SilverStone PT15B-H1D1, PT15B-D2, PT15B-H2, PT15B-H1D2 User Manual

NO.G11221091

Premium aluminum case
for Intel NUC motherboards

PT15

Compatible with most Intel NUC motherboards

Premium aluminum construction & SilverStone styling

Pre-assembled WIFI antenna and Bluetooth for ease of deployment

Super small design at 130mm x 110mm x 41mm

Includes VESA MISD-75 mounting bracket

Supports DIN rail mounting

2

3

Warranty Information

This product has a limited 3 year warranty in North America, Europe, and Australia.
For information on warranty periods in other regions, please contact your reseller or SilverStone authorized distributor.

1. Product component defects or damages resulted from defective production is covered under warranty.
Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology’s jurisdiction.
a) Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other inappropriate actions.
b) Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc…)
c) Product is not disassembled, modified, or fixed. Components not disassembled or replaced.
d) Warranty mark/stickers are not removed or broken.
Loss or damages resulted from conditions other than ones listed above are not covered under warranty.

2. Under warranty, SilverStone Technology’s maximum liability is limited to the current market value for the product (depreciated value, excluding
shipping, handling, and other fees). SilverStone Technology is not responsible for other damages or loss associated with the use of product.

3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no circumstances will SilverStone
Technology be liable for damages in connection with the sale, purchase, or use including but not limited to loss of data, loss of business, loss of
profits, loss of use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty,
contract or negligence, even if SilverStone Technology has been advised of the possibility of such damages.

4. Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second hand
purchaser.

5. You must provide sales receipt or invoice with clear indication of purchase date to determine warranty eligibility.

6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone authorized distributors or SilverStone
http://www.silverstonetek.com.
Please note that: (i) You must provide proof of original purchase of the product by a dated itemized receipt; (ii) You shall bear the cost of shipping
(or otherwise transporting) the product to SilverStone authorized distributors. SilverStone authorized distributors will bear the cost of shipping
(or otherwise transporting) the product back to you after completing the warranty service; (iii) Before you send the product, you must be issued a
Return Merchandise Authorization (“RMA”) number from SilverStone. Updated warranty information will be posted on SilverStone’s official website.
Please visit http://www.silverstonetek.com for the latest updates.

Warranty terms & conditions

Additional info & contacts

For North America ([e-mail])
SilverStone Technology in North America may repair or replace defective product with refurbished product that is not new but has been functionally tested.
Replacement product will be warranted for remainder of the warranty period or thirty days, whichever is longer. All products should be sent
back to the place of purchase if it is within 30 days of purchase, after 30 days, customers need to initiate RMA procedure with SilverStone Technology
in USA by first downloading the “USA RMA form for end-users” form from the below link and follow its instructions.

http://silverstonetek.com/contactus.php
For Australia only ([e-mail])

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Please refer to above “Warranty terms & conditions” for further warranty details.

SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. + 886-2-8228-1238
(standard international call charges apply)

For Europe ([e-mail])
For all other regions ([e-mail]

)

NUC

NEXT UNIT OF COMPUTING

PT15B-H1D1

PT15B-D2

PT15B-H1D2

PT15B-H2

VESA-Montagehalterung mit vier
Schrauben an der Rückseite des Monitors
befestigen.

Fije el bracket de la montura VESA con
cuatro tornillos a la parte trasera del
monitor.

Fissare il supporto VESA con quattro viti
alla parte posteriore del monitor.

Secure VESA mount bracket with four
screws on rear of monitor.

VESAマウントブラケットをモニタ後部
にネジ4本で固定します。

С помощью четырех винтов закрепите
монтажный кронштейн VESA на задней
панели монитора.

將VESA背板以四顆螺絲鎖固於螢幕後方。

将VESA背板以四颗螺丝锁固于屏幕后方。

네 개의 나사를 사용하여 VESA 장착
브래킷을 모니터의 후면에 고정합니다.

Vissez la console de montage VESA avec
les quatre vis à l'arrière de l'écran.

PT15 an der VESA-Halterung ausrichten
und drücken; dann zum Abschließen der
Installation nach unten drücken.

Alinee y presione la PT15 contra el bracket
VESA, luego presione hacia abajo para
completar la instalación.

Allineare e spingere PT15 ne supporto
VESA, quindi spingere verso il basso per
completare l'installazione.

Align and push PT15 into the VESA
bracket, than push downward to complete
installation.

PT15をVESAブラケットに合わせて押
さえ、下方に押して装着は完了です。

Выровняйте и установите PT15 в
кронштейн VESA, затем нажмите
вниз для окончательной установки.

先將PT15對齊VESA背板後推入，
再往下扣住背板即可完成安裝。

先将PT15对齐VESA背板后推入，
再往下扣住背板即可完成安装。

PT15를 VESA 브래킷에 맞춰 정렬하여
밀어 넣은 후 아래로 눌러 설치를 완료합니다.

Alignez et poussez le PT15 dans la
console VESA, puis poussez vers le bas
pour terminer l'installation.

VESA mount installation procedure

Motherboard installation procedure

1

2

3

4

5

6

7

1

Zwei Schrauben an der Vorder- und
Rückseite des PT15 lösen.

Afloje dos tornillos de la parte frontal
y trasera de la PT15

Allentare le due viti dal pannello anteriore
e posteriore di PT15.

Loosen two screws from the front
and rear of PT15

PT15の前部と後部からネジ2本を外
します。

Отверните два винта на передней
и задней панели корпуса PT15

將PT15後背板兩顆平頭螺絲卸除。

将PT15后背板两颗平头螺丝卸除。

PT15의 전면과 후면에서 2개의 나사를
풉니다.

Dévissez les deux vis à l'avant et à
l'arrière du PT15

Vier Schrauben und Fußständer von der
Unterseite des PT15 lösen, dann unteres
Fach herausziehen.

Afloje cuatro tornillos y soportes de la
parte inferior de la PT15, luego tire de la
bandeja inferior.

Allentare le quattro viti ed i piedini dal
pannello inferiore di PT15, quindi estrarre
il cassetto inferiore.

Loosen four screws and foot stands
from the bottom of PT15 then pull out
the bottom tray.

PT15の底部からネジ4本とフットスタンド
4個を外してから、底部トレイを引き出し
ます。

Отверните четыре винта и стойки с нижней
части корпуса PT15 и извлеките нижний лоток.

將底部四顆螺絲與腳墊卸除，並將底板抽出。

将底部四颗螺丝与脚垫卸除，并将底板抽出。

4개의 나사를 풀어 PT15의 하단에서 바닥
받침대를 제거한 후 하단 트레이를 빼냅니다.

Dévissez les quatre vis et les supports
de pieds en dessous du PT15, puis retirez
le plateau inférieur.

Installiertes unteres Fach wieder in das
Gehäuse einsetzen.

Inserte la bandeja inferior instalada de
vuelta en la carcasa.

Inserire nel telaio il cassetto inferiore con
la scheda madre installata.

Insert the installed bottom tray back into
the case.

取り付けられたマザーボードをケ
ースに戻します。

Установите нижний лоток на
место в корпус.

將組裝好的底板滑入機殼內。

将组装好的底板滑入机壳内。

설치된 하단 트레이를 케이스에
도로 끼웁니다.

Replacez le plateau inférieur dans le
boîtier.

Zwei Schrauben wieder an der Rückseite
des Gehäuses befestigen.

Fije de nuevo dos tornillos en la parte
trasera de la carcasa.

Fissare di nuovo le due viti sul pannello
posteriore del telaio.

Secure two screws back to the rear
of the case.

ケースにネジ2本を戻します。

Заверните два винта на задней
панели корпуса.

鎖上後面板與兩顆平頭螺絲

锁上后面板与两颗平头螺丝

2개의 나사를 케이스의 후면에
도로 고정합니다.

Vissez de nouveau les deux vis à l'arrière
du boîtier.

Vier Schrauben und Fußständer wieder
an der Unterseite des PT15 befestigen.

Fije cuatro tornillos y los soportes de
nuevo en la parte inferior de la PT15.

Fissare di nuovo le quattro viti ed i piedini
sul pannello inferiore di PT15.

Secure four screws and foot stands back
to the bottom of PT15.

PT15の底部に4個のフットスタン
ドとネジ4本を戻します。

Заверните четыре винта и стойки
в нижней части корпуса PT15

將四顆螺絲與腳墊裝回PT15

将四颗螺丝与脚垫装回PT15

4개의 나사를 사용하여 PT15의
하단에 바닥 받침대를 도로
고정합니다.

Vissez les quatre vis et les supports de
pieds en dessous du PT15.

Vibrationsfeste Gummidichtung mit zwei
Schrauben an der Unterseite des PT15
anbringen.

Fije la junta de goma anti vibración con
dos tornillos en la parte inferior de la PT15.

Fissare le guarnizioni di gomma anti­vibrazione con due viti sulla parte inferiore
di PT15.

Secure anti-vibration rubber gasket
with two screws on the bottom of PT15.

PT15底部に防振ゴムパッキングをネ
ジ2本で固定します。

С помощью двух винтов закрепите
антивибрационную резиновую прокладку
на нижней части корпуса PT15.

將防震膠墊以兩顆螺絲鎖固於PT15底部。

将防震胶垫以两颗螺丝锁固于PT15底部。

두 개의 나사를 사용하여 진동 방지 고무
가스켓을 PT15의 하단에 고정합니다.

Vissez la rondelle en caoutchouc anti­vibration avec les deux vis au bas du
PT15.

An diesem Punkt WLAN-Antennenkabel
an WLAN-Modul anschließen, falls das
Motherboard dies unterstützt.

Conecte el cable de antena WiFi al
módulo WiFi en este momento si la
placa base lo soporta.

A questo punto, collegare il cavo
dell'antenna WiFi al modulo WiFi, se la
scheda madre lo supporta.

Connect WiFi antenna cable to the WiFi
module at this point if the motherboard
supports it.

マザーボードがWiFi対応であれば、
この時点でWiFiアンテナケーブルを
WiFiモジュールに接続します。

Подключите кабель антенны WiFi к
модулю WiFi, если системная плата
поддерживает эту функцию.

若有無線網卡，需先接上天線導線。

若有无线网卡，需先接上天线导线。

이 때 메인보드가 WiFi 모듈을 지원하는
경우 WiFi 안테나 케이블을 WiFi 모듈에
연결합니다.

Branchez ensuite le câble de l'antenne
Wi-Fi sur le module Wi-Fi si la carte mère
le prend en charge.

Motherboard am unteren Fach installieren
und mit vier Schrauben befestigen.

Instale la placa base en la bandeja inferior
y fíjela con cuatro tornillos.

Installare la scheda madre nel cassetto
inferiore e fissarla con quattro viti.

Install motherboard onto the bottom tray
and secure it with four screws.

マザーボードを底部トレイに取り付け、
ネジ4本で固定します。

Установите системную плату в нижний
лоток и закрепите ее четырьмя винтами.

將主機板用四顆螺絲鎖在底板上。

将主板用四颗螺丝锁在底板上。

메인보드를 하단 트레이에 설치하고 4개의
나사를 사용하여 이를 고정합니다.

Installez la carte mère sur le plateau
inférieur, puis fixez-le avec quatre vis.

VESA mount installation procedure