Group - 38"
56
58
59
60
10
8
7
28
2727
Torque to
19 - 29 ft-lbs.
84
Mount bushin gs (Ref . 78)
with flange on inside of
brackets, 3 places.
48
43
57
Slot towards
rear of unit.
986724
11
12
9
14
15
17
16
18
12
34
40
47
48
46
43
49
50
53
13
19
20
12
26
22
4
23
4
5
25
29
30
31
35
36
37
38
32
33
39
34
43
46
45
52
54
55
83
51
The holes in the frame for Ref. 51 are
slotted so the gear support (Ref. 45) can
be positioned to ensure the inside surface
of the gear support is tight against the
hub of the front gear (Ref. 50).
96
24
41
42
43
44
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
6
TP 400-4155-01-LW-S
Handles and Controls Group - 1060, 1170, 1280 & 1390 Models
PART NO. DESCRIPTIONREF NO QTY.
44 1715658 1 ROD, Chute Control, 27" Long (9560, 1060, 1170 & 1280 Models Only)
45 1718793 1 SUPPORT, Gear (9560, 1060, 1170 & 1280 Models Only)
46 1718593 2 GEAR, Powered Metal (9560, 1060, 1170 & 1280 Models Only)
47 1918452 1 PIN, Cotter 1/8 x 1 (9560, 1060, 1170 & 1280 Models Only)
48 2816168 2 PIN, Spring 1/8 x 3/4 (9560, 1060, 1170 & 1280 Models Only)
49 1725283 1 ROD, Chute Worm, 18 Long (9560, 1060, 1170 & 1280 Models Only)
50 1668186 1 WORM, Chute, L.H. (9560, 1060, 1170 & 1280 Models Only)
51 1960252 2 CARRIAGE BOLT, 1/4-20 x 5/8 G5 (9560, 1060, 1170 & 1280 Models Only)
52 1960294 2 NUT, Hex Flange Whiz Lock, 1/4-20 Small (9560, 1060, 1170 & 1280 Models Only)
53 1611911 1 SUPPORT, Worm (9560, 1060, 1170 & 1280 Models Only)
54 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 G5 (9560, 1060, 1170 & 1280 Models Only)
55 1960684 1 NUT, Hex KEPS Conical Washer, 5/16-18 (9560, 1060, 1170 & 1280 Models Only)
56 1723967 1 SWITCH, Hand Warmer (1280 & 1390 Models Only)
57 1923341 1 CAPSCREW, Hex Head, 1/4-20 x 3/4 G5 (1280 & 1390 Models Only)
58 1724037 1 RESISTOR BLOCK, Male Terminal (1280 & 1390 Models Only)
59 1960685 4 NUT, Hex KEPS, 1/4-20 Conical Washer
60 2172434 1 CLIP, Wire (Spout Rotator Models Only)
61 1725439 1 HARNESS, Wiring (Handwarmer Models Only)
61 1725409 1 HARNESS, Wiring (Handwarmer & Spout Rotator Models Only)
62 2825094 3 TIE, Self Locking 7-5/16 (1280 & 1390 Models Only)
63 1722460 1 PIN, Quick
64 1666255 1 ROD, Lower Shift 15-21/64 Long
65 1931317 2 CARRIAGE BOLT, 1/4-20 x 3/4 G5
66 1702004 1 ROD, Lower Clutch
67 1726304 1 ROD, Upper Shift 11-3/8 Long
68 1701996 1 SPRING, Extension 4-3/4 Long
69 1702485 1 ROD, Upper Clutch
70 1713844 1 KNOB, Hole
71 1714120 1 ROD & CLEVIS ASSEMBLY, Shift
72 1960705 1 CAPSCREW, Hex Flange Whiz Lock 1/4-20 x 2-1/4
73 1668681 1 WASHER, Curved
74 1668524 2 BLOCK, Pivot, Powdered Metal
75 1924361 1 WASHER, 1/2
76 1703043 1 ROD & ARM ASSEMBLY, Pivot
77 1960074 1 CLIP, Hair Pin
78 1702663 1 ROD, Clutch 5-11/32 Long
79 1933689 1 CAPSCREW, Hex Flange Whiz Lock 5/16-18 x 1-1/2
80 1919326 1 WASHER, 5/16
81 1702662 1 LEVER, Clutch
82 1702552 1 SPACER, 21/64 ID x 3/4 OD x 53/64, Powdered Metal
83 1960518 2 NUT, Push for 1/4 Diameter Thread
84 1701011 1 TIE, Self Locking, 15" (Spout Rotator Models Only)
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
7
TP 400-4155-01-LW-S
Handles and Controls Group - 9560 Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
8
6
4
5
3
1
2
986728
9
10
11
7
Insert shift rod (Ref. 58)
into outter hole of Ref. 64.
65
64
54
54
63
58
57
56
12
63
62
61
Apply adhesive to
secure grips.
13
66
35
67
56
60
Must slide freely in
dash assembly (Ref 13).
Apply lubricant as required.
17
15
14
68
16
20
23
1625
18
19
21
12
22
28
Mount bushings (Ref. 14)
with flange on inside of
brackets, 3 places.
49
50
14
59
Shift rod assembly (Ref. 61)
57
must pivot freely on
56
54
53
52
49
52
14
51
46
pivot blocks, (Ref. 63).
55
14
45
47
Slot towards
rear of unit.
48
41
40
42
43
44
The holes in the frame for Ref. 44 are
slotted so the gear support (Ref. 42) can
be positioned to ensure the inside surface
of the gear support is tight against the
hub of the front gear (Ref. 50).
26
39
24
Must pivot freely
34
36
38
on capscrew (Ref 27).
35
Apply lubricant as required.
36
24
27
30
31
33
37
29
32
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
8
TP 400-4155-01-LW-S
Handles and Controls Group - 9560 Models
PART NO. DESCRIPTIONREF NO QTY.
1 1726833 1 CABLE AND SPRING ASSEMBLY, R.H. Auger
2 1701996 1 SPRING, Torsion
3 1727087A 1 HANDLE, Tube, R.H.
4 1922127 1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4 G5
5 1921221 3 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G5
6 1960671 2 SCREW, Pan Head Torx, 1/4-20 x 3/4, Thread Cutting
7 1715654 2 SPACER, 1/4ID x 25/64OD x 11/64LG
8 1922837 2 CAPSCREW, Hex Head, 1/4-20 x 1-1/2 G5
9 1722638 1 HANDLE, Clutch R.H.
10 1715655 2 SPACER
11 1923358 2 NUT, Hex Centerlock, 1/4-20
12 1726317 2 GRIP
13 1726983A 1 DASH AND SUPPORT ASSEMBLY, Tubular
14 1667588 4 BUSHING, 47/125ID x 437/1000OD x 1/5LG
15 1714084 1 KNOB, Spinner
16 1960093 1 NUT, Push Pal, 3/8" Diameter Stud Capped
17 1722633 1 ROD AND SPRING ASSEMBLY, w/Pin
18 1722690 1 SPRING, Complete
19 1960519 1 PUSH NUT, Stud Cap, 1/2
20 1722630 1 ROD, 4/25" Diameter, E-Coat
21 1722667 1 HANDLE, Clutch L.H.
22 1727086A 1 HANDLE, Tube, L.H.
23 1960662 1 CAPSCREW, Hex Head, 1/4-20 x 2 G5
24 1920397 2 NUT, Hex Lock ESNA Light, 1/4-20NC-3B
25 1921319 2 WASHER, 1/4
26 1933896 1 NUT, Hex Lock, 10-24
27 1722631A 1 LEVER, Pivot
28 1718791 1 CABLE AND HANDLE ASSEMBLY, Clutch
29 1725702 1 SCREW, Pan Head Torx, #10 x 1/2 Thread Cut
30 1726995 1 SPACER, 1-1/4 LG Beveled End
31 1726728 1 CLIP, Snow Stick
32 1960727 1 SCREW, Hex Flange Slot, #10-24 x 2-1/2
33 7075909 1 STICK, Snow Removal
34 1720452 2 CLAMP, Saddle Snow Handle E-Coat
35 1726727A 1 BRACKET, Clean Out Tool
36 1917356 4 LOCKWASHER, Spring, 5/16
37 1921978 2 CAPSCREW, Hex Head 5/16-18 x 2 G5
38 1930591 2 SCREW, Hex Whiz Lock Flange, 5/16-18 x 3/4
39 1726832 1 CABLE AND SPRING ASSEMBLY, L.H. Traction
40 1707452 1 SPRING, Extension
41 1727088 1 ROD, 3/8" Diameter, 26" Long
42 1718793 1 SUPPORT, Gear
43 1960518 2 NUT, Push for 1/4 Diameter Thread
44 1960252 2 CARRIAGE BOLT, 1/4-20 x 5/8 G5
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
9
TP 400-4155-01-LW-S
Handles and Controls Group - 9560 Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
8
6
4
5
3
1
2
986728
9
10
11
7
Insert shift rod (Ref. 58)
into outter hole of Ref. 64.
65
64
54
54
63
58
57
56
12
63
62
61
Apply adhesive to
secure grips.
13
66
35
67
56
60
Must slide freely in
dash assembly (Ref 13).
Apply lubricant as required.
17
15
14
68
16
20
23
1625
18
19
21
12
22
28
Mount bushings (Ref. 14)
with flange on inside of
brackets, 3 places.
49
50
14
59
Shift rod assembly (Ref. 61)
57
must pivot freely on
56
54
53
52
49
52
14
51
46
pivot blocks, (Ref. 63).
55
14
45
47
Slot towards
rear of unit.
48
41
40
42
43
44
The holes in the frame for Ref. 44 are
slotted so the gear support (Ref. 42) can
be positioned to ensure the inside surface
of the gear support is tight against the
hub of the front gear (Ref. 50).
26
39
24
Must pivot freely
34
36
38
on capscrew (Ref 27).
35
Apply lubricant as required.
36
24
27
30
31
33
37
29
32
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
10
TP 400-4155-01-LW-S
Handles and Controls Group - 9560 Models
PART NO. DESCRIPTIONREF NO QTY.
45 1960294 2 NUT, Hex Flange, 1/4-20, Whiz Lock Small
46 1611911 1 SUPPORT, Worm
47 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 G5
48 1960684 1 NUT, Hex Keps, 5/16-18, Conical Washer
49 2816168 2 PIN, Spring 1/8 x 3/4
50 1668186 1 WORM, Chute, L.H.
51 1725283 1 ROD, 3/8" Diameter, Chute Worm E-Coat
52 1718593 2 GEAR, Powdered Metal, Metafusion
53 1918452 1 PIN, Cotter 1/4 x 1
54 1722460 1 PIN, Quick
55 1666255 1 ROD, 3/4" Diameter
56 1960685 3 NUT, Hex KEPS, 1/4-20, Conical Washer
57 1931317 2 CARRIAGE BOLT, 1/4-20 x 3/4 G5
58 1726304 1 ROD, 3/4" Diameter, Shift Upper, 11-19/50 Long
59 1726734 1 KNOB, Intermediate Thread, 3/8-16
60 1960705 1 SCREW, Hex Whiz Lock Flange, 1/4-20 x 2-1/4
61 1668523 1 ROD AND CLEVIS ASSEMBLY, Shift, Threaded
62 1924361 1 WASHER, 1/2
63 1668524 2 BLOCK, Pivot, 3/4 x 3/4, Powdered Metal
64 1720240 1 ROD AND ARM ASSEMBLY, Pivot
65 1715123 1 SPRING, Torsion
66 1960074 1 CLIP, Hair Pin
67 1668185 2 BUSHING, 1/2ID x 3/4OD x 1/4LG
68 1960686 4 NUT, Hex Flange, 5/16-18 ESNA
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
11
TP 400-4155-01-LW-S
Engine and Frame Group with Power Boost
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Long hub of idler
pulley (Ref. 3) to
1
2
Hook one end of spring (Ref. 7)
into top hole of roller arm (Ref. 6)
and other end into top hole of
the idler arm assembly in the
Traction Drive Group.
61
60
59
58
57
52
9
be toward idler
arm (Ref. 6).
3
62
55
54
53
Position idler pull ey (Ref. 14 )
at center of slot in clutch arm
(Ref. 10).
14
13
11
10
4
34
8
7
6
5
56
986732
17
21
43
19
20
Hook one end of spring (Ref. 16)
over clutch rod assembly (Ref. 10)
between tabs and other end into
slot in frame.
22
27
28
39
23
24
25
26
29
30
40
41
15
18
16
8
12
35
1433
1432
36
31
37
38
44
Torque to
10-14 ft. lbs. or
14-20 N m
3551
3549
3550
45
48
Position belt stops 1/16 - 1/8
from belt when auger clutch is engaged.
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
12
47
29
44
45
Right rear bolt.
46
Torque (4) Engine
Bolts to 17 - 21 ft. lbs.
or 23 - 29 N m
42
TP 400-4155-01-LW-S
Engine and Frame Group with Power Boost
PART NO. DESCRIPTIONREF NO QTY.
1 1700415 1 V-BELT, 3L (Used on all models Except 1390 Models)
1 1672732 1 V-BELT, 3L (Used Only on 1390 Models)
2 1928731 1 NUT, Hex, Toplock, Jam, 3/8-16
3 1668477 1 PULLEY, Idler
4 1960647 1 SCREW, Hex Head, 3/8-16 x 1-1/2
5 1665994 1 PIN, Flat Head Drilled
6 1703046A 2 ARM, Idler, 5-3/4 LG
7 1727149 1 SPRING, Extension
8 1722460 1 PIN, Quick
9 1676460 2 V-BELT, HA (Used on all models Except 1390 Models)
9 1701257 1 V-BELT, HA (Used Only on 1390 Models)
10 1727058A 1 ROD AND ARM ASSEMBLY, Clutch, Brake w/Pad
11 1669313 1 PAD, Brake
12 2825160 1 RIVET, Pop
13 1928352 1 NUT, Hex Flange, 3/8-16 Whiz Lock Large
14 1726348 1 PULLEY, Idler
15 2860709 1 SCREW, Hex Whiz Lock Flange, 3/8-16 x 1-3/4
16 1727059 1 SPRING, Extension
17 1725287 2 COVER, Belt
18 1935255 1 NUT, Speed, 5/16-18, Lug Type
19 2820426 2 LOCKWASHER, External Tooth, 5/16
20 1918249 2 SCREW, Truss head Slotted, 5/16-18 x 3/4
21 1724064 1 CORD, Electric Extension
22 1726568C 4 FRAME ASSEMBLY, Chain/Tube Handles
23 1931317 1 CARRIAGE BOLT, 1/4-20 x 3/4 G5
24 1960685 2 NUT, Hex KEPS, 1/4-20, Conical Washer
25 1720404A 4 SUPPORT, Clutch Cable, 16GA
26 1930591 1 SCREW, Hex Whiz Lock Flange, 5/16-18 x 3/4
27 1664847 1 SCREW, Hex Washer Head Taptite, 5/16-18 x 3/4
28 1930595 1 SCREW, Hex Whiz, 31/100-18 x 1-1/4
29 1726870C 4 COVER, Bottom Frame, 20GA
30 1925003 1 SCREW, Hex Washer Head Taptite, 1/4-20 x 1/2
31 1727004A 2 SUPPORT, Tie Bar
32 1927557 4 NUT, Hex Flange, 5/16-18, Whiz Lock Large
33 1919326 1 WASHER, Flat, 11/32 x 3/4 x 1/16
34 1923362 1 NUT, Hex Centerlock, 5/16-18
35 1702969 1 BELT STOP
36 1929477 1 SCREW, Hex Washer Head Taptite, #10-24 x 1/2
37 1725664A 1 GUARD, Muffler, 18GA
38 * 1 ENGINE, 9.5HP B&S Electric Start Model: 20G4140 Type: 111E1
38 * 1 ENGINE, 9.5HP B&S Electric Start (CE) Model: 20G4160 Type: 110E1
39 1726942 2 HOSE, Oil Drain, w/Fittings
40 1664847 1 CAPSCREW, Hex Washer Head, 5/16-18 x 3/4
41 1727068 1 CLIP, "J"
Footnotes
Note* See your local Briggs & Stratton distributor for Parts & Service.
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
13
TP 400-4155-01-LW-S
Engine and Frame Group with Power Boost
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Long hub of idler
pulley (Ref. 3) to
1
2
Hook one end of spring (Ref. 7)
into top hole of roller arm (Ref. 6)
and other end into top hole of
the idler arm assembly in the
Traction Drive Group.
61
60
59
58
57
52
9
be toward idler
arm (Ref. 6).
3
62
55
54
53
Position idler pull ey (Ref. 14 )
at center of slot in clutch arm
(Ref. 10).
14
13
11
10
4
34
8
7
6
5
56
986732
17
21
43
19
20
Hook one end of spring (Ref. 16)
over clutch rod assembly (Ref. 10)
between tabs and other end into
slot in frame.
22
27
28
39
23
24
25
26
29
30
40
41
15
18
16
8
12
35
1433
1432
36
31
37
38
44
Torque to
10-14 ft. lbs. or
14-20 N m
3551
3549
3550
45
48
Position belt stops 1/16 - 1/8
from belt when auger clutch is engaged.
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
14
47
29
44
45
Right rear bolt.
46
Torque (4) Engine
Bolts to 17 - 21 ft. lbs.
or 23 - 29 N m
42
TP 400-4155-01-LW-S
Engine and Frame Group with Power Boost
PART NO. DESCRIPTIONREF NO QTY.
42 1727033 1 SCREW, Muffler Deflector
43 1727032 3 DEFLECTOR, Rain Guard, B&S Snow Muffler
44 2831277 3 NUT, Hex Flange, 5/16-18, Whiz Lock Small
45 1725326C 1 SUPPORT, Engine Riser (Used on all models Except 1390 Models)
46 1935159 1 CAPSCREW, Hex Whiz Lock Flange, 5/16-18 x 2-1/4 (Used on all models Except
1390 Models)
46 1921221 1 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G5 (Used Only on 1390 Models)
47 2860551 4 CAPSCREW, Hex Washer Head Taptite, 5/16-18 x 2-1/2 (Used on all models Except
1390 Models)
47 2822127 3 CAPSCREW, Hex Head 5/16-18 x 1-3/4 G5 (Used Only on 1390 Models)
48 1668174 1 STOP, Belt
49 1919326 2 WASHER, 5/16
50 1917356 2 LOCKWASHER, Spring, 5/16
51 1921515 1 CAPSCREW, Hex Head, 5/16-24 x 3/4 G5
52 1701849 1 SPRING, Compression
53 1702425 1 SPRING, Compression
54 1701818 1 WASHER, Thrust
55 1726869 1 PULLEY HALF, Middle
56 1726868 1 PULLEY HALF, Inside
57 1922128 1 CAPSCREW, Hex Head, 3/8-24 x 1-1/2 G8
58 1916965 1 LOCKWASHER, Spring, 3/8
59 1922755 1 WASHER, 3/8
60 1726864 1 PULLEY HALF, Outside
61 1726863 1 PULLEY HALF, Middle
62 1701825 1 WICK, Felt, Oil
Footnotes
Note* See your local Briggs & Stratton distributor for Parts & Service.
The above parts group applies to the following Mfg. Nos.:
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694598 - 1060M
1694599 - 1170M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694600 - 1280M
1694601 - 1390M
15
TP 400-4155-01-LW-S
Engine and Frame Group without Power Boost
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Long hub of idler
pulley (Ref. 3) to
1
3
2
9
be toward idler
arm (Ref. 6).
Position idler pull ey (Ref. 14 )
at center of slot in clutch arm
(Ref. 10).
14
13
11
10
4
8
7
6
5
12
17
15
8
32
986730
21
19
20
18
16
31
30
33
34
Hook one end of spring (Ref. 16)
over clutch rod assembly (Ref. 10)
between tabs and other end into
slot in frame.
22
27
23
24
25
26
28
Hook one end of spring (Ref. 7)
into top hole of roller arm (Ref. 6)
and other end into top hole of the idler
arm assembly in the Traction Drive Group.
53
52
51
50
49
48
Torque to
10-14 ft. lbs. or
14-20 N m
3547
3545
3546
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
44
Right rear bo lt.
16
43
29
36
37
35
39
40
29
40
41
Torque (4) Engine
Bolts to 17 - 21 ft. lbs.
or 23 - 29 N m
42
38
TP 400-4155-01-LW-S
Engine and Frame Group without Power Boost
PART NO. DESCRIPTIONREF NO QTY.
1 1700415 1 V-BELT, 3L (Used on all models Except 1390 Models)
1 1672732 1 V-BELT, 3L (Used Only on 1390 Models)
2 1928731 1 NUT, Hex, Toplock, Jam, 3/8-16
3 1668477 1 PULLEY, Idler
4 1960647 1 SCREW, Hex Head, 3/8-16 x 1-1/2
5 1665994 1 PIN, Flat Head Drilled
6 1703046A 2 ARM, Idler, 5-3/4 LG
7 1727149 1 SPRING, Extension
8 1722460 1 PIN, Quick
9 1725416 2 V-BELT, HA (Used on all models Except 1390 Models)
9 1666655 1 V-BELT, HA (Used Only on 1390 Models)
10 1727058A 1 ROD AND ARM ASSEMBLY, Clutch, Brake w/Pad
11 1669313 1 PAD, Brake
12 2825160 1 RIVET, Pop
13 1928352 1 NUT, Hex Flange, 3/8-16 Whiz Lock Large
14 1726348 1 PULLEY, Idler
15 2860709 1 SCREW, Hex Whiz Lock Flange, 3/8-16 x 1-3/4
16 1727059 1 SPRING, Extension
17 1725287 2 COVER, Belt
18 1935255 1 NUT, Speed, 5/16-18, Lug Type
19 2820426 2 LOCKWASHER, External Tooth, 5/16
20 1918249 2 SCREW, Truss head Slotted, 5/16-18 x 3/4
21 1724064 1 CORD, Electric Extension
22 1726568D 4 FRAME ASSEMBLY, Chain/Tube Handles
23 1931317 1 CARRIAGE BOLT, 1/4-20 x 3/4 G5
24 1960685 2 NUT, Hex KEPS, 1/4-20, Conical Washer
25 1720404A 4 SUPPORT, Clutch Cable, 16GA
26 1930591 1 SCREW, Hex Whiz Lock Flange, 5/16-18 x 3/4
27 1664847 1 SCREW, Hex Washer Head Taptite, 5/16-18 x 3/4
28 1726870D 4 COVER, Bottom Frame, 20GA
29 1925003 1 SCREW, Hex Washer Head Taptite, 1/4-20 x 1/2
30 41727004 2 SUPPORT, Tie Bar
31 1927557 4 NUT, Hex Flange, 5/16-18, Whiz Lock Large
32 1725664A 1 GUARD, Muffler, 18GA
33 1929477 1 SCREW, Hex Washer Head Taptite, #10-24 x 1/2
34 * 1 ENGINE, 9.5HP B&S Electric Start Model: 20G4140 Type: 111E1
34 * 1 ENGINE, 9.5HP B&S Electric Start (CE) Model: 20G4160 Type: 110E1
35 1726942 2 HOSE, Oil Drain, w/Fittings
36 1664847 1 CAPSCREW, Hex Washer Head, 5/16-18 x 3/4
37 1727068 1 CLIP, "J"
38 1727033 1 SCREW, Muffler Deflector
39 1727032 3 DEFLECTOR, Rain Guard, B&S Snow Muffler
40 2831277 5 NUT, Hex Flange, 5/16-18, Whiz Lock Small (Quantity 4 used only on 9560 Models)
41 1725326C 1 SUPPORT, Engine Riser (Used on all models Except 1390 Models)
Footnotes
Note* See your local Briggs & Stratton distributor for Parts & Service.
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
17
TP 400-4155-01-LW-S
Engine and Frame Group without Power Boost
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Long hub of idler
pulley (Ref. 3) to
1
3
2
9
be toward idler
arm (Ref. 6).
Position idler pull ey (Ref. 14 )
at center of slot in clutch arm
(Ref. 10).
14
13
11
10
4
8
7
6
5
12
17
15
8
32
986730
21
19
20
18
16
31
30
33
34
Hook one end of spring (Ref. 16)
over clutch rod assembly (Ref. 10)
between tabs and other end into
slot in frame.
22
27
23
24
25
26
28
Hook one end of spring (Ref. 7)
into top hole of roller arm (Ref. 6)
and other end into top hole of the idler
arm assembly in the Traction Drive Group.
53
52
51
50
49
48
Torque to
10-14 ft. lbs. or
14-20 N m
3547
3545
3546
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
44
Right rear bo lt.
18
43
29
36
37
35
39
40
29
40
41
Torque (4) Engine
Bolts to 17 - 21 ft. lbs.
or 23 - 29 N m
42
38
TP 400-4155-01-LW-S
Engine and Frame Group without Power Boost
PART NO. DESCRIPTIONREF NO QTY.
42 1935159 1 CAPSCREW, Hex Whiz Lock Flange, 5/16-18 x 2-1/4 (Used on all models Except
1390 Models)
42 1921221 1 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G5 (Used only on 1390 Models)
43 2860551 4 CAPSCREW, Hex Washer Head Taptite, 5/16-18 x 2-1/2 (Used on all models Except
1390 Models)
43 2822127 3 CAPSCREW, Hex Head 5/16-18 x 1-3/4 G5 (Used only on 1390 Models)
44 1668174 1 STOP, Belt
45 1919326 2 WASHER, 5/16
46 1917356 2 LOCKWASHER, Spring, 5/16
47 1921515 1 CAPSCREW, Hex Head, 5/16-24 x 3/4 G5
48 1922128 1 CAPSCREW, Hex Head, 3/8-24 x 1-1/2 G8
49 1916965 1 LOCKWASHER, Spring, 3/8
50 1922755 1 WASHER, 3/8
51 1726867 1 PULLEY, Engine Outside, Powdered Metal
52 1726866 1 PULLEY, Engine Middle, Powdered Metal
53 1726865 1 PULLEY, Half Powdered Metal
Footnotes
Note* See your local Briggs & Stratton distributor for Parts & Service.
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
19
TP 400-4155-01-LW-S
Auger and Impeller Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
16
14
15
17
18
985466
End of hub to be flush
with end of rolled down
shaft (Ref. 9).
4
2
Torque to 30 -34 ft-lbs.
40 - 46 Nm.
5
7
10
10
10
11
19
6
12
13
6
8
9
Impeller to be positioned
against bearing before
tightening set screw.
3
1
2
Torque to
18-21 ft-lbs.
24 - 28 Nm.
Marked side of worm
gear must contact against
left thrust washer to assure
proper gear mesh.
Auger assembly
stamped "R".
28
Apply grease until
it appears at ends
of auger assembly
(2 places).
Auger assembly
stamped "L".
20
2929
21
26
22
18
25
23
Torque to 9 - 11 ft-lbs.
12- 15 Nm.
14
24
27
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
20
TP 400-4155-01-LW-S
Auger and Impeller Group
PART NO. DESCRIPTIONREF NO QTY.
1 1679293 1 PULLEY, w/Hub
2 1928721 2 SCREW, Set Square Head Cup Point, 5/16-18 x 1/2 G8
3 1612187A 1 IMPELLER ASSEMBLY
4 1960474 1 SCREW, Set Square Head Cup Point, 3/8-16 x 1/2 G8
5 1612093 1 SEAL, Oil 1/4" Thick
6 1612149 2 BUSHING, 377/500 ID x 1-1/10 OD x 1-1/100 LG Powerdered Metal
7 1612127 1 COLLAR, Thrust 3/4 LG
8 2836098 1 PIN, Drive Lock Type A 3/16 x 1-1/2
9 1612129 1 SHAFT, Worm 18-1/10 LG
10 2818312 3 KEY, Woodruff, 47/250 x 5/8
11 1612111 1 TUBE, 9/10 OD 39/50 ID, 7-1/2 LG
12 1612142 1 GEAR, Worm 1-3/8 LG
13 2168111 1 WASHER, Thrust
14 2118118 2 SEAL, Oil, 1/4" Thick
15 1923358 6 LOCKNUT, Hex, 1/4-20 Qauntity 8 used on 38 in. Models
16 1612137 1 CASE, Gear R.H.
17 1612124 1 GASKET, Gear Case
18 2118315 2 WASHER, Thrust
19 1612117 1 SHAFT, 16 LG Auger 3 Holes
20 2830246 1 KEY, Woodruff 1/4 x 3/4
21 1612141 1 GEAR, Worm 7/8 LG
22 1612136 1 CASE, Gear L.H.
23 1668971 1 PLUG, Pipe, Tapered, 1/8 Used on 38 in. Models
24 1960346 6 CAPSCREW, Hex Head, 1/4-20 x 2-1/4 G5 Quantity 4 used on 38 in. Models
25 1668344 2 PIN, Flat Head Drilled
26 1918447 2 PIN, Cotter 47/50 x 3/4
27 1718782A 1 AUGER ASSEMBLY, L.H. 9-1/2 LG Used on 24 in. Models
27 1718784A 1 AUGER ASSEMBLY, L.H. 11-1/2 LG Used on 28 in. Models
27 1718786A 1 AUGER ASSEMBLY, L.H. 13-1/2 LG Used on 32 in. Models
28 1718783A 1 AUGER ASSEMBLY, R.H. 9-1/2 LG Used on 24 in. Models
28 1718785A 1 AUGER ASSEMBLY, R.H. 11-1/2 LG Used on 28 in. Models
28 1718787A 1 AUGER ASSEMBLY, R.H. 13-1/2 LG Used on 32 in. Models
29 2821133 2 FITTING, Lube 1/4 Drive, No Check Ball
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
21
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 38" Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
11
8
7
5
4
Plastic washer
(Ref. 3) goes
between chute
and deflector.
3
2
47
46
48
45
986720
10
9
22
252513
14
14
12
6
15
16
1
Mount cable bracket (Ref. 23)
on right hand side of handle
using shift control bracket
hardware.
26
49
25
27
28
Coat top and bottom of
chute ring with grease.
50
32
2
44
21
20
23
18
19
17
24
When installing cable,
make sure it does not
come into contact with
muffler.
29
30
See Handles and Controls
group for Wiring Harness.
31
33
34
35
51
43
Scraper blade should
be on inside of housing.
The above parts group applies to the following Mfg. Nos.:
1694593 - 1390E
1694601 - 1390M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
42
41
22
40
36
39
37
38
29
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 38" Models
PART NO. DESCRIPTIONREF NO QTY.
1 1960001 3 SCREW, Hex Washer Head Pastite, 10-14 x 5/8
2 1931333 10 CARRIAGE BOLT, 5/16-18 x 3/4 G5
3 2860210 1 WASHER, Special, 97/250ID x 1-3/25OD x 3/100 Thick
4 1919326 1 WASHER, 5/16
5 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18NC-3B
6 1933896 2 NUT, Hex Nylon 10-24
7 1725427C 1 BRACKET, Mounting Switch Bottom
8 1725426C 1 BRACKET, Mounting Switch Top
9 1960725 1 SCREW, 10-24 x 1.75
10 1724205 1 SWITCH, Rocker Chute
11 1725696 1 BOOT, Rocker Switch
12 1727194C 1 CHUTE AND DEFLECTOR ASSEMBLY, Riveted, w/Pigtail
13 1702219 3 SPACER, Heat Treated
14 1960126 2 NUT, Push Pal, 1/4" Diameter Stud Capped
15 1611945 1 ROD, 5/16" Diameter, Spring Guide
16 1611939 1 SPRING, Complete
17 1720446 1 CABLE AND KNOB ASSEMBLY, Chute (Includes Ref. No. 18, 19, 20, 21 & 22)
18 1611989 1 BOOT, Bellows
19 1719140 1 COLLET
20 1719139 1 SEAL, Rod
21 1719138 1 KNOB
22 1960600 1 SCREW, 8-32
23 1726411A 1 SUPPORT, Cable
24 2825094 1 TIE, Self Locking
25 2860664 3 SCREW, Hex Sems Washer, 1/4-20 x 7/8
26 1724553 1 CAPLUG, For 3/4" Hole
27 1960685 1 NUT, Hex KEPS, 1/4-20, Conical Washer
28 1724604 1 PINION, 1-3/20 LG
29 1925205 9 CAPSCREW, Hex Head, 5/16-18 x 5/8 G5
30 1917356 3 LOCKWASHER, Spring, 5/16
31 1665982A 1 RETAINER, Bearing
32 2108202 1 BEARING, Ball
33 1723930A 1 COVER, Pinion, 18GA
34 1925003 2 CAPSCREW, Hex Washer Head Taptite, 1/4-20 x 1/2
35 1715885 1 MOTOR, Electric 60" Mower Rocky
36 2172279A 2 FLANGE, Bearing, w/Fitting
37 2173934 2 BEARING, Cartridge
38 2172278A 2 FLANGE, Bearing, 3/8" Deep
39 1960687 4 NUT, Hex Flange, 3/8-16 ESNA
40 1725747A 2 SKID SHOE, 7GA Formed, Heat Treated
41 61723921 1 BLADE, Scraper, 35-3/4 for 38"
42 1960702 4 CARRIAGE BOLT, 3/8-16 x 1 G5
43 1935048 15 NUT, Hex Flange, 5/16-18, Two-Way Lock GA
44 1960684 4 NUT, Hex Keps, 5/16-18, Conical Washer
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694593 - 1390E
1694601 - 1390M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
23
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 38" Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
11
8
7
5
4
Plastic washer
(Ref. 3) goes
between chute
and deflector.
3
2
47
46
48
45
986720
10
9
22
252513
14
14
12
6
15
16
1
Mount cable bracket (Ref. 23)
on right hand side of handle
using shift control bracket
hardware.
26
49
25
27
28
Coat top and bottom of
chute ring with grease.
50
32
2
44
21
20
23
18
19
17
24
When installing cable,
make sure it does not
come into contact with
muffler.
29
30
See Handles and Controls
group for Wiring Harness.
31
33
34
35
51
43
Scraper blade should
be on inside of housing.
The above parts group applies to the following Mfg. Nos.:
1694593 - 1390E
1694601 - 1390M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
42
41
24
40
36
39
37
38
29
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 38" Models
PART NO. DESCRIPTIONREF NO QTY.
45 1723902C 1 HOUSING AND IMPELLER ASSEMBLY, 38"
46 1921332 4 CAPSCREW, Hex Head, 5/16-18 x 3/4 G5
47 1715787C 2 CUTTER, Drift, 1/4" Thick, 20LG
48 1666613 3 HOLD DOWN, Chute
49 1717477A 1 GEAR, Chute
50 1930659 3 NUT, Retainer Speed, 5/16-18
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694593 - 1390E
1694601 - 1390M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
25
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 9560, 1060, 1170 & 1280 Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
5
4
3
2
Plastic washer
(Ref. 2) goes
between chute
and deflector.
and deflector.
1
Decal must cover
gap at hinge pivot.
6
986713
21
20
252511
14
7
12
22
17
13
14
16
8
Mount cable bracket (Ref. 22)
on right hand side of handle
using shift control bracket
hardware.
15
19
18
41
40
Scraper blade should
be on inside of housing.
39
42
35
37
10
9
Coat top and bottom of
chute ring with grease.
When installing cable,
23
make sure it does not
come into contact with
muffler.
muffler.
24
27
25
26
38
36
28
29
30
31
34
33
32
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694597 - 9560M
1694598 - 1060M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694599 - 1170M
1694600 - 1280M
26
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 9560, 1060, 1170 & 1280 Models
PART NO. DESCRIPTIONREF NO QTY.
1 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 G5
2 2860210 1 WASHER, Nylon
3 1919326 1 WASHER, 5/16
4 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18NC-3B (Used on all models Except 9560
Models)
5 1670578 1 KNOB, Internal Thread, 5/16 (Used Only on 9560 Models)
6 1704161C 1 CHUTE AND DEFLECTOR ASSEMBLY, Manual (Used Only on 9560 Models)
6 1720671C 1 CHUTE AND DEFLECTOR ASSEMBLY, w/Remote (Used on all models Except 9560
Models)
7 1706085 2 DECAL, Orange Strip
8 1960001 3 SCREW, Hex Washer Head Pastite, 10-14 x 5/8
9 1667865 3 SPRING, Flat
10 1666613 3 HOLD DOWN, Chute
11 1702219 3 SPACER, 17/64 ID x 3/8 OD
12 1960126 2 NUT, Push 1/4
13 1611945 1 ROD, Spring
14 1611939 1 SPRING, Compression
15 2825094 1 TIE, Self Locking (Used on all models Except 9560 Models)
16 1720446 1 CABLE AND KNOB ASSEMBLY, Chute (Includes Ref. No. 17, 18, 19, 20 & 21)
17 1611989 1 BOOT, Bellows
18 1719140 1 COLLET
19 1719139 1 SEAL, Rod
20 1719138 1 KNOB
21 1960600 1 SCREW, 8-32
22 1726411A 1 BRACKET, Cable
23 1925205 3 CAPSCREW, Hex Head, 5/16-18 x 5/8 G5
24 1917356 3 LOCKWASHER, Spring, 5/16
25 1665982A 1 RETAINER, Bearing
26 2108202 1 BEARING, Ball
27 1930659 3 NUT, Retainer Speed, 5/16-18
28 1663189 2 SPACER, Low
29 1665980 1 BEARING, Flange
30 1668639C 2 CAP, Bearing, 3-3/4OD
31 1923325 6 CAPSCREW, Hex Head 5/16-18 x 7/8 G5
32 1960687 6 NUT, Hex Flange 3/8-16 ESNA
33 1726725 2 SKID SHOE, Reversible
34 1709946A 1 BLADE, Scraper, 24" (Used Only on 9560 & 1060 Models)
34 1709947A 1 BLADE, Scraper, 28" (Used Only on 1170 Models)
34 1709948A 1 BLADE, Scraper, 32" (Used Only on 1280 Models)
35 1935048 5 NUT, Hex Flange, 5/16-18, Two-Way Lock GA (Quantity 7 Only on 1280 Models)
36 1960711 4 CARRIAGE BOLT, 3/8-16 x 3/4
37 1923362 6 NUT, Hex Centerlock, 5/16-18
38 1960699 5 CARRIAGE BOLT, 5/16-18 x 5/8 G5 (Quantity 7 Only on 1280 Models)
39 1960684 4 NUT, Hex Keps, 5/16-18, Conical Washer (Used on all models Except 9560 Models)
40 1921332 2 CAPSCREW, Hex Head, 5/16-18 x 3/4 G5 (Used on all models Except 9560 Models)
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694597 - 9560M
1694598 - 1060M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694599 - 1170M
1694600 - 1280M
27
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 9560, 1060, 1170 & 1280 Models
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
5
4
3
2
Plastic washer
(Ref. 2) goes
between chute
and deflector.
and deflector.
1
Decal must cover
gap at hinge pivot.
6
986713
21
20
252511
14
7
12
22
17
13
14
16
8
Mount cable bracket (Ref. 22)
on right hand side of handle
using shift control bracket
hardware.
15
19
18
41
40
Scraper blade should
be on inside of housing.
39
42
35
37
10
9
Coat top and bottom of
chute ring with grease.
When installing cable,
23
make sure it does not
come into contact with
muffler.
muffler.
24
27
25
26
38
36
28
29
30
31
34
33
32
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694597 - 9560M
1694598 - 1060M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694599 - 1170M
1694600 - 1280M
28
TP 400-4155-01-LW-S
Auger Housing and Chute Group - 9560, 1060, 1170 & 1280 Models
PART NO. DESCRIPTIONREF NO QTY.
42 1612184C 1 HOUSING AND IMPELLER ASSEMBLY, 24" (Used on 9560 & 1060 Models)
42 1612185C 1 HOUSING AND IMPELLER ASSEMBLY, 28" (Used on 1170 Models)
42 1612186C 1 HOUSING AND IMPELLER ASSEMBLY, 32" (Used on 1280 Models)
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694597 - 9560M
1694598 - 1060M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694599 - 1170M
1694600 - 1280M
29
TP 400-4155-01-LW-S
Traction Drive Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
2
1
1
Mount ed outside
of frame.
Be sure tie bar support is in place. Move axle to
left (as viewed from back) to take up end play.
Move set collar (Ref. 49) to right to remove end
play in pivot arm (Ref. 40). Torque set screw
(Ref. 43) to 10 - 14 ft-lbs.
48
49
2
Apply loctite
(2 places).
3
20
22
Apply grease to
bearing areas.
Mounted inside of frame.
3
Lubricate with
4
5W 50 Synthetic oil.
21
Grease I.D. teeth•
and flange.
46
44
23
45
986712
Pack groove
with grease.
5
Mount to bracket in
6
frame weldment.
10
7
8
9
18
15
24
25
16
27
15
17
8
26
28
29
20
40
41
43
42
13
12
11
14
Apply Loctite and•
Torque to 55 - 60
in-lbs. when all parts
are against hub.
19
30
3
31
32
3
Mounted
outside of
2
frame.
33
Must pivot
freely.
Hook end to
top left corner
slot of frame.
Mount ed outside
of frame.
2
1
Mount in
hole at
upper rear
corner of
frame.
34
35
1
50
Torque to•
18 - 21 ft-lbs.
52
47
Torque to
10 - 14 ft-lbs.
Assemble Ref. 40, 44 & 51
with no end play. Parts
must rotate freely.
51
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
50
53
30
33
46
54
26
39
38
57
38
55
Grease bearing
area of Ref. 57.
37
58
36
59
56
Apply anti-seize
compound to wheel hub
area of Ref. 49 & 57.
TP 400-4155-01-LW-S
Traction Drive Group
PART NO. DESCRIPTIONREF NO QTY.
1 1930601 8 SCREW, Hex Washer Head Taptite, 5/16-18 x 5/8
2 1667341 4 RETAINER, Bearing
3 1722703 4 BEARING, Ball
4 1726856 1 SHAFT, Hex
5 1921332 3 CAPSCREW, Hex Head, 5/16-18 x 3/4 G5
6 1725428 1 DISC, Friction with Insert
7 1665995 1 HUB, Friction Disc
8 1960684 6 NUT, Hex Keps, 5/16-18, Conical Washer
9 1960687 1 NUT, Hex Flange, 3/8-16 ESNA
10 1669256 1 ARM ASSEMBLY, Shift w/Bushing
11 1666114 1 BUSHING, 19/50 ID x 3/4 OD x 1-3/100 LG
12 1924940 1 WASHER, 3/8
13 1923701 1 CAPSCREW, Hex Head, 3/8-16 x 2 G5
14 1668255 1 SPRING, Extension
15 1678956 2 COLLAR, Thrust
16 1666207 1 PIN, Loop
17 1667335 1 COLLAR, Set
18 1724333 2 SCREW, Set Square Head Cup Point, 1/4-20 x 1/2
19 1726931 1 SPROCKET, 10 Tooth
20 2860164 4 WASHER, 5/8
21 1718752 1 JACKSHAFT, Double D
22 1720298 1 SPRING, Complete
23 1718689 1 CLUTCH, Sliding, 1/5LG, Powdered Metal
24 1720078A 1 ARM, Clutch
25 2827732 1 RING, Retaining Extension
26 1960114 3 WASHER, 3/4
27 1718688 1 GEAR, Stationary Clutch
28 1679556 1 SPACER, Heat Treated, 31/100 LG
29 1667330 1 SPROCKET
30 1666980 1 CHAIN, Roller
31 1718687 1 GEAR, Double D
32 1921333 3 CAPSCREW, Hex Head, 5/16-18 x 1 G5
33 1960686 2 NUT, Hex Flange, 5/16-18 ESNA
34 1700473 1 BELLCRANK
35 1666106 1 BUSHING, 11/32 ID x 3/4 OD x 1-3/50 LG
36 1922127 1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4 G5
37 1726467 1 ROD, Pivot, 9-15/100 LG
38 1722460 1 PIN, Quick
39 1725666 1 SPRING, Extension
40 1719879 1 DRIVE DISC with SPINDLE
41 2818312 1 KEY, Woodruff, 47/250 x 5/8
42 1960114 1 WASHER, 3/4
43 1924366 1 WASHER, 5/8
44 1670849 1 ARM, Pivot with Bushings & Bearings (Includes Ref. Nos. 45, 46, 47 & 48)
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
31
TP 400-4155-01-LW-S
Traction Drive Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
2
1
1
Mount ed outside
of frame.
Be sure tie bar support is in place. Move axle to
left (as viewed from back) to take up end play.
Move set collar (Ref. 49) to right to remove end
play in pivot arm (Ref. 40). Torque set screw
(Ref. 43) to 10 - 14 ft-lbs.
48
49
2
Apply loctite
(2 places).
3
20
22
Apply grease to
bearing areas.
Mounted inside of frame.
3
Lubricate with
4
5W 50 Synthetic oil.
21
Grease I.D. teeth•
and flange.
46
44
23
45
986712
Pack groove
with grease.
5
Mount to bracket in
6
frame weldment.
10
7
8
9
18
15
24
25
16
27
15
17
8
26
28
29
20
40
41
43
42
13
12
11
14
Apply Loctite and•
Torque to 55 - 60
in-lbs. when all parts
are against hub.
19
30
3
31
32
3
Mounted
outside of
2
frame.
33
Must pivot
freely.
Hook end to
top left corner
slot of frame.
Mount ed outside
of frame.
2
1
Mount in
hole at
upper rear
corner of
frame.
34
35
1
50
Torque to•
18 - 21 ft-lbs.
52
47
Torque to
10 - 14 ft-lbs.
Assemble Ref. 40, 44 & 51
with no end play. Parts
must rotate freely.
51
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
50
53
32
33
46
54
26
39
38
57
38
55
Grease bearing
area of Ref. 57.
37
58
36
59
56
Apply anti-seize
compound to wheel hub
area of Ref. 49 & 57.
TP 400-4155-01-LW-S
Traction Drive Group
PART NO. DESCRIPTIONREF NO QTY.
45 1665521 1 BEARING, Ball
46 1666425 2 BUSHING, 3/4 ID x 1 OD x 3/4 LG, Powder Metal
47 1666855 1 BUSHING, 5/8 ID x 13/16 OD x 3/4 LG, Powder Metal
48 1666001 1 BUSHING, 377/100 ID x 1-13/100 OD x 1 LG, Powdered Metal
49 1720299 1 AXLE, Round
50 1928721 2 SCREW, Set Square Head Cup Point, 5/16-18 x 1/2 G8
51 1672595A 1 PULLEY AND HUB ASSEMBLY
52 1919394 1 WASHER, 1
53 1729254 1 COLLAR, Set
54 1720300 1 GEAR AND HUB ASSEMBLY- RH
55 1930570 1 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G8
56 2821133 1 FITTING, Lube 1/4 Drive, No Check Ball
57 1720716 1 GEAR AND HUB ASSEMBLY, with Bushings
58 2860169 1 WASHER, 1-47/250
59 1720305 1 BUSHING, 1-27/200 ID x 1-157/250 OD x 3/4 LG
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
33
TP 400-4155-01-LW-S
Wheels & Tires Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
1
2
4
5
986549
3
6
10
7
6
8
4
9
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
34
TP 400-4155-01-LW-S
Wheels & Tires Group
PART NO. DESCRIPTIONREF NO QTY.
1 1921978 1 CAPSCREW, Hex Head 5/16-18 x 2 G5
2 1919438 1 NUT, Hex Lock ESNA Light 5/16-18 NC-3B
3 1726743 1 WHEEL & TIRE ASSEMBLY, Snow R.H. (Used on 24 & 28 in. Models)
3 1726745 1 WHEEL & TIRE ASSEMBLY, Snow R.H. (Used on 32 & 38 in. Models)
4 2172353 2 VALVE STEM & CAP ASSEMBLY, Air
5 1714242 1 HUB, Wheel R.H., 3-3/4 Wide 8 Diameter 3/4 ID (Used on 24 & 28 in. Models)
5 1722762 1 HUB, Wheel, 5-3/8 Wide 8 Diameter 3/4 ID (Used on 32 & 38 in. Models)
6 1727074 2 TIRE, 4.80/4.00-8, X-TRAC TL (Used on 24 & 28 in. Models)
6 1727075 2 TIRE, 16 x 6.5-8 X-TRAC TL (Used on 32 & 38 in. Models)
7 1726742 1 WHEEL & TIRE ASSEMBLY, Snow L.H. (Used on 24 & 28 in. Models)
7 1726744 1 WHEEL & TIRE ASSEMBLY, Snow L.H. (Used on 32 & 38 in. Models)
8 1720307 1 HUB, Wheel L.H., 3-3/4 Wide 8 Diameter 1-1/8 ID (Used on 24 & 28 in. Models)
8 1722761 1 HUB, Wheel 5-3/8 Wide 8 Diameter 1-1/8 ID (Used on 32 & 38 in. Models)
9 2153038 2 TUBE, Tire
10 1666969 1 PIN, KLIK, Ring
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
35
TP 400-4155-01-LW-S
Decal Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
Free Hand
Free Hand
Unlocked
Locked
Traction
Traction
1727020
Disengage
Engage
1727021
• Read the operat or's m anu al fo r oper atin g and safet y
instructions.
• Do not defeat the safety features of control. They are
for your protection.
• Keep machine properly maintain ed and serviced with
all shi eld s, g uards, and prot ecti ve devi ces in pl ace.
• Never allo w ch ild ren t o op erate sn owth rower.
• Keep area of operation clear of all persons,
especially children.
2
WAR NI N G
AVOID SERIOUS INJURY OR DEATH
• Always direct discharge chute so as to avoid
injury to persons or damage to property.
• Stop engine and disconnect spark plug wire
before servicing the unit.
• When tracti on and au ger co ntro ls are d epressed ,
the Free Han d™ control is activated. This allows
the auger co ntr ol t o be re leased , yet a uger
rotatio n wi ll cont inu e un til th e Free Han d co ntro l
is released.
4
5
986738
3
Auger
Engage
Auger
Disengage
1726946
1
3
1727023
5
6
6
1
2
4
6
7
8
7
8
9
10
9
11
12
13
10
11
1716532
15
16
15
14
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
36
TP 400-4155-01-LW-S
Decal Group
PART NO. DESCRIPTIONREF NO QTY.
1 1726945 1 DECAL, Dashboard EZ Turn L.H. (Tube Handle Models Only)
1 1727022 1 DECAL, Dashboard EZ Turn L.H. (CE)
2 1715557 1 DECAL, 5 4 3 2 1 R1 R2, Shift Pattern (Tube Handle Models Only)
3 1726946 1 DECAL, Auger Control R.H. (Tube Handle Models Only)
3 1727023 1 DECAL, Auger Control R.H. (CE)
4 1715558 1 DECAL, Simplicity (Tube Handle Models Only)
5 1722867 1 DECAL, Handle Lubrication (Tube Handle Models Only)
6 1726947 1 DECAL, Dashboard EZ Turn (Channel Handles)
6 1727024 1 DECAL, Dashboard EZ Turn (Channel Handles) (CE)
7 1714245 1 DECAL, 4 2 R1 Ground Speed, R.H. (Channel Handle Models Only)
8 1714246 1 DECAL, 5 3 1 R2, Shift Pattern, L.H. (Channel Handle Models Only)
9 1727019 1 DECAL, Stripe, 9560
9 1725376 1 DECAL, Stripe, 1060
9 1725377 1 DECAL, Stripe, 1170
9 1725378 1 DECAL, Stripe, 1280
9 1724075 1 DECAL, Stripe, 1390
10 7071880 1 DECAL, DANGER Chute Cleaning
10 1727207 1 DECAL, WARNING Chute Cleaning (CE)
11 1716532 1 DECAL, DANGER Avoid Injury from Auger
11 1727208 1 DECAL, WARNING Impeller (CE)
12 * 1 DECAL, OPEI Certified
13 1725507 1 DECAL, Power Boost (1060, 1170, 1280 & 1390 Models Only)
14 * 1 DECAL, Patent
14 * 2 LABEL, Decibel, Power MASS (CE)
15 1720454 1 DECAL, Touch Up Paint, Orange
16 * 1 DECAL, Serial I.D. Tag
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
37
TP 400-4155-01-LW-S
Headlight Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
986371
1
7
2
4
6
Existing
Hardware
5
3
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
38
TP 400-4155-01-LW-S
Headlight Group
PART NO. DESCRIPTIONREF NO QTY.
1 1725291 1 HEADLIGHT ASEMBLY
2 1701011 2 TIE, Self Locking
3 2834683 1 CLIP, Wire
4 1709256A 1 LOCKWSHER, 5/16
5 1917372 1 NUT, Hex, 5/16-18
6 1725292C 1 BRACKET
7 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694589 - 9560E
1694590 - 1060E
1694591 - 1170E
1694592 - 1280E
1694593 - 1390E
1694597 - 9560M
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
2005
1694598 - 1060M
1694599 - 1170M
1694600 - 1280M
1694601 - 1390M
39
TP 400-4155-01-LW-S
Hardware Identification & Torque Specifications
Common Hardware Types
Hex Head Capscrew
Carriage Bolt
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
second number is present it represent the
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
second number represents the
example, and the final number is the
bolt or screw (in this example 2 inches long).
, meaning the
Nominal size
inside diameter
, or
body diameter
threads per inch
body length
Washer
Lockwasher
Hex Nut
is 1/2 inch; if a
threads per inch
is 1/2 inch; the
(16 in this
of the
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
Nut, 1/2”
Inside
Diameter
1
1/4 3/4
1/2
Screw, 1/2 x 2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Body
Diameter
Body
Length
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
Size Of
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32
8-36
10-24
10-32
1/4-20
1/4-28
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
No
Marks
SAE Grade 2 SAE Grade 5 SAE Grade 8
in/lbs in/lbs
19
20
27
31
66
76
2.1
2.3
3.1
3.5
7.6 8 10.9 12 16.3
8.6 10 13.6 14 19.0
30
31
43
49
NOTES
3.4
3.5
4.9
5.5
in/lbs
41
43
60
68
420 571.2
4.6
4.9
6.8
7.7
Wrench & Fastener Size Guide
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16
5/16” Bolt or Nut
Wrench—1/2”
3/8
3/8” Bolt or Nut
Wrench—9/16”
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”
MANUFACTURING, INC.
500 N. Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
© Copyright Simplicity Manufacturing, Inc.
All Rights Reserved. Printed In USA.
2005
Loading...