Simon EA-K-30/400-T-DA, EA230-K-30, EA-K-30/800-T-DA, EA-K-30/600-T-DA, EA-K-30/1000-T-DA Operating Manual

...

Download

Page 1

BA_EA(230)-K-30-xxx_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

BA EA-K-30/xxx-T(-DA) / EA230-K-30/xxx(-S) EN 1.2

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Subject to technical changes and errors. All figures are exemplary.

Only valid with the supplementary sheet: “Safety Instructions and Warranty Conditions”!

Operating ManualValid for the following article numbers:

EA-K-30/xxx-T(-DA)

•M2 5315 (DA) 400 mm stroke

•M2 5316 (DA) 600 mm stroke

•M2 5317 (DA) 800 mm stroke

•M2 5318 (DA) 1 000 mm stroke

•M2 5319 (DA) 1 200 mm stroke

EA230-K-30/xxx

•M2 5140 300 mm stroke

•M2 5141 600 mm stroke

•M2 5142 800 mm stroke

•M2 5143 1 000 mm stroke

EA230-K-30/xxx-S

•M2 5144 300 mm stroke

•M2 5145 600 mm stroke

•M2 5146 800 mm stroke

•M2 5147 1 000 mm stroke

For further information please visit

our product website

short.simon-protec.com/eaken

Page 2

BA_EA(230)-K-30-xxx_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Table of Contents

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 2

1. General ................................................................................................................................................................ 4

1.1 Foreword to this manual ....................................................................................................................................4

1.2 Intended use ....................................................................................................................................................4

1.3 EA-K-30 – Product description ...........................................................................................................................4

1.4 EA230-K-30 – Product description ......................................................................................................................4

2. Safety Regulations ............................................................................................................................................... 5

2.1 Risk assessment .............................................................................................................................................. 5

2.2 Restrictor stay .................................................................................................................................................. 5

3. Figures .................................................................................................................................................................5

4. EA-K-30 – Functions ............................................................................................................................................7

4.1 Soft-close range ............................................................................................................................................... 7

4.1.1 Speed reduction ........................................................................................................................................ 7

4.1.2 Current reduction ......................................................................................................................................7

4.2 SIMON LINK .................................................................................................................................................... 7

4.3 Configurable ranges .......................................................................................................................................... 8

5. EA230-K-30 – Functions ......................................................................................................................................8

5.1 End position cut-off while closing ........................................................................................................................ 8

5.2 End position cut-off while opening ...................................................................................................................... 8

5.3 DIP switches .................................................................................................................................................... 8

5.4 RESET ............................................................................................................................................................ 9

5.5 Teach-in run ..................................................................................................................................................... 9

5.6 Performing a teach-in run ..................................................................................................................................9

5.7 LED displays .................................................................................................................................................. 10

6. Mounting ............................................................................................................................................................ 11

6.1 Mechanical connection ....................................................................................................................................11

6.1.1 Mounting brackets ...................................................................................................................................12

6.1.2 Top bracket K-K50-OK ............................................................................................................................ 13

6.1.3 Inward opening bracket K-K30-AKI ...........................................................................................................14

6.1.4 Top bracket K-K-OK-SK ........................................................................................................................... 15

6.1.5 Inward opening top / bottom hung window, mounting on a blind frame ...........................................................15

6.1.6 Outward opening top / bottom hung window, mounting on a blind frame .........................................................15

6.1.7 Inward opening top / bottom hung window, actuator mounted on the window sash .......................................... 16

6.1.8 Inward opening bottom hung window, actuator K-K30-FLEX mounted on the window sash .............................16

6.1.9 Rotary window ........................................................................................................................................ 17

6.1.10 Calculating forces/stroke ........................................................................................................................ 18

6.1.11 Permissible pushing force on the chain .................................................................................................... 18

6.2 EA-K-30 Electrical connection ..........................................................................................................................19

6.2.1 Supply ................................................................................................................................................... 19

6.2.2 Supply / connection cable ....................................................................................................................... 19

6.2.3 Feedback signal – “F” contact .................................................................................................................. 20

6.2.4 Feedback signal – dry contact ................................................................................................................. 20

6.2.5 Feedback signal – tandem port ................................................................................................................ 20

6.2.6 Single connection – dry contact ................................................................................................................ 20

6.2.7 Single connection – “F” contact ................................................................................................................20

Page 3

BA_EA(230)-K-30-xxx_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

Table of Contents

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 3

6.2.8 DUO operation / parallel connection .......................................................................................................... 21

6.3 EA230-K-30 Electrical connection ..................................................................................................................... 22

6.4 Single connection – standard variante (EA230-K-30 / xxx) .................................................................................... 22

6.4.1 Parallel connection (EA230-K-30 / xxx) ...................................................................................................... 23

6.4.2 Synchronous connection (EA230-K-30 / xxx-S) ........................................................................................... 23

7. EA-K-30 – Technical Data .................................................................................................................................. 24

8. EA230-K-30 – Technical Data ............................................................................................................................ 26

9. Commissioning ................................................................................................................................................... 27

9.1 EA230-K-30 ................................................................................................................................................... 27

10. Troubleshooting ............................................................................................................................................... 27

10.1 EA-K-30 ....................................................................................................................................................... 27

10.2 EA230-K-30 ................................................................................................................................................. 27

11. Annex ............................................................................................................................................................... 28

11.1 Care and Maintenance .................................................................................................................................. 28

11.2 General business and delivery terms ..............................................................................................................28

11.3 Company Addresses ..................................................................................................................................... 28

11.3.1 System manufacturer ............................................................................................................................ 28

11.3.2 Germany .............................................................................................................................................. 28

11.3.3 Switzerland .......................................................................................................................................... 28

11.3.4 Hungary ............................................................................................................................................... 28

12. Manufacturer's declaration ............................................................................................................................... 28

13. EC manufacturer’s declaration (distributor) ...................................................................................................... 28

Page 4

General

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 4

Operating Manual

1. General

1.1 Foreword to this manual

This manual is intended for professional operation, installation and maintenance by trained, knowledgeable and qualified personnel (such as mechatronics engineer or electrician) and / or qualified personnel who know how to install electrical equipment.

Read this operating manual carefully and pay particular attention to the hazard warnings. Store this operating manual for future reference / maintenance. Please pay close attention to the terminal assignment, the minimum and maximum performance data (see “Technical Data”) and the installation instructions. Incorrect use or improper operation / mounting may cause loss of system functionality and damage to property and / or people.

The following symbols can be found in this manual:

 Operating procedures are marked this way.

Consequences are presented this way.

• Buttons or switches to be pressed / activated are shown

in bold.

• “Indicators” are placed in quotation marks.

1.2 Intended use

Opening units (actuators) are used for the power-operated opening and closing of building covers that are installed in walls or in roofs and are used for the ventilation of rooms or for the removal of fire smoke.

See chapter 2.1 “Risk assessment” on page 5.

1.3 EA-K-30 – Product description

The EA-K-30 / xxx-T(-DA) is an an electromotive chain actuator that can be used in accordance with Chapter 1.2 of this operating manual.

The technical features include:

• soft start

• intelligent, microprocessor-controlled overload cut-off

• low noise emission

• soft-close range

• configurable stroke and force

• double-sided connection option (EA-K-30 / xxx-T-DA) for the supply cable (with connector)

• DUO operation of two actuators1 with a connection cable, the power supply is looped through from one actuator to the other

1.4 EA230-K-30 – Product description

The EA230-K-30 / xxx(-S) is an electromotive chain actuator that can be used in accordance with Chapter 1.2 of this operating manual.

The technical features include:

• soft start

• low noise emission

•soft - close

• electronic zero point reset by means of a teach-in run in the “CLOSED” direction

• stroke programming

• synchro operation of up to eight EA230-K-30 / xxx-S actuators

INFORMATION

An information text gives you additional hints!

ATTENTION

This warning notice alerts you to potential hazards that may impact the product!

DANGER

This warning notice alerts you to potential hazards to your life or health!

ENVIRONMENT NOTICE

This notice alerts you to potential environmental hazards!

1. A minimum of one actuator is required with a double-sided connection – EA-K-30/xxx-DA.

Page 5

Safety Regulations

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 5

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

2. Safety Regulations

See supplementary sheet “Safety Instructions and Warranty Conditions”!

2.1 Risk assessment

2.2 Restrictor stay

3. Figures

Figure 1: EA-K-30/xxx-T(-DA) chain actuator

Figure 2: EA230-K-30/xxx(-S) chain actuator

INFORMATION

Perform a risk assessment according to the application (e.g. the mounted system).

Information can be found in the guidance sheet KB.01 “Power-operated windows” issued by the VFF (window, door and facade manufacturers)

www.eurowindoor.eu/news-and-proceeding/

position-papers-and-publications/

ATTENTION

A restrictor stay with an adequate stroke must be installed in bottom hung wings.

It is important to ensure that the fastening of the actuator on the window or wing frame is designed to be permanent and suitable for the actuator force specified on the type plate.

46VWURNHPP / 56VWURNHPP / 66 VWURNHPP/ 76VWURNHPPVWURNHPP

183,7

Connection

EA-K-30/xxx-T & EA-K-30/xxx-T-DA

Gear side

Supply cable / USB-300

Optional connection Supply cable, only EA-K-30/xxx-T-DA

Chain side

234,3

468

VWURNHPP/

624

VWURNHPP/

727

VWURNHPP/

824

VWURNHPP

DIP switches &

LED display

Page 6

Figures

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 6

Figure 3: Top bracket K-K50-OK

Figure 4: Top bracket K-K-OK-SK

Figure 5: Inward opening bracket K-K30-AKI

Figure 6: Lower bracket K-K30-A

Figure 7: Lower bracket K-K30-K

Figure 8: Lower bracket – K-K30-FLEX

DEF

Page 7

EA-K-30 – Functions

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 7

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

4. EA-K-30 – Functions

4.1 Soft-close range

4.1.1 Speed reduction

The actuator has a factory-activated speed reduction function, the last 75 mm before reaching the “CLOSED” end position (see Table 1: “Electrical properties” on page 24 and Figure 10: “Configurable ranges” on page 8).

4.1.2 Current reduction

After reaching the last 75 mm before end position "CLOSED", the soft-close current becomes active, 0.3 A by default. This value can be increased to 1.0 A via SIMON LINK (when the speed reduction function is deactivated).

4.2 SIMON LINK

The actuator has a configuration interface (gear side) on which the following functions can be performed via SIMON LINK:

• The stroke can be electronically limited from 100 mm on.

• Forces can be set in the “OPEN” and “CLOSED” direction.

•The soft - close current can be adjusted.

• The speed reduction before the “CLOSED” end position for the soft - close range can be set (see Figure 10: “Configurable ranges” on page 8).

• The switching behaviour of the dry contact can be set.

• A detailed status message from the actuator and data logger can be read.

Figure 9: Configuration interface for SIMON LINK

ATTENTION

In order to avoid damage to the window and actuator or injuries to individuals, the cut-off current limit is automatically reduced to 0.3 A when the speed reduction function is activated; this corresponds to a force of approx. 150 N. The cut-off current limit can be increased to a maximum of 0.5 A (300 N) via SIMON LINK when the speed reduction function is activated.

INFORMATION

You need a service cable (USB-300) and the associated software (from version 2.0.0) for configuration of the actuator via SIMON LINK.

For more information visit

short.simon-protec.com/slen

ATTENTION

The cut-off of the actuator in the configuration is provided by the USB-300 cable.

There must be no external power supply at this point in time (EA-K-30/xxx-T-DA on the chain side).

gear side

connector for USB-300 cable

Page 8

EA230-K-30 – Functions

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 8

4.3 Configurable ranges

Soft-close range: moves with the electronic zero point, the soft-close current ISC and the speed reduction can be configured via SIMON LINK.

Reset range: the electronic zero point is reset when switching off via load in direction of the “CLOSED” driving direction within the

first 30 mm before the “CLOSED” end position.

Stroke: electronic stroke limitation depending on programming.

Figure 10: Configurable ranges

5. EA230-K-30 – Functions

5.1 End position cut-off while closing

The end position cut-off while closing occurs automatically (load depending) and is not programmable. The electronic switches off the actuator, when reaching a threshold value, if, for example, the window is completely closed and moved into the gaskets.  After the window is closed each time or the cut-off current has been exceeded, the chain is extended slightly again to protect the gaskets and the window.

5.2 End position cut-off while opening

The cut-off in the OPEN end position occurs automatically and can be set with the DIP switches 1-2.

A teach-in run must be performed after setting the DIP switches (three switch combinations for the STROKE setting).

5.3 DIP switches

(See Figure 2: “EA230-K-30/xxx(-S) chain actuator” on page 5.)

mechanical ]HUR

electronical ]HUR

mechanical “max”

30 mm

75 mm

reset range

soft-closerange

electronical stroke

50 mm

stopping time 3 s

50 mm

before max. electr. stroke

stopping time 0 s

ATTENTION

The actuator must be de-energised before the DIP switches can be changed. After setting the DIP switches, a pause of approx. 5 seconds must be observed before the drive can be supplied with power again.

DIP

switch 1

DIP

switch 2

Function

ON ON

Maximum stroke  (delivery condition)

OFF ON STROKE reduced by 100 mm

ON OFF STROKE reduced by 200 mm

OFF OFF

RESET  (See chapter 5.4 “RESET” on page 9)

Page 9

EA230-K-30 – Functions

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 9

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

5.4 RESET

 If necessary, release the connection between the chain

end piece and the top bracket.

 Drive the actuator in the OPEN direction and extend the

chain by approx. 10 cm.

 Disconnect the actuator from the power supply.

 Check the communication cables in the case of actuators

connected in parallel (red / white).

 Set both of the DIP switches 1 and 2 to OFF.

 Wait for five seconds.

 Drive the actuator in the OPEN direction.

The RESET procedure is performed, the orange LED

lights up continuously during this procedure. The actuator immediately moves in the CLOSED direction up to the end position, then approx. 5 cm back in OPEN direction.

The orange LED flashes continuously after performing

the RESET process correctly.

 Disconnect the actuator from the power supply again.

 Set the DIP switches 1 and 2 to the desired setting.

 Wait for five seconds.

 Connect the chain end piece to the top bracket again.

 Let the actuator perform a teach-in run 

(see chapter 5.6 “Performing a teach-in run” on page 9).

5.5 Teach-in run

The actuators detect and store the distance between sash and frame fully automatically during operation (when the window is fully closed). The dimensional difference between wing and frame is called overhang.

This teach-in takes place when the actuator fully closes the window for the first time after a RESET.

5.6 Performing a teach-in run

 Open the actuator slightly and then drive it in the

CLOSED direction and let it cut off in the end position.

If the teach-in process has worked correctly, the

actuator signals this by the flashing of the orange LED (next to the DIP switches) for approx. 3 seconds.

 If the orange LED does not flash as described, a RESET

must initially be performed

(see chapter 5.4 “RESET“).

ATTENTION

The chain end piece must not be connected to the bracket when performing the RESET process.

ATTENTION

The communication cables of the actuators must be connected to each other during the RESET process in synchronous mode (red with red and white with white).

ATTENTION

After RESET, e.g. after a stroke setting via the DIP switches or after installation, you must perform a teach-in run.

Page 10

EA230-K-30 – Functions

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 10

5.7 LED displays

The EA230-K-30 has three status LEDs (see Figure 2: “EA230-K-30/xxx(-S) chain actuator” on page 5) with the following meanings.

Red LED

Number

flashes

Type of error Possible solution

1 Overload cut-off

• Check the drives for correct installation  (mechanical / electrical);

• Is the force of the installed actuators adequate.

Communication error (Synchro)

• Perhaps there are actuators connected that do not have a common RESET.

• Check the red / white connection cable;

• Perform a RESET procedure for the interconnected actuators.

3 ——

Inconsistent DIP switch settings (Synchro)

• The DIP switch settings of the interconnected actuators do not match.

• Check and correct the DIP switch settings.

5 Error during the RESET procedure • Repeat the RESET procedure.

Cabling error (Synchro)

• The power input of the the interconnected actuators does not match.

• Check and correct the connection of the actuators.

Addressing error (Synchro)

• The assignment of the internal addresses of interconnected actuators has failed.

• Perform a RESET procedure.

Power supply error

• The supply voltage is not within the permissible range or is not stable.

• Check the electrical connection;

• Check the supply voltage.

Chain alignment error (Synchro)

• The chain position (STROKE) of the interconnected actuators is not within the permissible range

• Perform a RESET procedure.

Memory error (Synchro)

• The storage process in the internal memory was not successful.

• Repeat the RESET procedure.

Connection error

• A RESET procedure is performed at the same time in the case of several non-synchronous actuators.

• Perform the RESET procedures individually.

Green LED

LED status Meaning

Continuously

lighting

The voltage supply to the actuator is correct.

The actuator is closed correctly and the storage of the STROKES has been performed successfully.

Flashing

The voltage supply to the actuator is correct.

The set STROKE has been reached. The number of flashes indicates the internal address to which the actuator has been assigned during the RESET procedure in the case of synchronous actuators.

Page 11

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 11

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6. Mounting

See supplementary sheet “Safety Instructions and Warranty Conditions”!

6.1 Mechanical connection

— Mechanical connection

You need different combinations of brackets for mounting the actuator depending on the mounting position and the shape of the window or building cover; the brackets (see page 6), with the exception of the top bracket K-K50-OK, must be ordered separately.

 In order to ensure that the window is sealed securely,

check that the chain of the actuator is extended slightly before mounting the actuator. However, the chain should not extend more than 30 mm after mounting the actuator otherwise the electronic zero point reset can no longer be guaranteed

(see Figure 10: “Configurable ranges” on

page 8).

Orange LED

LED status Meaning

Continuously

lighting

duration < 0.5 sec.

Write process in the internal memory of the actuator is running.

Continuously

lighting

RESET procedure is running.

Continuously

lighting for 3 sec.

Teach-in procedure of the teach-in run has been completed correctly.

Flashing

RESET procedure completed correctly. The number of flashes indicates the internal address to which the actuator has been assigned during the RESET procedure in the case of synchronous actuators.

INFORMATION

Further information on mounting can be found in the guidance sheet KB.01 “Power-operated windows” issued by the VFF (window, door and facade manufacturers)

www.eurowindoor.eu/news-and-proceeding/

position-papers-and-publications/

DANGER

The system must be mounted by specialist personnel (qualified electricians) only. All relevant national safety regulations and directives apply to mounting, installation and commissioning.

Improper mounting can create a risk of electric shock. All safety regulations must be complied with. Follow the current assembly instructions. Incorrect mounting can lead to serious injury.

ATTENTION

Please note the static properties of the window frame when mounting the actuator.

Use suitable fixings depending on the window material on which the actuator is to be mounted. (The fixings are not included in the delivery!)

Page 12

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 12

6.1.1 Mounting brackets

 Determine the mounting position of the brackets so that the chain of the actuator will not collide with the (window / wing) frame

in any opening position of the window and the position of the chain is in the centre of the window; centre line markings are provided on the K-K-50-OK for this purpose

(see Figure 14 on page 13). In parallel / duo operation the actuators should be

positioned in such a way that the chains are located on 1/4 of the edges (left/right) of the window sash.

 Secure the brackets with screws that are suitable for the respective window or the desired surface (screws / fixings are not

included in the delivery), see Figures page 15 and page 16.

 Insert the actuator in the support brackets and secure it with the two self-locking screws.

Figure 11: K-K30-K Figure 12: K-K30-A

Figure 13: K-K30-FLEX

Page 13

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 13

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6.1.2 Top bracket K-K50-OK Figure 14

 Extend the chain approx. 10 cm and connect the chain end piece to the K-K50-OK (1). To do this, insert the fixing bolt from

the side with the logo (2) and secure it on the other side with the retaining ring (3).

Figure 15

Figure 16: Incorrect positioning of the K-K50-OK

ATTENTION

The top bracket must always be aligned in such a way that the SIMON logo on the bracket is on the same side of the chain as the SIMON logo on the chain exit.

INFORMATION

Centre line marking (see Figure 14) for aligning the bracket on the middle of the wing (single variant) or at a distance of 1/4 away from the edge (left / right) in parallel operation.

SIMON

logos

centre line marking

ATTENTION

The top bracket K-K50-OK must not be mounted turned, otherwise its function can no longer be fully guaranteed (see Figure 16: “Incorrect positioning of the K-K50-OK”).

INFORMATION

With the help of the alternative upper bracket K-K-OK-SK, turned mounting with lateral force flow is possible (see

6.1.4 “Top bracket K-K-OK-SK” on page 15).

So nicht!

Not in this way!

Page 14

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 14

6.1.3 Inward opening bracket K-K30-AKI

Figure 17

 Extend the chain approx. 10 cm and connect the chain end piece to the K-K30-AKI (1). To do this, insert the fixing bolt from

the side with the logo (2) and secure it on the other side with the retaining ring

(3).

Figure 18

ATTENTION

In the case of a compression force application (e.g. top hung window),the mounting bracket must always be aligned so that the SIMON logo of the bracket is on the same side as the SIMON logo of the chain outlet.

INFORMATION

Window heights in a ratio of approx. 2 : 1 to the actuator stroke (opening width) are possible for the inner hole pairs (for the fixing bolt) depending on the quality and shape of the window sash. This ratio changes to approx. 3 : 2 for the outer hole pair.

These are only approximate guideline values and must be clarified before any mounting in case of doubt!

SIMON logos

Page 15

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 15

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6.1.4 Top bracket K-K-OK-SK Figure 19

6.1.5 Inward opening top / bottom hung window, mounting on a blind frame

Figure 20: Inward opening bottom hung window

6.1.6 Outward opening top / bottom hung window, mounting on a blind frame

Figure 21: Outward opening top hung window

ATTENTION

The top bracket must always be aligned in such a way that the SIMON logo on the bracket is on the same side of the chain as the SIMON logo on the chain exit in the case of top hung wing applications.

Note the resulting alignment of the actuator (see Figure 19). The combination of actuator and bracket must only be used in this alignment to one another. Any other alignment will lead to the loss of the function of the bracket.

min.

min. 39.5 mm*

plus pivoting range depending on the wing height

min. 70.5 mm*

min.

61.8 mm

16.8

Page 16

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 16

6.1.7 Inward opening top / bottom hung window, actuator mounted on the window sas h Figure 22: Inward opening bottom hung windo w, at the window sash

6.1.8 Inward opening bottom hung window, actuator K-K30 - F LEX mo unted on the window sash Figure 23

min.

ATTENTION

Position the actuator so that the chain is as far as possible away from the window sash in order to avoid damage to the window and the chain while opening it.

6min. mm

Page 17

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 17

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6.1.9 Rotary window

Figure 24: Mounted on a blind frame

Figure 25: Mounted on the window sash

ATTENTION

The chain actuator EA-K-30 / EA230-K-30 must only be mounted upright (with the actuator side at the top) on DIN right windows!

Page 18

Mounting — Mechanical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 18

Figure 26: K-K30-FLEX mounted on the window sash 6.1.10 Calculating forces/stroke

This calculation is only valid for wall windows mounted vertically. A detailed calculation must be made for all other mounting positions, which we will be pleased to assist you with.

F := the force of the actuator [N] S := the stroke of the actuator [mm] H := the height of the window sash [mm] W := the weight of the window sash [kg]

Required actuator force for the specified stroke:

F = (W / 2) x (S / H) x 10

= (W x S x 5) / H

Maximum possible actuator stroke for the specified force:

S = (2 x F x H) / (W x 10)

= (F x H) / (W x 5)

Figure 27

6.1.11 Permissible pushing force on the chain Figure 28

height of the frame – H

weight of the

frame – W

force F

stroke S

bottom hung window

height of the frame – H

weight of the

frame – W

force F

stroke S

top hung window

250

200

150

100

force[N]

500 600

750

1000

stroke [mm]

700 800700 900

static push force

dynamic push force (eg. wind load)

650 850 950

300

550

400

450

1100

1050

1200

1150

pull force

Page 19

Mounting — EA-K-30 Electrical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 19

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6.2 EA-K-30 Electrical connection

— EA-K-30 Electrical connection

6.2.1 Supply

The power supply must be designed for the actuator. The vol

tage and current must correspond with the information on the type plate. The supply cabling must be checked before the initial commissioning, the cable cross section in particular must be taken into account. The valid regulations regarding minimum values for the cable sizing must be observed! Sample calculation (this is only an approximate value and does not replace an exact calculation):

The power is supplied to the EA-K-30/xxx-T on the gear side.

The power can also be supplied via the chain side on the EA-K-30/xxx-T-DA (double-sided connection). The supply voltage is relayed internally to the opposite connection point, this can then be used to connect another actuator (see chapter 6.2.8 “DUO operation / parallel connection” on page 21).

6.2.2 Supply / connection cable

It is possible to supply power to the second actuator directly thro

ugh the first actuator (DA variant) in tandem / duo operation. The supply cable can therefore be changed into a connection cable.

 Cut the second supply cable to the desired length (plus

app

rox. 3 cm).

 Strip the cable over a length of 18 mm and remove 4 mm

of insulation from the 5 cores.

 Screw the 5 cores into the connector and secure the

cable with a cable binder (e.g. 100 x 2.5) as traction relie

black

yellow

red

blue

brown

ATTENTION

Make sure that the loops of the supply cable are adequately sized on moving parts, taking account of the bending radii, in order to prevent the pinching or tearing of the supply cable.

DANGER

Connect to the power supply (24 V DC) only after checking the entire system.

INFORMATION

We recommend performing a trial run with a suitable mobile power supply (incl. a control device, not just a battery). This means that it is quick and easy to respond to malfunctions.

ATTENTION

Do not earth the electrical connection. The actuator must only be operated with a 24 V DC safety

extra-low voltage. Unused cores must be insulated.

INFORMATION

Size information for actuator cable (empirical formula):

Cable cross section [mm²] = single cable length [m] 

x number of actuators x current consumption  per actuator [A] / 73.

The DIN VDE 0100 and DIN VDE 0298 regulations continue to apply.

Page 20

Mounting — EA-K-30 Electrical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 20

 Place the green connector and the cable binder in the

upper shell of the connector housing and screw the top shell to the bottom shell.

6.2.3 Feedback signal – “F” contact

It is possible to create a classic “F” contact

via the dry contact by connecting the yellow core (NO2) to the blue (S) core (see chapter 6.2.7 “Single connection – “F” contact” on page 20). The alarm triggering of the contact must therefore be activated in the “OPEN” and “CLOSED” end position via SIMON LINK.

6.2.4 Feedback signal – dry contact

The normally open contact (NO1, NO2) is activated in the CLOSED driving direction when the actuator is cut off in the “CLOSED” end position, the message is stroke-dependent and can be evaluated as a “CLOSED message”.  Other switching settings, such as in “OPEN” end position, can be set via SIMON LINK.

6.2.5 Feedback signal – tandem port

6.2.6 Single connection – dry contact

 Connect the cables according to the connection plan.

6.2.7 Single connection – “F” contact

 Connect the cables according to the connection plan.

INFORMATION

The output of the dry contact occurs only on the gear side of the actuator (see Figure 9: “Configuration interface for SIMON LINK” on page 7).

ATTENTION

Only a cut-off signal (e.g. overload cut-off) is switched over to the actuator connected in parallel. Monitoring of the cables or function of the actuators connected in parallel does not take place and therefore also does not lead to the cut-off of the actuators connected in parallel.

ATTENTION

When not in use, the red wire (T) must be electrically insulated. The red core must only be connected to the red core of an actuator connected in parallel.

ATTENTION

When not in use, the red wire (T) must be electrically insulated. The red core must only be connected to the red core of an actuator connected in parallel.

The “F” contact (black) must not be earthed or clamped in parallel!

volt-free contact

(max. 28 V / 1.0 A)

24V DC

NO1

OPEN: S = +

O = -

CLOSE: umpolen

actuator

NO2 O

tandem-port (electr. insulate)

blue

brown

black

yellow

red

“F”-contact

(max. 1.0 A)

24V DC

blue

NO1

OPEN: S = +

O = -

CLOSE: pole change

actuator

brown

NO2 O

black

yellow

red

tandem-port (electr. insulate)

Page 21

Mounting — EA-K-30 Electrical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 21

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6.2.8 DUO operation / parallel connection

A maximum of 2 actuators can be operated in parallel in DUO operation (via a connection cable) with the associated tandem. A maximum of 4 actuators can be operated in parallel with the associated tandem (e.g. on large wings).

If an actuator stops due to overloading, the actuator connected in parallel is also stopped after a predetermined run-on time (see Table 1: “Electrical properties” on page 24 and Figure 10: “Configurable ranges” on page 8).

 DUO operation: Connect the cables according to the connection plan.

blue

NO1

1. actuator (DA)

brown

NO2

black

yellow

red

blue

NO1

2. actuator

brown

NO2

red

O ST

blue

brown

red

connected

internally

connection cable

black

yellow

black

yellow

24V DC

OPEN: S = +

O = -

CLOSE: pole change

volt-free contact

(max. 28 V / 1.0 A)

tandem-port (electr. insulate)

EA-K-30/xxx-T

EA-K-30/xxx-T-DA

 Parallel connection: Connect the cables according to the connection plan.

24V DC

NO1

OPEN: S = +

O = -

CLOSE: pole change

1. actuator

NO2

volt-free contact

(max. 28 V / 1.0 A)

NO1

2. actuator

NO2

volt-free contact

(max. 28 V / 1.0 A)

blue

brown

black

yellow

red

blue

brown

black

yellow

red

up to

4 actuators

at all

ATTENTION

The actuators run at the same time, the power supply and the cable dimensions must be adapted to the total current of the system.

ATTENTION

Only connect 2 actuators to each other. Maximum cable length of 10 m between the actuators.

ATTENTION

Only connect 4 actuators in parallel to each other. Maximum cable length of 10 m between two actuators.

Page 22

Mounting — EA230-K-30 Electrical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 22

6.3 EA230-K-30 Electrical connection

— EA230-K-30 Electrical connection

6.4 Single connection – standard variante (

EA230-K-30 / xxx)

 Connect the cables according to the connection plan.

230 V AC

blue

OPEN

black

factory

provided

actuator

brown

DANGER

Please note

• The VDE 0833 standard for hazard alert systems,

• The VDE 100 standard for electrical systems,

• The local fire department regulations,

• The energy supply company regulations for the mains connection,

• And the DGUV V3 / V3DA / V4 regulations and the workplace regulation ASR A 1.6.

All the relevant national safety regulations and directives apply when installing, commissioning and putting the actuator into operation outside the country of manufacture (Germany).

DANGER

It is important to observe the five safety rules in accordance with EN 50110-1 or DIN VDE 0105-100.

1. Disconnect completely!

2. Secure against reconnection!

3. Verify that the installation is dead!

4. Carry out earthing and short circuiting!

5. Provide protection from adjacent live parts!

ATTENTION

Make sure that the loops of the supply cable are adequately sized on moving parts, taking account of the bending radii, in order to prevent the pinching or tearing of the supply cable.

ATTENTION

Never supply 230 V AC to LA (OPEN) and LZ (CLOSE) at the same time and observe the prescribed pause time of 300 ms for the switchover. Any infringement will lead to the destruction of the actuator.

Page 23

Mounting — EA230-K-30 Electrical connection

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 23

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

6.4.1 Parallel connection (EA230-K-30 / xxx)

 Connect the cables according to the connection plan.

230 V AC

1. actuator

8. actuator

OPEN

LZL

brown

blue

black

max. 8 actuators in parallel behind a switching element

brown

black

blue

factory

provided

6.4.2 Synchronous connection (EA230-K-30 / xxx-S)

 Connect the cables according to the connection plan.

230 V AC

1. actuator

2. actuator

OPEN

LZL

C1 C2

LZL

C1 C2

blue

brown

red

white

black

max. 8 actuators in parallel behind a switching element

factory

provided

blue

brown

red

white

black

ATTENTION

Connect a maximum of 8 actuators in parallel to a switching element.

ATTENTION

Connect a maximum of 8 actuators in parallel to a switching element.

Page 24

EA-K-30 – Technical Data

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 24

7. EA-K-30 – Technical Data

Table 1: Electrical properties

Actuator type/version EA-K-30

Rated voltage

Permissible rated voltage range

Ripple of the rated voltage Vpp

Undervoltage detection

Nominal current

1. Maximum current consumption at nominal load

Maximum starting current in “OPEN” and “CLOSED” direction

Maximum cut-off current in “

OPEN” and “CLOSED”

direction, after start-up

2. Can be configured via SIMON LINK.

soft - close current

3. Soft - close range: last 75 mm before reaching the “CLOSED” end position, soft - close current can be configured via SIMON LINK – current rang

e: 0.3 A – 1,0 A; when the speed reduction function is activated

0.3 A – 0.5 A.

Current consumption after cutoff (closed current)

Cut-off via

Maximum permissible number of

actuator units connected in

parallel in tandem operation

4. With a common cut-off function (tandem function).

Cable length between two actuators in tandem operation

Tandem run-on time

5. The tandem run-on time indicates how long the actuator connected in parallel continues to run after cutting off the triggering actuator. The run-on time is 3 s in each case 50 mm before reaching the end posit

ion and 0 s in the range between (see Figure 10: “Configurable

ranges” on page 8).

Pulse time

6. The pulse time indicates how long the internal or external overload cutoff provides the cut-off signal at the output.

Protection class

Table 2: Dry contact (NO1, NO2)

Actuator type/version EA-K-30

Rated voltage

Contact load relay

The normally open contact (NO) is only activated in the “CLOSED” end position when the actuator is cut off. This means that the message is stroke-dependent and can be evaluated as a “CLOSED message”. Activation of the actuator at the “OPEN” end position can also be configured via SIMON LINK, as well as other settings.

Table 3: Connection and operation

Actuator type/version EA-K-30

Silicone connection cable with connector

Supply cable length

1. Optional lengths possible.

Pause time at a change in the

driving direction

2. It is necessary that the supply voltage ensures a pause time (zero volt range) of at least 500 ms for a change in the driving direction (pole re

versal) (see Figure 29: “Zero volt range at a change in the driving

direction” on page 25).

Switch-on duration S2 ED 30% (short-time duty

Stability of opening and closing c

ycles

Sound level

3. Measured at a distance of one metre under normal conditions.

Re-triggering in accordance with prEN 12101-9

Re-triggering after a stop

Maintenance

24 V DC

24 V DC -15%; +15%

max. 500 mV

yes

1.0 A

1.1 A

0.3 A

40 mA

Integrated electronic overload

cut-

off

2 in DUO operation

4 in p

arallel operation

(see chapter 6.2 “EA-K-30

Electrical connection” on

page 19)

max. 10 m

3 s

300 ms

III

max. 28 V DC

1.0 A

ATTENTION

The maximum load capacity of the contact must not be exceeded (see Table 2: “Dry contact (NO1, NO2)”).

INFORMATION

The output of the dry contact occurs only on the gear side of the actuator (see Figure 1: “EA-K-30/xxx-T(-DA) chain actuator” on page 5)!

5 x 0.75 mm²

3 m

at least 500 ms

3 of 10 minutes)

000

≤ 55 dB (A)

permitted

See chapter 11.1 “Care and

Main

tenance” on page 28.

Page 25

EA-K-30 – Technical Data

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 25

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

Figure 29: Zero volt range at a change in the driving

direction

Table 4: Installation and ambient conditions

Actuator type/version EA-K-30

Nominal operating temperature

Permissible ambient temper

ature range

Temperature stability (smoke and heat

exhaustion)

Protection rating

Area of application

Table 5: Approvals and certificates

Actuator type/version EA-K-30

CE-compliant

Further approvals

Table 6: Mechanical properties

Actuator type/version EA-K-30

Nominal pushing force

1. Only under optimum conditions, up to a 600 mm stroke (see chapter 6.1.11 “Permissible pushing force on the chain” on page 18), pushing force can be configured via SIMON LINK.

Nominal pulling force

2. Pulling force can be configured via SIMON LINK.

Conditions of loading

Nominal locking force

3. The force may vary depending on the design of the actuator, bracket, fixing type, window material etc.

Nominal stroke

4. In the case of a stretched chain, e.g. traction relief. The nominal stroke may deviate by ± 3%, but no more than 20 mm, due to mechanical damping.

 – EA-K-30 / 400-T(-DA) – EA-K-30 / 600-T(-DA) – EA-K-30 / 800-T(-DA) – EA-K-30 / 1000-T(-DA) – EA-K-30 / 1200-T(-DA)

Stroke speed

5. Based on a 600 mm stroke; deviation ± 5%.

 – 300 N – 200 N – 100 N

Material – surface

Material – chain

Dimensions (W x H

7. Plus chain exit (7 mm).

x D)  – EA-K-30 / 400-T(-DA) – EA-K-30 / 600-T(-DA) – EA-K-30 / 800-T(-DA) – EA-K-30 / 1000-T(-DA) – EA-K-30 / 1200-T(-DA)

Weight

8. Information without supply cable and brackets.

 – EA-K-30 / 400-T(-DA) – EA-K-30 / 600-T(-DA) – EA-K-30 / 800-T(-DA) – EA-K-30 / 1000-T(-DA) – EA-K-30 / 1200-T(-DA)

Table 7: Accessories

Actuator type/version EA-K-30

Mechanical connection to the actuator medium (chain)

Mechanical connection to the actuator

housing

ATTENTION

Voltage stability/quality: only defined cut-off processes are permitted (cut-off time of 24 V DC rated voltage to 0 volts in t < 10 ms).

This also applies in particular to switching processes from a primary (mains operation) to secondary energy source (backup batteries).

20 °C

from 0 to 75 °C

300 °C

IP 32

Central European

envir

onmental conditions

 2000 metres obove sealevel

In accordance with the EMC

Dir

ective 2014 / 30 / EU and the

Low Voltage Directive

2014 / 35 / EU

on request

300 N

S: +24 V O: GND

O: +24 V S: GND

0 V

[V] (DC)

[ms]

D 500 ms

“OPEN”

“CLOSE”

Opening against the nominal

load /closing with nominal load

support

≤ 2000 N

400 mm 600 mm 800 mm

000 mm

200 mm

9.7 mm / s

11.1 mm / s

12.5 mm / s

Aluminium E6 / EV1

Coatings

are possible in all

RAL and DB colours

Corrosion-resistant,

nostable steel chain, silver

nickel-plated

(a high-grade steel chain is

optionally available)

467 x 37 x 35 mm 564 x 37 x 35 mm 667 x 37 x 35 mm 764 x 37 x 35 mm 867 x 37 x 35 mm

1.30 kg

1.52 kg

1.80 kg

2.02 kg

2.30 kg

6. Attention: Screws, nuts, discs, sliders and similar individual components are not coated.

A wide selection of bracket sets

is available. The technical data only applies in connection with

original accessories!

Actuator type/version EA-K-30

Page 26

EA230-K-30 – Technical Data

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2 / 01.2019

Page 26

8. EA230-K-30 – Technical Data

Table 8: Electrical properties

Actuator type/version EA230-K-30

Rated voltage

Permissible rated voltage range

Undervoltage detection

Nominal current

1. Maximum current consumption at nominal load

Maximum starting current in “OPEN” and “CLOSED” direction

Maximum cut-off current in “

OPEN” and “CLOSED”

direction, after start-up

Current consumption after cutof

f (closed current)

Cut-off via

Maximum permissible number of

actuators connected in

parallel

Cable length between two actuator

s in synchronous

operation

Protection class II

Table 9: Connection and operation

Actuator type/version EA230-K-30

Plastic connection cable

Supply cable length

Pause time at a change in the dr

iving direction

Switch-on duration

Stability of opening and closing cyc

les

Sound level

1. Measured at a distance of one metre under normal conditions.

Maintenance See chapter 11.1 “Care and

Maintenance” on page 28.

Table 10: Installation and ambient conditions

Actuator type/version EA230-K-30

Nominal operating temperature

Permissible ambient tempera

ture range

Protection rating

Area of application

Table 11: Approvals and certificates

Actuator type/version EA230-K-30

CE-compliant

Further approvals

Table 12: Mechanical properties

230 V AC

-10 %; +10 %

0.23 A

0.25 A

10 mA

Integrated electronic overload

cut-

off

max. 10 m

3 x 0.5 mm²

5 x 0.5 mm²

(synchronous)

2 m

2.5

m (synchronous)

at least 300 ms

ED 30% (short-time duty

3 of 10 minutes)

000

≤ 55 dB (A)

20 °C

from 0 to 75 °C

IP 32

Central European

envir

onmental conditions

 2000 metres obove sealevel

In accordance with the EMC

Dir

ective 2014 / 30 / EU and the

Low Voltage Directive

2014 / 35 / EU

on request

Actuator type/version EA230-K-30

Nominal pushing force

300 N

Nominal pulling force 300 N

Conditions of loading Opening against the

nominal loa

d /

closing with nominal load

support

Nominal locking force

≤ 2000 N

Nominal stroke

 – EA230-K-30 / 300(-S) – EA230-K-30 / 600(-S) – EA230-K-30 / 800(-S) – EA230-K-30 / 1000(-S)

300 mm 60

0 mm

800 mm

000 mm

Stroke speed

 – 300 N – 200 N – 100 N

9.7 mm/s

10.0 mm/s

10.3 mm/s

Material – surface Aluminium E6 / EV1

Coa

tings

are possible in all

RAL and DB colours

Material – chain Corrosion-resistant,

monost

able steel chain, silver

nickel-plated

(a high-grade steel chain is

optionally available)

Page 27

Commissioning

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator – EA230-K-30/xxx(-S)

Page 27

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

Issue: 1.2 / 01.2019

info@simon-protec.com

Table 13: Accessories

Actuator type/version EA230-K-30

Mechanical connection to the actuator medium (chain)

A wide selection of bracket sets is available. The technical data only applies in connection with original accessories!

Mechanical connection to the actuator

housing

9. Commissioning

See supplementary sheet "Safety Instructions and Warranty  Conditions"!

9.1 EA230-K-30

Perform a RESET procedure (see chapter 5.4 “RESET” on page 9) and a teach-in run (see chapter 5.5 “Teach-in run” on page 9) after mounting the actuators.

10. Troubleshooting

10.1 EA-K-30

10.2 EA230-K-30

See chapter 5.7 “LED displays” on page 10.

Dimensions (W x H6 x D) 

– EA230-K-30/300(-S) – EA230-K-30 / 600(-S) – EA230-K-30 / 800(-S) – EA230-K-30 / 1000(-S)

468 x 37 x 35 mm 624 x

37 x 35 mm 727 x 37 x 35 mm 824 x 37 x 35 mm

Weight

 – EA230-K-30 / 300(-S) – EA230-K-30 / 600(-S) – EA230-K-30 / 800(-S) – EA230-K-30 / 1000(-S)

0.90 kg

1.40 kg

1.80 kg

2.20 kg

1. Only under optimum conditions, up to a 600 mm stroke (see chapter 6.1.11 “Permissible pushing force on the chain” on page 18).

2. The force may vary depending on the design of the actuator, bracket, f

ixing type, window material etc.

3. In the case of a stretched chain, e.g. traction relief. The nominal stroke may deviat

e by ± 3%, but no more than 20 mm, due to mechanical

damping.

4. Based on a 600 mm stroke; deviation ± 5%.

5. Attention: Screws, nuts, discs, sliders and similar individual components are not coated.

6. Plus chain exit (7 mm).

7. Information without supply cable and brackets.

Actuator type/version EA230-K-30

Malfunction Possible causes Troubleshooting

The actuator is not working. – Mains power supply is missing;

– Supply cable is faulty;

– Wind/rain sensor has triggered.

– Check the fuse and the supply cable;

– Check the supply cable;

– No failure

The actuator has the wrong running direction.

– Terminals “+ / -” 

are mixed up; S = blue; O = brown.

– Change the polarity of terminals “S” and “O”.

The actuator continues to run beyond its programmed stroke.

– Displacement of the electronic zero

point.

– Drive the actuator in the “CLOSED” direction and let it

cut off in the “CLOSED” end position.

Page 28

Annex

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

– EA230-K-30/xxx(-S)

BA_EA(230)-K-30-XXX_EN_12 www.simon-protec.com Date: 13.02.2019

info@simon-protec.com Issue: 1.2/ 01.2019

Page 28

Operating ManualBA_EA(230)-K-30-XXX_EN_12

11 Annex

11.1 Care and Maintenance

See supplementary sheet "Safety Instructions and Warranty Conditions"!

short.simon-protec.com/sugen

11.2 General business and delivery terms

Deliveries and services are subject to the currently applicable terms for products and services of the electrical industry (green delivery terms), including the supplementary clause “Extended retention of title”. These are published by the German Electrical and Electronic Manufacturers' Association (ZVEI), Frankfurt. If you are not aware of these, we will gladly send them to you. You can also download these agreements from

short.simon-protec.com/agben

The place of jurisdiction is Passau.

11.3 Company Addresses

11.3.1 System manufacturer

SIMON PROtec Systems GmbH Medienstraße 8 94036 Passau Tel.: +49 (0) 851 988 70 - 0 Fax: +49 (0) 851 988 70 - 70 E-Mail: info@simon-protec.com Internet: www.simon-protec.com

11.3.2 Germany

SIMON PROtec Deutschland GmbH Medienstraße 8 94036 Passau Tel.: +49 (0) 851 379 368 - 0 Fax: +49 (0) 851 379 368 - 70

SIMON PROtec Deutschland GmbH Ammerseestraße 75 D – 82061 Neuried Tel.: +49 (0) 89 79 17 0 - 11 Fax: +49 (0) 89 79 17 9 - 72

E-Mail: info@simon-protec.de Internet: www.simon-protec.de

11.3.3 Switzerland

SIMON PROtec Systems AG Allmendstrasse 38 8320 Fehraltorf Tel.: +41 (0) 44 956 50 30 Fax: +41 (0) 44 956 50 40 E-Mail: info@simon-protec.ch Internet: www.simon-protec.ch

11.3.4 Hungary

SIMON PROtec Systems Kft. Sodras utca 1. fszt. 1 1026 Budapest Tel.: +36 (0) 30 552 0424 E-Mail: info@simon-protec.hu Internet: www.simon-protec.hu

12 Manufacturer's declaration

We hereby declare that the product complies with the applicable directives. The declaration of conformity can be read at the company's premises and will be sent to you upon request. This declaration certifies that the product complies with the mentioned directives, but does not represent any guarantee of the product's features. This declaration loses

its validity, if the product is modified without seeking our prior authorisation.

13 EC manufacturer’s declaration (distributor)

The installer is responsible for the proper mounting or commissioning, the preparation of the declaration of conformity in accordance with the EU directives and for affixing the CE marking. The CE marking must be affixed visibly!