Simon Simon, Basic ITI 60-776-02-95R Installation Instructions Manual

Download

Page 1

Installation Instructions

Simon® Basic : 2

Simon

Security System

Document No. 466-1574

Rev F Dated February 2003

Table of Contents

Programming Overview 26

Special Installation Requirements 3

Requirements for UL-Listed Installations 3 Canada Listings (pending) 3 California State Fire Marshall Listing 3 Introduction 4 System Components 4 Planning Sensor Types & Locations 7 Planning Control Locations 10 Planning for Lamp*, Appliance*,

Wallswitch*, and Universal/Garage Door* Module Control 10

Setting the House Code and Unit Number 10

Planning System Access Codes 12

Utility Access Code 1 12 Utility Access Code 2 12 Master Access Code 12 Access Codes (1 - 5) 12 Panic Code 12

Planning System Options 12

Reset Memory to the Factory Defaults 20

Wiring the Control Panel 23

Connecting Hardwire Interior Sirens 23 Connecting a Hardwire Exterior Siren 23 Connecting Hardwire Sensors 23 Connecting the Universal/Garage Door

Opener Module* 24 Connecting the Power Transformer 24 Connecting the Backup Batteries 24

Installing a Non-rechargeable Battery 24

Installing a Rechargeable Battery 25

Connecting the Phone Line to the Control

Panel 25

Installing an RJ-31X Jack 25

Connecting the Phone Line to the Control

Panel 25

Programming Sensors 27

Programming the House Code and Unit

Numbers* 28

Programming Light and Appliance Con-

trols* 28 Programming Options 29 Programming System Access Codes 30

Installing the System 31

Control Panel General Information 31

Control Panel Specifications 31

Installation Guidelines 31

Sensor Installation 32

Testing the Control Panel 32

Testing the System 32

Testing Sensors 33

Sensor Tripping Instructions: 33

If a Sensor Fails the Sensor Test 34

Testing Phone Communication 34 Testing Central Station Communication 34 Testing the X-10 Lamp Modules* 35 Siren and X-10 Lamp Module Functions*

35 Panel Tamper 35 Troubleshooting 36 Typical Backup Battery Life of th e 9 Volt Ul-

traLife 38

Notices 39 Index 41 Quick Reference Guide (Bac k Page )

Attachment: 466-1622, Booklet of Installation Instructions for SAW Sensors

Page 2

Simon® Basic :

Features not Available with the Simon® Basic ITI # 60-776-02-95R

2-Way Voice Remote Phone Control Speaker Volume Control Chime Special Motion Light Control Wireless Sire ns

Options not for Use with Simon® Basic

Modules that Cannot be Used with Simon® Basic

Interrogator 200 Audio Verification Module® (AVM) (60-787)

X-10 Lamp (13-403) Appliance (13-402) Powerhorn/Remote (13-398) Universal/Garage Door (13-399) Wall Switch Modules (13-397) Touchtalk 2-Way RF Touchpad (60-788-95R) Supervised Wireless Siren SWS (60-736-95)

Option 33: 2-Way Voice Option 36: Sensor Activated Light Lockout Start

Time Option 37: Sensor Activated Light Lockout Stop

Time Option 42: Speaker Level Option 46: Fire Shutdown - AVM Option 47: AVM Mode Option 48: Panic Talk

)

*(,QWHUORJL[

*(,QWH UORJ L[+RP H OLQN,QW H UURJDWRU6LPRQDQG7RROER[DUHUHJLVWHUHG WUDGHPDUNVRI*(,QWHUORJL[$OORWKHUWUDGHPDUNVDUHSURSHUWLHVRIWKHLURZQHUV

$OOULJKWVUHVHUYHG

6HFRQG6WUHHW1RUWK 1RUWK6DLQW3DXO01 7HFKQLFDO6XSSRUW

Page 3

Installat i on Instructions Document No. 466- 1574

Special Installation Requirements

This security system can be used as a fire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three.

Some installati ons may requir e certain c onfigurations dictated by city codes, state codes, or insurance requirements . The following information indicates the components of various listings.

Requirements for UL-Listed Installations

This section describes the minimum system configurations for UL-listed, Grade A (super vised) systems.

Typical System

All UL-listed systems req uire the follo wing basic components. The basic system does not require sensors and can use t he Remote Handhe ld Touchpad a s a controlling device.

• Basic Control Panel (60-776-02-95R)

• Control Panel (60-776-95R)

• Control Panel On-Board 2-Way Voice (60-77601-95R)*

• Class II Line Carrier Power Transformer (22-

091)*

• 9-Volt, 1.2 Ah Lithium Backup Battery (34-037) or a rechargeable 7.2Volt, 1 Ah Nickel Metal Hydride Battery Pack (34-052)

• Hardwire Siren (13-046) or LD105 Siren (13-

374)

Residential Fire Alarm System Unit (UL 985)

Basic system above, plus:

• System Sensor Smoke Sensor (60-506-95)

Canada Listings (pending)

Residential Burglary Alarm System Unit (ULC-S309)

Basic system as described for UL-listed installations, plus:

• Door/Window Sensor (60-670-95R)

Note: The KeyChain Touchpad #60-659 is UL Listed as a miscellaneous signalling device and is for supplementary use only.

CSA Certified Accessories Residential Fire Warning System Control Unit

(ULC-S545-M89)

Basic system as described for UL-listed installations, plus:

• Wireless Smoke Sensor (60-506-95)

• SUPSYNC (Supervisory Synchroniza ti on) set to 2 (hours)

California State Fire Marshall Listing

The California Stat e Fire Marshall li sting is approve d.

Residential Burglary Alarm System Unit (UL

1023)

Basic system above, plus:

• Door/Window Sensor (60-670-95R) suitable for installation on non-ferrous surfaces only

* = Not Available with Basic Model

Page 4

Installation Instructions Document No. 466-1574.

Introduction

This ITI Security System is easy to instal l if you plan ahead and perform the i nstallation in t he following order.

1. Plan where to locate the hardwire sirens, sensors and Control Panel. Use the tear out planning sheets at back of this manual.

2. Wire the Class I I transforme r, hardwire sirens, and phone.

3. Decide how the sensors, lights, and system options will operate.

4. Program the sensors, lights and appliances, and system options.

5. Install sensors and Lighting Modules.

6. Test system.

Note: Program the sensors before i nstalling t hem because the Control Panel and sensors must be in the same place for programming. After you’ve programmed each sensor, you can install them where you planned.

System Components

• X-10 Powerhorn/Remote Siren Modules (13-

398)*

• X-10 Universal/Garage Door Modu le s (13- 399) *

• X-10 Wall Switch Modules (13-397)*

Note: Use of the above X-10 modules has not been investigated by UL.

Figure 1. shows the Control Panel, co ntrol touchpads , and some compatible sensors and modules.

MOTION SENSOR

LAMP

MODULE

APPLIANCE

MODULE

SMOKE

SENSOR

SYSTEM STATUS

ARM

Doors &

Windows

ARM

Motion

Sensors

DISARM

526

Off

EMERGENCY

d&sres Hol hBtoeKy

REMOTE HANDHELD TOUCHPAD

CA R B O N M O NO X ID E

D E T E C T O R

CARBON MONOXIDE

ALARM

8988G21D.DSF

KEYCHAIN

TOUCHPAD

TOUCHTALK

2-WAY RF

TOUCHPAD

AUDIO VERIFICATION MODULE

DOOR/WINDOW

SENSOR

CONTINUOUS

MOMENTARY

GARAGE DOOR

MODULE

UNIT CODE

X-10 POWERHOUSE

OFF

HOUSE CODE

SOUNDER ONLY

SOUNDER & RELAY

RELAY ONLY

The system can monitor up to 24 sensors using any combination of the following sensors:

• Door/Window Sensor (60-670-95R)

• KeyChain Touchpad (60-659-95R)

• Remote Handheld Touchpad (60-671-95R)

• Touchtalk 2-Way RF Touchpad (60-788-95R)*

• Indoor Motion Sensor (60-639-95R)

• Outdoor Motion Sensor (60-639-95R-OD)

• Carbon Monoxide Alarm (60-652-95)

• Water Sensor (60-744-95R)

• Freeze Sensor (60-742-95R)

• SWS (60-736-95)*

• ITI 319.5 Sensors (including Smoke Sensors, excluding other touchpads)

Note: Both ITI SAW and Crystal sensors function with this Control Panel.

You may use any of these modules:

• Interrogator 200 Audio Verification Module (AVM) (60-787)*

• X-10 Lamp Modules (13-403)*

• X-10 Appliance Modules (13-402)*

Figure 1. Typical Security System Components

Security System

The security system has three types of components : the Control Panel, devices that report to the Control Panel, and devices that respond to commands from the Control Panel.

Control Panel

The Control Panel is the main processing unit for all security functions. It receives signals from and responds to wireless sensors and wireless touchpads throughout the premises. The buttons operate the security system. When us ing the Control Panel with the cover open, the buttons program the security system.

Two configurations of the Simon Control Panel are available. One has an on-board 2-way voice microphone, the other does not. The Interrogator can be added to either configuration.

* = Not Available with Basic Model

Page 5

Installat i on Instructions Document No. 466- 1574

Door/Window Sensor

For intrusion protection, install Door/Window sensors on all ground-floor door s and windows. At a minimum, install them in the following locations:

• All easily acces sible exter ior d oors a nd windows .

• Interior doors leading into the garage.

• Doors to areas containing valu abl es such as cabinets and closets.

KeyChain Touchpad

The KeyChain Touchpad enables you to turn the system on and off from right outsi de the home or to turn on the siren and to cal l t he c entral monitoring stat ion if there is an emergency. I f you hav e Lamp Modules , you can use the KeyChain Touchpad to turn all system controlled lights on and off.

Remote Handheld Touchpad

The Remote Handheld Touchpad enables you to tur n the system on and off while in the home, turn lights controlled by the system on and off (all or individual lights), or turn on a system siren and call the central monitoring station if t her e i s a no n-medical emergency. The Remote Handheld Touchpad will report an alarm type specific to its sensor type (see Table 3 on page 7 for sensor and siren types).

family rooms, and hal lways are candi dates for In door Motion Sensors. Indoor Motion Sensors are not suitable for rooms where pets can enter. Indoor motion sensors can also be used to sound chimes, but cannot be used for intr usion prote ction and a s a chime se nsor simultaneously.

Outdoor Motion Sensor

Use Outdoo r Motion Sensors to identify motion in a protected outdoor area. Detected motion in this protected area can sound chimes or turn o n outside lights. Do not use Outdoor Motion Sensors for i ntrusion protection.

Smoke Sensor

Smoke Sensors can provide fire alert protection by causing the alarm to sou nd throughout the hous e. You can add smoke sensors near sleeping areas and other floors of the house. Avoid areas which could have some smoke or exhaust such as att ics, kitchens, above fireplaces, dusty locations, garages, and areas with temperature extremes . In these areas yo u may want to install Rate-of-Rise sensors to detect extreme temperature changes. See the inst ructions packaged with the Smoke Sensor for comp lete placement information.

Refer to the diagram on the next page for specific placement of Smoke Sensors.

Touchtalk 2-Way RF Touchpad*

The wall-mounted wireless Touchtalk 2-Way RF Touchpad enables you to arm and disarm the system while in the home, turn s ystem controlled lights o n and off (all or individual lights), turn on a system siren, or call the central monitoring station if there is a non-medical emergency. The Touchtalk 2-Way RF Touchpad will report an alar m type s pecific t o its s ensor type (see Table 3 on page 7 for sensor and siren types). It annunciates status beeps and Control Panel voice feedback.

Note: Use of the Touchtalk 2-Way RF Touchpad has not been investigated by UL.

Indoor Motion Sensor

Indoor Motion Sensors are ideal whenever it is not practical to install Door/Window sensors on every opening. Identify areas where an intruder is likely to walk. Large areas in an open floor plan, downstairs

ITI ToolBox

The ITI ToolBox is a Windows®-based program that saves you time by simplifying Control Panel programming. Using only a PC, a modem, and a standar d telephone line, Tool Box make s cr ea ting new customer accounts and upd ating the panel settings of exis ting customers simple and quick. See the ITI ToolBox manual and ToolBox’s on- line help for ins tructions to use ToolBox for programming this Control Panel.

The ITI ToolBox has not been investigat ed by UL and

should not be used on UL Listed Systems.

CAUTION!: The Downloader code (option 09) should al-

ways be changed to avoid competitor theft.

ITI CS-5000 Receiver

The CS-5000 Receiver is used t o monitor this security

system.

* = Not Available with Basic Model

Page 6

Installation Instructions Document No. 466-1574.

ITI HomeLink® Transceiver (IHT)

The ITI HomeLink Transceiver is a radio transmitter/ receiver designed to receive signals from the Prince

Universal Transmitter (HomeLink), then retransmit the signals to a securit y system panel, allowing the HomeLink to control the arming, disar ming, and light functions of the security system. The IHT also enables the user to control the g ar age door opener from the HomeLink.

The ITI HomeLink Transceiver has not been investi-

gated by UL and should not be used on UL Listed

Systems.

SWS*

The Supervised Wireless Siren (#60-736-95) annun-

ciates alarm appropriate sounds and because of its

back-up battery, functio ns when th e power is off . Su-

pervised means that the siren will notify the Control

Panel during trouble conditions such as low battery,

power failure, etc.

Carbon Monoxide (CO) Alarm

The Learn Mode CO Alarm (#60-652-95) alerts users to hazardous levels of carbon monoxide gas. If dangerous concentrations of gas are present, the CO Alarm’s red indica tor light comes on, its internal siren goes off, and it transmits an alarm to the Control Panel. The Control Panel sounds its own alarm and calls the central station.

Interrogator

200 Audio Verification Module

(AVM)*

The AVM (#60-687) gives the central station operator the ability to hear what’s happening at the premises during an alarm and speak dire ctly to the system use r. The operator can then determine how se rious an alarm is, find out what kind of help is nee ded, and dis pat ch the appropriate as sistance . Only one AVM may be installed per Control Panel.

Note: Use of the above modu le ha s not been investigat ed by UL.

Note: Use of the SWS has not been investigated by UL.

Emergency Planning Floor Plan

Use the following guidelines when drawing an emergency planning floor plan for the homeowner:

• Show all building levels.

• Show exits from each room (2 exits per room are recommended).

• Show the locations of all security system components.

• Show the locations of any fire extinguishers.

A smoke detector should

Bedroom

Living

Room

Basement

NOTE: Ceiling-mounted smoke detectors should be located in the center of the room or hall, or not less than 4 inches from the wall. When the detector is mounted on the wall, the top of the detector should be 4 to 12 inches from the ceiling.

NOTE: Do not install smoke detectors where normal ambient temperatures are above 100°F or below 40°F. Also, do not locate detectors in front of AC/ Heat registers or other locations where normal air circulation will keep smoke from entering the detector.

NOTE: Additional information on household fire warning is available at nominal cost from: The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. Request Standard No. NFPA74.

Bedroom

Hall

Dining

Kitchen

Room

Living

Room

Dining

Room

Bedroom

Required smoke detector

Heat detector

Indicates smoke detector is optional if door is not provided between basement and recreation rooms.

be located on each level.

Dining

Room

Bedroom

Kitchen

Living

Room

Hall

Bedroom

Living

Room

Basement

Bedroom

In fa mi ly li vi ng un it s w it h mo re than one sleeping area, locate a smoke detector at each area.

Bedroom

Recreation

Room

Smoke detectors should be located between the sleeping area and the rest of the family living unit.

Bedroom

Hall

8557144a

* = Not Available with Basic Model

Page 7

Installat i on Instructions Document No. 466- 1574

Planning Sensor Types & Locations

will be adding. You’l l need to understa nd the ap plication for each sensor. For example, KeyChain Touchpads are typically programmed as sensor type 01

The first step to an easy and successful installation is to decide what areas or items to pro tec t, which lights or appliances to oper at e, and the best location for the Control Panel, touchpad, sensors or sirens. Use the previous information and Table 1 on page 5, Device Location Planning, to note your requirements.

(Portable panic), used to send an intrusion alarm to a central monitoring s tati on. This sen sor typ e is i nstant intrusion, it does not require restoral or supervisory communication with the Control Panel and it is active in 4 arming levels (disarm, arm doors & windows, arm motion sensors, and arm doors/ windows and mo tions sensors).

Use Table 2 on page 6 and Table 3 on pa ge 7 to deter mine the appropriate Sensor Type for the sensors you

Table 1 Sensor/Device Location Planning Table Locations in order as communicated by Control Panel when

adding sensors, except that Remote Locations are not used by the Control Panel, but only used here for planning purposes.

Sensor/Device Name

(use T able 2 on page 6

& T ab le 3 o n page 7 t o

determine sensor type

numbers)

Sensor No.

The following are

examples only.

Sensor Type

Remote Locations

Front Door

Back Door

Garage Door

Bedroom

Guest Room

Child’s Room

Utility Room

Living Room

Dining Room

Bathroom

Laundry Room

Kitchen

Office

Den

Garage

Special Chime

Basement

Upstairs

Downstairs

Hallway

Medicine Cabinet

Closet

Attic KeyChain Touchpad 01 X Door/Window 13 X

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Page 8

Installation Instructions Document No. 466-1574.

Table 1 Sensor/Device Location Planning Table Locations in order as communicated by Control Panel when

adding sensors, except that Remote Locations are not used by the Control Panel, but only used here for planning purposes.

Sensor/Device Name

(use T able 2 on page 6

& T ab le 3 o n page 7 t o

determine sensor type

numbers)

Sensor No.

The following are

examples only.

19 20 21 22 23 24

Sensor Type

Remote Locations

Front Door

Back Door

Garage Door

Bedroom

Guest Room

Child’s Room

Utility Room

Living Room

Dining Room

Bathroom

Laundry Room

Kitchen

Office

Den

Garage

Special Chime

Basement

Upstairs

Downstairs

Hallway

Medicine Cabinet

Closet

Attic

Table 2 Recommended Sensor Types

Device

KeyChain Touchpad 01, 03, 06, 07

Remote Handheld Touchpad

and Touchtalk 2-Way RF

Tou ch pa d*

Indoor Motion Sensor 17 (intrusion), 25 (chime)

Outdoor Motion Sensor 25

Smoke Sensor 26

Exterior Door 10

Interior Door 14

Window Sensor 13

SWS* 33

CO Alarm 34

Freeze & Water Sensors 29

Recommended Sensor

Type

01, 03, 06, 07

* = Not Available with Basic Model

Page 9

Installat i on Instructions Document No. 466- 1574

Table 3 Sensor Type Characteristics

Name/Application Siren Type

Type

Fixed Panic: 24 hour audible fixed emergency button

Portable Panic: 24 hour audible portable emergency buttons

Fixed Panic: 24 hour silent fixed emergency buttons. Status light will not

blink.

Portable Panic: 24 hour silent portable emergency buttons. Status light

will not blink.

Fixed auxiliary: 24 hour auxiliary sensor, such as Pendant Panic

Fixed Auxiliary: 24 hour emergency button. Siren shut off confirms CS

report

Portable Auxiliary: 24 hour portable auxiliary alert button

Portable Auxiliary: 24 hour portable auxiliary button. Siren shut off con-

firms CS report

Special Intrusion: such as gun cabinets and wall safes.

Entry/Exit Delay: Entry/Exit Delay that require a standard delay time.

Chime

Instant perimeter: Exterior doors and windows. Chime

Instant Interior: Interior doors

Instant Interior: Interior PIR motion sensors*

Instant Interior: Interior doors

Instant Interior: PIR motion sensors*

Delayed Interior: interior doors that initiate a delay before going into

alarm*

Delayed Interior: PIR motion sensors that initiate a delay before going

into alarm*

Local Instant Interior: 24 hour local alarm zone protecting anything that

opens and closes. No Report

Local delayed interior: same as group 21, plus activation initiates a delay

before going into alarm. No report.*

Local instant Auxiliary: 24 hour local alarm zone protecting anything that

opens and closes.‡ No report

Local Instant Auxiliary: 24 hour local alarm zone protecting anything that

opens and closes. Sirens shut off at restoral. No report.*

Local Special Chime: Notify the user when a door is opened. Sounds

emit from a local annunciator.* No report

Fire: 24 hour fire, rate-of-rise heat, and smoke sensors§.

Lamp control or other customer feature.‡ No report

PIR motion sensor, sound sensor, or pressure mat.‡ No report

Auxiliary: Freeze and Water Sensors

PIR motion sensor or sound sensor‡ No report

Supervised Wireless Siren (SWS)

Carbon Monoxide Alarm

Rest

Delay

oral

Super

visory

Active in

Levels

Intrusion I No Ye s 1234 Intrusion I No No 1234

Silent I No Ye s 01234

Silent I No No 01234

Emergency I No Ye s 01234 Emergency

Emergency

I No Yes 01234

I No No 01234

Intrusion I Ye s Ye s 1234 Intrusion S Yes Yes 1234

Intrusion S Ye s Ye s 24

Intrusion I Yes Yes 24 Intrusion F Ye s Ye s 234 Intrusion F No Yes 234 Intrusion F Ye s Ye s 34 Intrusion F No Yes 34

Intrusion S Ye s Ye s 34

Intrusion S No Yes 34

Intrusion I Ye s Ye s 1234

Intrusion S Yes Yes 1234

Emergency I Ye s Ye s 01234

Emergency

Three Beeps

I Yes Yes 01234

I No Ye s 01234

Fire I Yes Yes 01234 Silent I Ye s Ye s 01234 Silent I No Yes 01234

Tr ou bl e

Beeps

I Ye s Ye s 01234

Silent I No No 01234 Silent I Ye s Ye s 01234

Emergency I Yes No 01234

*This type is not certified as a primary p rotection circuit for UL-listed systems and is for supplementary use only.

§This type is required for UL-listed residential fire alarm applications.

‡This type has not been investigated by UL. The arming levels are: 0 = Subdisarmed (used to bypass intr usion senso rs which ar e active

24 hrs/day) Only the Master Access Code can enter this level 1 = Disarm

2 = Arm Doors & Windows 3 = Arm Motion Sensors 4 = Arm Doors/Windows & Motion Sensors

Delays: I = Instant Delay (no delay, immediate alarm) S = Standard Delay (alarm sounds after progra mmed entry delay

time) F = Follower Delay (alarm sounds immediately if entry/exit delay is

not active, otherwise alarm sou nds after programmed entry delay time)

Page 10

Installation Instructions Document No. 466-1574.

Planning Control Locations

Control Panel

Locate the Control Panel so th at the alarm sounds can be heard and the Control Panel will be convenient to operate. It must be near an electrical outlet and telephone receptacle.

Remote Handheld Touchpad and Touchtalk 2Way RF Touchpad*

Locate Remote Handheld Touchpads and the wallmounted Touchtalk 2-Way RF Touchpad where t hey will be convenient and offer quick access to the user.

KeyChain Touchpad

KeyChain Touchpads attach to the owner’s key ring or can be conveniently carried.

Planning for Lamp*, Appliance*, Wallswitch*, and Universal/Garage

code. The numbered dial sets the unit number. The unit

number tells the system which device you want to control. Each unit number sh ould be di fferent (unless you want specific li ght s or appliances to b e activated together). The Control Panel recognizes up to 8 unit numbers for sensor-activated, time-activated and entry/exit delay lights. When unit numbers 9-16 are used for lamp modules, they can only be controlled by an all on or all off command.

A lamp will flash to the ar ming level if its unit number is set to 10. A lamp set to unit number 10 will flash once if the Control Panel is disarmed, twice if doors & windows are armed, etc.

The remote siren can be set to any unit number to hear alarm sounds. Set it to unit number 9 to also hear ar ming level beeps, status beeps, and trouble beeps.

To Fill Out the Home Control Planning Table:

Note: Do not use a la mp m odule to con trol appl iance s, use an appliance module, since the wattage rating on Lamp Modules is less than on Appliance Modules.

Door* Module Control

As you program the modules, the Control Panel asks you to choose the house code, unit number and activation method. Fill out Table 6 on page 9, Home Control Planning Table, before you begin programming.

The system can control 8 in div idu al unit numbers on Lamp, Wallswitch, App liance, and Univer sal/Garage Door Modules.

Setting the House Code and Unit Number

Each device (lamp, appliance, garage door, etc.) controlled by t he Control Pan el must have an identification setting. The modu l es use two dials to set identification codes: on e with l etters A through P and one with numbers 1 through 16.

The lettered dial s ets t he hous e code. The h ouse cod e enables the system to differentiate this home from other homes in the area. Set all modules (except the remote siren) and the Control Panel to the same house

1. Set the house co de on all the Modul es, excep t the remote siren to the same letter.

Note: The house code instructions which come with the Powerhorn Siren won’t work with this Control Pa nel. Foll ow the house-code instructions given here.

Set the Remote Siren house code to the next alphabetical letter. For example, if the house code is B, set the remote siren’s house code to C.

2. Set the Module unit numbers.

Note: If you are using a Universal Module to operate a garage door, make sure to assign a unique unit n umber to this Module choosing from 1-8.

3. List the location of the lamp or applia nce in the Location column of Table 6 on page 9.

4. Write the location of each Lamp Module on an adhesive note and label the module.

5. Decide if the device should be activated by sensors, entry/exit delay, time, or a combination. An example of sensor activation is using a motion sensor to turn on a light. Record the information in the appropriate columns.

* = Not Available with Basic Model

Page 11

Installat i on Instructions Document No. 466- 1574

Use the following three ta bles to help you further plan module insta llation.

Table 4 Unit Number Assignments*

Unit Number

(1 through 16)

1-8 Used for sensor-activated, time-activated, and entry/exit delay lights.

Sensor-activated lights are enabled and disabled pressing the LIGHTS Sensor Activated button on the Control Panel. Time-activated lights are enabled and disabled by pressing the LIGHTS Time Activated button on the Control Panel.

If using the universal module to operate a garage door, be sure to assign a unique unit number.

The STAR button on the KeyChain Touchpad activates the universal module to open the garage door or to turn on special lights if progra mmed.

9-16 Used for lamp module s and controlled by an all on or all off command.

9 Used for remote siren to hear arming level beeps, status beeps and trou bl e beeps.

If set to any other number the user will hear only alarm sounds.

10 Lamps will flash to arming level.

Result

Table 5 House Code Assignments*

House Codes Results

A through O Set all modules to the sa m e ho us e co de

except the remote sirens

Next Higher House Code Remote Siren needs to be the next higher

alphabetical letter

Table 6 Home Control Planning Table*

Module Activated by Time Activated

Unit # Type Location Sensor Entry/Exit Start Time Stop Time

Example Lamp Hall lamp Motion Yes 8 p.m. 10:30 p.m. 1 2 3 4 5 6 7 8

* = Not Available with Basic Model

Page 12

Installation Instructions Document No. 466-1574.

Planning System Access Codes

Use the following to plan system Access Codes. Fill out Table 7 on page 10 to use when programming these codes.

Utility Access Code 1

This access code is used during installation. The default utility a ccess code is 4321. This code can be used for all programming.

Utility Access Code 2

The default access code is 4321. This access code is used for all programming except changing utility access code 1 and changing options 4, 5, 6, 8, 9, 12, and

13.

The Panic Code is able to disarm or sub disarm the panel and send a silent alarm to the Central Station. There will be no indication of an alarm at the panel.

Table 7 System Access Codes

Type Default

Utility Access Code 1 4321 Utility Access Code 2 4321 Master Access Code 1234 Access Code 1 None Access Code 2 None Access Code 3 None Access Code 4 None Access Code 5 None Panic Code None

Installer Settings

Master Access Code

The default Master Access Code is 1234. This user code is used to: disarm the Control Panel, subdisarm the Control Panel, program options 1 through 3, 36, 37, 41 - 43, program light control, set the system clock, program the master code, program access codes 1-5, program the panic code, and per form a sensor or phone test.

Note: If the installer deletes the master access code, the owner may enter program mode by pressing cancel.

Access Codes (1 - 5)

The Control Panel can have u p to 5 secondary user access codes. These could be used by children, a baby sitter, or a service person. Th ese codes cannot be used for programming.

Panic Code

Planning System Options

Use the following to plan system Options. See Table 18 on page 19 for a complete listin g of al l system options and their c haracteris tics. Fill out the l ast colu mn of this table to use when programming.

Option 01: Panel Piezo Beeps

Add turns on panel beeps that sound when an access code is entered or when the arming level is changed. The arming buttons wil l cause bee ps accordi ng to the arming level. See Table 8 on page 11 for a det ailed explanation of panel piezo beeps.

Delete turns off panel piezo beeps.

Option 02: Panel Voice

Add enables the panel’s voice. Delete disables the panel’s voice.

Note that the panel voice is always on for sta tus messages, open sensor responses, and when in program mode.

Page 13

Table 8 Panel Piezo Beeps

Activity Beep Response

Installat i on Instructions Document No. 466- 1574

ARM Doors & Windows

ARM Motion Sensors Exit delay beeps sound 3 times when you arm and 3 times at the end of the delay time;

ARM Doors/Windows & Motion Sensors

DISARM 1 beep CHIME DOORS 2 beeps (when programmed) CHIME SPECIAL

MOTION Trouble Beeps 6 beeps every minute. Press SYSTEM STATUS button to stop beeps for 4 hours No Activity 20 beeps every minute for 5 minutes (when programmed)

Option 03: Latchkey

Add programs the Latchkey time. If Latchkey is enabled when the Control Panel is armed and the Control Panel is not disarmed by the preprogrammed time, the Control Panel will call in a Latchkey alarm at the programmed time.

Exit delay beeps sound 2 times when you arm and 2 times at the end of the delay time; Entry delay beeps sou nd 2 times ev ery 5 seco nds and 2 tim es per seco nd during the last 10

seconds

Entry delay beeps sou nd 3 times ev ery 5 seco nds and 3 tim es per seco nd during the last 10 seconds

Exit delay beeps sound 4 times when you arm and 4 times at the end of the delay time; Entry delay beeps sou nd 4 times ev ery 5 seco nds and 4 tim es per seco nd during the last 10

seconds

3 beeps (when pr ogrammed)

Set Phone Mod 2 (option 13) to 8 or 9. The Control Panel will call a numeric page r twi ce for ea ch repor t. Pagers that require t he Control Panel to dial more than 22 digits will not work. Silent alarms report to a pager as an intrusion alarm. See Table 17 on page 17 for more reporting information.

The system clock must be set for Latchkey to function.

Delete turns off this option and Latchkey cannot be enabled when the Contro l Panel is armed.

Option 04: Primary Phone Number

Add programs the pri mary ph one number to be c alled when there is an alarm. The phone number will call the central station.

Delete removes the primary phone number.

Option 05: Secondary Phone Number

Add and Delete function the same as they do for the primary phone number. This number can be to a numeric pager or a central st atio n. When us ing it t o call a numeric pager, program this phone number with 2 pauses (press the test button to progra m a pause) at the end of the number. Some pagers may require 3 or 4 additional pauses be appended to the phone number.

Option 06: Downloader Phone Number

Programs the ITI ToolBox Downloader telephone number.

Add and Delete function the same as they do for the primary phone number.

Option 07: Account Number

Add programs the account number. Delete resets it to 00000.

Option 08: Phone Lock

Add enables phone lock. Options 04, 05, 06, 08, 09, 12, and 13 will not be cleared if the system memory is cleared and phone lock is on.

Delete disables phone lock.

Page 14

Installation Instructions Document No. 466-1574.

Option 09: DL Code (Downloader Code)

Add programs the downloader access code. The Downloader Code is used during Control Panel programming with the IT I ToolBox. The Cont rol Panel’s downloader code must match the downloader access code in the ITI ToolBox a cco unt in or der to program the Control Panel using the ITI ToolBox.

Delete resets the code to 12345.

CAUTION!: The downloader code should always be changed to avoid competitor theft.

Option 10: Entry Delay

Add programs the entry delay. Enter time in seconds. The range is 005-120 seconds (3 digits must be entered). Entry delay beeps will sound when the delay is activated. The panel will sound beeps corresponding to the arming level eve ry 5 seconds. For example, you will hear 2 beeps every 5 seconds if the panel is arme d to level 2. The entry dela y beeps will sound ever y second during the la st 10 seconds of the d elay to warn the user that the delay is about to expire.

Delete sets the delay to 5 seconds.

Table 9 Phone Mod 1

Enter # Reports Format

0All SIA 1All Contact ID 2Alarms SIA 3Alarms Contact ID

Alarms include: Fire, Intrusion, Emergency, Silent, and Alarm Cancels.

Non-Alarms include: Latchkey, No Activity, Openings, Closings, Fail to Open, Fail to Close, Force Armed, AC Power Failure, CPU Low Battery, and Trouble Restorals.

All includes: Alarms and Non-Alarms. UL has only verified compatibility with the ITI

CS5000 Digital Alarm Communicator Receiver.

Option 13: Phone Mod 2

Add sets the report co ntent and format that th e secondary phone number uses. Range is 0-9.

For UL listed systems, the entry delay should not exceed 45 seconds.

Option 11: Exit Delay

Add programs the exit delay. Enter time in seconds. The range is 005-120 seconds (3 digits must be entered). The exit delay bee ps will occur when the panel is armed and when the exit delay has e xpired. The exit delay beeps correspond to the arming level. For example, you will hea r 2 beeps if armin g to leve l 2. The panel will sound three sets of warning beeps if a sensor that requi res r estor al i s open dur ing t he ex it de la y if auto arm is off (opt ion 38). The panel will protest i f a sensor that requires restoral is open during the exit delay if auto arm is on (option 38).

Delete sets the delay to 5 seconds. For UL listed systems, the exit delay should not ex-

ceed 45 seconds.

Option 12: Phone Mod 1

Add sets the report content and format which the primary phone number uses. The range is 0-3.

Delete sets the phone mod to 0.

Table 10 Phone Mod 2

Enter # Reports Format

All

Alarms

Non-Alarms

Phone 1 failure

Latchkey, No Activity, Phone Test, Openings, Closings, Fail to Open/ Close, AC Power Restorals/Failures

Same as Phone Mod 8 plus Alarms

SIA Contact ID SIA Contact ID SIA Contact ID SIA Contact ID Pager

Pager

Option 14: DTMF Dialing

Add enables DTMF dialing. Delete enables pulse dialing.

Delete sets the phone mod to 0.

Page 15

Installat i on Instructions Document No. 466- 1574

Option 15: No Activity

Add enables the no acti vity time-out. Program the no activity time-out in hours. The range is 02-24 hours (2 digits must be entered). A no activity alarm will be called in if the programmed amount of time passes and the panel is in level 0, 1, or 2 and no activity has occurred.

No activity is defined as: a key has not be pressed from the panel or a tou chpad and a sensor has not been tripped (except one that is type 25).

Delete disables the no activity time-out.

Option 16: Auto Phone Test

Add enables the auto phone test. Program th e auto phone test frequency in days. The range is 001 - 254 days (3 digits must be entered). The start time for the auto phone test begi ns 12 hours a fter the Control Pan el is powered up.

Delete disables auto phone test.

Option 17: Dialer Delay

Add enables the dialer delay. Program the delay in seconds. The range is 001-120 second s (3 digits must be entered). This option causes the Control Panel to wait the programmed time before calling the central station. Alarms acti vated by sensor s that are typ e 0-8, 26, and the emergency button on the f ron t of t he con trol panel or on any of the touchpads will always be called in immediately.

Delete disables the dialer delay. For UL installations, dialer delay time cannot be

greater than 45 seconds.

Note: The Control Panel wi ll not wa it th e progra mmed dia ler delay to call in an alarm if the Contro l Pane l is dis arm ed before the dialer delay expires and openin g reports ar e on. Both the alarm and opening report will be called in immediately.

Option 18: Alarm Cancel

Option 19: Supervisory Time (SUPSYNC)

Add sets the supervisory time. Program the time in hours. The range is 02-24 hours (2 digits must be entered).

Delete resets SUPSYNC to 2 hours. For UL listed systems, th e SUPSYNC shall not ex-

ceed 4 hours.

Option 20: Manual Phone Test

Add allows the user to perform a manual phone test. Delete disables manual phone test.

Option 21: Opening Reports (Disarming Repor t s)

Add enables opening r eports. Openin g repo rts will be sent to the central station if the Control Panel is disarmed from a higher arming level.

Delete disa bles opening reports .

Option 22: Closing Reports (Arming Reports)

Add enables closing reports. Closing reports will be sent to the central station if the Control Panel is armed to level 2, 3, or 4.

Delete disables closing report.

Table 11 User Codes for Opening and

Closing Reports

Arm or Disarm with:

Control Panel, Touch talk 2-Way RF Touchpad, & Handheld Touch Pad

FOB 1-24 (sensor num-

Master Code 30 Access Codes 1-5 31-35 Panic Code 36

Reports as

User:

ber)

Add enables alarm cancel. Program the tim e in minutes. If the Control Panel is disarmed from an alarm state within the programmed time, the Control Panel will send an alarm cancel message. The ran ge is 001254 minutes (3 digits must be entered). If programmed to 255, cancels will always be sent to the central station.

Delete disables the alarm cancel.

Option 23: Force Armed

Add enables fo rce armed reports. A force armed report will be sent to the ce ntral stati on if a sens or is in directly bypassed.

Delete disables force armed reports.

Page 16

Installation Instructions Document No. 466-1574.

Option 24: AC Power Failure

Add enables AC power failure reports. The panel LEDs will shut off and an AC power failure report will be sent to the central station if the Control Panel has lost power fo r 15 minutes. Th e Control Pane l will report AC po wer restoral when power returns to the Control Panel.

Delete disables AC power failure a nd restor al repo rts.

Option 25: CPU Low Battery

Add enables CPU low battery reports. A low battery report will be sent to the central station when the Control Panel’s lithium battery voltage drops below 6.2 volts or the rechargeable battery drops below 6.5 volts.

Delete disables CPU low battery reports.

Option 26: Fail to Communicate

Add enables fail to communicate. If the Control Panel is not able to c onne ct to the CS when it’s try ing to report an alarm, the Contr ol Panel will indicate this wi th trouble beeps and in the status message.

Delete disables fail to communicate.

Option 27: Ring/Hang/Ring

Add enables ring/hang/ring to use with ToolBox and remote phone acc ess. T his fea ture is u seful when programming a Control Panel i n a home with an answering machine.

Delete disables ring/hang/ring. The Control Panel will not answer.

Program ring/hang/ring by number.

Table 12 Ring/Hang/Ring Program Numbers

again.

3. The Control Panel should answer on the first ring.

Program # 2 - Repeat steps 1 & 2 before the Control Panel will answer.

Program # 3 - Repeat steps 1 & 2 twice before the Control Panel will answer.

The following table identifies the phone commands to be used when using remote phone control.

Table 13 Phone Commands for Remote

Access*

Control Panel Function Phone Command

DISARM * + CODE + 1 ARM Doors/Windows * + CODE + 2 ARM Doors/Windows with No

Entry Delay ARM Motion Sensors * + CODE +3 ARM Motion Sensors with

Latchkey ARM Doors/Windows and

Motion Sensor s ARM Doors/Windows with No

Entry Delay and Motion Sensors with Latchkey

Toggle Lights * + CODE + 0 System Status * + CODE + # + 1 Audio Verification * + CODE + 5 + X (X = a

CODE = any access code except utility access codes 1 and 2

* + CODE + 2 + 2

* + CODE + 3 + 3

* + CODE + 2 + 3

* + CODE + 2 + 2 + 3 + 3

command from the audio verification command set). See Table 15 on page 15

Program # Control Panel will answer after:

1 ring/hang/ring or 10 rings 2 ring/hang/ring/ha ng /rin g or 10 rin gs 3 ring/hang/ring/hang/ring/hang/ring or 10 rings 4 10 rings

If ring/hang/ring is programmed as: Program # 1 -

1. Call the Control Panel and let the phone ring twice then hang up.

2. Wait 10-40 seconds and call the Control Panel

Option 28: No Delay from KeyChain Touchpad

Add arms with no entry delay when using the KeyChain Touchpad.

Delete arms with an entry delay when using the Ke yChain Touchpad.

Option 29: Control Panel Alarms

Add enables the Control Panel’s piezo to sound alarms. Alarms will sound from the Control Panel.

* = Not Available with Basic Model

Page 17

Installat i on Instructions Document No. 466- 1574

Delete disables the Contro l Panel’s piezo from sounding alarms. Alarms will not sound from the Control Panel.

For UL listed systems, at least one listed extern al audible signal device shall be used if the external piezo is disabled.

Option 30: Panic Alarms

Add enables all panic alarms (intrusi on, auxiliary, and fire) initiated from the Control Panel. Use the decal included with the Control Panel if this option is on.

Delete disables intrusion, auxiliary, and fire panic buttons on the control panel. The emergency button on the control panel is always active.

Option 31: Day of Week

Add will program the day of week based on a programmed number. The day of wee k may be viewed in the event buffer using ToolBox.

alarm, pick up the CS phone.

2. Press the * button on th e phon e to start the audio session.

3. Press 1 or 0 to speak and 3 or 6 to listen.

4. Press 99 to terminate the session .

Note: To conduct an au dio s ession using remote phone access see Table 13 on page 14.

Table 15 Audio Verification Set

Phone

Button(s)

1 Speak

3 or 6 Listen

7 Exten d session for 90 more seconds

88 Terminates session with call back (the

99 Terminates session with no call back

Audio Verification System

panel will answer on the first ring if called within 5 minutes)

Table 14 Day of Week by Number

0 Sunday 1 Monday 2Tuesday 3 Wednesday 4 Thursday 5Friday 6 Saturday

Delete sets day of week to 0.

Option 32: 300 Baud

Add enables 300 baud communication. Enable this option for faster communication

Delete enables 110 baud communications

Option 33: 2-Way Voice*

Add enables 2-way voice communications between the security system site and a monitoring station . 2way voice is also availa ble to the owner if Ring/Hang / Ring (option 27) is on.

Delete disables 2-way voice.

Option 34: Fail to Open

Add enables fail to open. If the panel has not been disarmed by the programmed opening time, the panel will call in a fail to open alarm to the Central Station and/or a pager.

Delete disables fail to open.

Option 35: Fail to Close

Add enables fail to close. If the panel has not been armed by the programmed opening time, the panel will call in a fail to close alarm t o t he Cent ral Station and/or a pager.

Delete disables fail to cl ose.

Option 36: Sensor Activated Light Lockout Start Time*

Add enables sensor activ ate d li ght lockout start time. The panel will not turn on a light between the programmed start time (option 36) and the programmed stop time (option 37), even if sensor activated lights are on. Both options must be pr ogr ammed for this option to work correctly.

Do the following to conduct an audio session:

1. After the panel has completed reporting the

Delete disables sensor activated light lockout start time. The panel will tu rn on a light acti vated by a sensor at all times if sensor activated lights are enabled.

* = Not Available with Basic Model

Page 18

Installation Instructions Document No. 466-1574.

Option 37: Sensor Activated Light Lockout Stop Time*

Add enables sensor activated light lockout stop time. The panel will not turn on a light, between the programmed start time (option 36) and the programmed stop time (option 37), even if sensor activated lights are on. Both options must b e p rogr amme d f or t his

option to work correctly.

Delete disables sensor activated light lockout stop time. The panel will turn on a light ac tivated by a sensor at all times if sensor activated lights are enabled.

Option 38: Auto Arm

Add enables auto ar m. Any sensor that require s res toral and is open when the panel is armed will automatically be bypassed whe n th e panel is don e prot esting. The panel will protest for 4 minutes, then auto arm. Pressing the ARM Doors & Windows bu tton a second time will stop the control panel protest and auto arm the system. Pressing th is butt on a t hir d ti me will arm with no entry delay. The panel will go into alarm if an instant alarm senso r is opened du ring an exit delay. A sensor learned as type 26 can never be bypassed.

Delete disables auto arm. Any sensor that requires restoral and is open when the exit delay expires will automatically be b ypas sed. Beeps indicating th e ar ming level will s ound four times when the contr ol panel is armed and one time when the exit delay ends. The panel will go into alarm if an instant alarm sensor is opened during an exi t delay. A sensor l earned as type 26 can never be bypassed.

Option 39: Siren Time Out

Add programs siren time out from 1 to 30 minutes. The default siren time out is 4 minutes.

Delete siren never time out.

Option 40: Trouble Beeps

Add enables trouble beeps. If there is a tr oubl e co ndi tion, six beeps will sound every minut e. If the panel i s armed, disarmed, or status is pressed, the trouble beeps will stop and then resume 4 hours later.

Trouble beeps will be heard if:

• There is AC power failure.

• The CPU battery is low.

• There is a sensor failure.

• There is sensor trouble.

• There is a fail to communicate problem.

• The no activity timer has timed out. Trouble beeps will continue for 5 minu tes and if th e panel does not see activity, the trouble beeps will stop and the panel will call the CS to report the no activity.

Delete disables trouble beeps, so tha t if a probl em occurs the control panel will not notify the owner with trouble beeps.

Option 41: Chime Voice

The panel has two chime modes which may be enabled by pressin g the approp riate butt on on the pan el.

CHIME Doors

Chime doors is a chi me sound (two beeps) th at will be emitted from the inte rior siren output, the pa nel siren, SWS, and the X-10 powerho rn siren (if s et to unit #9) when a door/window sensor which is ty pe 10 or 13 is activated. If th ere are no sen sors learned as type 10 o r 13, this function will not be avail abl e. The panel will announce which sensor was tri pped if chime voice is on and the sensor was opened while the panel is disarmed.

CHIME Special Motion*

Chime special motio n i s a chi m e s ound (three beeps) that will be emitted from interior siren output, the panel siren, SWS, and the X-10 powerhorn siren (if set to unit #9) when a chime sensor that is type 25 is activated (the alarm sta te is sent to the pa nel). If there are no sensors learned as type 25, this function will not be available. The panel will announce which sensor was tripped if chime voice is on and the sensor was opened while the panel is disarmed.

Add enables chime voice. The panel will announce which chime sensor has b een tripp ed if the chime f eature is enabled.

Delete disables chime voice. The panel will not announce which chime sensor has been tripped even if the chime f eature is enabled.

Option 42: Speaker Level*

Add sets speaker level to the high voice level. Delete sets the speaker level to the low voice level.

* = Not Available with Basic Model

Page 19

Installat i on Instructions Document No. 466- 1574

Option 43: Pager Phone Number

Add enables pager pho ne number. Prog ram t he page r phone number. The phone number can only call a pager. Some pagers may require 3 or 4 additional pauses be appended to the phone number.

Delete disables pager phone number. The phone number will not be called in an alarm situation.

Option 44: Pager Phone Mod 3

Add enables pager p hone mod 3 sets the r eport content and format the pager ph one number uses. Us e the f ollowing table to determine the value to enter.

Delete sets pager phone mod to 8.

Table 16 Pager Phone Mod Format

Enter

8 Latchkey, No Activity, Phone Test,

Openings, Closings, Fail to Open/ Close, AC Power Restorals/Failures

9 The same as Phone Mod 8 plus Alarms Pager

Reports Format

Pager

Option 45: Sensor Alarm Restoral

Add enables sensor alarm r estoral. This sends a report to the centr al station when a restoral sensor that is in alarm is restored.

Delete disables sensor alarm restoral reports.

Option 46: Fire Shutdown - AVM*

Add enables fire shutdown - AVM. This option allo ws the panel to turn off the sirens during a two way voice session with the user and the central station. Beeps will sound every 10 seconds while the sirens are off.

Delete disables fire shutdown - AVM. I f this option is turned off, the sirens will not shut off during a two way voice session.

Option 47: AVM Mode*

Add enables AVM mode. This allows the central station to hang up an d c all t he panel back for a t w o wa y voice session.

Delete disables AVM mode. When this option is off, the two way session will start immediately.

Table 17 Pager Reporting Message

Use the following table to determ ine what the numer ic message is reporting.

Reports Numeric Message

Phone Test -101 -101 AC Power Restoral -102 -102 AC Power Failure -103 -103 Latchkey -104 -104 No Activity -105 -105 Panic Code -106 -106 Emergency -107 -107 Intrusion -108 -108 Fire -109 -109 Openings -110 -110 Closings -111 -111 Fail to Open -112 -112 Fail to Close -113 -113

* = Not Available with Basic Model

Option 48: Panic Talk*

Add enables panic talk. This allows the central station to listen an d talk to the user during a silent alarm. (Sensor type 02 or 03 or if the Panic Code was entered).

Delete disables panic talk. When this option is turned off, the central station may only list en during a silent alarm.

Option 49: Rechargeable Battery

Add enables the rechargeable battery to be used. Delete enables the lithium battery to be used.

Option 50: RF Jam Detect

Add enables RF jam detect. This allows the Control Panel to detect RF int erference. The contro l panel will call the Centr al S tat i on if RF jam dete ct i s on and the panel receives a constant 319.5 MHz signal.

Option 50 Detected is the status message for this option.

Delete disables RF jam detect. When this option is turned off, the Contro l Panel is unable to detec t RF interference.

Page 20

Installation Instructions Document No. 466-1574.

Option 51: 24 Hour Battery Test

Add sets battery test period to 24 hours. This feature is only useful when using a non-rechargeable UltraLife 9V lithium battery because it extends battery life.

Delete sets battery test period to 4 hours.

Option 52: High Level Status

Add sets status beeps and arming level beeps to high volume.

Delete sets status beeps and arming leve l beeps to low volume.

Option 53: Hardwire Siren Supervision

Add t urns hardwire sire n supervision on. Turn th is option on if installing a ha rdwire siren and supervision is desired.

See the “Wiring the Control Panel” on page 21 for the correct EOL resistor connection.

Delete turns hardwire supervision off and is the appropriate setting if hardwire sirens are not being connected.

Reset Memory to the Factory Defaults

If it becom e s necessary to set all programming back to the factory defaults, do the following:

1. Open the Control Panel cover.

2. Unplug the transformer and the battery.

3. Simultaneously press Cancel, Clock Set, and Minutes.

4. Restore power to the panel with either the battery or the transformer while pressing these three buttons.

5. Plug in the transformer or connect the battery.

NOTE: If Phone Lock is on, options 04, 05 , 06, 08, 09, 12, and 13 will not reset to their defaults.

Page 21

Installat i on Instructions Document No. 466- 1574

Table 18 Programmable Options

Who Can

Change:

U1 - Utility

Op-

tion #

01 Panel Piezo Beeps On Off On/Off U1 U2 M 02 Panel Voice On Off On/Off U1 U2 M

Function Default Delete Range

Access Code 1;

U2 - Utility

Access Code 2;

M - Master;

Installer Settings

03 Latchkey Option Off Off 12:00 AM-

11:59 PM 04 Primary Phone Number None None 22 digits U1 05 Secondary Phone Number None None 22 digits U1 06 Downloader Phone Number None None 22 digits U1 07 Account Number 00000 00000 00000-

99999 08 Phone Lock Off Off On/Off U1 09 Downloader Code 12345 12345 00000-

99999 10 Entry Delay 030 sec 005 s e c 005-120 sec U1 U2 11 Exit Delay 030 sec 005 sec 005-120 sec U1 U2 12 Phone Mod 1 0 0 0-3 U1 13 Phone Mod 2 0 0 0-9 U1 14 DTMF On Pulse On/Off U1 U2 15 No Activity Report Off Off 02-24 hrs U1 U2 16 Auto Ph on e Test (Must be enabled for UL

Listed systems)

Off Off 001-254

days

U1 U2 M

U1 U2

17 Dialer Delay Off Off 001-120 sec U1 U2 18 Alarm Cancel Report Off Off 001-255 min U1 U2 19 Supervisory Time (SUPSYNC) 12 hrs 02 hrs 02-24 hrs U1 U2 20 Manual Phone Test On Off On/Off U1 U2 21 Opening Reports Off Off On/Off U1 U2 22 Closing Reports Off Off On/Off U1 U2 23 Force Armed Report Off Off On/Off U1 U2 24 AC Power Failure Report (Must be enabled

for UL Listed systems)

25 CPU Low Battery Report (Must be en abled

for UL Listed systems)

26 Fail to Communicate (M ust be enabled for

UL Listed systems)

27 Ring/Hang/Ring 1 Off 1-4 U1 U2

Off Off On/Off U1 U2

On Off On/Off U1 U2

Page 22

Installation Instructions Document No. 466-1574

Table 18 Programmable Options

Op-

tion #

28 No Delay from KeyChain Touchpad Off Off On/Off U1 U2 29 Panel Piezo Alarm On Off On/Off U1 U2 30 Panic Alarms Off Off On/Off U1 U2 31 Day of Week 0 0 0-6 U1 U2 32 300 Baud Central Station Communications On 110 Baud On/Off U1 U2 33 Audio Verification* Off Off On/Off U1 U2

Function Default Delete Range

Who Can

Change:

U1 - Utility

Access Code 1;

U2 - Utility

Access Code 2;

M - Master;

Installer

Settings

34 Fail to Open Off Off 12:00 AM -

11:59 PM

35 Fail to Close Off Off 12:00 AM -

11:59 PM

36 Sensor Activated Light Lockout Start

Time*

37 Sensor Activated Light Lockout Stop Time* Off Off 12:00 AM -

38 Auto Arm Off Off On/Off U1 U2 39 Siren Time Out 04 min Siren

40 Trouble Beeps On Off On/Off U1 U2 41 Chime Voice Off Off On/Off U1 U2 M 42 Speaker Level* On Low On/Off U1 U2 M 43 Pager Phone Number Off Off 22 digits U1 U2 M 44 Pager Phone Mod 3 9 9 8 or 9 U1 U2 45 Sensor Alarm Restoral Off Off On/Off U1 U2

Off Off 12:00 AM -

11:59 PM

01 - 30 minnever times out

utes

U1 U2

U1 U2 M

U1 U2

46 Fire Shutdown - AVM* Off O ff On/Off U1 U2 47 Audio Verification Mode* Off Off On/Off U1 U2 48 Panic Talk - AVM* Off Off On/Off U1 U2 49 Rechargeable Battery Off Off On/Off U1 U2 50 RF Jam Detect Off Off On/Off U1 U2 51 24 Hour Battery Test Off Off On/Off U1 U2 52 High Level Status Off Off On/Off U1 U2 53 Hardwire Siren Supervision Off Off On/Off U1 U2

* = Not Available with Basic Model

Page 23

Installat i on Instructions Document No. 466- 1574

Wiring the Control Panel

This section describes how to:

• connect hardwire interior and exterior sirens (if being installed)

• connect hardwire sensors

• connect garage door opener module

• connect the power transformer

• connect the backup battery

• connect a phone line

Connecting Hardwire Interior Sirens

The following ITI interior sirens may be used with this Control Panel:

• LD105 Siren (13-374)

• Phone Jack Siren (60-683)

Turn option 53 on for siren supervision. When option 53 is on and a hardwire exterior siren is not connected, a 47k ohm resistor (two 47 k ohm resistors are sh ipped with the Control Panel ) must be con nected acros s the positive and negati ve terminal s. If a 47k ohm resi stor or a siren is not connected to the exterior siren te rminals, SYSTEM STATUS will say Module 1 failure.

Connecting a Hardwire Exterior Siren

The following ITI e xterior siren may be used with this Control Panel:

• Hardwire Exterior Siren (13-046 ) Turn option 53 on for siren super vision. When option

53 is on and a hardwire in terior siren is not c onnected, a 47k ohm resistor (two 47k ohm resistors are sh ipped with the Control Panel) must be conn ected acros s the positive and negati ve terminal s. If a 47k ohm resi stor or a siren is not connected to the interior siren terminals, SYSTEM STATUS will say Module 2 failure.

Wire sirens to be su pervised by using a 4.7k oh m EOL resistor, included with the siren.

Only one hardwire exterior siren may be connected. See figure 3 below for wiring connections.

Note: Two 47k ohm resist ors are in cluded with the Control Panel. These should not b e used for EOL resistors when wiring sirens.

All inputs are Class II

power-limited circuits.

AC POWER

9 VAC

HARDWIRE INPUTS/SIREN

Hardwire

Input 1

Exterior

Siren

–

Hardwire

and

Power

Common

Hardwire

Input 2

Interior

Siren

–

Follow the siren installation instructions included with the siren for siren specific EOL resistor connections. Only one hardwire interior siren may be connected. See figure 2 below for a generalized wiring connection.

HARDWIRE INPUTS/SIREN

Hardwire

Input 1

Exterior

Siren

–

All inputs are Class II

power-limited circuits.

47k

Figure 2. Supervised Interior Siren Connections

Hardwire

and

Power

Common

Hardwire

Input 2

Interior

SIREN

8988G48C.DS

Siren

–

47k OHM RESISTOR

4.7k OHM

BLACK

RESISTOR

RED

HARDWIRE

EXTERIOR SIREN

PART NO. 13-046

8988G20E.DS4

Figure 3. Supervised Exterior Siren Connections

Connecting Hardwire Sensors

This section shows how to wire hardwire sensors to the Control Panel. For more programming information on installing hardwire devices, “Programming Sensors” on page 25. Wire sensors to be supervised by using a 47k Ohm resistor (included with the Control Panel).

Page 24

Installation Instructions Document No. 466-1574.

HARDWIRE INPUTS/SIREN

All inputs are Class II

power-limited circuits.

Normally

Closed

Hardwire

Input 1

Exterior

Siren

–

Hardwire

and

Power

Common

47k

Hardwire

Input 2

Interior

Siren

–

Normally

Closed

8988G22B.DS4

Figure 4. Wire Hardwire Sensors Normally Closed

Connecting the Universal/Garage Door Opener Module*

Use the followin g to connect a universal module to be used to open a garage door:

1. Set the unit code of the universal module to a

unique unit number between 1 and 8.

2. Set the house code to the house code for the

installation.

3. Set the module’s switches to momentary and

relay only.

4. Connect the terminals on the universal mod- ule to the button terminals on the garage door opener.

5. Plug the universal module into a wall outlet.

All inputs are Class II power-limited circuits.

AC POWER

9 VAC

CLASS II POWER

TRANSFORMER

PART NO. 22-091

HARDWIRE INPUTS/SIREN

Hardwire

Input 1

Exterior

Siren

–

Hardwire

and

Power

Common

Hardwire

Input 2

Interior

Siren

8988G03B.DS4

–

Figure 5. Power Transformer Control Panel Connections

Connecting the Backup Batteries

Installing a Non-rechargeable Battery

Connect a 9-Volt lithium battery (ITI #34-037) to the battery strap as shown in Figure 6.

Note: See the “Programming Light and Appliance Controls*” on page 26 to program a KeyChain Touchpad to open a garage door.

Connecting the Power Transformer

Connect the power transfor mer as shown i n Figure 5. Plug the transformer into an unswitched outlet

Note: Failure to terminate unused inputs as shown will cause the Control Panel to indicate module 1 and module 2 failure.

9 V O L T B A T T E R Y

8 9 5 9 G 1 7 D . D S F

Figure 6. Control Panel Battery Installation

Note: The Control Panel will initially indicate a low battery

by lighting the SYSTEM STATUS button. If this button is pressed the Control Panel will announce, System low bat- tery.

The Control Panel does a battery test every 4 hours and will clear th e status messa ge if the batt ery is good.

Perform a sensor test, “Testing Sens ors” on page 30, to perform an immediate battery test.

* = Not Available with Basic Model

Page 25

Installat i on Instructions Document No. 466- 1574

Installing a Rechargeable Battery

Plug the AC power transformer into an unswitched outlet.

Connect the rechargeable battery (#34-051 or #34-

052) as shown below in 7 Option 49 must be turned on in order for the charging circuit to be activated.

The rechargeable battery will be fully charged after nine hours. The syste m wi ll h ave a low batte ry r eport when checking system st atus unt il th e batt ery is f ully charged.

If a rechargeable battery needs replacing, the control panel must be power-cycled in order for the new battery to become fully char ged. To power-cycle the con trol panel do the following:

1. Unplug the AC power transformer and battery.

2. Plug in the AC power transformer.

3. Plug in the new rechargeable battery.

Installing an RJ-31X Jack

Install and wire the RJ-31 X jack as shown in Figure 8.

TO PANEL

JACK LABELED

'TO LINE'

PREMISES PHONE JACK

GREEN

RED

GREEN

TELCO

PROTECTOR

BLOCK

EXISTING

PHONE

LINE

PHONE CORD

RED

BRN

GRN

BLACK

SPLICE

GREEN

DEALER

CABLE

BLACK

WHITE OR YELLOW

GRY

RED

WHITE OR YELLOW

8988G05B.DS4

R E C H A R G E A B L E B A T T E R Y

8 9 5 9 G 3 0 A . D S F

Figure 7. Rechargeable Battery Installation

Connecting the Phone Line to the Control Panel

If the syste m will be monitored by a central monitoring station, you must in stall an RJ-31X jack betwe en the telephone company (TELCO) block and the Control Panel. The jack must be located within 5 feet of the Control Panel.

Figure 8. RJ-31X Wiring Diagram

Connecting the Phone Line to the Control Panel

1. Plug one end of the phone cord (included with the Control Panel) into the RJ-31X jack.

2. Plug the other end of the phone cord into the Control Panel phone jack labeled TO LINE.

3. When looking at the back of the Control Panel, the top block is used to connect the phone to the Control Panel, and is labeled TO PHONE, the bottom block is used to connect the Control Panel to the wall phone jack, and is labeled TO LINE.

Page 26

Installation Instructions Document No. 466-1574.

Programming Overview

These instructions t ell you how t o set up for programming and to put the Control Panel in program mode.

1. Arrange the sensors, modules, Control Panel, and user controls on a table.

2. Open the Control Panel cover.

3. Enter Utilit y Access Code 1 (default is 4321) using red numbered keys.

Note:The default for utility a ccess codes 1 and 2 is 4321.

Note:The default master access code is 1234.

You are now in program mode. Programming is easy if y ou understand the flow from

left to right when using the programming buttons. Follow the programming arrows or use the flow diagrams to the right of the programming buttons. The Control Panel will voice prompt you through programming.

To get you started:

1. Press Add or Delete from the Start Menu.

2. Press Option #, Sensor/Remote, Access Code or Light Control from the Main Menu.

The system response a t thi s poi nt de pends u pon what button you just pressed. Fol low the voice prompts and programming arrows to continue.

Program the Control Panel in this order:

1. Sensors

2. House Code

3. Light & Appliance Control

• Entry/Exit activated lights

• Sensor activated lights

• Time activated lights

4. Options

5. Access Codes

8988G37D.DSF

8988G38A.DSF

Page 27

Installat i on Instructions Document No. 466- 1574

Programming Sensors

These instructions show you how to p rogram sensors, touchpads and other system devices into the Control Panel.

Program sensors and de vices bef ore you i nstall th em. The Control Panel recognizes a sensor when you press the sensor’s program button or tamper switch.

Note: The hardwire inputs must have sirens, hardwire sensors, or 47k Ohm resistors connected between the positive and negative terminals before learning in a sensor. If one of these connections is not made, the panel will learn in a hardwire zone. See the section “Wiring the Control Panel” on page 21.

Note: If you are installing a sensor used with a gun case, jewelry box, or similar usage, and the sensor is active in level one, you must go into program mode to avoid putting the Control Panel into alarm when the sensor and the magnet are separated.

Table 19 describes the programming button location for each device.

Table 19 Device Programming

Device To Program

The Control Panel uses an ascending numbering sequence (beginning with 1) when adding (learning) sensors. You may override the system suggested sensor number by using the red numbered keys.

Use Table 1 on page 5, which was fi lled out during the system planning, to help program sensors.

To add a hardwire or RF sensor, SWS, or remote control:

Note: Do not program the SWS into the control panel until the house code has been programmed. See “Programming the House Code and Unit Numbers*” on page 26.

1. Press Add from the Start menu.

2. Press the Sensor/Remote button from the Main

menu until you hear the room name or item you want to add. The order of names the Control Panel uses are: keychain remote, touchpad remote, front door, back door, garage door, bedroom, guest room, child’s room, utility room, living room, dining room, bathroom, la und ry room, kitchen, office, den, garage, special chime, basement, upstairs, downstairs, hallway, medicine cabinet, closet, attic. Each name may be used more than once.

Door/Window Sensor Press butto n on top of sensor

(cover removed)

Motion Sensor Press button on back of sensor

(mounting plate removed) KeyChain Touchpad Press lock & Unlock butt ons Remote Handheld Touch-

pad and Touchtalk 2-Way RF Touchpad*

Hardwir e Se nsors Separat e se n sor from magn et SWS* Plug in the module CO Alarm Plug in the modules and within

Freeze & Water Press the button on top of the

Note: When installing crystal sensors, use the installation instructions included in their packing boxes. The appendix at the back of this document has instructions for the SAW sensors.

Press the EMERGENCY but-

tons (to be used for non-medi-

cal emergencies)

30 seconds press the button for

6 beeps

sensor (cover removed) until

the control panel confirms the

programming. If the button is

not held down long enough,

SYSTEM STATUS will report

the sensor is open.

* = Not Available with Basic Model

Note: When adding sensors, if you wish to use a more descriptive location you may press the option button to use the compass directions (north, north east, east, south east, south, south west, west, north west). This is especially usefule when installing a system with a Touchtalk 2-Way RF Touchpad. The touchpad will not announce the sensor numbers when the system status is pressed. Instead of

Sensor 1 Bedroom Open you will hear Bedroom Sensor Open. For example, if you have two bedrooms, name the

sensors West Bedroom and East Bedroom. When status is

pressed on the touchpad you will hear West Be droom Sen- sor Open.

3. Press DONE when you hear the name you wish

to add.

4. Enter the 2 digit sensor type using Table 1 on

page 5, with the red numbered keys.

Note: If you wish to use a sensor number other than the next available, enter a 2 digit sensor number with the red numbered keys immediately after entering the sensor type.

5. Press the sensor’s program button or tamper

button. Open the switch of hardwired sensors. See Table 19, “Device Programming” for more information. The Control Panel verba lly confirms your programming.

Page 28

Installation Instructions Document No. 466-1574.

To delete sensors:

1. Press Delete from the Start menu.

2. Press Sensor/Remote from the Main menu until

you hear the name you want to delete.

3. Press DONE. The system confirms the item you

removed.

Programming the House Code and Unit Numbers*

Lamp Modules, Appliance Modules, Remote Sirens, and the SWS use the existing electrical wiring in the home to receive signals fr om the Control Panel. Since there are no direct wire connections required, any number of modules can be plugged into availabl e outlets and insta lled in the system. All Lamp Modules and Appliance Modules have a common house code that allows modules to be identified by eight dif ferent control addresses.

The house code allows adjacent homes that have a common power source to co-exist. The available house code choices are from A to O.

Programming Light and Appliance Controls*

Use Table 6 on page 9, which was fi lled out during the system planning, to help program control modules.

To add an entry/exit activated light:

1. Press Add from the Start menu.

2. Press Light Control from the Main menu.

3. Press Unit # until you hear the number you chos e

on the module.

4. Press Entry/Exit Delay from the Control men u.

The Control Panel confirms your programming.

To add a sensor-activated light:

1. Press Add from the Start menu

2. Press Light Control from the Main menu.

3. Press Unit # until you hear the number you chos e

on the module.

4. Press Sensors from the Control menu until you

hear the sensor you want to control the light.

5. Press DONE. The Control Panel confirms your

programming.

To program the house code:

1. Press Add from the Start menu.

2. Press Light Control from the Main menu until

you hear the house code letter you want.

3. Press DONE.

4. Set the house code on each lamp and appli- ance module using a screwdriver.

5. Set house code on the remote siren to the next alphabetical letter greater than the house code.

All Lamp Modules with t he same house code will tur n on or flash as a group on ala rm or when opera ting the “Light” button on a KeyChain Touchpad. The units must be identified with a unique unit number, fr om 18, to individual ly operate lig hts and appli ances from a Remote Handheld Touchpad or to selectively program lights to go on during the entry/exi t delay, to be operated by a sensor or at scheduled times.

To assign a unit number:

1. See Table 6 on page 9 for your planning infor- mation.

2. Set the Unit number switch on each module.

Note: A KeyChain Touchpad can be programmed to a unit number. Press the star button to activate a light or open/ close a garage door using the Universal Module.

To add a time-activated li ght:

1. Press Add from the Start menu.

2. Press Light Control from the Main menu.

3. Press Unit # until you hear the unit number you

chose on the module.

4. Press Time from the Contr ol menu.

5. Press Hours and Minutes to set the begin ning of

the schedule.

6. Press DONE.

7. Press Hours and Minutes to set the end of the

schedule.

8. Press DONE. The system confirms your pro-

gramming.

To delete an Entry/Exit-activated light:

1. Press Delete from the Start menu.

2. Press Light Control from the Main menu.

3. Press Unit # until you hear the unit number you

want to delete.

4. Press Entry/Exit Delay. The system confirms

* = Not Available with Basic Model

Page 29

Installat i on Instructions Document No. 466- 1574

your programming.

To delete a sensor-activated light:

1. Press Delete from the Start menu.

2. Press Light Control from the Main menu.

3. Press Unit # until you hear the unit number you

want to delete.

4. Press Sensors from the control menu until you

hear the one you want to delete.

5. Press DONE. The system confirms your pro-

gramming.

To delete a time-activated light:

1. Press Delete from the Start menu.

2. Press Light Control from the Main menu.

3. Press Unit # until you hear the unit number you

want to delete.

4. Press Time from the control menu.

Programming Options

Use Table 18 on page 19, which was filled out during the system planning, to help program options.

There are two ways to enter options. They are as follows:

•Press Add and press the Option # button until

you hear the option to be changed.

or--

•Press Add and enter the option number you

want to program with the red numbered keys.

The following instructions use the second method.

2. Press Option # and 04, 05, or 06.

3. Enter a phone number with the red numbered keys. Press Test to enter a pause in the phone number.

Note: The phone number is automatically stored after you’ve pressed 22 digits. You will not have to press DONE to store the number. If the number is less than 22 digits, then DONE must be pressed.

To set syst em option 07:

1. Press Add from the Start menu.

2. Press Option # 07.

3. Enter the account number.

4. Press DONE.

To set syst em option 08:

1. Press Add from the Start menu.

2. Press Option # 08.

3. Press DONE.

To set syst em option 09:

1. Press Add from the Start menu.

2. Press Option # 09.

3. Enter the downloader code.

4. Press DONE.

To set syst em options 10 & 11:

1. Press Add from the Start menu.

2. Press Option # 10 or 11.

3. Enter the delay times in seconds (3 digits must be entered).

To set system options 12 & 13:

1. Press Add from the Start menu.

2. Press Option # and 12 or 13.

3. Enter phone mod number.

To set system options 01 and 02:

1. Press Add from the Start menu.

2. Press Option # and 01 or 02 with the red num-

bered keys.

3. Press DONE.

To set syst em option 03 :

1. Press Add from the Start menu.

2. Press Option # 03.

3. Press Hours and Minutes to set the time.

4. Press DONE.

To set system options 04, 05, and 06:

1. Press Add from the Start menu.

To set syst em option 14:

1. Press Add from the Start menu.

2. Press Option # 14.

3. Press DONE.

To set syst em option 15:

1. Press Add from the Start menu.

2. Press Option # 15.

3. Enter the no activity time out (2 digits must be entered).

To set syst em option 16:

1. Press Add from the Start menu.

2. Press Option # 16.

3. Enter the number of days between each auto

Page 30

Installation Instructions Document No. 466-1574.

phone test (3 digits must be entered).

To set syst em option 17 :

1. Press Add from the Start menu.

2. Press Option # 17.

3. Enter the dialer delay in seconds (3 digits must

be entered).

To set syst em option 18 :

1. Press Add from the Start menu.

2. Press Option # 18.

3. Enter the alarm cancel time in minutes (2 dig-

its must be entered).

To set syst em option 19 :

1. Press Add from the Start menu.

2. Press Option # 19.

3. Enter the supervisory time in hours (2 digits

must be entered).

To set system options 20 - 26, 28 - 30, and 32:

1. Press Add from the Start menu.

2. Press Option # XX.

3. Press DONE.

To set syst em option 27 :

1. Press Add from the Start menu.

2. Press Option # 27.

3. Enter the ring/hang/ring number.

3. Enter the minutes (2 digits must be entered).

To set syst em option 43:

1. Press Add from the Start menu.

2. Press Option # 43.

3. Enter a phone number with the red numbered keys. Press Test to enter a pause in the phone number.

Note: The phone number is automatically stored after you’ve pressed 22 digits. You will not have to press DONE to store the number. If the number is less than 22 digits, then DONE must be pressed.

To set syst em option 44:

1. Press Add from the Start menu.

2. Press Option # 44.

3. Enter phone mod number.

To set syst em option 45 - 53:

1. Press Add from the Start menu.

2. Press Option # XX.

3. Press DONE.

To delete options:

1. Press Delete from the Start menu.

2. Press Option from the Mai n menu until you hear the name you want to delete or use the red numbered keys to go directly to the option.

3. Press DONE. The system confirms the item you deleted.

To set syst em option 31 :

1. Press Add from the Start menu.

2. Press Option # 31.

3. Enter the day of week number.

To set system option 33, 38, 40-42:

1. Press Add from the Start menu.

2. Press Option # XX.

3. Press DONE.

To set system options 34-37:

1. Press Add from the Start menu.

2. Press Option # XX.

3. Press Hours and Minutes to set the time.

4. Press DONE.

To set syst em option 39 :

1. Press Add from the Start menu.

2. Press Option # 39.

Programming System Access Codes

Use Table 7 on page 10, which was filled out during the system planning, to program system Access Codes.

To add a code:

1. Press the Add button.

2. Press the Access Code button. Co ntinue p ressing the Access Code button until you hea r the acce ss code to be changed.

3. Press DONE.

4. Enter the new access code by using the red numbered keys.

The Control Panel says, code name is XXXX (the new 4 digit access code).

Page 31

Installat i on Instructions Document No. 466- 1574

To delete a code:

1. Press Delete from the Star t menu.

2. Press the Access Code but ton. Continue pre ssing

the Access Code button until you hear th e access code to be deleted.

3. Press DONE. The Control Panel says, code name is deleted.

Installing the System

Control Panel General Information

Do not install the Control Panel near a window or door where it can be reached easily by an intruder.

Control Panels s hould b e ins talled i n loc ation s wh ere they are most likely to be heard.

Metal objects, mirrors, and metallic wallpaper can block signals sen t by th e wirel ess s ensors . Make sur e there are no metal objects in the way when in stalling the system.

The system will prompt you through programming steps with beeps and voice messages. If you need more time before proceeding, simply close the Control Panel cover until you are ready to continue.

When the cover is closed, the Control Panel is in the operating mode. Each time you close the Control Panel cover, a series of beeps (from the control panel piezo, hardwire internal siren, SWS, and the X-10 powerhorn) will indicate the system status:

• One beep indicates th e system is disarmed

• Two beeps verify that Door/Window sensors are armed.

• Three beeps verify that Motion Sensors are armed.

• Four beeps verify that both Door/Window and Motion sensors are armed.

Table 20 Arming Levels

Arming

Level

0 Bypasses 24 hour intrusion sensors ( Master

Access Code Only)

Description of Level

Table 20 Arming Levels

Arming

Level

1 Disarm the system 2 Arm Doors and Windows 3 Arm Mot ions 4 Arm Doors, Windows, and Mo tions

The system cannot work wi thout powe r. If th e electr ical power fails and the Control Panel battery is weak or dead, the system will not work.

Description of Level

Control Panel Specifications

Power Requirements: 9 VAC, 700 mA Non-Chargeable Backup Battery: 9 VDC 1.2 AH

UltraLife Lithium. Th e battery will last 24 h ours with no AC if fully charged. Typical Life of 1 year.

Rechargeable Backup Batteries:

1. 7.2 VDC, 1 Ah 5/3 AAA Nickel Metal Hydride The battery will last 30 h ours with no AC

2. 7.2 VDC, 580 mAh AAA Nickel Metal Hydride The battery will last 16-18 hours with no AC

Radio Frequency: 319.5 MHz + or - 140 kHz Nominal Range: 500 feet, open-air receiving range Operating Temperature Range: 32°-122 ° F (0°-

50° C) Maximum Humidity: 85% relative humidity, non-

condensing Auxiliary Power Output: Regula ted & unr egulated,

fused 12 VDC at 250 mA (maximum)

Installation Guidelines

Use the following procedure to mount the Control Panel to the wall or wall studs, using the supplied mounting hardware and the panel mounting holes.

Material s Needed

•Pencil

• Hammer

Page 32

Installation Instructions Document No. 466-1574.

• Screwdriver

To mount the panel:

1. Choose a spot within a few feet of an electrical outlet (the outlet should not be controlled by a wall switch) and al so wit hin re ach of a t elephon e jack. The Control Panel can be placed on a desk, tabletop, or it can be wall mounted.

2. Open the Control Panel co ver and positi on on the wall.

3. Mark the screw hole locations with a pencil.

4. Start holes with the tip of the screwdriver or a nail.

5. Tap the wall anchors provided into the holes.

6. Insert the screws and partially tighten with the screwdriver.

7. Hang the Control Panel on the screws and tighten securely.

8. Remove the center screw from the outlet cover plate.

9. Position the transformer so that its screw hole is aligned with the screw hole on the outlet cover plate. Then plug the transformer into the outlet.

10. Replace the screw, and use it to secure the transformer to the outlet cover plate. Tighten th e screw firmly with your screwdriver.

Sensor Installation

Windows, and Motion Sensors when also entering the appropriate access code.

• SYSTEM STATUS-Press to determine system status and system time.

• CHIME Doors-Press to enable two beeps which will sound from the interior siren output, the panel siren, SWS, and the X-10 powerhorn siren (if set to unit numbe r 9) when a p rotecte d door or window , that i s pro grammed a s sens or typ e 10 or 13, is opened.

• CHIME Special Motion- Press to enable three beeps which will sound from the interior siren output, the panel siren, SWS, and the X-10 powerhorn siren (if set to unit number 9) when a Motion Sensor, that is programmed as sensor type 25, is activated. If there are no sensors learned as type 25, this f uncti on will n ot be available. The control panel will also announce whic h sensor was tripped if chime voice (option 41) is on.

• LIGHTS Time Activated-Press to enable system controlled lights to turn on/off at a scheduled time.

• LIGHTS Sensor Activated-Press to enable system controlled lights to turn on for 4 minutes when a specific sensor is tripped.

• EMERGENCY-Press and hold or press twice quickly to activate a non-medical emergency alarm.

Use the installation instructions included with eac h sensor or if installing SAW sensors use document 466-1622, Booklet of Installat ion Instr uct io ns, attached to the back of this manual, for SAW Sensors.

Testing the Control Panel

Test the Control Panel by pressing the buttons as described below:

• ARM Doors & Windows-The Control Panel arms Doors & Wi ndows. Press twice to eliminate the preprogrammed entry delay. The button will blink when N o Entry Delay is on.

• ARM Motion Sensors-The Control Panel will arm Motion Sensors. Press twice to turn Latchkey on. The button blinks when Latchkey is on.

• DISARM -The Control Panel will disarm Doors,

Testing the System

This section describes how to perform the following test procedures:

• Testing sensors

• Testing phone communication

• Testing central station communications

• Testing the X-10 Lamp Modules You should test the system after insta lling, after ser-

vicing, and after adding or remov ing devices fr om the system.

Testing Sensors

We recommend that you test the sensors after all pro-

Page 33

Installat i on Instructions Document No. 466- 1574

gramming is completed and whenever a sensor-related problem occurs.

Note: While the sensor test is a valuable installation and service tool, it only tests sensor operation for the current conditions. You should perform a sensor test after any change in environment, equipment, or programming.

1. Place all sensors in their secured (non-alarm) state.

2. Open the Control Panel cover.

3. Enter the appropriate access code.

4. Press Test.

The Control Panel responds with Sensor test, press

again to change or DONE to select.

5. Press DONE.

Note: If the primary or secondary phone number (option 4

or 5) has been programmed, after pressing Test a second time, the Control Panel announces Phone Test. The phone testing procedure will be discussed later in this manual. After pressing Test a third time, the Control Panel announces DL phone test.

The Control Panel wil l prompt you to trip ea ch sensor one at a time. You may follow the Control Panel’s voice prompting or test the sensors in any order.

Interior sirens and speaker s sound transmission beeps as each sensor is t ripped. Each beep repre sents one RF packet.

Use the following table to trip sensors.

Sensor Trippi ng Instruct ions :

Sensor Do This

Door/Window Open the secured door or win-

dow

Freeze Apply ice to the sensor. Do not

allow the sensor to get wet

Water Press a wet rag or wet finger

over both of the round, goldplated terminals on the underside of the sensor

Carbon Monoxide Alarm

Unplug the CO Alarm. Plug it back in, then press the TEST/ RESET button until the unit beeps 8 times

Sensor Tripping Instructions:

Sensor Do This

Rate-of-Rise Heat Detector

Shock Tap the glass twice, away from

Smoke Press and hold the test button

Panic Buttons Press and hold the appropriate

KeyChain Touchpad

Remote Handheld Touchpad and Touchtalk 2-Way RF Touchpad*

SWS* Unplug the SWS, plus the unit

Rub your hands together until warm, then place one hand on the detector for 30 seconds

the sensor. Wait at least 30 seconds before testing again

until the system sounds transmission beeps

panic button(s) for 3 seconds

Press and hold LOCK and UNLOCK simultaneously for 3 seconds

Press and hold the 2 EMERGENCY buttons simultaneously for 3 seconds

back in

6. Count the number of transmission beeps and

refer to Table 21 on page 32 for minimum requiremen ts. After the beeps, the Control Panel announces, Sensor Name i s ac ti vat ed, s ensor sta- tus is XX (XX = number of RF packets). The system will continue to prompt for sensors which have not yet been tested. When all sensors have been tested the Control Panel will announce, Sensor test complete, press DONE.

7. Press DONE. The system will respond, Sensor

Test OK.

8. If Cancel or DONE is pressed and the Control

Panel has not heard from all se nsors, the Control Panel will respond, Sensor test canceled or fail-

ure.

Note: If a sensor does not meet the minimum transmission beep requirements, refer to the If a Sensor Fails the Sensor Test section.

Glass Guard Tap the glass 3 or 4 inches from

the sensor

Motion Sensor Avoid the Motion Sensor’s view

for 5 minutes, then enter its view

* = Not Available with Basic Model

Page 34

Installation Instructions Document No. 466-1574.

Table 21 Minimum Transmission Beeps

Type of Sensor

Wireless Intrusion Sensors 7–8 beeps

Wireless Smoke & Heat Sensors 7–8 beeps

Wireless Environmental/Panic Buttons 7–8 beeps

Hardwire Loops 1

Emergency Buttons* 7-8 beeps

Number of

Beeps

* The Control Panel Emergency Button cannot be tested.

If a Sensor Fails the Sensor Test

If sirens do not beep when a sensor is tripped, use an ITI RF Sniffer ( 60-401) tes t tool to verify that the sensor is transmitti ng. Constant be eps from the RF Sni ffer indicate a runaway (faulty) sensor. Replace the sensor.

If possible, locate sensors within 100 feet o f the panel. While a transmitter may have a range of 500 feet or more out in the open, th e environment at the installation site can have a significant effect on transmitter range. Sometimes a change in sensor location can help overcome adverse wireless conditions.

To replac e a sensor:

1. Test a known good sensor at the same location.

2. If the tra nsmission beeps remain below the minimum level, avoid mounting a sensor at that location.

3. If the replacement sensor functions, contact ITI for repair or replacement of the problem sensor.

Testing Phone Communication

Perform a phone test to check the phone communication between the panel and the central station.

To perform a phone test/DL phone test:

1. Open the Control Panel cover.

2. Enter the appropriate access code .

3. Press Test twice.

4. Press DONE. The Control Panel responds with, Phone test is on. When the phone test is complete, the Control Panel will announce Phone Test is OK within 3 minutes. The Control Panel will say Phone tes t is on thre e times if you have a pager. Your pager will display 101 101 if the phone test to the page r was suc ces sful. If the test is unsuccessful, the SYSTEM STATUS button will light and the Control Panel will say Phone communication failure within 10 minutes.

To improve sensor communication, you can

• reposition the sensor

• relocate the sensor

• if necessary, replace the sensor

To reposition a sensor:

1. Rotate the sensor and test for improved sensor communication at 90 and 180 degrees from the original position.

2. If poor communication persists, relocate the sensor as described as follows.

To relocate a sensor:

1. Test the sensor a few inches from the original position.

2. Increase the distance from the original position and retest until an acceptable location is found.

3. Mount the sensor in the new location.

4. If no location is acceptable, replace the sensor.

If the panel announces Phon e communication f ailure, proceed to the followin g instruction s.

If the phone test fails:

1. Check that the panel is connected to the phone jack.

2. Check the phone number programmed into the panel.

3. Perform the phone test again.

4. If the phone test fails again, che ck the phone con nection wiring.

Testing Central Station Communication

After performing sensor and phone tests, check that the system is reporti ng alarms succ essfully to th e central station.

Page 35

To test communication with the central station:

1. Call the central station and tell the operator that you will be testing the system.

2. Arm the system.

3. T est ea ch of the wi reless p anic butt ons and tri p at least one sensor of each type—fire, intrusion, etc.—to verify that the appropriate alarms are working cor r ectly.

4. When you finish testing the system, call the central station to verify that the alarms were received.

Installat i on Instructions Document No. 466- 1574

Table 22 Alarm Siren and X-10 Light

Information

Fire Intrusion Emergency

X-10 Lights Steady Flashing Steady X-10 Siren Steady Steady Alarm beeps Interior & Panel

Siren Exterior Siren Temporal 3 Steady

Temporal 3 Steady Fast on/off

Testing the X-10 Lamp Modules*

Use Table 6 on page 9 to determine t he full extent of module testing to be accomplished.

To test the system controlled lamp modules:

1. Press the LIGHT button on the KeyChain T ouchpad repeatedly to turn all lights on and off. The Control Panel responds with Lights on/off.

2. Press the Lights On button and the unit # of the lamp module using the numeric buttons on the Remote Handheld Touchpad to test individual lamp modules, the Control Panel will res pond with Lights # on/off.

Siren and X-10 Lamp Module Functions*

SWS Temporal 3 Steady Fast on/off

Panel Tamper

If the system is armed and the cover is opened an intrustion alarm will sound and the system status will say System Access Alarm when the button is pressed.

All sirens will time-out in the programmed siren timeout (1 - 254 minutes). Sire n priority is as foll ows: fire, intrusion, then emergency. If an alarm of greater priority occurs during an alarm of lower priority, the higher priority alar m sirens sound . Th e X-10 must be set to unit #9 to hear emergency alarm beeps. Fire alarms will sound a temporal 3 pattern. Temporal 3 is

0.5 seconds on, 0.5 seconds off for 3 beeps then 1.5

seconds off.

* = Not Available with Basic Model

Page 36

Installation Instructions Document No. 466-1574.

Troubleshooting

Use the following table to aid you with troubleshooting problems during installation.

Table 23 Troubleshooting Guide

Problem Solution

SYSTEM ST ATUS

How to clear SYSTEM STATUS (Alarm Memory) From a disarmed state press SYSTEM STATUS twice, listen to the

status message, then press DISARM.

SYSTEM STATUS says Module 1 failure or Module 2

failure.

SYSTEM STATUS says Low Battery. UltraLife lithium battery

SYSTEM STATUS says Option 50 Detected. Option 50 is RF jam detect. The control panel has detected RF inter-

SYSTEM STATUS says that a sensor is open. See Sensors section below. SYSTEM STATUS says System time is not set. Set the system time.

Control Panel

The system says Function not available when Chime Doors is pressed.

The system says Function not available when Chime Special Motion is pressed.*

The system says Function not available when LIGHTS Time Activated is pressed.*

• Turn option 53 off if a hardwire siren or sensor is not connected.

• Check for the correct EOL resistor at Hardwire inputs 1 and 2. See “Connecting Hardwire Interior Sire ns” on page 21.

• Do a sensor test then check SYSTEM STATUS again. If the battery is still low, replace the battery.

Rechargeable Battery

• If the control panel has just been plugged in, the control panel will indicate a low battery unti l the battery is fu lly charg ed (9-12 hours). Make sure to turn option 49 on.

• If the control panel has been powered for more than 12 hours, make sure option 49 is on.

ference.

No sensors are progra mmed using sensor type 10 or 13.

No sensors are programmed using sensor type 25

No time activated lights have been programmed.

The system says Function not available when LIGHTS Sensor Activated is pres s ed.*

The system says Invalid. Sensor already programmed as Sensor Name.

Options (Pr o gr am m able by the homeowner )

The Control Panel does not beep. Program option 1 to be on. Latchkey does not function. • Latchkey time (option 3) is not set. Set Latchkey time.

Sensors

A sensor does not work.

No sensor activated lights have been programmed.

This sensor is already programmed. Delete sensor if not correctly programmed.

• Latchkey is not enabled. Enable Latchkey by pressing ARM Motion Sensors tw ice.

• The phone number is not programmed properly. Reprogram the phone number. (option 43)

• System Time is not set. Set system time.

• Make sure the battery is fresh and installed correctly.

• Check for interference from metal objects. Move or rotate the sensor.

• Move the sensor to a new location.

* = Not Available with Basic Model

Page 37

Installat i on Instructions Document No. 466- 1574

Table 23 Troubleshooting Guide

Problem Solution

Door or window is closed, but the Control Panel voice says it is open.

Motion sensors go off continuously. Be sure the sensor is mo unted o n a solid surfa ce and th e viewin g fiel d

Motion sensor does not respond to motion. • Make sure the battery is fresh and installed correctly. Wait 2

X-10 Modules*

All Lamp Modules or Siren not working.*

One Lamp Module or Siren is not working.* • Unplug nearby equipment which may be causing interference

• Be certain the arrow on the magnet and the guide line on the transmitter are aligned and are within 1/4’ of each other.

• The sensor tamper switch may be open if it is a crystal sensor.

is free from sources of changing temp erature.

minutes after installing a new battery to test the sensor.

• Adjust the sensor mounting.

• Leave the area for 3 minutes, then retest.

• The environment is too hot or too cold. Outdoor sensors will operate between 32° and 120°F.

• Dirt or dust may be c ausing the probl em. Wipe the sens or wit h a clean, damp cloth.

• Be sure the Control Panel tran sformer is plu gged direc tly into an outlet and that the outlet is not controlled by a wall switch.

• Pos s ib l y a ba d tr a ns former .

• House code was programmed incorrectl y.

(light dimmer switches, televisions, appliances with olde r motors).

• Check that the switch on the lamp or appliance is turned on and remains on.

• Make sure the lamp has a working bulb.

• Make sure the lamp or appliance is plugged into the Lamp/ Appliance Module, the Module is plugged into the outlet and the outlet is not controlled by a wall switch.

• Make sure the House and Unit Codes are correct.

• Move the Mod u le to a different outlet that is on the same phase (branch) of the household electrical circuit as the Control Panel.

Time activated or sensor activated light not working.* • Make sure you have programmed the light to be activated by a

timer or sensor.

• Make sure the system clock is set.

• Make sure these functions have been enabled by pressing the LIGHTS Time Activated/Sensor Activated on the Control Panel. They are enabled if the button is lit.

* = Not Available with Basic Model

Page 38

Installation Instructions Document No. 466-1574.

Typical Backup Battery Life of the 9 Volt UltraLife

The following table and chart demonstrate backup battery life over time if the battery is tested every 4 hours (option 50 is off).

Table 24 Typical Backup Battery Life

Cycle Over Time

Months in Use

0 30.159 1 27.861 2 25.562 3 23.264 4 20.966 5 18.668 6 16.370 7 14.072

811.774

99.475 10 7.177 11 4.879

Estimated Hours of

Backup Power

12 2.581 13 0.283

Typical Backup Battery Life Cycle Over Time

Estimated Hours of Backup Power

| |

1 2 3 4 5 6 7 8 9 10 11 12 13

| |

| | | | | | | |

Months in Use

1061G50A.DS

Page 39

Installat i on Instructions Document No. 466- 1574

FCC Notices

FCC Part 15 Information to the User

Changes or modification s not e xpre ssly approved by GE Interlogix can void the user’s authority to operate the equipment.

FCC Part 15 Class B

This equipment has been tested a nd found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasona ble prot ection against interference in a reside nti a l in sta ll ation.

This equipment generates, uses, and can radi ate radio frequency energy and, if no t i nsta ll ed and used in accordanc e with the instructions, may cause harmful interference to radio comm unications. However, there is no guarantee tha t in te rfe rence will not occur in a particular installation.

If this equipment does cause harm ful interference to radio or television reception, which can be det erm i ned by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the affecte d equipment and the panel receiver to se parate outlets, on diff erent branch circuits.

• Consult the deal er or an experienced radio/TV technici an for help. FCC ID: B4Z-787E-SIMON

ACTA Part 68

This equipment co m pli es with Part 68 of the FCC Rules. Lo cated on this equipment is a label that contains, among other information, the FCC registration number and the ringer equiv al en ce number (REN) for this equipment . If re quested, this information must be pro vided to the telephone co mpany.

FCC Part 68 Registration No. B4ZUSA-27621-AL-E REN: 0.2B The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result

in devices not ringing in response to an in com i ng call. In most areas, the sum of all device RE N s should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has th e format US:AAAEQ##TXXXX. The digits repr ese nted by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earl ie r products, the REN is separately shown on the label.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular jack that is also compliant. See the Installation Instructions for details.

Alarm dialing equipment must be able to seize the tele pho ne line and place a ca ll in an emerge nc y situation. It must be able to do this even if other equipment (telephone, ans w er ing system, computer mod em, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installe d RJ31X jack that is el ectric ally in series and ahea d of all ot her equip ment attached to the same tel ephon e line. Proper installation is depicted in the following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an RJ31X jack and alarm dialing equipment for you.

C u s t o m e r P r e m i s e s E q u i p m e n t a n d W i r i n g

N e t w o r k S e r v i c e P r o v i d e r ' s F a c i l i t i e s

T e l e p h o n e L i n e

N e t w o r k D e m a r c a t i o n P o i n t

T e l e p h o n e

R J 3 1 X

J a c k

If this equipment causes harm to the te lephone network, the telephone company may temporar ily disc onnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be given advance notice in order to maintain uninterrupted service.

If you experience trouble w i th this equipment, please cont act the company that install ed the equipment for service and/or repair information. T he t el ephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipm ent is not malfunctioning.

This equipment may not be used on coin service provided by the te le phone company. Connection to party lines is subject to stat e tariffs.

U n u s e d

R J - 1 1 J a c k

A n s w e r i n g S y s t e m

A l a r m D i a l i n g E q u i p m e n t

F a x M a c h i n e

T e l e p h o n e

C o m p u t e r

U n u s e d R J - 1 1 J a c k

T e l e p h o n e

Page 40

Installation Instructions Document No. 466-1574

Canada Notice

The Canadian Department o f Co mmunicatio n s label identifies certified e q u ipment. This certification means that the equipment me ets certain te lecommunications network protecti ve, operational, and safety requirements. The department does not guar ant ee the equipment will operate to the user ’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installe d usi ng a n acceptable method of connec ti on. In some cases, the company’s inside wiring associated wit h a single-line individual service may be extended by means of a certified conne ctor assembly (telephone extension cord). The custo me r should be aware that compliance with the above conditions may not pr event degradation of service in som e si tuations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or al teration s made by the user to this equipment, or equipment malf unctions, may give the telecommunic ations company cause to reques t th e user to disconnect the equipment.

For your protection, make sure that the electrical ground c onnections of the power utility, telephone lines, and internal metallic wate r pipe system, if pres ent, are connected together

Do not attempt to make connections yourself. Contact the appro priate electrician or elec-

Caution

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number: .1 The term “IC:” before the certification/registration number only signifies that the Industry Cana da technical specifications were met. IC: 867A 787SIMON

“AVIS: - L ´étiquette du ministère des Communications du Canada identifie le ma té rie l hom ologué. Cette étiquette certi fie que le matériel est conforme a certaines normes de protection, d ´ exploitation et de sécurité des réseaux de tél écommunications. Le ministère n ´ assure to ute fois pas que le matériel fonctionnera a la sati s f action de l ´ util is ateur.

Av an t d ´ installer ce matériel, l ´ utilisateur d o it s ´ assurer qu´ il est permis de le raccorder a ux in stallations de l ´ enterprise locale de télécommunication. Le matériel doi t également etre in s tallé en suivant u n e méthod acceptée d e raccordement . D an s certains cas, les fils intérieur s d e l´ enterprise utilisés pour un service individuel a ligne unique peuvent etre prolongés au moye n d´ un dispositif homologué de raccordement (cordon prolongat eur tél é phonique interne). L ´ abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci-dessus n ´ empechent pas le dégradation du service dans certaines situations. Actu el lement, les enterp r ises de télécommunication ne permett en t pas que l ´ on ra ccorde leur matéri el a des jacks d ´ abonné, sauf dans les cas précis prévus pas les tarrifs particuliers de ces enterprises.

Les réparations de matérie l ho mologué doivent etre effectuées pa s un centre d ´ entretien canadien aut orisé désigné par le fournisseur. La compagne de télécommunications peut dema nder a l ´ utilisateur de débrancher un appareil a la suite de réparations ou de modificati ons effectuées par l ´ utilisateur ou a cause de mauvais fonctionnement.

Pour sa propre protection, l ´ utilisat e ur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphonique s et des canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations électriques, ou a electricien, selon le cas”.

Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, doit etre incluse dans l ´ information qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suiva nt :

“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etr e racco rd ée a un circuit téléphonique bouclé utilisé par ce dispositif. La te rminaison du circuit bouclé peu t et re constituée de n ´ import somm e de s ind ic es de charge de l ´ ensemble des dispositifs ne dépasse pas 100.”

L ´ Indice de charge de cet produi t est ____________.

tric inspections authroity.

Page 41

Installat i on Instructions Document No. 466- 1574

Numerics 24 Hour Battery Test 22 2-Way Voice 17 2-way voice, on-board 4 300 Baud Central Station Communications 17, 22

319.5 Sensors 4 A AC Power Failure 16 AC Power Failure Report 21 Access Code 12 Access Code Programming 30 Access Code, Master 12 access code, master default 26 Access Code, Panic Code 12 Access Code, Utility 12 access codes, utility defaults 26 Account Number 13, 21 activation method 10 add hardwire/RF sensor, SWS, or remote control 27 alarm 35 Alarm Cancel 15 Alarm Cancel Report 21 appliance module 10 Appliance Modules 4 Arm Doors & Windows 9, 32 Arm Doors/Windows 16 Arm Doors/Windows & Motion Sensors 9 Arm Doors/Windows and Motion Sensors 16 ARM Doors/Windows with No Entry Delay 16 Arm Doors/Windows with No Entry Delay and Motion Sensors with Latchkey 16 Arm Motion Sensors 9, 16, 32 Arm Motion Sensors with Latchkey 16 arming levels 9 Audio Verification 16, 22 Audio Verification Mode 22 Audio Verification Module 6 Auto Arm 18, 22 Auto Phone Test 15, 21 Auxiliary Power Output 31 AVM 4, 6 AVM Fire Shutdown 19 AVM Mode 19 B Backup Battery Control Panel 31 Backup Battery, Connecting 24, 25 Backup Battery, Lithium 3

Battery Pack, Nickel Metal Hydride 3 battery test 24 C Carbon Monoxide (CO) Alarm 4, 6 CHIME Doors 18, 32 CHIME Special Motion 18, 32 Chime Voice 18, 22 Closing Reports 15, 21 CO Alarm 6 CO Alarm Sensor Type 8 Control Panel 4 Control Panel Alarms 16 Control Panel beeps 31 Control Panel Specifications 31 Control Panel, Wiring 23 CPU Low Battery 16 CPU Low Battery Report 21 CS-5000 Receiver 5 D Day of Week 17, 22 Delays 9 delete options 30 delete sensors 28 Dialer Delay 15, 21 disarm 9, 16, 32 DL Code (Downloader Code) 14 Door Window Sensor program button 27 Door/Window Sensor 3, 4, 5 Downloader Code 21 Downloader Phone Number 13, 21 DTMF 21 DTMF Dialing 14 E EMERGENCY 32 EMERGENCY buttons 27 Emergency Planning Floor Plan 6 Entry Delay 14, 21 Entry/Exit activated light 28 Entry/Exit-activated light 28 Exit Delay 14, 21 Exterior Door 8 F Factory Defaults, reset memory to 23 Fail to Close 17, 22 Fail to Communicate 16, 21 Fail to Open 17, 22 Fire Shutdown - AVM 19, 22 Floor Plan, Emergency 6 Follower Delay 9

Page 42

Installation Instructions Document No. 466-1574.

Force Arm 15 Forced Armed Report 21 Freeze Sensor 4, 8 G Garage Door Modules 4 H Hardwire Exterior Siren, Connecting 23 Hardwire Interior Sirens, Connecting 23 Hardwire Sensors program buttons 27 Hardwire Sensors, Connecting 23 High Level Status 22 HomeLink Transceiver 6 House Code 10 House Code and Unit Number programming 28 house code choices 28 I improve sensor communication 34 Indoor Motion Sensor 5, 8 Indoor/Outdoor Motion Sensor 4 Installation Guidelines 31 Installing the Control Panel 31 Instant Delay 9 Interior Door 8 Interrogator AVM 4 Interrogator® 200 Audio Verification Module (AVM) 6 ITI CS-5000 Receiver 5 ITI HomeLink Transceiver (IHT) 6 ITI ToolBox 5 K KeyChain Touchpad 3, 4, 5, 8 KeyChain Touchpad program buttons 27 KeyChain Touchpad programmed to a unit number 28 L Lamp Modules 4 Lamp Modules house code 28 Latchkey 13, 21 LD105 Siren 23 learning sensors 27 LIGHTS Time or Sensor Activated 32 Lock & Unlock buttons 27 low battery 24 M Manual Phone Test 15, 21 Maximum Humidity 31 Motion Activated Light Lock-Out Start Time 17 Motion Activated Light Lock-Out Stop Time 18 Motion Sensor Program Buttons 27

Motion Sensor, Indoor 5 Motion Sensor, Indoor/Outdoor 4 Motion Sensor, Outdoor 5 mount the panel 32 N No Activity 15 No Activity Report 21 No Delay from KeyChain Touchpad 16, 22 Nominal Range 31 Non-rechargeable Battery, installation 24 Normal Battery Use 38 O on-board 2-way voice 4 Opening Reports 15, 21 Operating Temperature Range 31 Option 01 Panel Piezo Beeps 12 Option 02 Panel Voice 12, 13 Option 03 Latchkey 13 Option 04 Primary Phone Number 13 Option 05 Secondary Phone Number 13 Option 06 Downloader Phone Number 13 Option 07 Account Number 13 Option 08 Phone Lock 13 Option 09 DL Code (Downloader Code) 14 Option 10 Entry Delay 14 Option 11 Exit Delay 14 Option 12 Phone Mod 1 14 Option 13 Phone Mod 2 14 Option 14 DTMF Dialing 14 Option 15 No Activity 15 Option 16 Auto Phone Test 15 Option 17 Dialer Delay 15 Option 18 Alarm Cancel 15 Option 19 Supervisory Time (SUPSYNC) 15 Option 20 Manual Phone Test 15 Option 21 Opening Reports 15 Option 22 Closing Reports 15 Option 23 Force Armed 15 Option 24 AC Power Failure 16 Option 25 CPU Low Battery 16 Option 26 Fail to Communicate 16 Option 27 Ring/Hang/Ring 16 Option 28 No Delay from KeyChain Touchpad 16 Option 29 Control Panel Alarms 16 Option 30 Panic Alarms 17 Option 31 Day of Week 17 Option 32 300 Baud 17 Option 33 2-Way Voice 17

Page 43

Installat i on Instructions Document No. 466- 1574

Option 34 Fail to Open 17 Option 35 Fail to Close 17 Option 36 Motion Activated Light Lock-Out Start Time 17 Option 37 Motion Activated Light Lock-Out Stop Time 18 Option 38 Auto Arm 18 Option 39 Siren Time Out 18 Option 40 Trouble Beeps 18 Option 41 Chime Voice 18 Option 42 Speaker Level 18 Option 43 Pager Phone Number 19 Option 44 Pager Phone Mod 3 19 Option 45 Sensor Alarm Restoral 19 Option 46 Fire Shutdown - AVM 19 Option 47 AVM Mode 19 Option 48 Panic Talk 19 Option 49 Rechargeable Battery 19 Option 50 RF Jam Detect 19, 20 Options Programming 29 Options, System 12 Outdoor Motion Sensor 4, 5, 8 P Pager Phone Mod 3 19, 22 Pager Phone Number 19, 22 Panel Piezo Alarm 22 Panel Piezo Beeps 12, 21 Panel Piezo Beeps Table 13 Panel Tamper 35 Panel Voice 12, 13, 21 Panic Alarms 17, 22 Panic Talk 19 Panic Talk - Audio Verification Mode 22 Phone Button(s) 17 Phone Line Connecting 25 Phone Line to the Control Panel, Connecting 25 Phone Lock 13, 21 Phone Mod 1 14, 21 Phone Mod 2 14, 21 Planning Control Locations 10 Planning Module Control 10 Planning System Access Codes 12 Power Requirements Control Panel 31 Power Transformer 3 Power Transformer, Connecting 24 Powerhorn Siren house code 10 Primary Phone Number 13, 21 Program Buttons 27 program mode 26

program the house code 28 Programming Access Codes 30 Programming Light/ Appliance Controls 28 Programming Options 29 Programming Overview 26 Programming the House Code and Unit Numbers 28 R Radio Frequency Control Panel 31 range 34 Receiver, CS-5000 5 Rechargeable Battery 19, 22, 31 Rechargeable Battery, Connecting 25 Recommended Sensor Types 8 relocate a sensor 34 Remote Access 16 Remote Handheld Touchpad 4, 5, 8 Remote Handheld Touchpad program buttons 27 remote siren house code 28 Remote Siren house code, unit number 10 Remote Siren, Powerhorn 4 replace a sensor 34 reposition a sensor 34 Reset Memory to the Factory Defaults 23 RF Jam Detect 19, 20, 22 RF Sniffer 34 Ring/Hang/Ring 16, 21 RJ-31X Jack, Installing 25 S Secondary Phone Number 13, 21 Sensor Activated Light Lockout Start Time 22 Sensor Activated Light Lockout Stop Time 22 Sensor Alarm Restoral 19, 22 Sensor Fails Sensor Test 34 sensor learning 27 Sensor Tripping Instructions 33 Sensor Type Characteristics 9 sensor, 24-hour 34 sensor, deleting 28 sensor, hardwire loop 34 Sensor/Device Location Planning Table 7 sensor-activated light 28, 29 Siren and X-10 Lamp Module Functions 35 Siren Time Out 18, 22 Siren, LD105 23 Smoke Sensor 3, 5, 8 Smoke Sensor, Wireless 3 Speaker Level 18, 22 Special Installation Requirements 3

Page 44

Installation Instructions Document No. 466-1574.

Specifications Control Panel 31 Standard Delay 9 Status, System 16 Subdisarm 9 subdisarm 12 Supervised Wireless Siren (SWS) 6 Supervisory Time (SUPSYNC) 15, 21 SUPSYNC 3 SWS 4, 6 SWS programming 27 SWS Sensor Type 8 SWS, Supervised Wireless Siren 6 System Options 12 System Status 16, 24, 32 System, Basic 3 T Table Access Codes 12 Table Alarm Siren and X-10 Light Information 35 Table Arming Levels 31 Table Audio Verification Set 17 Table Day of Week by Number 17 Table Device Programming 27 Table Home Control Planning 11 Table House Code Assignments 11 Table Minimum Transmission Beeps 34 Table Opening/Closing Reports User Codes 15 Table Pager Phone Mod Format 19 Table Pager Reporting Message 19 Table Panel Piezo Beeps 13 Table Phone Commands for Remote Access 16 Table Phone Mod 1 14 Table Phone Mod 2 14 Table Programmable Options 21 Table Recommended Sensor Types 8 Table Ring/Hang/Ring Program Numbers 16 Table Sensor Tripping Instructions 33 Table Sensor Type Characteristic 9 Table Sensor/Device Location Planning 7 Table Troubleshooting Guide 36 Table Unit Number Assignments 11 Table User Codes for OpeningClosing Reports 15 Tamper alarm 35 tamper button 27 Testing Phone Communication 34 Testing the System 32 Testing the X-10 Lamp Modules 35 time-activated light 28, 29

Toggle Lights 16 ToolBox, ITI 5 Touchpad, 2-Way RF Touchtalk 4 Touchpad, KeyChain 4, 5 Touchpad, Remote Handheld 4, 5 Touchpad, Touchtalk 2-Way RF 5 Touchtalk 2-Way RF Touchpad 4, 5, 8 Touchtalk 2-Way RF Touchpad program buttons 27 Trouble Beeps 22 Trouble beeps 18 U UL 1023 3 ULC-S545-M89 3 UL-Listed Installation Requirements 3 Unit Number 10 Universal Module 10 Universal/Garage Door Modules 4 Universal/Garage Door Opener Module, Connecting 24 User Codes for Opening/Closing Reports Table 15 W Wall Switch Modules 4 Water Sensor 4, 8 Window Sensor 8 Wiring the Control Panel 23 X X-10 Appliance Module 4 X-10 Lamp Module and Siren Functions 35 X-10 Lamp Modules 4 X-10 Powerhorn/Remote Siren Modules 4 X-10 Universal/Garage Door Modules 4 X-10 Wall Switch Modules 4

Page 45

Installat i on Instructions Document No. 466- 1574

Page 46

Installat i on Instructions Document No. 466- 1574

Page 47

Installat i on Instructions Document No. 466- 1574

Page 48

Lights off

SYSTEM

STATUS

9 – 0

on special lights

Toggle lights

Lights on

SYSTEM

STATUS

7 – 8

Set lights to time activated

Set lights to sensor activated

Open a garage door or turn

Time

Activated

LIGHTS

Sensor

Activated

Set Special Motion Chime

LIGHTS

CHIME

Special

Motion

DOORS

Set doors to Chime

CHIME

Send an alarm to the

Central Monitoring Station

Check the system status

EMERGENCY

SYSTEM

STATUS

Press & hold

for 3 seconds

Press Twice

Activate the Latchkey feature

Disarm the system

Subdisarm the system

Master Code

Sensors

Motion

DISARM

+ Access Code

Press Twice

ARM

Arm the system

– Motion Sensors

Arm the system

– Doors/Windows & Motion Sensors

Activate No Entry Delay

Windows

Doors &

ARM

Sensors

Motion

ARM

Sensors

Motion

ARM

Windows

Doors &

Press Twice

Arm the system

– Doors & Windows

How to . . .

Windows

Doors &

ARM

CONTROL PANEL

Press Twice

Press & hold

Press + Master Code + 0

Master Code

SYSTEM

STATUS

Press both EMERGENCY buttons.

+ Unit #

Press & hold for 3 seconds.

Press Once

DISARM

+ Access Code

Sensors

Motion

ARM

Press Twice

Windows

Doors &

ARM

Press Twice

Windows

Doors &

ARM

Sensors

Motion

ARM

Sensors

Motion

ARM

Windows

Doors &

ARM

Touchtalk 2-Way RF

TOUCHPAD

Quick Reference Table

REMOTE HANDHELD &

KEYCHAIN TOUCHPAD

Press & hold

Press + Master Code + + 1

for 3 seconds

Press + Master Code + 1

Press 3 times

Press + Master Code + 3 + 3

Press once if

programmed

Press + Master Code + 2 + 2

Press twice

Press + Master Code + 2 + 3

Press + Master Code + 3

Press + Master Code + 2

REMOTE PHONE CONTROL

466-1574