Simfer F66HB45016 User Manual [ru]

Gas and electric VWRYHZLWKovenV

Модели:

User manual Руководство пользователей

 Ʉɨɦɛɢɧɢɪɨɜɚɧɧɚɹɩɥɢɬɚ ɞɭɯɨɜɵɯɲɤɚɮɚ  [[

Dear user,

Our objective is to make this product provide you with the best output which is manufactured in our modern facilities in a careful working environment, in compliance with total quality concept.

Therefore, we suggest you to read the user manual carefully before using the product and, keep it permanently at your disposal.

Note: This user manual is prepared for more than one model. Some of the features specified in the manual may not be available in your appliance.

All our appliances are only for domestic use, not for commercial use.

Products marked with (*) are optional.

“THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE REGULATIONS FORCE AND ONLY USED IN A WELL VENTILATED SPACE. READ THE INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE”

“Conforms with the WEEE Regulations."

Contents

Important warnings 4 Electrical connection 16 Gas connection 17 Introduction of the appliance 23 Accessories 24 Technical features of your oven 25 Installation of your oven 28 Chain lashing illustration 30 Control panel 30 Using oven section 31 Using the grill 32 Using the chicken roasting 32 Using cooker section 33 Program types 35 Cooking time table 36 Maintenance and cleaning 37 Cleaning and maintenance of the oven's door 38 Catalytic walls 39 Rack positions 39 Changing the oven lamp 40 Using the grill deector sheet 41 Troubleshooting 42 Handling rules 44 Recommendations for energy saving 44 Environmentally-friendly disposal 45 Package information 45

IMPORTANT WARNINGS

1. Installation and repair should always be performed

by “AUTHORIZED SERVICE”. Manufacturer shall not be held responsible for operations performed by unauthorized persons.

2. Please read this operating instructions carefully. Only by this way you can use the appliance safely and in a correct manner.

3. The oven should be used according to operating instructions.

4. Keep children below the age of 8 and pets away when operating.

5. WARNING: The accessible parts may be hot while using the grill. Keep away from children.

6. WARNING: Fire hazard; do not store the materials on the cooking surface.

7. WARNING: The appliance and its accessible parts are hot during operation.

8. Setting conditions of this device are specied on

the label. (Or on the data plate)

9. The accessible parts may be hot when the grill is used. Small children should be kept away.

10. WARNING: This appliance is intended for cooking. It should not be used for other purposes like heating a room.

11. To clean the appliance, do not use steam cleaners.

12. Ensure that the oven door is completely closed

after putting food inside the oven.

13. NEVER try to put out the re with water. Only shut

down the device circuit and then cover the ame with a cover or a re blanket.

14. Children under 8 years of age should be kept away, if they cannot be monitored continuously.

15. Touching the heating elements should be avoided.

16. CAUTION: Cooking process shall be supervised. Cooking process shall always be supervised.

17. This device can be used by children over 8 years

of age, people with physical, hearing or mental challenges or people with lack of experience or knowledge; as long as control is ensured or information is provided regarding the dangers.

18. This device has been designed for household use only.

19. Children must not play with the appliance. Cleaning or user maintenance of the appliance shall not be performed by children unless they are older than 8 years and supervised by adults.

20. Keep the appliance and its power cord away from children less than 8 years old.

21. Put curtains, tulles, paper or any ammable (ignitable)

material away from the appliance before starting to use

the appliance. Do not put ignitable or ammable materials

on or in the appliance.

22. Keep the ventilation channels open.

23. The appliance is not suitable for use with an external

timer or a separate remote control system.

24. Do not heat closed cans and glass jars. The pressure may lead jars to explode.

25. Oven handle is not a towel drier. Do not hang towels, etc. on the oven handle.

26. Do not place the oven trays, plates or aluminium foils directly on the oven base. The accumulated heat may damage the base of the oven.

27. While placing food to or removing food from the oven, etc., always use heat resistant oven gloves.

28. Do not use the product in states like medicated

and/or under inuence of alcohol which may affect your

ability of judgement.

29. Be careful when using alcohol in your foods. Alcohol

will evaporate at high temperatures and may catch re to cause a re if it comes in contact with hot surfaces.

30. After each use, check if the unit is turned off.

31. If the appliance is faulty or has a visible damage,

do not operate the appliance.

32. Do not touch the plug with wet hands. Do not pull the cord to plug off, always hold the plug.

33. Do not use the appliance with its front door glass removed or broken.

34. Place the baking paper together with the food into a pre-heated oven by putting it inside a cooker or on an oven accessory (tray, wire grill etc.).

35. Do not put objects that children may reach on the

appliance.

36. It is important to place the wire grill and tray properly on the wire racks and/or correctly place the tray on the rack. Place the grill or tray between two rails and make sure it is balanced before putting food on it.

37. Against the risk of touching the oven heater elements, remove excess parts of the baking paper that hang over from the accessory or container.

38. Never use it at higher oven temperatures than the maximum usage temperature indicated on your baking paper. Do not place the baking paper on the base of the oven.

39. When the door is open, do not place any heavy object on the door or allow children to sit on it. You may cause the oven to overturn or the door hinges to be damaged.

40. The packaging materials are dangerous for children. Keep packaging materials away from the reach of children.

41. Do not use abrasive cleaners or sharp metal scrapers to clean the glass as the scratches that may occur on the surface of the door glass may cause the glass to break.

42. Do not place the appliance on a surface covered with carpets. Electric parts gets overheated since there will be no ventilation from below. This will cause failure of the appliance.

43. Do not hit glass surfaces of vitro-ceramic cookers

with a hard metal, resistance can get damaged. It may cause an electric shock.

44. User should not handle the oven by himself.

45. Use shall be careful when cleaning gas burners.

It may cause personal injuries.

46. Food can spill when foot of oven is dismantled or gets broken, be careful. It may cause personal injuries.

47. During usage, the internal and external surfaces of the oven get hot. As you open the oven door, step back to avoid the hot vapour coming out from the interior. There is risk of burning.

48. Upper cover of the oven can be closed for a reason, than cookware can trip over. Step back to avoid the hot food coming on you. There is risk of burning.

49. Do not place heavy objects when oven door is open, risk of toppling.

50. User should not dislocate the resistance during cleaning. It may cause an electric shock.

51. Do not remove ignition switches from the appliance. Otherwise, live electric cables can be accessed. It may cause an electric shock.

52. Oven supply can be disconnected during any construction work at home. After completing the work, re-connecting the oven shall be done by authorized service.

53. Do not place metal utensils such as knife, fork, spoon on the surface of the appliance, since they will get hot.

54. To prevent overheating, the appliance should not

be installed behind of a decorative cover.

55. Turn off the appliance before removing the safeguards. After cleaning, install the safeguards according to instructions.

56. Cable xing point shall be protected.

57. WARNING: Don’t use oven and grill burners at same time.

58. Please don’t cook the food directly on the tray /

grid. Please put the food into or on appropriate tools before putting them in the oven.

59. Hot surface, leave for cooling before closing the cover.

Electrical Safety

1. Plug the appliance in a grounded socket protected by

a fuse conforming to the values specied in the technical specications chart.

2. Have an authorized electrician set grounding equipment. Our company shall not be responsible for the damages that shall be incurred due to using the product without grounding according to local regulations.

3. The circuit breaker switches of the oven shall be placed so that end user can reach them when the oven is installed.

4. The power supply cord (the cord with plug) shall not contact the hot parts of the appliance.

5. If the power supply cord (the cord with plug) is damaged, this cord shall be replaced by the manufacturer

or its service agent or an equally qualied personnel to

prevent a hazardous situation.

6. Never wash the product by spraying or pouring water on it! There is a risk of electrocution.

7. WARNING: To avoid electric shock, ensure that the device circuit is open before changing the lamp.

8. WARNING: Cut off all supply circuit connections before accessing the terminals.

9. WARNING: If the surface is cracked, turn off the appliance to avoid risk of electric shock.

10. Do not use cut or damaged cords or extension

cords other than the original cord.

11. Make sure that there is no liquid or humidity in

the outlet where the product plug is installed.

12. The rear surface of the oven also heats up when the oven is operated. Electrical connections shall not touch the rear surface, otherwise the connections may be damaged.

13. Do not tighten the connecting cables to the oven door and do not run them over hot surfaces. If the cord melts, this may cause the oven to short circuit and

even a re.

14. Unplug the unit during installation, maintenance, cleaning and repair.

15. If the power supply cable is damaged, it must be replaced by its manufacturer or authorized technical

service or any other personnel qualied at the same

level, in order to avoid any dangerous situation.

16. Make sure the plug is inserted rmly into wall socket to avoid sparks.

17. Do not use steam cleaners for cleaning the appliance, otherwise electric shock may occur.

18. An omnipolar switch capable to disconnect power supply is required for installation. Disconnection from power supply shall be provided with a switch or

an integrated fuse installed on xed power supply

according to building code.

19. Appliance is equipped with a type ‘’Y’’ cord cable.

20. Fixed connections shall be connected to a power

supply enabling omnipolar disconnection. For appliances with over voltage category below III, disconnection device

shall be connected to xed power supply according to

wiring code.

Gas Safety

1. This appliance is not connected to burning products

evacuation apparatus.This appliance must be connected and installed according to the installation regulations in force. Conditions regarding ventilation must be considered.

2. When a gas cooking appliance is used; humidity, heat and burning products are generated in the room. First of all, make sure the kitchen is well ventilated when operating the appliance and maintain natural ventilation openings or install a mechanical ventilation equipment.

3. After using the appliance heavily for en extended period of time, additional ventilation may be required. For example open a window or adjust a higher speed for mechanical ventilation, if any.

4. This appliance must be used only in well ventilated locations in accordance with the regulations in force. Please read the manual before installing or using this product.

5. Before positioning the appliance, make sure local network conditions (gas type and gas pressure) meets appliance requirements.

6. The mechanism cannot be run for longer than 15

seconds. If the burner is not on after 15 seconds, stop the mechanism and wait for at least one minute before trying to ignite the burner again.

7. All kinds of operations to be performed on gas installation must be performed by authorized and competent people.

8. This appliance is adjusted for natural gas (NG). If you have to use your product with a different gas type, you have to apply to authorized service for the conversion.

9. For proper operation, hood, gas pipe and clamp should be replaced periodically accordint to manufacturer recommendations and when required.

10. Gas should burn well in gas products. Well

burning gas can be understood from blue ame and continuous burning. If gas does not burn sufciently,

carbon monoxide (CO) can be generated. Carbon monoxide is a colourless, odourless and very toxic gas; even small amounts have lethal effect.

11. Ask your local gas supplies about the phone numbers for emergencies related to gas and the measures to be taken upon gas odour is detected.

What To Do When Gas Odour Is Detected

1. Do not use naked ame, and do not smoke.

2. Do not operate any electrical switch.

(For example: lamp switch or doorbell)

3. Do not use telephone or mobile phone.

4. Open the doors and windows.

5. Close all valves on the appliances that utilize gas

and the gas counters.

6. Call re brigade from a telephone outside the home.

7. Check all hoses and their connections against leaks.

If you still smell gas, leave the house and warn your neighbours.

8. Do not enter into the house until authorities clarify it is safe.

Intended Use

1. This product is designed for home use. Commercial

use of the appliance is not permitted.

2. This appliance may only be used for cooking purposes. It shall not be used for other purposes like heating a room.

3. This appliance shall not be used to heat plates under the grill, drying clothes or towels by hanging them on the handle or for heating purposes.

4. The manufacturer assumes no responsibility for any damage due to misuse or mishandling.

5. Oven part of the unit may be used for thawing, roasting, frying and grilling food.

6. Operational life of the product you have purchased is 10 years. This is the period for which the spare parts

required for the operation of this product as dened is

provided by the manufacturer.

Electrical Connection

1. Your oven requires 16 or 32 Ampere fuse according to the appliance’s

power. If necessary, installation by a qualied electrician is recommended.

2. Your oven is adjusted in compliance with 220-240V AC/380-415V

AC 50/60Hz.electric supply. If the mains are different from this specied

value, contact your authorized service.

3. Electrical connection of the oven should only be made by the sockets with earth system installed in compliance with the regulations. If there is no proper socket with earth system in the place where the oven will be

placed, immediately contact a qualed electrician. Manufacturer shall

never be responsible from the damages that will arise because of the sockets connected to the appliance with no earth system. If the ends of the electrical connection cable are open, according to the appliance type, make a proper switch installed in the mains by which all ends can be disconnected in case of connecting / disconnecting from / to the mains.

4. If your electric supply cable gets defective, it should denitely be replaced by the authorized service or qualed electricians in order to

avoid from the dangers.

5. Electrical cable should not touch the hot parts of the appliance.

6. Please operate your oven in dry atmosphere.

Electrical connection scheme

220-240V~50/60Hz

220-240V~50/60Hz 220-240V~50/60Hz

Live Phase

H05 VV-F 3G 4mm²

H05 VV-F 3G 4mm² H05 VV-F 5G 1.5mm² H05 VV-F 4G 1.5mm² H05 VV-F 3G 1.5mm²

400V 3N~50/60Hz 400V 2N~50/60Hz

380-415V 3N~50/60Hz 380-415V 2N~50/60Hz

Neutral Neutre

Earth Terre Erdung

H05 VV-F 5G 1.5mm²

Neutral Neutre

Earth Terre Erdung

H05 VV-F 4G 1.5mm²

Neutral Neutre

Earth Terre Erdung

220-240V~50/60Hz

H05 VV-F 3G 1.5mm²

Neutral Neutre

Earth Terre Erdung

Gas Connection WARNING: Before starting any work related with gas installation, turn off

gas supply. Risk of explosion.

Please operate your oven in dry atmosphere.

1. Fit the clamp to the hose. Push one of the hose until it goes to the end of the pipe.

2. For the sealing control; ensure that the buttons in the control panel are closed, but the gas cylinder is open. Apply some soap bubbles to the connection. If there is gas leakage, there will be foaming in the soaped area.

The oven should be using a well ventilation place and should be

install on at ground.

4. Re-inspect the gas connection.

5. When placing your oven to its location, ensure that it is at the counter

level. Bring it to the counter level by adjusting the feet if necessary.

6. Do not make gas hose and electrical cable of your oven go through theheated areas, especially through the rear side of the oven. Do not move gas connected oven. Since the forcing shall loosen the hose, gas leakage may occur.

7. Please use exible hose for gas connection.

For LPG connection;

1. For LPG (cylinder) connection, afx

metal clamp on the hose coming from LPG

Main Gas Pipe

cylinder. Afx an edge of the hose on hose

inlet connector behind the appliance by

Gasket

Hose Inlet Connector

Metal Clamp

pushing to end through heating the hose in boiled water. Afterward, bring the clamp towards end section of the hose and tighten it with screwdriver. The gasket and hose

Lpg Connection Hose

inlet connector required for connection is as the picture shown below.

WARNING: The regulator to be afxed on LPG cylinder should have 300

mmSS feature.

For natural gas connection;

WARNING: Natural gas connection should

Main Gas Pipe

Gasket Nut

Natural Gas Connection Hose

United kingdom type gas connection:

be done by authorized service. For natural gas connection, place gasket in the nut at the edge of natural gas connection hose. To install the hose on main gas pipe, turn the nut. Complete the connection by making gas leakage control.





1. Gasket

2. Adapter

3. Gas (safety) hose

4. Valve with 90° outlet

5. Connection piece

6. Gas supply pipe

l

6 5 /

WARNING: The gas hose must not be clamped, bent ar trapped or come into contact with hat parts of the product. There is the risk of explosion due to damaged gas hose.

Ventilation Of Room

The air needed for burning is received from room air and the gases emitted are given directly in room. For safe operation of your product, good room ventilation is a precondition. If no window or room to be utilized for room ventilation is available, additional ventilation should be installed. However, room has a door opening outside, it is no needed to vent holes.

Smaller than 5 m³ min. 100 cm²

Between 5 m³ - 10 m³ min. 50 cm²

Bigger than 10 m³ no need

In basement or cellar min. 65 cm²

Room Size Ventilating Opening

Gas hose passage way

Figure 1

Figure 2

Connect the appliance to the gas piping tap in shortest possible route and in a way that ensure no gas leakage will occur. In order to carry on a tightness and sealing safety check ensure that the knobs on the control panel are closed and the gas cylindir is open. WARNING: While performing a gas leakage check, never use any kind of lighter, match, cigarette or similar burning substance. Apply soap bubble on the connection points. If there is any kind of leakage then it will cause bubbling. While inserting the appliance in place ensure that it is on the same level with the worktop. If required adjust the legs inorder the make level with the worktop. Use the appliance on a level surface and in a well ventilated environment.

WARNING: Before placint the appliance, check that the local distribution conditions (gas type and pressure) conform to the product settings.

Reduced gas ow rate setting for hob taps

1. Ignite the burner that is to be adjustment and turn the knob to the

reduced position.

2. Remove the knob from the gas tap.

3. Use an appropriately sized screwdriver to adjust the ow rate adjustment

screw. For LPG (butane-pro pane) turn the screw clockwise. For the naturel gas, you should turn the screw counter- clockwise once.

“The normal length of a straight ame in the reduced position should

be 6-7 mm.“

4. If the ame is higher then the desired position, turn the screw clockwise.

If it is smaller turn anticolockwise.

5. For the last control, bring the burner both to higt-ame and reduced

positions and check whether the ame is on or off.

Depending on the type of gas tap used in your appliance the adjustment screw position may vary.

To adjust your oven acc. to the gas type, make the adjustment for

reduced ame carefully by turning with a small screwdriver as shown

below on the screw in the middle of the gas cocks as well as nozzle

changes. (gure 3 and 4)

Figure 3 Figure 4

Nozzle change operation

1. Please use driver with special head for removed and install nozzle as.

(gure 5)

2. Please remove nozzle (gure 6) from burner with special nozzle driver

and install new nozzle. (gure 7)

Figure 5

Figure 6

Figure 7

Removal of the Cathedral Burner:*

The burner protection sheet is xed with two screws. As shown in gure 8, use a screwdriver to remove it. As shown in gure 9, press the

spring clip in the direction of the arrow to remove the burner from the slot.

As shown in gure 10, remove the injector in the bearing with a socket

wrench. In order to re-place the burner, apply the removal process reversely.

Figure 8

Figure 9

Figure 10

Removal Of The Lower And Upper Burner And Installation Of The Injector To The Gas Oven

Removal of the upper burner:

With the help of a screw driver, remove the screw as shown in gure 11. As shown in gure 12, remove the burner from its place by pulling it to yourself. As shown in gure 13, remove the injector in the bearing with a

socket wrench. In order to re-place the burner, apply the removal process reversely.

Figure 11 Figure 12

Figure 13

Removal of the lower burner:

The lower burner door has been xed with two screws. As shown in gure 14, remove it with the help of a screw driver. Remove the door by pulling upwards as shown in gure 15. Remove the burner from its place by pulling it to yourself as shown in gure 16. As shown in gure 17, remove

the injector in the bearing with a socket wrench. In order to replace the burner, apply the removal process reversely.

Figure 14

Figure 16

Figure 15

Figure 17

INTRODUCTION OF THE APPLIANCE

1. Control panel

2. Top oven

3. Main oven

4. Large burner

5. Middle burner

6. Auxiliary burner

7. Wok burner *

8. Hot plate * (Ø145 mm or Ø185 mm)

Accesories

Deep tray *

Used for pastry, big roasts, watery foods. It can also be used as oil collecting container if you roast directly on grill with cake, frozen foods and meat dishes.

Tray / Glass tray *

Used for pastry (cookie, biscuit etc.), frozen foods.

Circular tray *

Used for pastry frozen foods.

Wire grill

Used for roasting or placing foods to be baked, roasted and frozen into desired rack.

Telescopic rail *

Trays and wire racks can be removed and installed easily thanks to telescopic rails.

In tray wire grill *

Foods to stick while cooking such as steak are placed on in tray grill. Thus contact of food with tray and sticking are prevented.

Tray handle *

It is used to hold hot trays.

Coffee pot support unit *

Can be used for coffee pot.

Technical Features Of Your Oven

Specication

Outside width 500 mm 600 mm

Outside depth 630 mm 630 mm

Outside height 900 mm 900 mm

Lower inside width Upper inside width 360 mm 460 mm

Lower inside depth Upper inside depth 400 mm 400 mm

Lower inside height Upper inside height 330 mm 180 mm 330 mm 180 mm

Lamp power 15-25 W

Upper heater 600 W 500 W 700 W 700 W

Lower heater 1000 W 800 W 1200 W 1000 W

Grill heater 1500 W 1400 W 2000 W 1400 W

Turbo heater 1800 W --- 2200 W ---

Supply voltage 220V-240V / 380-415V AC 50-60Hz

Hot plate 145 mm * 1000 W

50x60 60x60

Main Top Main Top

Hot plate 145 mm rapid * 1500 W

Hot plate 180 mm * 1500 W

Hot plate 180 mm rapid * 2000 W

WARNING: For the modication to be done by authorized service, this

table should be considered. Manufacturer may not be held responsible for

any problems rising because of any faulty modication.

WARNING: In order to increase the product quality, the technical

specications may be changed without prior notice.

WARNING: The values provided with the appliance or its accompanying documents are laboratory readings in accordance with the respective standards. These values may differ depending on the use and ambient conditions.

50x60 Double Oven

Burner

Specications

Wok

Burner

Rapid

Burner

Semi-Rapid

Burner

Auxiliary

Burner

G20,20 mbar G25,25 mbar

Gas Natural LPG

Injector 1,40 mm 0,96 mm

Gas ow 0,333 m³/h 254 g/h

Power 3,50 kW 3,50 kW

Injector 1,15 mm 0,85 mm

Gas ow 0,276 m³/h 211 g/h

Power 2,90 kW 2,90 kW

Injector 0,97 mm 0,65 mm

Gas ow 0,162 m³/h 124 g/h

Power 1,70 kW 1,70 kW

Injector 0,72 mm 0,50 mm

Gas ow 0,96 m³/h 69 g/h

G30,28-30 mbar

G31,37 mbar

Grill

Burner

Oven

Burner

Power 0,95 kW 0,95 kW

Injector 0,92 mm 0,60 mm

Gas ow 0,144 m³/h 109 g/h

Power 1,50 kW 1,50 kW

Injector 0,97 mm 0,65 mm

Gas ow 0,171 m³/h 131 g/h

Power 1,80 kW 1,80 kW

60x60 Double Oven

Burner

Specications

Wok

urner

Rapid

Burner

Semi-Rapid

Burner

Auxiliary

Burner

G20,20 mbar G25,25 mbar

Gas Natural LPG

Injector 1,40 mm 0,96 mm

Gas ow 0,333 m³/h 254 g/h

Power 3,50 kW 3,50 kW

Injector 1,15 mm 0,85 mm

Gas ow 0,276 m³/h 211 g/h

Power 2,90 kW 2,90 kW

Injector 0,97 mm 0,65 mm

Gas ow 0,162 m³/h 124 g/h

Power 1,70 kW 1,70 kW

Injector 0,72 mm 0,50 mm

Gas ow 0,96 m³/h 69 g/h

Power 0,95 kW 0,95 kW

G30,28-30 mbar

G31,37 mbar

Injector 0,92 mm 0,60 mm

Grill

Burner

Oven

Burner

Gas ow 0,144 m³/h 109 g/h

Power 1,50 kW 1,50 kW

Injector 0,97 mm 0,70 mm

Gas ow 0,190 m³/h 145 g/h

Power 2,00 kW 2,00 kW

WARNING: Diameter values written on the injector are specied without

a comma. For example; The diameter of 1,70 mm is specied as 170 on

the injector.

INSTALLATION OF YOUR OVEN

Check if the electrical installation is proper to bring the appliance in operating condition. If electricity installation is not suitable, call an electrician and plumber to arrange the utilities as necessary. Manufacturer shall not be held responsible for damages caused by operations performed by unauthorized persons.

WARNING: It is customer's responsibility to prepare the location the product shall be placed on and also to have the electrical installation prepared.

WARNING: The rules in local standards about electrical installations shall be followed during product installation.

WARNING: Check for any damage on the appliance before installing it. Do not have the product installed if it is damaged. Damaged products cause a risk for your safety.

Right Place for Installation and Important Warnings

Appliance feet should not stay on soft surfaces such as carpets. The

kitchen oor shall be durable to carry the unit weight and any other

kitchenware that may be used on the oven.

Appliance should be used with a clearance of minimum 400 mm over the upper hob surfaces, and 65 mm from side surfaces inside a kitchen furniture.

The appliance is suitable for use on both side walls, without any support, or without being installed in a cabinet. If a hood or aspirator will be installed above the cooker, follow the instructions of the manufacturer for height of mounting. (min. 650 mm)

400 mm min.

65mm min.

650mm min.

65mm min.

WARNING: The kitchen furniture near the appliance must be heat resistant.

WARNING: Do not install the appliance beside refrigerators or coolers. Heat radiated by the appliance increases the energy consumption of cooling devices.

WARNING: Do not use the door and/or handle to carry or move the appliance.

+ 65 hidden pages