Simplex 4100-9934, 4100-9933, 4100-9931, 4100-9932, 4100-9935 User Manual
...
Features
Existing AUTOCALL
7 Module
Equipment Box
4100ES Equipment mounts
with 7 module Retrofit Kit,
sized to fit existing box
Existing equipment
and door assembly
are removed
Fire Control Panels
UL, CSFM Listed; FM Approved; Retrofit Kits for Installing 4100ES Equipment into
MEA (NYC) Acceptance* Existing AUTOCALL
®
Control Panel Backboxes
Replace existing AUTOCALL fire alarm control
panel equipment with Simplex® 4100ES Series
products using the existing backbox:
Retrofit kits include either a solid or glass door,
retainer panels for glass door applications, and box
extension hardware
Kits are available to accommodate 1, 2, or 3 bays
of 4100ES equipment
Doors and trim are red
See notes on page 2 for installation tool
requirements
With the retrofit kits in place, standard 4100ES
equipment can be easily installed:
Existing cabinets accommodate internal battery
mounting up to 33 Ah (ref. battery 2081-9276);
50 Ah or higher battery sizes require external
cabinets
Established 4100ES module placement rules apply
Compatible existing backboxes include:
Five module, seven module, or ten module height
boxes
4” (102 mm) or 6” (152 mm) deep boxes
Boxes with or without top and bottom mounting
flanges; kit includes adapter brackets for boxes
without the flanges
UL Listed to Standard 864
Description
Retrofitting. When existing fire alarm control systems
require capacity or performance increases, it is an
opportunity to consider new product solutions. For
existing AUTOCALL fire alarm control equipment in
need of updating, these retrofit kits allow the installation
of 4100ES Series equipment to be mounted in the
installed box. By retaining the existing boxes, mechanical
and electrical impact is reduced, often significantly.
Typical Applications. Examples for these retrofit kits
include backboxes installed on surfaces that would be
costly to modify (such as marble, plaster, or concrete) or
where installed into a custom enclosure. Whether surface
mounted or semi-flush mounted, these retrofit kits can
expedite the equipment retrofit process.
Equipment Selection Reminder. Proper retrofitting
of existing equipment requires that the desired fire alarm
functions be understood in order to specify the necessary
4100ES equipment.
* This product has been approved by the California State Fire Marshal (CSFM) pursuant to
Section 13144.1 of the California Health and Safety Code. See CSFM Listing 7170-0026:251
for allowable values and/or conditions concerning material presented in this document. It is
subject to re-examination, revision, and possible cancellation. Accepted for use – City of
New York Department of Buildings – MEA35-93E. This product was not ULC listed as of
document revision date. Additional listings may be applicable; contact your local Simplex
product supplier for the latest status. Listings and approvals under Simplex Time Recorder
Co. are the property of Tyco Safety Products Westminster.
Typical Application; 7 Module Box
Retrofitted with Two-Bay 4100ES
S4100-0047-2
Red Retrofit Kits with Glass Door
Model
Existing Box Depth
Existing Box Model No.
Existing Box Capacity
4100ES Module Capacity
4100-9930
4” (102 mm)
8099-512
5 Module
One bay
4100-9931
6” (152 mm)
8099-516
4100-9932
4” (102 mm)
8099-513
7 Module
Two bay
4100-9933
6” (152 mm)
8099-514
4100-9934
6” (152 mm)
8099-515
10 Module
Three bay
Red Retrofit Kits with Solid Door
Model
Existing Box Depth
Existing Box Model No.
Existing Box Capacity
4100ES Module Capacity
4100-9935
4” (102 mm)
8099-512
5 Module
One bay
4100-9936
6” (152 mm)
8099-516
4100-9937
4” (102 mm)
8099-513
7 Module
Two bay
4100-9938
6” (152 mm)
8099-514
4100-9939
6” (152 mm)
8099-515
10 Module
Three bay
Tyco is a registered trademark of Tyco International Services GmbH and is used under license. Simplex, the Simplex logo and AUTOCALL are trademarks of Tyco International Ltd.
and its affiliates and are used under license.
Tyco Safety Products Westminster • Westminster, MA • 01441-0001 • USA
www.tycosafetyproducts-usa-wm.com
© 2011 Tyco Safety Products Westminster. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
AUTOCALL Retrofit Kit Installation Reference (for details refer to Installation Instructions 579-798)
AUTOCALL Backbox Retrofit Kit Selection
Door assembly,
glass or solid
(glass door shown)
Dress panel for
glass doors
Box extension
hardware
Existing box
4100ES bay
mounting brackets
Adapter bracket
for top of box, if
required
Adapter bracket
for bottom of
box, if required
Installation Notes:
1. Power tools are required.
2. Pilot holes must be drilled in the
flanges of the existing box using a
7/64” drill bit. Mark hole locations
using the extension hardware as a
template – remove extension
hardware before drilling.
3. Self-tapping screws fasten the
extension hardware to the box; a
medium to heavy duty power
screwdriver is recommended; an
extra long driver is recommended for
4” deep boxes.
4. Refer to Installation Instructions
579-798 for more information.
S4100-0047-2
Loading...