SilverStone LCD 13 User Manual

Disassemble Chart

Product Overview

Specification:

NO:11400110

SST-LC13

Material: Aluminum front panel, 1.0mm SECC body
Color: Black & Silver
Motherboard:

Extended ATX*, ATX, Micro ATX

Drive Bay: External - 5.25" x 2 / 3.5" x 2
Internal - 3.5" x 2
Cooling System: Front - 92mm intake, 2100rpm, 21dBA
Rear - 2 x 60mm exhaust, 3000rpm, 25dBA
Expansion Slot: 7
Front I/O Port:

USB2.0 x 2, IEEE1394 x 1, audio x 1, MIC x 1

Power Supply: Optional standard PS2 (ATX)
Net Weight: 9 kg
Dimension: 430 mm (W) x 163 mm (H) x 430 mm (D)

February , 2005

cification:

T-LC1

3

terial:

Aluminum front

pan

el,

1.0mm SECC bod

y

b

3.5 BAY * 2

3.5 BAY * 1 (HIDDEN)

STANDARD ATX M/B

9225 FAN

FRONT IO (USB * 2+1394 + AUDIO)

POWER SW

DOOR

5.25 BAY * 2

5.25 BAY * 2

PS2 POWER SUPPLY

6025 FAN * 2

TOP PANEL

3.5 BAY * 1 ( HIDDEN )

LC13

* LC13 has mounting holes for extended ATX motherboards, but it does not fully support all available extended ATX motherboards
on the market. The use of extended ATX motherboard will also require the removal of 3.5" drive bay

ation

1. Unscrew four case screws to remove case
cover

13. Line up optical drive with the front panel
and secure it with screws

19. Use included 3pin to 4pin adapter to
connect a case fan if your motherboard
does not support enough 3pin fan headers

20. After installing all other system components,
place the case cover back onto the case
and secure with screws to complete installation

14. After optical drives are installed, place
the 3.5" drive bracket back into the case
and secure with screws

15. A second 3.5" drive bracket is located
beneath the 5.25" drive bays with room for
one more hard drive. It can be taken out
of the case easily with a screw removed

16. After installing hard drive into the bracket,
slide it back underneath the 5.25" drive bays

17. Secure reinstalled bracket with screw 18. For extra EMI protection, route front panel
cables through the included wire ring

7. Remove front 3.5" drive bay covers as
needed depending on how many external

3.5" drive bay device is required

8. Use #6-32 x 6 screws to install hard
drive into the 3.5" drive bracket

9. Install floppy drive or other 3.5" drive bay
device into the drive bracket. Use the
drive bay cover as a guide for lining up
the drive or installed device

10. If one of the external 3.5" drive bay isn't
used, the extra space can be used for
an additional hard drive

11. Optical drive installation- Remove screws

holding the 5.25" drive bay cover

12. Insert optical drive into the 5.25" drive bay
from the front of the case

2. Check for included accessories (screw bag,
3pin to 4pin adapater, and EMI wire ring)

3. Power Supply Installation- Insert power
supply into the case, secure with four
#6-32 x 6 screws

6. Hard Drive and 3.5" bay Installation­ Remove 3.5" drive bracket from the case

5. Place motherboard into the case and

secure with screws

4. Motherboard Installation- Insert included
motherboard standoffs into holes on the
bottom of the case that will lineup with
your motherboard