Simplex MINIPLEX 4100ES User guide

4100ES Fire Control Panels

UL, ULC, CSFM Listed; Addressable Fire Detection and Control
FM Approved * MINIPLEX Transponders

Features

4100ES Series MINIPLEX transponders allow
remotely located initiating and notification
functions:

 Transponder operation is available as standard or with

local mode operation

 Communications with the host fire alarm control panel

use the Remote Unit Interface (RUI/RUI+) format

Initiating functions include:

 Addressable device support including TrueAlarm

analog sensor compatibility

 Conventional initiating device circuit (IDC) support

Notification functions include:

 Addressable strobe and horn notification using

enhanced power delivery IDNAC SLCs

 Emergency voice/alarm communications
 Conventional DC notification appliance circuits (NACs)

Local mode operation provides:

 Default local initiating and notification operation in the

event of a communications loss with the host control panel

 Enabling of an optional Local Mode Controller with a

local alarm sounder, LED status indicators, and
keyswitch enabled control switches

 Support for IDNet addressable devices, addressable and

conventional notification appliances, and default output
tones from local amplifiers

Optional modules include:

 Digital or Analog audio riser modules for connection to

system audio signals

 Digital or analog input audio amplifiers with integral

on-board NACs

 Power supplies with or without battery chargers
 City Connect modules and RS-232 ports for printers or

maintenance terminals

 Alarm relays, auxiliary relays, additional IDC modules,

and NAC expansion modules

Cabinets are equipped with solid doors (beige or
red) and in one, two, or three bay sizes

Listed to:

 UL Std. 864, Fire Detection and Control (UOJZ), and

Smoke Control Service (UUKL)

 UL Std. 2017, Process Management Equipment (QVAX)
 UL Std. 1076, Proprietary Alarm Units-Burglar (APOU)
 UL Std. 1730, Smoke Detector Monitor (UULH)
 ULC Std. S527-99

* See pages 4 and 5 for product that is listed as UL or ULC. This product has been approved by

the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health
and Safety Code. See CSFM Listing 7165-0026:0251 for allowable values and/or conditions
concerning material presented in this document. Additional listings may be applicable; contact
your local Simplex product supplier for the latest status. Listings and approvals under Simplex
Time Recorder Co. are the property of Tyco Fire Protection Products.

MINIPLEX

transponder

IDNet addressable

devices

ALARMFIRE

PULL DOWN

Audio NAC

Emergency Operating Instructions

ALARMS

SYSTEM WARNINGS

Alarm Silenced

Fire AlarmPri ority 2 Ala rm

Supervisory Trouble

Fire Alarm

Priority 2

Supv

Trouble

Alarm

Ack

Ack

Ack

Ack

Silence

Event

More

Time

Info

Previous

Menu

On

Next

Enable

Arm

Off

Lamp

Disable

Auto

Disarm

Test

Alarm or Warning Condition

System indicator flashing. Tone On. Press Alarm Silence.

How to Acknowledge / View Events

Press ACK located under flashing indicator.
Repeat operation until all events are acknowledged.
Local tone will silence.

Addressable strobes

DISCONNECT
A.C. POWER

N

AND

C

BATTERY

O

BEFORE

A

SERVICING

I

U

T

T

U

I

SERVICING

A

BEFORE

O

BATTERY
AND

C

A.C. POWER

N

DISCONNECT

Fire Alarm Local Mode Controller

CONTROL
ENABLE

A B C

D E F G H I

ZONE1SIG2AUX

3

J K LM N OP Q R

FB4IO5IDNet

6

AC Power

S T U V W X Y Z /

P7A8L

9

'SP' ( ) , 0 :

System

NET ADDR

Reset

DEL

0

Enter C/Exit

How to Silence Building Signals

How to Reset System

Press System Reset.
Press Ack to silence tone device.

On

On

Off

Off

Auto

Auto

On

On

Off

Off

Auto

Auto

On

On

Off

Off

Auto

Auto

On

On

Off

Off

Auto

Auto

on IDNAC SLC

Alarm

Local
Mode

Alarm

Local mode

Control

Silenced

Local
Mode
Active

Alarm

Reset

Silence

Power
On

controller

4100ES Fire Alarm Control Panel

with Voice Control

Typical 4100ES MINIPLEX System One-Line Drawing

Introduction

4100ES MINIPLEX transponders connect to a host

4100ES Fire Alarm Control Panel using Simplex® remote
unit interface (RUI) communications. At the transponder,
RUI communications are received by the transponder
interface module and translated into the same internal
communications format that is used in the host control
panel.

Remotely located modules. With RUI
communications, the transponder can remotely provide
the same initiating and notification functions that occur at
the host control panel without requiring multiple long
distance wiring runs. Connections to the host panel are
low current communications and audio wiring with
distances up to 2500 ft (762 m).

Additional Reference. Refer to document S4100-0100
and the other documents listed on page 3 for additional
information concerning the extensive initiating and
notification features of the 4100ES fire alarm control
panels.

S4100-0103 5/2013

Module Bay Description

Transponder model 4100-9600 includes a bay

assembly, a power distribution interface module (PDI), a
Basic Transponder Interface Module, and an interconnect
harness. Communications with the host fire alarm control
panel are via a Remote Unit Interface (RUI) connection
that allows for up to 2500 ft (762 m) distance. RUI can
communicate with up to a total of 31 remote devices and
can be either Style 4 or Style 7 communications.

Transponder model 4100-9601 substitutes a Local
Mode Transponder Module for the Basic Transponder
Module.

Optional Expansion Bays each include a PDI and
accept a variety of optional modules (refer to list starting
on page 4).

The Battery Compartment (bottom) accepts two
batteries, up to 50 Ah, that can be mounted within the
cabinet. Battery mounting does not interfere with
available module space. A power supply with battery
charger is required for each battery set.

Packaging Availability

 Modules are power-limited (except as noted, such as

relay modules)

 Enclosure are available for one, two, or three bay sizes

or for cabinet rack mounting

 Boxes and solid doors are available in beige or red

(ordered separately)

 Up to eight close-nippled cabinets can be connected at

one transponder location (close-nippled is mounted
within 20 ft (6 m) and with interconnecting wiring
enclosed in conduit)

 Refer to document S4100-0037 for enclosure details

Local Mode Control Operation

Default Stand-Alone Operation. In the event of a

communications loss with the host fire alarm control
panel, model 4100-9601 MINIPLEX Local Mode
Transponders provide fire alarm response default
operation for its connected devices and appliances per the
following.

Input Operation. During local mode operation,
TrueAlarm initiating devices connected to the transponder
will cause an alarm at their least sensitive alarm threshold.

Local Mode Control Operation (Continued)

Notification Operation. Fire alarm conditions reported

against a fire alarm point type within a transponder in
local mode will cause all notification appliance circuits in
that transponder to:

 Sound a general alarm temporal pattern horn tone
 Activate visible notification appliance circuits

Local Mode Module Support. Local mode operation
provides support for the following 4100ES modules:

 Enhanced Power Supplies (EPS+/EPS) including

on-board IDNAC SLCs

 IDNet 1+ addressable device circuits, including those

on-board the EPS+, IDNet 1+ expansion modules, and
the Quad IDNet Isolator Module

 Expansion Power Supplies (XPS) including on-board

NACs and expansion signal modules, operated at a
temporal pattern

 4100ES amplifiers will provide their on-board horn tones

(500 Hz) at a temporal pattern through their on-board
amplifier NACs

 Firefighter Telephone control modules in local mode
Local Mode Operation Module Exclusion. Modules

not listed above but that are listed as compatible with
MINIPLEX transponders per this document, do not
interfere with local mode operation but are not supported
during local mode operation.

Local Mode Controller

Operation. During local mode operation, an optional

Local Mode Controller will indicate status (see illustration
below) and can be enabled using a keyswitch to perform
local alarm silence or reset. If alarms occurring during local
mode are reset using a Local Mode Controller, upon
restoration of communications, those alarms will not be
sent to the master controller. If alarms are still present
upon restoration of communications, then the alarm
condition will be reported and host fire alarm control panel
programmed alarm functions will occur. When
communications are re-established, the local mode
transponder restores automatically.

Mounting. Local Mode Controllers are mounted on
three-gang plates, are available in beige or red, and for
either flush or semi-flush mounting. (See page 7 for
details).

 Photoelectric sensors will alarm at 3.7%/ft smoke

obscuration

 Ionization sensors will alarm at 1.3%/ft obscuration

 Heat sensors will alarm at a fixed temperature of 135° F

(57° C)

 TrueAlarm device LEDs will be activated to indicate a

device in alarm

Fire Alarm Local Mode Controller

Local
Mode

CONTROL

ENABLE

Control

Alarm

Reset

Silence

See Operating Instruction 579-343

Alarm

Alarm

Silenced

Local
Mode
Active

Power

On

Local Mode Controller Module

2 S4100-0103 5/2013

Typical Multi-Floor MINIPLEX Audio System

ALARMFIRE

PULL DOWN

Seventh floor

Legend:

Sixth floor

Fifth floor

Fourth floor

Third floor

PULL DOWN

PULL DOWN

PULL DOWN

PULL DOWN

PULL DOWN

ALARMFIRE

DISCONNECT
A.C. POWER

N

C

AND
BATTERY

O

BEFORE

A

SERVICING

I

U

T

T

U

I

SERVICING

A

BEFORE

O

BATTERY

AND

C

N

A.C. POWER
DISCONNECT

MINIPLEX transponder

Addressable strobes
on IDNAC SLC

Speaker NAC

ALARMFIRE

TrueAlarm sensors
and IDNet/MAPNET II

ALARMFIRE

PULL DOWN

addressable circuits

Audio riser wiring,

ALARMFIRE

twisted pair

RUI communications
wiring, twisted, shielded
pair

ALARMFIRE

ALARMFIRE

DISCONNECT
A.C. POWER

N

C

AND
BATTERY

O

BEFORE

A

SERVICING

I

U

T

T

U

I

SERVICING

A

BEFORE

O

BATTERY

AND

C

A.C. POWER

N

DISCONNECT

MINIPLEX transponder

Emergency Operati ng In struct ion s

A B C

D E F G H I

ZONE1SIG2AUX

3

J K LM N O P Q R

FB4IO5IDNet

6

AC Power

ALARMS

SYSTEM WARNINGS

S T U V W X Y Z /

Alarm Silenced

Fire Alarm Pri orit y 2 Alarm

Supervisory Trouble

P7A8L

9

'SP' ( ) , 0 :

Fire Ala rm

Priority 2

Supv

Trouble

Alarm

System

NET ADDR

Ack

Ack

Ack

Ack

Silence

Reset

DEL

0

Enter C/Exit

More

Event

Previous

Info

Time

Menu

On

Next

Enable

Arm

Off

Lamp

Disable

Auto

Disarm

Test

Alarm or Warning Condition

How to Silence Building Signals

System indicator flashing. Tone On. Press Alarm Silence.

How to Reset System

How to Acknowledge / View Events

Press ACK located under flashing indicator.

Press System Reset.

Repeat operation until all events are ac know ledged.

Press Ack to silence tone device.

Local tone will silence.

Second floor

On

On

Off

Off

Auto

Auto

On

On

Off

Off

Auto

Auto

On

On

Off

Off

Auto

Auto

On

On

Off

Off

Auto

Auto

4100ES Fire Alarm Control Panel

with Voice Control

First floor

Additional 4100ES Data Sheet Reference

Subject Data Sheet Subject Data Sheet

MINIPLEX Transponders for conventional
(non-addressable) notification applications

S4100-0035

Enclosures S4100-0037 Remote Annunciators S4100-0038
LED/Switch Modules S4100-0032 Remote Battery Charger S4081-0002
4100ES Audio/Phone Modules S4100-0034 Addressable Device Compatibility S4090-0011
IDNet+ Module with Quad Isolator S4100-0046

3 S4100-0103 5/2013

Basic Panel Modules and Accessories S4100-0100
Network Display Unit (NDU) S4100-0102

MINIPLEX Transponder Product Selection

Transponder Type

Model Description Supv. Alarm

4100-9600

4100-9601

Basic Transponder, includes bay equipment with power distribution interface, and 4100-0620 Basic
Transponder Interface Module mounted in Block A

Local Mode Transponder, includes bay equipment with power distribution interface, and
4100-0625 Local Mode Transponder Interface Module mounted in Block A

in local mode 112 mA 112 mA

87 mA 87 mA

normal 87 mA 87 mA

Local Mode Controller Selection

Model Description Supv. Alarm

4601-9108 Flush mount
4601-9109 Surface mount
4601-9110 Flush mount
4601-9111 Surface mount

Red with white
lettering

Beige with black
lettering

Local Mode Controller, 3-gang plate mounted;
flush mount requires a 1 ½” (38 mm) deep
3-gang box; surface mount controllers include a
matching mounting box; see p. 7 for details

normal 12 mA 12 mA

in local mode 20 mA 60 mA

Communication Modules

Model Description Size Supv. Alarm

4100-6031

4100-6032 City Circuit, without disconnect switches N.A. 20 mA 36 mA

4100-6033 Alarm Relay, 3 Form C relays, 2 A @ 32 VDC N.A. 15 mA 37 mA

4100-6038 Dual RS-232 Interface 1 Slot 132 mA 132 mA

4100-6045 Decoder Module 3 Slots 85 mA 163 mA

4100-6048 VESDA Aspiration System Interface 1 Slot 132 mA 132 mA

4100-9816 Master Clock Interface Module with one standard RS-232 port (see S4100-0033) 1 Slot 132 mA 132 mA

Select one per
EPS+ or EPS

City Circuit, with disconnect switches

N.A. 20 mA 36 mA

Enhanced and Expansion Power Supplies and Accessories (see specification details on page 6)

Model Voltage/Listing Description Size Supv. Alarm

UL &

4100-5311 120 VAC

4100-5313 220-240 VAC UL

4100-5325 120 VAC

4100-5327 220-240 VAC UL

Dual Class A IDNAC Isolator (DCAI), converts a single Class B IDNAC SLC input to two
Class A or two Class B SLC outputs; provides short circuit isolation between each Class A

4100-6103

Model Voltage/Listing Description Size Supv. Alarm

4100-5101 120 VAC UL

4100-5103 120 VAC, Canadian ULC

4100-5102 220-240 VAC UL

4100-5115 NAC Expansion Module, 3 NACs, Class A/B, mounts on XPS only N.A. 25 mA 25 mA

4100-5152 12 VDC Power Option, 2 A maximum 1 Block 1.5 A maximum
4100-0636 Box Interconnection Harness Kit (non-audio); order one for each close-nippled cabinet

or B output circuit; connect up to two DCAI modules per IDNAC SLC input up to a
maximum of 6 DCAI modules per EPS; each isolated output SLC used requires one IDNAC
address; the total current remains controlled by the Class B input source SLC at 3 A
maximum

Enhanced Power Supply (EPS+); 9 A Enhanced Power

ULC

Supply/battery charger with 250 point IDNet 1+ interface,
3 Class B IDNAC SLCs, RUI+ isolated output communications
interface, and auxiliary relay; 120 VAC model has selectable
low battery cutout

UL &

Enhanced Power Supply (EPS); 9 A Enhanced Power

ULC

Supply/battery charger with 3 Class B IDNAC SLCs, RUI+
isolated output communications interface, and auxiliary relay;
120 VAC model has selectable low battery cutout

Expansion Power Supply (XPS); 9 A output, 3 built-in
Class A/B NACs, rated 3 A for Special Application
appliances (2 A for Regulated DC); NACs can be selected
as auxiliary power outputs, derated to 2 A for continuous
duty, total per XPS is 5 A; 4100-5103 has low battery cutout

4 Blocks

Right

Side

4 Blocks

Right

Side

1 Block 6.5 mA 6.5 mA

2 Blocks 50 mA 50 mA

217 mA 480 mA

with 200 IDNet

devices and 20

device LEDs in alarm

125 mA 220 mA

Miscellaneous Options and Accessories

Model Description

4100-1290

4100-0632 Terminal Block Utility Module with 2, 16 position terminal blocks on 4” x 5” single block, for of up to 12 AWG wire (3.31 mm2)

4100-0633 Door Tamper Switch, connects into Transponder Interface Module, one per cabinet assembly if required

4100-0634 120 VAC
4100-0635 220/230/240 VAC

4100-9837 Green LED Power-on Indicator Kit, required for ULC listing of MINIPLEX transponder; mounts on solid door knockout

2081-9031

* Standard power supply NACs can provide synchronized strobe or SmartSync, two-wire operation. Continued on next page

24 Point I/O Module for external connections, select each point as either a switch input (momentary or maintained) or an
output (for lamp/LED/relay); requires 1 Slot (refer to data sheet S4100-0032 for additional information)

Power Distribution Module (PDM) select per system voltage; one required per box

Series resistor for WSO, IDCs (N.O. water flow and tamper on same circuit, wires after water flow and before tamper) 470 Ω,
1 W, encapsulated, two 18 AWG leads (0.82 mm2), 2 ½” L x 1 ⅜” W x 1” H (64 mm x 35 mm x 25 mm)

4 S4100-0103 5/2013

MINIPLEX Transponder Product Selection (Continued)

Audio Riser Modules

Model Description Size Supv. Alarm

4100-0621

4100-0622

Dual Channel Analog Audio Riser Module; accepts one or two separate audio signals from
host control panel; mounts in Block B, is controlled by Transponder Interface Module

3-8 Channel Digital Audio Riser Module; similar to analog module, except receives and
decodes a digital input signal with up to eight audio channels; with Non-Alarm Audio input

1 Block 0 mA 15 mA

1 Block 70 mA 70 mA

Analog Emergency Voice/Alarm Communications Equipment, Constant Supervision Compatible*

Model Description Details

4100-1361 25 VRMS output

4100-1362 70.07 VRMS output NAC rating = 0.5 A

4100-1312 25 VRMS output

4100-1313 70.7 VRMS output NAC rating = 0.707 A

Flex-35, 35 W Amplifier, constant
supervision compatible

Flex-50, 50 W Amplifier, constant
supervision compatible

Includes three on-board
Class B audio NACs;
power is supplied from
an EPS+, EPS, or XPS

NAC rating = 1.4 A

NAC rating = 2 A

35 W, or 100
speakers

50 W, or 100
speakers

100 W Analog Amplifiers with Power Supply, Constant Supervision Compatible

Model/Output Voltage
25 VRMS 70.7 VRMS

4100-1314 4100-1315 120 VAC, 60 Hz UL

4100-1316 4100-1317 120 VAC, 60 Hz ULC

4100-1318 4100-1319 220/230/240 VAC, 50/60 Hz UL

4100-1320

4100-1322

4100-1324

4100-1321

4100-1323

4100-1325

Power Supply Input/Listing Description Details

Includes six, Class B audio NACs;
NAC rating = 50 W or 100 speakers
maximum; 2 A @ 25 VRMS;

1.4 A @ 70.7 VRMS

Uses the six Class B NACs of primary
amplifier

120 VAC, 60 Hz UL

120 VAC, 60 Hz ULC

220/230/240 VAC, 50/60 Hz UL

Primary

100 W

Amplifier

Backup

100 W

Amplifier

ULC
models
have low
battery
dropout
circuit

Digital Emergency Voice/Alarm Communications Equipment*

Model Description Details

4100-1363 25 VRMS output

4100-1364 70.07 VRMS output NAC rating = 0.5 A

4100-1326 25 VRMS output

4100-1327 70.7 VRMS output NAC rating = 0.707 A

Flex-35, 35 W Amplifier, constant
supervision compatible

Flex-50, 50 W Amplifier, constant
supervision compatible

Includes three on-board
Class B audio NACs;
power is supplied from
an EPS+, EPS, or XPS

NAC rating = 1.4 A

NAC rating = 2 A

35 W, or 100
speakers

50 W, or 100
speakers

100 W Digital Amplifiers with Power Supply, Constant Supervision Compatible

Model/Output Voltage
25 VRMS 70.7 VRMS

4100-1328 4100-1329 120 VAC, 60 Hz UL

4100-1330 4100-1331 120 VAC, 60 Hz ULC

4100-1332 4100-1333 220/230/240 VAC, 50/60 Hz UL

4100-1334 4100-1335 120 VAC, 60 Hz UL

4100-1336 4100-1337 120 VAC, 60 Hz ULC

4100-1338 4100-1339 220/230/240 VAC, 50/60 Hz UL

Power Supply Input/Listing Description Details

Primary

100 W

Amplifier

Backup

100 W

Amplifier

Includes six, Class B audio NACs;
NAC rating = 50 W or 100 speakers
maximum; 2 A @ 25 VRMS;

1.4 A @ 70.7 VRMS

Uses the six Class B NACs of primary
amplifier

ULC
models
have low
battery
dropout
circuit

Options for use with either Analog or Digital Amplifiers

Model Description Details and Mounting Reference

4100-1245

4100-1246

4100-1248

4100-1249

4100-1259

4100-1260

Flex-35/50 Expansion NAC Module; adds three
Class B audio NACs

Flex-35/50 Class A Adapter Module; converts
three on-board NACS to Class A operation

100 W Amplifier Expansion NAC Module; NAC
ratings = 1.5 A, 50 W, or 100 speakers max.

100 W Class A Adapter Module; NAC ratings =
2 A, 50 W, or 100 speakers max.

25 VRMS Output; NAC
rating = 2 A, 50 W, or
100 speakers max.

70.7 VRMS Output; NAC
rating = 0.707 A, 50 W,
or 100 speakers max.

Constant Supervision Adapter
for three NACs; select per
amplifier output; not
compatible with amplifier NAC
expansion modules;
deactivated when on batteries

Choose
one per

amplifier

Choose
one per
amplifier

Mounts on Flex-35/50 assembly; NAC ratings = 1.5 A, 35/50 W,
or 100 speakers maximum; Supv = 8 mA, Alarm = 60 mA

Mounts on Flex-35/50 assembly; NAC ratings = 2 A, 50 W, or
100 speakers maximum; Supv =10 mA, Alarm = 30 mA

Provides six additional Class B audio NACs, mounts on 100 W
amplifier assembly; Supv = 17 mA, Alarm = 60 mA

Converts six on-board NACs to Class A operation, mounts on
100 W amplifier assembly; Supv = 1 mA, Alarm = 60 mA

Supv = 10 mA
on batteries;
Alarm = 35 mA

Supv = 38 mA
on batteries;
Alarm = 70 mA

Converts three Class B audio NACS to
Class A or Class B Constant Supervision
NACs; mounts on Flex-35/50 or 100 W
amplifier assembly; use two for the six NACs
on 100 W amplifiers

Firefighters Telephone Options*

Model Description Size Supv. In Use

4100-1272

4100-1273 Telephone Class A Adapter Module; mounts on 4100-1272; no additional current required

* Refer to document S4100-0034 for additional audio information. Continued on next page

5 S4100-0103 5/2013

Expansion Telephone Control Module with three Class B telephone NACS; required when
telephone circuits are mounted in transponder;

1 Block 80 mA 130 mA

MINIPLEX Transponder Product Selection (Continued)

Audio Expansion Signal Module and Options

Model Description Details and Mounting Reference

Converts one NAC input to three NAC outputs; selects between two
inputs; for Flex-35/50 amplifiers only, two input NACs are required;
Single Block module mounts in expansion bay;
Supv = 20 mA; Alarm = 80 mA

Expands module capacity to six, Class B NACs;
Supv = 0.84 mA; Alarm = 60 mA

Converts 3 Class B, NACs to Class A;
Supv = 0 mA; Alarm = 30 mA

NAC rating = 1.4 A, 50 W, or 100 speakers max.;

Supv = 38 mA on batteries (constant supervision
deactivated); Alarm = 70 mA

These modules
mount on the
4100-5116;
select one
max. per
4100-5116 as
required

4100-5116

4100-1266

4100-1267

4100-1268

Expansion Signal Module; three, 1.5 A Class B NACs for
Audio applications; up to five maximum per amplifier;
NAC rating = 1.5 A, 50 W, or 100 speakers maximum

Expansion Signal Module NAC Expander; NAC rating =

1.5 A, 50 W, or 100 speakers max.
Expansion Signal Module Class A Adapter; NAC rating =

1.5 A, 50 W, or 100 speakers maximum
Expansion Signal Module Constant Supervision Adapter;

Converts 3 Class B NACs to Constant Supervision
Class B or Class A NACs; for 25 or 70.7 VRMS audio

General Audio Options

Model Description

4081-9018 End-of-line resistor harness for 70.7 VRMS NACs; 10 k, 1 W
4100-2320 Audio Bay-to-Bay Interconnection Harness Kit; order one for each audio bay addition
4100-0637 Audio Box Interconnection Harness Kit; order one for each close-nippled audio cabinet

Addressable Interface Modules

Model Description Supv. Alarm

With 250 IDNet devices, and 20 device LEDs in alarm 292 mA 510 mA

Module without devices 92 mA 115 mA

Loading per IDNet device (no LEDs on) 0.8 mA 1 mA

75 mA 115 mA

4100-3108

4100-3107

IDNet 1+ Module, 250 point capacity with
isolated output, 1 block

Quad IDNet Isolator Module; converts a single connected SLC into four isolated outputs selectable as
Class A or Class B, provides advanced diagnostics for use with retrofit wiring; dual horizontal block
module; (see data sheet S4100-0046 for additional details)

NOTE: This module is compatible with IDNet Remote Isolators

Relay Modules; Nonpower-Limited

Model Description Resistive Ratings Inductive Ratings Size Supv. Alarm

4100-3202 4 DPDT w/feedback 10 A 250 VAC 10 A 250 VAC 2 Slots 15 mA 175 mA
4100-3204 4 DPDT w/feedback 2 A 30 VDC/VAC ½ A 30 VDC/120 VAC 1 Block 15 mA 60 mA
4100-3206 8 SPDT 3 A 30 VDC/120 VAC 1 ½ A 30 VDC/120 VAC 1 Block 15 mA 190 mA

Current Calculation Notes:

1. For total supervisory current, add panel module currents to base system value and add all external panel-powered loads.

2. For total alarm current, add panel module currents to base system alarm current and add all panel SLC/NAC loads and all external

loads powered from panel power supplies.

General Specifications

Enhanced Power Supplies,

Input Power

Expansion Power Supply (XPS)

Power Supply Output
Ratings for EPS/EPS+

Power Supply Output
Ratings for XPS

(nominal 28 VDC on AC;
24 VDC on battery
backup)

Compatible Special Application Appliances

Battery Charger
Ratings for EPS/EPS+

(sealed lead-acid
batteries)

Environmental

Installation Instruction Reference 574-844, Transponder Interface Cards 579-343, Local Mode Controller

IDNAC Output Voltage Regulated 29 VRMS

Auxiliary Power Tap 2 A maximum

Auxiliary Power Tap 2 A maximum

Battery capacity range

Charger characteristics

Operating Temp. Range 32° to 120°F (0° to 49° C)

Operating Humidity Range Up to 93% RH, non-condensing @ 90° F (32° C) maximum

EPS/EPS+

100 W Amplifiers

Total Power Supply

Output Rating

Total Power Supply

Output Rating

NACs Programmed

for Auxiliary Power

and performance

120 VAC Models

220-240 VAC Models

120 VAC Models 4 A maximum @ 102 to 132 VAC, 60 Hz

220-240 VAC Models

Including module currents and auxiliary power outputs; 9 A
total for “Special Application” appliances

9 A total including module currents and auxiliary power
outputs

2 A maximum per NAC;
5 A maximum total

Simplex TrueAlert ES and TrueAlert addressable notification appliances; contact your
Simplex product representative for compatible appliances

UL listed for battery charging of 6.2 Ah up to 115 Ah (batteries larger than 50 Ah
require a remote battery cabinet); ULC listed for charging up to 50 Ah batteries

Temperature compensated, dual rate, recharges depleted batteries within 48 hours per
UL Standard 864, to 70% capacity in 12 hours per ULC Standard S527

4.6 A maximum @ 102 to 132 VAC, 50/60 Hz

2.3 A maximum @ 204 to 264 VAC, 50/60 Hz;
separate taps for 220/230/240 VAC

2 A maximum @ 204 to 264 VAC, 50/60 Hz;
separate taps for 220/230/240 VAC

Output switches to
battery backup
during mains AC
failure or brownout
conditions

Rated 19.1 to 31.1 VDC

6 S4100-0103 5/2013

Local Mode Controller Detail

4601-9109 (red) and 4601-9111 (beige); for semi-flush models 4601-9108

Matching box is supplied with surface mount models

(red) and 4601-9110 (beige), use a 1-1/2" (38 mm) minimum depth, 3-gang box

Box dimensions, 6-1/2" (165 mm)

Fire Alarm Local Mode Controller

Local
Mode

CONTROL

ENABLE

Local Mode Controller dimensions, 6-3/8" (162 mm)

Control

Alarm

Reset

Silence

See Operating Instruction 579-343

Alarm

Alarm

Silenced

Local
Mode
Acti ve

Power

On

4-1/2"

(114 mm)

1" (25.4 mm)

into box

4-5/8"

(117 mm)

1-3/4"

(44 mm)

Local Mode Controller to Transponder Wiring:

1. Wire close-nippled to transponder, maximum distance = 20 ft (6.1 m).

2. Nine wires required: 24 VDC (2), one per LED indicator (4), and one per switch (3).

3. Wire size, 18 AWG (0.82 mm² ).

Expansion Bay Module Loading Reference

Slot 1 Slot 8Slot 7Slot 6Slot 5Slot 4Slot 3Slot 2

Block A

Block B

Block C

Block D

Expansion Bay Chassis

Block E

Block F

Block G

Block H

Size Definitions:

= 4” W x 5.65” H (102 mm x 144 mm); (often

1 Block

called 4 x 5 modules)

1 Slot

= 2” W x 11.3” H (51 mm x 287 mm), typically a

motherboard with daughter card

7 S4100-0103 5/2013

Enclosure Installation Reference

Front view, box outline without door Side view with door attached

3 Bay height =

56" (1422 mm)

Door thickness

4-3/4"(121 mm)

Knockout screw/nail holes
(for semi-flush mounting)

2 Bay height =

40" (1016 mm)

1 Bay height =

22" (559 mm)

Doors can be hinged left or right

Exposed cabinet for
semi-flush mounting

1-3/8" (35 mm)

minimum

Exposed door and cabinet

for semi-flush mounting

6-1/8" (156 mm) minimum

Optional semi-flush

trim kit reference

Wall board reference
for semi-flush
mounting, 6" stud

Stud alignment
markers, each side

6" stud

4" stud

24" (610 mm)

6-29/32"

(175 mm)

11-11/16"
(296 mm)

NOTE: A system ground must be provided for Earth Detection and transient protection devices. This connection

shall be made to an approved, dedicated Earth connection per NFPA 70, Article 250, and NFPA 780.

TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. VESDA is a trademark of Xtralis Pty Ltd.

Tyco Fire Protection Products • Westminster, MA • 01441-0001 • USA S4100-0103 5/2013

www.simplexgrinnell.com

© 2013 Tyco Fire Protection Products. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.