Simplicity 1003, 1690237, 1690324 User Manual
Specifications and Main Features
- Types of Equipment: 1003 and 1005 Roticul
- Brand of Engine: Briggs & Stratton
- Engine Type: 80302 (1003), 130292 (1005)
- Initiation Difference: 3 Horsepower (2.23 kW) for Model 1003 and 5 Horsepower (3.73 kW) for Model 1005
- Engine Configuration: Internal Combustion, Single-Cylinder
- Cylinder Diameter: 1003 2-3/8 inches (60.3 mm) 2005 2-9/16 inches (65 mm)
- Stroke Length Measurement: 1003 1-3/4 inches (44.5 mm) and 1005 2-7/16 inches (62 mm)
- Engine Volume: 1003 at 7.75 Cu.in. (127cc) and 5 at 12.5 Cu.in. (204.8 cc)
- Shaft Position: Horizontal
- Starting System: Eyewash to Manual Rewind
- Capacitance Type: Manual
- Electronic Speed Control Device: Type which can be Adjusted Mechanically within the parameters of 1800 - 3400 rpm
- Engine Starting Mechanism: Magneto
- Lubrication Oil: Gear Impeller System
- Volume of the Crankcase: 1-1/4 Pints (.6 L)
- Volume of The Fuel Tank: 1003 - 2 Quarts (1.9 L), 1005 - 3 Quarts (2.8 L)
- Oil Free Foam Filter: Air Cleaner that Can be Used Multiple Times
- Muffler Type: Red Hook with Quiet Side Discharge And Low Back Pressure Type.
- Power Transmission Mechanism: Worm and Gear
- The Worm is Made of Steel While The Gear of Bronze Transmission Material:
- Rollers and Needle Bearing High Performance Anti-Friction Lubricated
- Double Lip Type — Dirt Excluding of the Transmission Seals:
- Greasing: Worm Gear Oil, Special, 7 Ounces (207 ml)
- Tilling Width: 610 mm or 24 inches, Standard Tine Extension Width: 895 mm or 35 1/4 inches
- Depth Adjustment: Up to 171.4 mm | Minimum: 0 mm | Maximum: 171.4 mm
- Shaft Pin Attachment: Cotter Pin
- Engine Speed: 75 RPM
- Adjustable Depth Bar:
- Right Handle: Forward Clutch
- Left Handle: Reverse Clutch (only available on Model 1005)
- Throttle: Left Handle
- Handle: adjustable height
- Frame: Steel Channel, Heavy Guage
- Model 1003: Solid Rubber, 1.75 x 8 Inches (44 x 203 mm); Model 1005: Semi-Pneumatic Tire, 1.75 x 10 Inches (44 x 254 mm)
- Length: 1.3 meters or 51 inches
- Width: 660 mm or 26 Inches without Tine extensions
- The handle’s tallest part measures 972 mm or 38-1/4 inches.
- Engine height: 27.75 inches
- Model 1003: Net Weight: 51.3kg or 113 lbs | Model 1005: 60.3kg or 133 lbs
Frequently Asked Questions
- Q: What are the horsepower ratings for Model 1003 and model 1005?
Answer: Model 1003 is rated at 2.23kW or 3 horsepower, whereas model 1005 is rated at 3.73kW or 5 horsepower.
- Q: What kind of engine does the tiller mount?
A: The Tiller is equipped with a single cylinder 4 stroke, Briggs and Stratton engine.
- Q: What is the minimum and maximum soil tilt depth?
A: The tilt range varies from 0 to a maximum of 6.73 inches with the maximum value representing the lowest depth achievable.
- Q: Is it possible to increase the maximum allowable blend width?
A: Yes, the standard blending width is standard 24 inch because of being so widely available and affordable it can reach a maximum of 35.25 inch.
- Q: Which type of belts does the tiller use?
A: For this model for belts they are comprised of worm and gear belt.
- Q: What are the steps required to power on the tiller?
A: To enable the tiller set the throttle atleast to 50% capacity, bring out the choke and rotate as much as needed and later on pull the starter rope till the engine activates.
- Q: Is there a time frame for changing engine oil?
A: From personal experience I believe that engine oil intends to be changed after first 5 hours and then every 25 hours or on yearly basis depending which one occurs first.
- Q / A: Is it possible to tiller on slope? 螺| Yes, It is always advisable to use the tiller across the slopes and do not till in steep slopes more than 20 percent (11.3 degrees) angle. Do not operate the machine on steep slopes greater than 20 percent (11.3 degrees) angle.
Q: What is the needed maintenance for the air filter?
A: Regular cleaning and oiling before reassembly is recommended of the air filter.
User Manual
Loading...