Sima RCW-101,RCW-102,RCW-103,RCW-303,RCW-305 User Manual

DIGITAL RADIO

CONTROLLED WATCH

INTRODUCTION

Congratulations on your purchase of the
Sima RCW. Before you begin using the
RCW, please read this manual carefully and
keep this manual for further information.

ABOUT NIST

The RCW utilizes a highly sensitive radio
receiver to automatically set the time and
date. The National Institute of Standards
and Technology (NIST) measures each
second of time as 9,192,631,770 vibrations
of a Cesium 133 atom in a vacuum. The
measurement of the Cesium 133 atom is
accurate to one second every one million
years. The time is then transmitted from
Fort Collins, CO to the rest of the United
States (US). NIST is the official time used
by the US; it governs ship movements,
radio stations, and space flights. The RCW

also automatically adjusts for daylight

saving time, leap years, and leap
seconds. For more details about
the NIST Clock, please visit

www.NIST.gov

AUTOMATIC TIME SETTING

The RCW receives the NIST signal
automatically at 3:00AM every night. Once
the NIST signal is received the watch will
display the official U.S. time. The time and
date are set automatically for Eastern
Standard Time, which will need to be
adjusted if you are located in a different time
zone. If the signal cannot be received, the
RCW also can be set manually.

BEFORE USING THE RCW

The time zone that you are located in must
be selected. Setting the correct time zone
will allow the watch to set itself to the
correct time.

This watch should be set manually for the
first time. After that, the watch will
automatically adjust itself to maintain
accurate time.

SETTING THE TIME ZONE

The RCW will automatically set the time and
date when a NIST signal is received
successfully. However, you will still have to
set the correct time zone.
(Note: The RCW will not automatically
adjust to a new time zone if you are
traveling. You must change the time zone
setting to continue to keep the exact time.)

TIME ZONE SETTING

1. Press the MODE button three times and
the time zone will be displayed.

2. Press and hold the SET button for three
seconds or until the offset hours digits
begin to flash.

3. Press the RECEIVE button to increase or
press the LIGHT button to decrease the
hour-offset.

4. For standard time: (Eastern = -5) (Central
= -6) (Mountain = -7) (Pacific = -8)

5. Press the SET button once to return to
normal operation.

MANUAL TIME AND DATE SETTING

1. Press and hold the SET button for

three seconds and “12” or” 24” will blink
on the LCD.

Press the RECEIVE or LIGHT button to
change the setting from 12 to 24 or 24 to

12.

2. Press the SET button to advance to

the year setting.

Press the RECEIVE button to increase
the year or LIGHT button decrease the
desired year.

3. Press the SET button to advance to

the month setting.

Press the RECEIVE button to increase
the month or LIGHT button decrease the
desired month.

4. Press the SET button to advance to

the day of the month.

Press the RECEIVE button to increase
the day or LIGHT button to decrease the
day of the month.

5. Press the SET button to advance to

the day of week.

Press the RECEIVE button to increase

WATCH DISPLAY ICONS & BUTTONS

or the LIGHT button to decrease the day
of the week.

6. Press the SET button to advance to
hours.

Press the RECEIVE button to increase
the hour or the LIGHT button to
decrease the hour.

7. Press the SET button to advance to
minutes.

Press the RECEIVE button to increase
the minute or the LIGHT button to
decrease the minute.

8. Press the SET button to advance to
seconds.

Press the RECEIVE button or the
LIGHT button to reset the seconds to

“00”.

9. Press the SET button one more time
to return to normal operation.

BUTTONS AND FUNCTIONS

RECEIVE BUTTON

Pressing and holding the RECEIVE button
for five seconds activates the manual signal
receiver.
Pressing the RECEIVE button while in
manual setup will increase the digits
displayed on the LCD.
Press and hold the RECEIVE button to
increase the numbers at a faster rate.

LIGHT

Pressing the LIGHT button activates the
RCW backlight.
Pressing the LIGHT button while in manual
setup decreases the digits displayed on the
LCD.
Press and hold the LIGHT button to
decrease the numbers at a faster rate.

Online Product
Registration

http://www.simacorp.com

Models
RCW -101
RCW -103
RCW -303
RCW -305

1. AM/PM Indicator

2. Time Zone indicator

3. NIST Reception

4. Daylight Saving Time Indicator,

5. Day of Week

SETTING ALARM 1 & ALARM 2

The RCW has two alarms that can be
activated, AL1 and AL2. Pressing any
button will turn the alarm sound off once
activated. If no button is pushed, it will
automatically shut off after two minutes.

1) Press the MODE button once for
AL1, twice for AL2. The icon will
blink on the right side of the LCD.

2) Press and hold the SET button for
three seconds.The hour section of
the clock will begin blinking.

3) Press the RECEIVE button to
increase the hour or the LIGHT
button to decrease the hour.

4) Press the SET button to move to the
minute section of the clock.

5) Press the RECEIVE button to
increase the minute or the LIGHT
button to decrease the minute.

6) Press the SET button to advance to
the ON / OFF setting.

7) Press the RECEIVE button to set the
alarm to ON or OFF.

The icon for ON/OFF is located above
the second portion of the clock (on=ON,
oF=OFF).

8) The RCW will return to normal

operation in approximately 15 seconds.

SET

Pressing and holding the SET button for
three seconds enters the manual setup
mode. Different settings can be accessed
by pressing the SET button repeatedly .

MODE

Press the MODE button to enter the
alarm-setting menu.

EL (RCW-101 only)

Pressing the EL button will activate the
RCW backlight.

6. Month & Day

7. Hours: Minutes: Seconds

8. Alarm Indicators (AL1 + AL2)

9. EL - Light (RCW 101 only)

RECEIVE

SET

LIGHT

MODE

1

3

4

5

6

7

8

9

2

SIGNAL SEARCH

AUTOMATIC SEARCH

The RCW is designed to receive the NIST
signal automatically every night at 3:00AM.
The RCW will synchronize the time and
date with the NIST broadcast signal from
Fort Collins, CO. Note: You must set the

watch manually the first time for it to
auto synch during the night.

RECEPTION STATUS

If the NIST broadcast is successfully
received, the tower icon in the upper left
corner of the LCD will remain “on” all day.
The RCW will search for the signal again at
3:00AM.

If the reception was not successful, the
tower icon will be “off” which means that the
signal was not received in the past 24
hours. The RCW will automatically search
at 3:00AM everyday to update its time.
(Note: If the tower icon is not “on” in the
upper left corner, follow the instructions in
the MANUAL SIGNAL SEARCH section).

MANUAL SIGNAL SEARCH

When the tower icon is not present in the
upper left hand corner of the LCD the NIST
signal has not been received in the
previous 24 hours. The RCW searches for
the NIST transmission at 3:00AM every
night; which is the best time to receive the
signal. In the event that your RCW does
not have the tower icon displayed the
RECEIVE button can be pressed to attempt
to receive the signal.

1. Press and hold the RECEIVE button for
ten seconds to activate the signal
receiver. The tower icon will begin to

flash for up to ten minutes.

2. Do not press any buttons during the
manual signal search time.

SIGNAL STRENGTH

While the RCW is searching for the NIST
signal the tower will have rings that blink
around it to display the strength of the
signal being received. If the tower only
displays one ring around the tower icon, the
reception is poor in the area that you are
located. Move to a different area and
attempt to receive the signal again.

If the RCW is receiving a strong signal,
three rings will be displayed around the
tower icon. However, even when a strong
signal is received the RCW may not
automatically adjust the time due to RF
interference.

TIME CHANGE ADJUSTMENT

If the RCW receives the NIST signal at
3:00AM during the fall or springtime
change, it will automatically adjust to the
correct Daylight Saving Time.
During Daylight Savings time, each time the
signal is received, the “sun” icon will also
be displayed with the tower.

(Note: If you live in an area that does not
observe the daylight savings time change,
you will have to manually change the time
zone setting ahead one time zone as this
feature cannot be turned off).

TROUBLESHOOTING

At times the RCW may be placed in a
location where the NIST signal reception
becomes difficult due to interference.
Interference can be due to electrical
appliances such as televisions,
refrigerators, computers, fluorescent lamps,
or natural events such as thunderstorms. It
is important that you do not leave your
watch on a metallic surface and keep it
away from any sources of electromagnetic
interference.

If you continue to have unsuccessful NIST
signal reception, you may want to place
your watch near a window where it shows a
strong reception signal. The NIST signal
will usually be received at approximately
3:00AM when the signal reception is the
strongest.

CARE OF YOUR WATCH

- Never attempt to open the case or
remove the back-cover, as the watch
contains no components that are user
serviceable.

- Never swim with the RCW or submerge it
under water. Should water or
condensation appear in the watch, take
the RCW to a jeweler to check
immediately as water can corrode
electronic parts inside the watch.

- Avoid exposing the watch to long periods
of extreme temperatures. Normal
operation between of the RCW is 0° C­50° C/32° F-122° F.

LIMITED WARRANTY

Sima Products Corp. (“Sima”) warrants that if the accompanying
product proves to be defective to the original purchaser in material or
workmanship within 90 days from the original retail purchase, Sima
will, at Sima’s option, either repair or replace same without charge (but
no cash refund will be made).

What you must do to enforce Warranty:
You must deliver, mail or ship the product, together with both the

original bill of sale and this limited Warranty statement as proof of
warranty coverage to:

Sima Products Corp.
Attention: Customer Service
140 Pennsylvania Ave. Bldg. #5
Oakmont, PA 15139

Sima Products Corporation shall have no liability for any damages due to
lost profits, loss of use or anticipated benefits, or other incidental,
consequential, special or punitive damages arising from the use of, or
the inability to use, this product, whether arising out of contract,
negligence, tort or under any warranty, even if Sima Products Corporation
has been advised of the possibility of such damages. Sima Products
Corporation’s liability for damages in no event shall exceed the amount
paid for this product. Sima Products Corporation neither assumes nor
authorizes anyone to assume for it any other liabilities.

To receive special offers and discounts, register online at
www.simacorp.com.

© 2005 Sima Products Corporation PN 21726

- The RCW is designed to withstand
impact under normal use only. The
RCW is not designed for rough usage
or to be dropped onto hard surfaces.

- Keep your RCW away from the strong
electromagnetic fields and static
electricity.

- Clean the RCW with a soft cloth only.

SERVICE

The RCW is only to be opened by an
experienced jeweler. The user should
never open the RCW.

BATTERY REPLACEMENT

The RCW requires CR2025 battery. Y our
RCW is a delicate instrument and requires
special tools for changing the battery;
therefore, Sima strongly recommends that
qualified personnel only change the battery.
Automatic reception of the NIST signal will
activate once the battery is replaced.