SilverStone ST50F-ES230 User Manual

lssue date: July, 2012
NO.G11216800
STRIDER ESSENTIAL SERIES
SST-ST50F-ES230
Power for everything you need
High efficiency greater than 80% (Max. up to 85%)
24/7 continuous power output with 40 operating temperature
Class-leading single +12V rail
Multiple protection circuitry
PCI-E 8pin and PCI-E 6pin connector support
Silent running 120mm fan with 18dBA
SPECIFICATION
SilverStone Strider Essential
ST50F-ES230
ATX12V Switching Power Supply
STRIDER ESSENTIAL SERIES
2.3 Max. Input AC Current
Max. Input Current Measuring Range
4.0A 207-253 Vrms
2.4 Inrush Current
The power supply must meet inrush requirements for any rated AC voltage, during turn on at any phase of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF cycling of AC, and over the specified temperature range. The peak inrush current shall be less than the ratings of its critical components (including input fuse, bulk rectifiers, and surge limiting device).
With Active PFC
PS/2
1.General
1.1 Scope
This specification defines the performance characteristics of a single phase 500 watts, 5 output power supply. This specification also defines worldwide safety and electromagnetic compatibility requirements for the power supply which is intended for use in computer products.
2.Input Characteristics
2.1 Input Voltage
Nominal Voltage Voltage Variation Range 230 Vrms 207 - 253 Vrms
2.2 Input Frequency
Nominal Frequency Frequency Variation Range 50 Hz 47 Hz to 63 Hz
2.5 Efficiency
SST-ST50F-ES230 provides an efficiency of >80% when measured at full load under 230V/50Hz condition.
3.Output characteristics
3.1 Normal Operation Output
Output Voltage Load MIN Range MAX Regulation Ripple P-P Max.
1. +5V
2. +3.3V
3. +12V
5. -12Vs
6. +5V
Maximum continuous total DC output power should not exceed 500W. Maximum continuous combined load on +3.3VDC and +5VDC outputs shall not exceed 120W.
NOTE: Noise test should be measured with 20 MHz bandwidth frequency oscilloscope. The output terminal shall add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0.1uF.
0.2A
0.1A
0.1A
0.0A
0.0A
20.0A
24.0A
34.0A
0.3A
2.5A
±5% ±5% ±5%
±10% ±5%
120mV 120mV 200mV
200mV 100mV
* The power supply must operate at above frequency with 207 - 253VACrms input voltage range.
01
02
STRIDER ESSENTIAL SERIES
4.2.1 Under voltage protection
3.2 Remote On/Off Controlled mode
The PSON# signal is required to remotely turn on/off the power supply, PSON# is an active low signal that turns on the output power rails. When this is not pulled low by the system, or left open, the outputs (except the +5VSB) turn off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply.
TTL level "H" 2.0 V - 5.25 V "L" 0.0 V – 1.0 V
3.3 Regulation
The cross regulation defined as follows, the output regulation should be within the specified range.
Load
Light Load.
Typical Load
Full Load
+5V
2.50A
6.25A
12.49A
+3.3V
3.00A
7.49A
14.99A
+12V1
6.22A
15.54A
31.08A
-12V
0.06A
0.14A
0.28A
+5Vsb
0.47A
1.17A
2.33A
3.4 Rise Time
DC output rise time is less than 20 mS at nominal line and full load.
3.5 Hold-up Time
DC +5V output maintains at least 8mS after power off which hold within para 3.1 under 230V/50Hz condition.
3.6 5VSB
5VSB is requierd for the implementation of PS-ON described above. 5VSB is a standby voltage that may be used to power circuits that require power input during the powered-down state of all power rails. The 5 VSB pin should deliver 5V ± 5% at a minimum of 2.5 A for PC board circuits to operate. Conversely, PC board should draw no more than 2.5A maximum form this pin. This power may be used to operate circuits such as soft power control.
3.7 PG-OK
PG-OK is a power good signal and should be asserted high by power supply to indicate that the +5 VDC and +3.3 VDC outputs are above the under-voltage thresholds of the power supply. When this signal is asserted high, there should be sufficient mains energy stored by the converter to guarantee continuous power operation within specification. Conversely, when either the +5VDC or the +3.3VDC output voltage falls below the under-voltage threshold, or when mains power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed, PG-OK should be deasserted to a low state. See Figure 1 for a representation of the timing characteristics of the PG-OK,PS-ON, and germane power rail signals.
3.8 3.3V Sense
A default 3.3V sense line should be implemented pin 13 of the connector.
3.9 Capacitive Load
The power supply should be able to power up and operate normally with the following capacitances simultaneously present on the DC outputs.
Output
+5V
+12V
+3.3V
-12V
+5VS
Capacitive load (uF)
10,000 10,000 10,000
350 350
4.Protection
4.1 Input Protection
In primary circuit of the power supply , a protected fuse is inserted. Only internal fault of the power supply will cause the fuse blown. Any overload or short circuit at DC output will keep from fuse brown or fire hazard.
03
4.2 Output Protection
4.2.1 Under voltage protection The +5V/+3.3V DC output are protected against the under voltage condition . range value can't be exceed 3.3~3.7V at 5V terminal and 2.0~2.4V at 3.3V.
04
4.2.2 Over Voltage Protection
4.2.2 Over Voltage Protection
4.2.3 Over Power Protection
4.2.4 Short Circuit Protection
6.1.1 Operating
6.1.2 Storage
The +5V/+12V/+3.3V DC output are protected against the over voltage condition . Maximum value can't be over 6.5V at 5V terminal and 15.5V at 12V, 4.3V at 3.3V.
4.2.3 Over Power Protection The power supply can be used electronic circuit to limit the output current against exceeding 60% of surge output power or protected against excessive power delivery since short circuit of any output or over total power at high line.
Frequency
5-55-10 Hz
Duration
30 minutes
7. Conducted EMI
FCC,CE
STRIDER ESSENTIAL SERIES
Amplitude
0.35 mm
4.2.4 Short Circuit Protection Short circuit placed on +5V,+12V,+3.3V,-12V will latch off. +5VSB will auto-recovery.
5.Start Stability
5.1 No Load Start
When power is applied to SST-ST50F-ES230 with no load connected or under minimum load connected, neither damage to power supply nor hazards to users will occur.
5.2 Cold Start
The power supply shall operate properly when first applied at normal input voltage and or so maximum load after 4 hours storage in 0 environment.
6.Environments
6.1 Temperature and Humidity
6.1.1 Operating Temperature 0 to 40 Relative Humidity 20 to 90 %
6.1.2 Storage Temperature -40 to 70 Relative Humidity 20 to 95 % noncondensing
6.2 Altitude
The power supply can operate normally at any altitude between 0 to 10000 feet.
8. Product Safety
8.1 Safety Requirement
TUV,CB
8.2 Leakage Current
The AC leakage current is less than 3.5mA when the power supply connect to 253Vac/50Hz .
8.3 Insulation Resistance
The insulation resistance should be not less than 30M ohm after applying of 500VDC for 1 minute.
8.4 Dielectric Voltage Withstand
The power supply shall withstand for 1 minute without breakdown the application of a 60Hz 1500V AC voltage applied between both input line and chassis (20mA DC cut-off current). Main transformer shall similarly withstand 3000Vac applied between both primary and secondary windings for a minimum of one minute.
9. Power Good Signal
A TTL compatible signal for the purpose of initiating an orderly start-up procedure under normal input operating conditions. During power up, this signal is asserted ( low ) until +5V is under regulation and AC reaches min. line specification range. After all voltage are going appropriate level, the system may have a turn on delay of 100mS, but no greater than 500mS. During power off the signal should go to low level before +5V is out of regulation. The low level is 0 to 0.8V and high level is 4.75 to 5.25V. The " Power Good "signal can drive up to 6 standard TTL loads.
6.3 Vibration and Shock
Sweep and resonance search for each of X,Y,Z, axis at the sweep. RATE of 1/OCTAVE/Min.
05
06
STRIDER ESSENTIAL SERIES
Time Diagram Figure 1
AC
+5Vs
PS-ON/OFF
+5V O/P
T1
Power Good
* T1 : Turn on time ( 2 sec. Max.) * T2 : Rise time ( 20mS Max.) * T3 : Power good turn on delay time ( 100 < T3 < 500 mS ) * T4 : Switch on time (0.5 sec. Max.) * T5 : Power good turn off delay time ( 1.0 mS Min.) PS-ON/OFF * T6 : Power hold-on time ( 8 mS Min.) * Power on-off cycle : When the power supply is turned off for a minimum of 2.0 sec. and turn on again, the power good signal will be asserted.
AC ON AC OFF
POWER ON POWER ON
4.75V
0.25V
T4 T3
T2
4.75V
T5
T6
12. Harmonics
The product shall meet requirement for EN61000-3-2 & EN61000-3-3 :2003 standard of class D, test at 230Vac 50Hz.
13.Power Factor
The power supply with active power factor correction, and meet the EN61000-3-2 standards, The power factor is greater than 0.9 at 230V/50Hz, Max. load.
14. Mechanical Requirements
14.1 Physical Dimension
150 mm (W) × 86 mm (H) × 140mm (D)
14.2 Connectors M/B 24PIN connector
10. MTBF
The MTBF of the power should be 50,000 hours min
11. Burn-In
11.1 Input Voltage
Applying 220Vac for230Vac model.
11.2 Test Condition
Applying 75% loads for the power supply in 40 (+/-5) oC chamber for 4 hours.
07
EPS 12V 8PIN connector
Signal
Yellow Yellow Yellow Yellow
+12V +12V +12V +12V
Pin
5 6 7 8
Pin
1 2 3 4
Signal
COM COM COM COM
Black Black Black Black
08
STRIDER ESSENTIAL SERIES
ATX 12V 4PIN
Black Black
Signal
GND GND
Pin
1 2
Pin
3 4
Signal
+12V +12V
Yellow Yellow
4PIN peripheral connector (HDD) 4PIN floppy connector (FDD)
Yellow Black Black Red
Signal
+12V COM COM
+5VDC
Pin
1 2 3 4
Pin
1 2 3 4
Signal
+5VDC
COM COM +12V
Red Black Black Yellow
SATA connector
Signal Pin
Orange
Black
Red
Black
Yellow
+3.3V 5
COM 4
+5V 3 COM 2 +12V 1
Warranty Information
This product has a limited 3 year warranty in North America, Europe, and Australia. For information on warranty periods in other regions, please contact your reseller or SilverStone authorized distributor.
Warranty terms & conditions
1. Product component defects or damages resulted from defective production is covered under warranty. Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology’s jurisdiction. a) Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other inappropriate actions. b) Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc…) c) Product is not disassembled, modified, or fixed. Components not disassembled or replaced. d) Warranty mark/stickers are not removed or broken. Loss or damages resulted from conditions other than ones listed above are not covered under warranty.
2. Under warranty, SilverStone Technology’s maximum liability is limited to the current market value for the product (depreciated value, excluding shipping, handling, and other fees). SilverStone Technology is not responsible for other damages or loss associated with the use of product.
3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no circumstances will SilverStone Technology be liable for damages in connection with the sale, purchase, or use including but not limited to loss of data, loss of business, loss of profits, lsof use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty, contract or negligence, even if SilverStone Technology has been advised of the possibility of such damages.
4. Warrant y covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second hand purchaser.
5. You must provide sales receipt or invoice with clear indication of purchase date to determine warranty eligibility.
6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone authorized distributors or SilverStone http://www.silverstonetek.com. Please note that: (i) You must provide proof of original purchase of the product by a dated itemized receipt; (ii) You shall bear the cost of shipping (or otherwise transporting) the product to SilverStone authorized distributors. SilverStone authorized distributors will bear the cost of shipping (or otherwise transporting) the product back to you after completing the warranty service; (iii) Before you send the product, you must be issued a Return Merchandise Authorization (“RMA”) number from SilverStone. Updated warranty information will be posted on SilverStone’s official website. Please visit http://www.silverstonetek.com for the latest updates.
Additional info & contacts
8PIN PCI Express connector
Signal Pin Pin Signal
Yellow Yellow Yellow
+12V 1 5 COM Black +12V 2 6 COM Black +12V 3 7 COM Black
Black sense1 COM 4 8 COM Black
6PIN PCI Express connector
Signal Pin Pin Signal
Yellow Yellow Yellow
09
+12V 1 4 COM Black +12V 2 5 COM Black +12V 3 6 COM Black
For North America (usasupport@silverstonetek.com) SilverStone T echnology in North America may repair or replace defective product with refurbished product that is not new but has been functionally tested. Replacement product will be warranted for remainder of the warranty period or thirty days, whichever is longer. All power supplies should be sent back to the place of purchase if it is within 30 days of purchase, after 30 days, customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the “USA RMA form for end-users” form from the below link and follow its instructions.
http://silverstonetek.com/contactus.php
For Australia only (support@silverstonetek.com)
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please refer to above “Warranty terms & conditions” for further warranty details.
SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. + 886-2-8228-1238 (standard international call charges apply)
For Europe (support.eu@silverstonetek.de) For all other regions (support@silverstonetek.com)
10
Loading...