Simfer S 3100 WT, S 3150 WT, S 3000 WT, S 3050 WT, S 2200 WT User Manual

...
Dear Customer,
Thank you for preferring Simfer products. We aim to ensure that you can obtain utmost efficiency from this product made in accordance with the sense of total quality in a meticulous working environment at our modern facilities without causing any harm to the nature. We recommend you to carefully read the User Manual before using the Simfer quartz heater and to keep it permanently so that it can maintain its original features for a long time and serve you as efficiently as possible. NOTE: This User Manual has been prepared for several models. Some features specified in the manual may not be available in your device. These features are market with “*”. The devices are for domestic use. There are not intended for commercial use.
PLEASE READ THE INSTRUCTIONS BEFORE ASSEMBLING OR USING
THE DEVICE” This product has been produced in modern, environmentally friendly facilities without causing any harm to the nature.
“It complies with the EEE Directive”
1
CONTENTS: Dear Customer ……………………………………………………………………………... 1 Contents …………………………………………………………………………………….. 2 Safety Instructions ……………………………………………………………………..… 3, 6 Technical Features
Device Equipment …………………………………………………………………… 7 Device Equipment, Foot Assembly .…………………………………………………. 8 Usage of the Humidifier Section, Control Panel ………………..…………………… 9 Control Panel, Usage of the Humidifier ..…………………………………………… 10 Technical Table, Usage of the Heater ………………………………………..………11
Maintenance and Cleaning ……………………………………………….………………. 12 Troubleshooting …………………………………………………………..……………….. 13
Certificate of Warranty ………………………………………………………………….... 14
2
SAFETY INSTRUCTIONS
This device has been produced in accordance with safety regulations. Operation in violation of the rules may cause harm to people and the device. Read the user manual carefully before operating the device. You can find important information about assembly, safety, operation and maintenance in the user manual. This way you can both protect yourself and prevent the device from getting damaged. If the Supply Cord is damaged, it must be replaced by the manufacturer or its service agency or equally qualified personnel in order to prevent a dangerous situation. The heating tube available on the device must be checked for cracks and deformation. If the glass tubes are damaged, the heater must not be used and the authorized service must be contacted. It must be checked whether the main power line is 220-240V AC, 50-60 Hz and connected to the circuit breaker. Network safety must be checked. The circuit breaker must be 16 amperes. The device must be certainly used with grounded receptacle and the grounded receptacle must be away from the heater area and hot surface. Furthermore, looseness and damage check must be performed on the receptacle. Loose receptacles cause harm to the device and installation.
The device must not be connected to the same electric cable or circuit breaker as other devices. The power cable must not be left on or near the hot body of the device. If the device is not to be used for a long time, moved to another place, cleaned or calibrated, the plug of the device must be disconnected. It must be made sure that the device has cooled down. Do not use the device in places very close to any bathroom, shower or swimming pool.
3
SAFETY INSTRUCTIONS
This device is not intended for use by physically, emotionally, and mentally disabled people (including children) or people with insufficient experience and knowledge unless a person responsible for safety of the device provides supervision and direction regarding the operation of the device. Do not let the device touch water under any circumstances. The electric connection of the device must be disconnected from the network during assembly and maintenance or repair works. The device must be unplugged in order to disconnect it from the network. Make sure the supply cable and receptacle are clean and dust free before operation. Do not pull by the cable while unplugging the supply cable. Make sure to hold properly while plugging or unplugging the device. Do not touch the supply cord with wet hands. Do not make any additions to the supply cord. Otherwise it may result in malfunction, electric shock or fire. Do not pass the supply cable under heavy objects. Otherwise it may cause electric shock or fire hazard. Do not shut down the heater only by unplugging it and deactivating the circuit breaker; always use the heating element function button. As covering or misplacement of the heater causes fire hazard, this heater may not be used together with any automatic programmer, timer or any other mechanism. The fireguard of this heater aims to prevent direct access to heating elements and it must be in place while the heater is in operation.
4
SAFETY INSTRUCTIONS
Do not use the device for any other purpose other than the intended use. (Do not use it for drying clothes or keeping animals or plants warm) Do not attempt to clean the device using solvents or flammable liquids. (This may cause electric shock or fire) Do not use the device while sleeping or when you are away from the device. Avoid using extension cables as this may cause fire due to overheating. If you have to use an extension cable, the cable section must be at least 2 mm2 (14 AWG). The device must be used on a flat and smooth ground. Do not use the device in unstable or insecure places. Do not attempt to demount or repair the heater. Do not shake the heater under any circumstances. A little smoke and smell may be released during the first use. This is normal. Do not touch the device while it is in operation or immediately after shutting it down. The device must be unplugged before cleaning. Do not clean the device with steam cleaners. Children must be watched to ensure that they do not temper with the device. The fireguard does not provide complete protection for little children and disabled people. Keep the device in dry and enclosed spaces. The devices must be used only with the resistances in horizontal position (on the feet).
5
SAFETY INSTRUCTIONS
The distance between the device and ceiling must be minimum 0.75 meters. There must be minimum 1 meter distance between the device and curtains, wood, cartons, fabrics and other materials, living organisms and other devices. No finger or any other object must be put through the protective screen. The device must not be placed right under any receptacle. Do not move the device while it is in operation. The resistances may be sensitive and malfunction when they are hot. Always shut down the device and wait for it to cool down before touching it. Do not cover the device in order to prevent overheating. Do not block the ventilation ducts and the wire area. Do not operate the device as close as 7.60 meters to inflammable materials (petrol, alcohol etc.) or place motor vehicles not expected to operate near it. Do not put flammable materials such as solvents, thinner etc. on or near working surfaces of heating devices or do not place electrical home appliances near them.
6
TECHNICAL FEATURES Device Equipment (Slim)
Vapor discharge and water filling point
Heating glass tube
Protective screen
Plastic foot
Device Equipment (Tower)
Vapor discharge and water filling point
Heating glass tube
Protective screen
Louvers
Holder
Thermostat Heating function
Fan and Vapor function
Louvers
Plastic Holder
Thermostat
Heating function
Fan and Vapor function
Plastic foot
7
TECHNICAL FEATURES Device Equipment (Slim, Tower)
Vapor discharge and water filling point
Plastic holder
Lighted water level indicator
Foot assembly
Vapor discharge and water filling point
Plastic holder
Lighted water level indicator
The foot assembly must be as indicated in the picture above. Apply pressure with your hand from the foot to the body after making sure that the protrusion on the foot corresponds to the duct. A click sound will be heard when the nails fit in their places. After making sure that the foot is in position, it must be secured with the screw available in the box as shown in the figure above.
8
TECHNICAL FEATURES
t
t
t
t
t
t
t
t
Control Panel (Slim)
Off
s
1
level resistances (in the 1 2nd level resistances (in the 1 3rd level resistances (in the 1 4th level resistances (all)
Thermostat Turbo Fan
Humidifier
Control Panel (Tower)
Off
s
1
level resistances (in the 1 2nd level resistances (in the 1 3rd level resistances (in the 1
s
row)
s
and 4th rows)
s
, 2nd, and 3rd rows)
s
row)
s
and 3rd rows)
s
, 2nd, and 4th, 5th rows)
9
4th level resistances (all) Turbo Fan
Humidifier
TECHNICAL FEATURES Usage of the Humidifier Section (*) Option
1. Open the cover as indicated in the figure.
2. Check the water level and add enough water to the device from the opening. The water
capacity is about 330 ml.
3. Attention! As adding too much water will cause overflow, it may damage the electric
parts of the device and cause electric shock.
Water filling point
Slide in the arrow direction
Slide in the arrow direction
Water filling point
Usage of the Humidifier
1. Use the water filling point shown in the picture to fill water.
2. Check the water level and add enough water to the device from the opening. The water
capacity is about 150 ml.
3. Attention! As adding too much water will cause overflow, it may damage the electric
parts of the device and cause electric shock.
4. Watch the water indicator while adding water to the device. The water level must not
exceed the point indicated by the water indicator. Water must be added to the device when the water amount is reduced to ¼. Water reduced to ¼ will not evaporate. Operating the device without water and in steam mode may damage the device.
10
TECHNICAL FEATURES Technical Table
MODEL S 3100 – 3150 WT S 3000 – 3050 WT
Height (A) 680 mm 705 mm Width (B) 725 mm 510 mm Depth (C) 260 mm 255 mm
Dimensions
Supply (V/Hz) 220-240V AC, 50-60 Hz 220-240V AC, 50-60 Hz Current Draw (A) 12.2 A 11.9 A Protection Level IP 20 IP 20 Device Class I I Level 1 700 W 550 W Level 2 1400 W 1100 W Level 3 2100 W 2200 W Level 4 2800 W 2750 W Level 5 --------- --------­Rated Power (W) 2800 W 2750 W
USAGE OF THE HEATER
Plug the heater to a suitable grounded receptacle. Bring the ON/OFF switch to operating position. Attention! The device is equipped with a safety system. In case of any rollover, the safety system will engage and cut off the electricity. Careful and regular maintenance in line with the recommendations given in this manual is crucial in order to operate the device efficiently for a long time. The pollution of the reflector (reflecting mirror) and quartz glass tubes must be checked at least once a month by the user. If they are dirty, the cleaning and maintenance instruction must be performed. The said checks must be conducted more frequently depending on the dust amount in the operating environment.
One heating resistance works independently of the thermostat while the product is in operation as a precaution.
11
MAINTENANCE AND CLEANING Maintenance
Careful and regular maintenance in line with the recommendations given in this manual is crucial in order to operate the device efficiently for a long time.
- The pollution of the reflector (reflecting mirror) and quartz glass tubes must be
checked at least once a month by the user. If they are dirty, the cleaning and maintenance instruction must be performed.
- The said checks must be conducted more frequently depending on the dust amount in
the operating environment.
- The power cable and plug must be checked while cleaning the device. If the power
line or plug has been deformed, they must be taken to the authorized service.
- Reflector, wire, and body deformation must be visually checked while cleaning the
device. If there is any deformation, the authorized service must be called for necessary actions.
- It is recommended to replace the reflector every two years in order for the device to
run more efficiently. The reflector must be replaced by the authorized service. Keeping the reflector clean ensures maximum heating efficiency of the device.
Cleaning
Attention! The device will work more effectively and last longer if regular and careful cleaning is performed by the user.
- The device must be turned off and the power cable of the device must be disconnected
and left to cool down before cleaning.
- If the reflector (reflecting mirror) and quartz glass tube are dirty, they must be cleaned
externally with dry air without removing the protective screen wire if possible.
- The outer surface of the device must be cleaned with soft cotton cloth or soft brush.
- Do not use corrosive materials of solvents for cleaning the heater. Such substances
may damage the plastic parts.
- Do not clean the device with steam cleaners.
12
TROUBLESHOOTING
You can solve possible problems of the device by checking the following points before calling the technical service.
PROBLEMS SOLUTIONS
The device does not work Check whether the plug has been connected properly.
Check whether the device is standing upright. (The device has balance safety) Check whether the switch and thermostat of the device are in correct and open position. Check whether there is any problem with the electric installation of the house. Make sure you are implementing the operating instructions correctly.
13
If the problem continues, contact the nearest Simfer authorized service
Loading...