Simfer SYD 150 MD DC, SYD 210 MD DC, SYD 410 MD DC, SYD 650 MD DC, SYD 550 MD DC User Manual
...Page 1
CONSERVATORS
Models
SYD 150 MD DC
SYD 210 MD DC
SYD 310 MD DC
SYD 410 MD DC
SYD 550 MD DC
SYD 650 MD DC
USER MANUAL
1
Page 2
Dear Customer,
Thank you for choosing Simfer products. We aim to allow you to optimally and eciently use this environment-friendly product produced
in our modern facilities under precise conditions with respect to sense
of quality in total.
We advise you to read this user manual thoroughly before using the
freezer and keep it permanently so that the features of the Simfer
freezer you have purchased will stay the same as the rst day for a
long time and serve in an optimum ecient way.
NOTE:
This User Manual is prepared for multiple models. Your product may
not feature some functions specied in the manual. These functions
are marked by the sign *. Your product must be installed and introduced by Simfer authorized service.
Our products are intended for commercial use.
"PLEASE READ THE MANUAL BEFORE INSTALLING
OR USING THIS PRODUCT."
This product has been produced in modern environment-friendly facilities without adversely aecting nature.
"Complies with AEEE Regulation"
2
Page 3
CONTENTS
SECTION 1
Safety Warnings..................................................................4
SECTION 2
Overview and Technical Specications.................................9
Technical Specications ....................................................10
SECTION 3
Installation and Initial Operation.........................................12
Glass Mounting Instructions...............................................14
Castor Mounting Instructions.............................................15
SECTION 4
Installation.........................................................................18
Operation of the Freezer......................................................19
Thermostat Setting.............................................................20
SECTION 5
Cleaning, Maintenance and Transportation of Your Freezer..22
What To Do Before Calling For Authorized Service.............25
SECTION 6
Compliance With AEEE Regulations And Waste Disposal
and Packaging Information................................................26
Warranty Certicate.......................................................28
3
Page 4
SAFETY WARNINGS
1. Your product is set for 220-240 V 50 Hz mains
power. Use of incompatible voltage may cause your
product to become inoperable or a re.
2. Your product is designed and manufactured
only to preserve frozen packaged foods in applicable
temperature. Do not place consumables such as beverages for cooling. Please do not use other than as
indicated.
3. Electrical installation shall conform with the legal regulations.
4. Do not place the your product under direct sunlight or within the inuence area of heat sources, such
as an air conditioner, stove, radiator, furnace, oven,
heater or infrared heater. Otherwise, the freezer may
perform poorly, get damaged or become inoperable.
5. Choose a place without moisture but with air
circulation allowed.
6. Clean the inside of your product prior to rst
use.
7. Do not allow children to get into the product or
play around it.
8. If your product has a cover lock, keep its key in
a safe place. By the end-of-life of the product, deactivate the cover lock of your freezer before disposing
it. It is of utmost importance that children are not left
in the freezer, doing so may result in a life endangering situation.
4
Page 5
9. For your safety, in order to eliminate the risk of
electric shock and re there must be a breaker system with a residual current device in your electrical
wiring. Our rm is not responsible for failures and
losses which may occur as a result of using the product on an ungrounded grid.
10. Do not place explosive or ammable material in
your product.
11. Do not use any sharp, pointed objects to scrape
the icing that may occur on the inner surfaces of
your product. Only use the ice scraper that is provided with your product. Otherwise you can damage the
cooling surface of your product. Also, this improper
operation may cause gas leak and render your product inoperable.
12. After putting your product into place, allow at
least 2 hours without moving it before rst use.
13. Your product is designed for indoor use. Do not
use your product outdoors.
14. The installation, placement, maintenance and
cleaning of your product should be performed as
prescribed in the manual. In case of damage to your
product due to misuse, the warranty of the product
will be invalidated.
15. Avoid any sharp and pointed object or overheated material from contacting with glass surface
of glass-cover products as this may cause the glass
to crack or break.
5
Page 6
16. In order to avoid your product from sliding or
overturning, place the product on a non-tilted at
surface. Adjust the height of pre-set legs after placement.
17. In case of any failure within your product, taking
measures for food preserved within the deep freeze
is fully under responsibility of the user. Our company
is not responsible for spoilt food due to any failure or
misuse.
18. Never use an extension cord or multi-plug with
your product.
19. Never use pressured water to clean. Pressured
water may damage live-current parts.
20. Place the packaging material of the product
where children cannot reach. Some packaging material (such as nylon, styrofoam, etc.) may be dangerous for children.
21. The product should not be used by the physically, visually, mentally handicapped -including the
hearing impaired-, children, non-experienced or
non-informed persons without supervision of a person responsible for the safety of such people.
22. Open the conservator cover only when necessary. Please make sure that the lid is sealed properly
when it is not necessary.
23. In the event of a sudden power outage unplug
your product. Plug back in 20 minutes after you make
sure that the mains become normal.
6
Page 7
24. Do not put domestic or wild animals inside your
product and do not allow them to enter into your
product. These kind of living creatures might damage
the electrical system and cause a re.
25. Frost shall be increased for products, of which
the doors are kept open or frequently open and
closed, and the product shall have diculty in performing the cooling operation. Thus, open the door
of your product when it is required only. Ensure that
the door of your product is closed when you do not
require.
26. Do not unplug your product for saving power if
you shall not use your product or keep it empty for
a short period. Otherwise, more power shall be used
for cooling your product again. Just bring the thermostat position to a lower setting.
27. Follow the instructions specied in this manual
for replacement of lamps. The rating of the lamp to
be replaced is specied on the identication plate of
the product and on the plate under the lamp.
28. Do not interfere with the product directly in case
of a fault that occurs due to the electrical system of
the product or of the installation where the product
is connected. Unplug the product and disconnect the
power of the device by turning the main switch o
and contact nearest Simfer authorized service.
29. Do not store explosive materials such as aerosol
cans with ammable propellants inside this product.
7
Page 8
30. If the power supply cable is damaged, it must be
replaced by its manufacturer or authorized technical
service or any other personnel qualied at the same
level, in order to avoid any dangerous situation.
31. If the appliance will not be used for extended
periods, the glass covers shall be removed.
Attention!
• This appliance includes inammable
and explosive gas R404A, R600a,R134a, R290.
• The ventilation holes on the casing or the
body of the appliance shall be kept open to prevent blocking
• Do not use mechanical tools or other mechanisms except the ones recommended by the
manufacturer to make defrosting quicker.
• The cooling circuit shall not be damaged.
• Except materials recommended by the manufacturer, no electric appliances should be used
within food storage compartment of the appliance.
• In order to decrease the risk of ignition, this
appliance shall only be installed and maintained
by Simfer services.
8
Page 9
SECTION 2
OVERVIEW AND TECHNICAL SPECIFICATIONS
Aluminium Frame Prole
Glass Cover
Handle
Lock
External
Body
(Advertisement
Application
Area)
Castors
9
Page 10
TECHNICAL SPECIFICATIONS
Brand Simfer Simfer Simfer
Model SYD 650 MD DC SYD 550 MD DC SYD 410 MD DC
Product Category
Refrigerant R404A R404A R404A
Total Gross Volume (lt) 640 534 416
Total Net Volume (lt) 532 443 345
Cooling System STATIC STATIC STATIC
Climate Class BC1 (35C/75% Rh) BC1 (35C/75% Rh) BC1 (35C/75% Rh)
Noise Level (dB(A)) 45-47 45-47 45-47
Height (with castor)
(mm)
Width (mm) 1902 1620 1314
Depth (mm) 653 653 653
Net Weight ()kg 85 75 65
Electric Input (V/Hz) 230 230 230
COMMERCIAL
CONSERVATORS
919 919 919
COMMERCIAL
CONSERVATORS
COMMERCIAL
CONSERVATORS
Total Power (W) 440 420 290
10
Page 11
Brand Simfer Simfer Simfer
Model SYD 310 MD DC SYD 210 MD DC SYD 150 MD DC
Product Category
Refrigerant R404A R404A R404A
Total Gross Volume (lt) 314 208 133
Total Net Volume (lt) 258 170 107
Cooling System STATIC STATIC STATIC
Climate Class BC1 (35C/75% Rh) BC1 (35C/75% Rh) BC1 (35C/75% Rh)
Noise Level (dB(A)) 45-47 45-47 45-47
Height (mm) 919 919 919
Width (mm) 1039 763 573
Depth (mm) 653 653 573
Net Weight ()kg 55 45 40
Electric Input (V/Hz) 230 230 230
COMMERCIAL
CONSERVATORS
COMMERCIAL
CONSERVATORS
COMMERCIAL
CONSERVATORS
Total Power (W) 210 180 150
Power consumption test standard for commercial type products is
prEN 16902.
Specications of the product are available on the identication
plates on the product. Simfer reserves the right to make changes
on the specications of the products without prior notice.
11
Page 12
SECTION 3
INSTALLATION AND INITIAL OPERATION
Selection of Installation Places
Operating environment of the product is very important to ensure
that your product operates without any problem. When you are selecting the operating environment,
• Do not place your product outdoors so that it shall be exposed to
weather conditions. (on a street, lane, etc.)
• Do not place materials such as cardboards, boxes, etc. in front of
the lower blinds to ensure proper cooling of your product.
• Place it at least one (1) meter away from heat sources. (stove, radiator, electrical heater, etc.) (Figure 1)
• Do not expose to direct sunlight. Operation rate of your product will
be increased if sunlight hits the glass of your freezer. And this causes
an increase in the temperature of the products inside the product and
the power consumption shall be increased. (Figure 2)
• Do not place it against A/C exhausts, under the fans and directly in
the door and window openings. (Figure 3)
• Air entrance and exit shall always be free and easy for proper operation of the compressor section of your product.
• Make sure that there is a clearance of 150 mm (15 cm) between
the wall and the rear side of your freezer when you are bringing the
product close to the wall.
Picture 1 Picture 2 Picture 3
12
Page 13
The voltage and frequency of mains power should be the
same as the values specied on the label behind your appli-
!
ance. If mains power is far below or above the specied values,
have the desired voltage by using a voltage regulator. You can get
help from a qualied electrician. The fuse of the mains socket should
be maximum 16A.
CAUTION!
On installations performed by the Simfer authorized service, customer shall be informed and advised about the proper installation location,
however nal decision on the installation location shall be made by the
customer.
Simfer Authorized Service species the process mentioned above on
the relevant installation service form. Customer shall be solely responsible for any damages that may occur due to the installation location
decided as per the nal decision of the customer.
13
Page 14
GLASS MOUNTING INSTRUCTIONS
Place your product on a at, level ground. Mount your glass by placing it on the mounting rack below by placing one side, then placing on
the other side and x it as shown in Figure 2.
. Place the glass stoppers, tabs facing back, on the lower and upper
rack and press them to ensure that they are xed on the racks, as
shown in Figure 3. Apply the same procedure on the other side, place
the 4 stoppers on the lower and upper racks. Pull the glass to the right
side.
. Mount your glass by placing it on the mounting rack above by placing one side, then placing on the other side and pull the upper glass to
the right as shown in Figure 4.
Figure 1 Figure 2
Figure 3 Figure 4
14
Page 15
. Place the glass stoppers, tabs facing back, on the lower and upper
rack and press them to ensure that they are xed on the racks, as
shown in Figure 5. Apply the same procedure on the other side, place
the 4 stoppers on the lower and upper racks. Complete the mounting
procedure by pulling the glass to the left side.
CASTOR MOUNTING INSTRUCTIONS
Picture 5
• Place your product as shown in Figure 2. Then, mount two castors with brakes in the to the back side of the conservator, by xing
the castors in the sockets under the conservator and ensure that the
socket centers are aligned, as shown in gure 4. Then place the U-pins
through the holes. Ensure the stability by placing the pim wedges.
•By placing the conservator as shown in gure 3, mount the two
castors in the castor box as shown in gure 5, by applying the same
procedure.
Picture 1
Picture 2
15
Picture 3
Page 16
Climate Class Description
Your freezer provides best cooling performance in the conditions
specied below as per the climate class. Thus, ensure that the environment where your freezer shall be used conforms with this temperature
ranges.
Figure 4
Figure 5
Figure 5
Climate Class Minimum operating
ambiant temperature and
humidity
A +16 °C, 80 % 30 °C, 55 %
B +16 °C, 80 % 35 °C, 75 %
C +16 °C, 80 % 40 °C, 40 %
16
Maximum operating
temperature
ambiant temperature
and humidity
Page 17
Product Climate Class Description
This is the temperature range determined by the protection temperature of the product to be placed inside the freezer.
Climate Class Hottest product temperature
C1 -18,0 ºC
C2 -7,0 ºC
S Special product classication
SİMFER conservators you have purchased have the climate class of
BC1 and they are manufactured so that they shall operate in an average ambient temperature between +16ºC and +35ºC.
Operating the product out of the mentioned temperature range may
cause performance losses.
17
Page 18
SECTION 4
LOCATION
Possible Installation Locations:
1- Ensure that a clearance of 150 mm (15 cm) is available between
the wall and your freezer so that solely the back of your freezer faces
the wall.
2- When you place it on the corner, leave a clearance of 150 mm (15
cm) on its back so that it faces the corner. You may lean the side on
the corner to the wall. (Figure 4)
The most important point for any kind of placement is that the ventilation of the compressor assembly is not blocked. Place your product
so that it is not inclined in any way and that it is standing on its legs
or castors and then operate it. (Figure 5)
Your product shall operate more eciently when the ventilation of
the compressor assembly is better.
Figure 4 Figure 5
INSTALLATION
Take o and remove all package materials and lower wooden pallet of
your product before placing it. (It may be required to lift the freezer to
remove the base bracket).
Install spare parts provided inside your product as per the installation
18
Page 19
instructions. Use only genuine Simfer spare parts.
Non-genuine spare parts may cause risks for you and may damage
your product.
Place your product where you desire. Consider the placing rules specied in the manual during placement.
Level your product laterally and vertically with a spirit level. Perform
the levelling procedure with the adjustable legs on the front lower part
of your freezer.
OPERATION OF THE CONSERVATOR
Rules for Electrical Connection
Your product shall operate when you plug it to an outlet.
CAUTION!
Do not plug your product to a multi-socket or do not use an extension cord.
Your product is not equipped with an on/o switch.
Do not allow the cables of your product connected to the mains to
contact hot surfaces. Outlet that shall be used shall always be grounded. It the outlet that shall be used shall also be protected with a proper
fuse with a rating of 10-16 A minimum. Always get support from our
authorized service or a qualied electrician for the fuse that shall be
installed on the electrical installation where the outlet is connected.
(Figure 6)
The voltage and frequency of mains power should be the same as the
values specied on the label on the inner surface of your product. If
mains power is far below or above the specied value, have the desired
voltage by using a voltage regulator.
You can get help from a qualied electrician.
Do not put the cable of your product on passage routes. These may
cause injury to you and damage to your freezer.
19
Page 20
Figure 6
THERMOSTAT SETTING
Temperature settings of your freezer is performed in our factory for
operation in suitable conditions.
Temperature for the preservation of the food is adjusted with the
thermostat by observing it from the thermometer on your freezer (optional).
Internal temperature of your freezer may be adjusted by rotating the
thermostat switch. Position “7” on the thermostat shall decrease the
internal temperature to the minimum level. Internal temperature of
your product may be set between -16°C and -24°C.
Loading Food Into Your Freezer
You may load any food you desire as per the examples provided in
this manual in your freezer when the freezer has reached the desired
temperature as empty. (If your product model is equipped with a thermometer, you may control the internal temperature here.
Always consider the maximum load capacity while loading frozen
food in your product. Do not exceed the loading mark on your product.
WARNING! Operate your product three (3) hours without load before loading your food.
Do not put materials that shouldn't be cooled in your product.
The basket carriage capacities used in your product are specied below.
20
Page 21
DEFROSTING OPERATION
High temperatures and humidity and frequent operation of your
product may increase the rate of frost. The more the frost, the more
the operation time. And this causes an increase in the power consumption. Turn o your product and make sure that the frost is removed in such a case
21
Page 22
SECTION 5
CLEANING, MAINTENANCE AND TRANSPORTATION OF YOUR
CONSERVATOR
CLEANING
Cleaning of your product consists of two stages, namely internal
cleaning and external cleaning.
Always follow the warnings below before starting the cleaning operation.
WARNING!
• Always unplug your freezer before any cleaning operation.
• Always wear protective gloves during cleaning and maintenance.
This will protect you against injuries.
• Never use domestic cleaning agents and abrasive - scratching material to clean (ammable, ignitable and abrasive naterials such as surface cleaners, detergents, fuel oil, thinner, acids, etc.). Otherwise, discolouration may occur on the plastic parts of the product.
CLEANING AND MAINTENANCE
1. For eciency of your deep freeze, perform cleaning and mainte-
nance at least once in a year.
2. Unplug your freezer from mains power before cleaning it.
3. Always wear protective gloves during cleaning and maintenance.
This will protect you against injuries.
4.Do not use domestic cleaning agents and abrasive - scratching materials to clean. Never use owing or pressured water to wash.
5. Never wash inside or outside of your product. This may give damage to your product or cause electric shock.
MAINTENANCE
The product does not require periodic maintenance.
22
Page 23
Internal Cleaning
• Place the products inside your freezer to a cool environment where
they shall retain their temperatures.
• İBefore performing internal cleaning, wait until the temperature of
the inner parts of the product increases up to the ambient temperature.
• Always wear protective gloves during cleaning and maintenance.
This will protect you against injuries.
• Remove the accessories.
• Perform cleaning by using a soft cotton cloth and warm water.
• Dry it by using a dry cotton cloth. If it is not dried, it may turn black
in time.
• Ensure that the inner surface is not wet or moist after cleaning.
• You can reload your food 2 hours after operating based on the type
of operating specied within this manual.
External Cleaning
Clean by using cotton cloth and warm water. Prevent cleaning water from entering the front electrical and illumination sections during
cleaning. Clean the door seal using only clean soapy water.
Attention! Never use chemical agents such as commercial cleaning
agents, scratching detergents, acids.
Turning O Your Conservator
Place the food in the product where appropriate.
• Unplug your product. Perform the following if your product shall
not be used for a long period;
• Clean your product. Otherwise, moisture remaining on the walls of
the product may cause darkening on the inner surface.
23
Page 24
WARNING! If your product shall be stored in a closed environment
after turning it o;
Do not cover your product with plastic material. A plastic material
may cause your product release odour and perspiration as it does not
permeate air through it. Perspiration may cause rusting.
If you do not keep your product with its door open, it may release
odour.
WHEN TRANSPORTING,
1. Remove the plug from the outlet.
2. Melt the ice.
3. Wipe the inner surfaces and oor with a damp cloth.
4. Transport it in the normal operating position.
24
Page 25
WHAT TO DO BEFORE CALLING FOR AUTHORIZED SERVICE
Failure Possible Solution Result
If the freezer does not
operate (No noise or
just the fan noise)
Internal temperature of
the product is high
Internal temperature
of your product is very
low
Excessive perspiration
inside the product and
on the window.
Bad odours can be
smelt under your freezer.
It may be caused by
the thermostat. It may
be unplugged. Fuse
may be blown or faulty.
Condenser ns may be
dirty or clogged.
Ambient temperature
is very high or thermostat setting is incorrect.
Rear part is very close
to the wall, ventilation
blinds are blocked or
its front is covered. It
may be exposed to excessive external wind.
Condenser ns are very
dirty
Wrong internal thermostat setting
Water drainage hole
may be clogged for internal perspiration. Humidity level of external
environment is higher
than 65% for perspiration on the window.
Lower water drainage
tray is dirty. (Applies to
some models.)
It shall operate again
when it reaches the
proper temperature.
Plug it correctly. Consult Simfer authorized
service or a qualied
electrician.
Take your freezer to a
place where ambient
temperature is lower.
Bring it to specied
clearance. Clean the
front of the ventilation
blinds. Prevent wind.
Clean the condenser
ns.
Reset the thermostat.
Clean the water drainage hole. For high humidity conditions, you
may place your freezer
in a location with less
humidity.
Clean the water drainage tray.
Power ratings of the lamps or LEDs used in your products are
specied on the plate inside the freezer or in the installation area of the
lamps. Lamps and LEDs used in your products should only be operated
on by Simfer Authorized Services.
25
Page 26
SECTION 6
COMPLIANCE WITH AEEE REGULATIONS AND WASTE DISPOSAL
1. This product does not contain the dangerous and
prohibited materials indicated in "Waste Electrical and Electronic Equipment Control Regulation" published by Ministry
of Environment and Urbanisation of Republic of Turkey. Complies with AEEE Regulation.
2. This product was manufactured from recyclable and
reusable high quality parts and materials. Therefore, do not dispose
of this product with other domestic wastes at the end of its life cycle.
Take it to a collection point for electrical and electronic equipment.
You can ask your local administration about these collection points.
You can help protect the environment and natural resources by delivering the used products for recycling. Before disposing of the product, cut the power cord and break the locking mechanism to make it
inoperable for children's safety.
PACKAGE INFORMATION
The product's packaging is made of recyclable materials, in accordance with the National Legislation. Do not dispose the packaging waste
with the household waste or other wastes, dispose it to the packaging
collection areas specied by local authorities.
Follow the instructions specied in the manual.
If the product is still not running normally despite the controls you
have made,
call for authorized service.
26
Page 27
WE, AS THE MANUFACTURER/EXPORTER,
SERSİM DAYANIKLI TÜKETİM MALLARI KOLLEKTİF ŞİRKETİ, HEREBY DECLARE THAT THE
DEVICE, DETAILS OF WHICH ARE SPECIFIED BELOW COMPLIES WITH ALL THE BASIC SECURITY REQUIREMENTS OF THE “REGULATION ON ELECTRICAL INSTALLATIONS DESIGNED TO BE
USED WITHIN CERTAIN VOLTAGE LIMITS-LVD (2006/95/AT)”, WHICH HAS BECOME EFFECTIVE UPON BEING PUBLISHED IN THE OFFICIAL GAZETTE DATED 30.12.2006 AND NO.26392
AND THE “ELECTROMAGNATIC COMPLIANCE REGULATON-EMC (2004/108/AT)” WHICH HAS
BECOME EFFECTIVE UPON BEING PUBLISHED IN THE OFFICIAL GAZETTE DATED 24.10.2007
AND NO.26680 AND THAT THE RESPONSIBILITY IN RELATION THERETO, HAS BEEN ASSUMED.
PRODUCT NAME: LATERAL CONSERVATOR
MODEL:
20Y150MF 20Y410MF
20Y210MF 20Y550MF
20Y310MF 20Y650MF
STANDARDS APPLIED:
LVD: EN 60335-1 2012+A11
EN60335-2-89 2015-05+A1+A2
EC CONFORMITY DECLARATION
EMC: EN55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2014 CLASS A
EN 61000-3-3:2013
EN 61000-4-2:2009
EN 61000-4-4:2004+A1:2010
EN 61000-4-5:2006
EN 61000-4-6:2009
EN 61000-4-11:2004
DATE OF ISSUANCE: 12/10/2016
COMPANY ADDRESS
SERBEST BÖLGE 12.CADDE NO:18 KAYSERİ/TURKEY
27
Page 28
H10-20-320-057
Loading...