1
Instruction Manual
BS Series
NOTE: Owner/Operator must read and understand this instruction manual
before using the lift table.
RevB: 02/2009
2
Operation and Service Manual
BEFORE OPERATING THE LIFT TABLE, READ THIS MANUAL CAREFULLY AND UNDERSTAND
COMPLETELY. KEEP THIS MANUAL ON FILE FOR FUTURE REFERENCE. IF THIS IS LOST, PLEASE
CONTACT YOUR LOCAL SUPPLIER FOR A NEW COPY. ALSO, IF THE WARNING/CAUTION DECAL ON
THE UNIT IS LOST, PLEASE CONTACT YOUR LOCAL SUPPLIER FOR A NEW DECAL.
NOTE: On this manual, WARNING means the danger which can lead to death or serious injury. CAUTION
means the danger which can lead to slight injury or property damage.
1. WARNING
1.DO NOT put foot or hand in scissors mechanism.
2.DO NOT allow other person to stand in front of or behind lift table when it is moving.
3.DO NOT move lift table when table is in raised position. Load could fall down.
4.DO NOT enter under table.
5.DO NOT overload lift table.
6.DO NOT put foot in front of rolling wheels. Injury could result.
7.WATCH difference and hardness of floor level when moving lift table. Load could fall down.
8.DO NOT use lift table on slope or inclined surface, lift table may become uncontrollable and create danger.
9.DO NOT lift people. People could fall down and suffer severe injury.
2. CAUTION
1.Read this operation manual carefully and understand completely operating lift table. Improper operation
could create danger.
2.This lift table is a movable lifter designed to lift or lower rated load on table. NO NOT use lift table for other
purpose than its intended use.
3.DO NOT allow person to operate lift table who does not understand its operation.
4.DO NOT lower table too fast. Load could fall down and create danger.
5.KEEP watching the condition of load. Stop operating lift table if load becomes unstable.
6.Byake lift table when sliding load on of off table.
7.DO NOT side or end load. Load must be distributed on at least 80%of table area.
8.DO NOT use lift table with unstable, unbalanced loosely stacked load.
9.Practice maintenance work according to service instructions.
10. DO NOT modify lift table without manufacturer’s written consent.
11. REMOVE load from table and use safety stopper to prevent table from lowering when servicing lift table.
12. This lift table is not designed to be water resistant. Use lift table under dry condition.
3. DAILY INSPECTION
Daily inspection is effective to find the malfunction or fault on lift table. Check lift table on the following points
before operation.
3
CAUTION
DO NOT use lift table if any malfunction or fault is found.
(1) Check for scratch, bending or cracking on the lift table.
(2) Check if there is any oil leakage from the cylinder.
(3) Check the vertical creep of the table.
(4) Check the smooth movement of the wheel.
(5) Check the function of brake.
(6) Check if all the bolt and nuts are tightened firmly.
4. OPERATING LIFTTABLE
4-1. How to use the brake.
CAUTION
Brake lift table when not moving it in order to prevent sudden movement.
The brake is equipped with the swivel caster on the right side.
(1) Braking the wheel, press the brake pedal.
(2) Releasing the brake, lift up the brake pedal.
4-2 Lifting the table
WARNING
1. DO NOT overload lift table, stay within its rated capacity.
2. DO NOT side end load must be distributed on at least 80% of table area.
Press the lifting pedal several times the until the table reaches the desired position.
The table does not elevate after reaching the highest position even if the lifting pedal is pressed.
The table lowers slightly after reaching the highest position.
MAXIMUM CAPACITY OF TABLE
BS15
BS25
BS50
BS75
BS100
BS30D
BS50D
BS80D
150KG
250KG
500KG
750KG
1000KG
300KG
500KG
800KG
4
NOTE:
The hydraulic cylinder is designed to hold table. As is the nature of the hydraulic system, table lowers very
slowly over and extended period of time, Please note the table does not stay at the same position
ionindefiinitely.
4-3. Lowering table
WARNING
DO NOT put foot or hand in scissors mechanism.
Pull the lowering down and table lowers.
5. Specifications
Model
Capacity
(kg)
Table
(mm)
Table
Height(mm)
Stroke
L×W×H
(mm)
Pedal to top.
(approx. times)
Wheel
(mm)
φ
Weight
(kg)
BS15
150
700×450
225-760
535
1000×450×950
16
100
41
BS25
250
830×500
335-915
580
1100×500×1010
25
125
78
BS50
500
1010×520
430-1000
570
1130×520×1185
44
150
118
BS75
750
1010×520
432-1000
568
1130×520×1260
55
150
120
BS100
1000
1010×520
440-960
520
1130×520×1260
68
150
137
BS30D
300
1010×520
435-1585
1150
1130×520×1260
53
150
150
BS50D
500
1010×520
435-1585
1150
1130×520×1260
68
150
168
BS80D
800
1010×520
490-1400
910
1130×520×1275
95
150
165
6. Service instruction
6.1-1. Lubricate each point described below every month:
6.2.Change hydraulic oil every 12 months.
Lubricating Points
(1) Fitting of cylinder……Oil
(2) Roller friction surface……Grease
(3) Link Pin ……Oil
(4) Pedal fitting point……Oil
(5) Link center pin……Oil
(6) Joint……Grease
(7) Grease nipple……Grease
(8) Hydraulic circuit
5
7. Hydraulic Circuit
6
7
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1
Table pair
1
48
Spring washer
1
2
Guide roller
4
49
Washer
1
3
Scissors
1
50
Bushing
1
4
Snap ring
6
51
Steel ball
1
5
Link pin
4
52
Steel ball holder
1
6
Safety pin
1
53
Relief spring
1
7
Hex bolt
16
54
Regulating pressure plug
1
8
Washer
18
55
O ring 1 9
Frame pair
1
56
Relief plug
1
10
Front wheel
2
57
O ring 1 11
Spring washer
19
58
Plug
1
12
Hex. nut
18
59
Rear wheel
2
13
Piston rod
1
60
Handle pin
4
14
Dust seal
1
61
Handle lock spring L
1
15
O ring 2 61A
Handle lock spring R
1
16
Back up ring
1
62
Bushing
2
17
Cylinder pair
1
63
Snap ring
4
18
Spring seat
1
64
Pedal holder
1
19
Spring 1 65
Snap ring
2
20
Seal ring
1
66
Pressure roller
1
21
Joint 1 67
Pressure roller pin
1
22
Flow control joint
1
68
Pedal Pivot Pin
1
23
O ring 1 69
Hex. bolt
2
24
Adjust casing
1
70
Elbow 2 25
Spring seat
1
71
Oil retum hose
1
26
Valve spring
1
72
Rubber bushing
1
27
Conical valve
1
73
High pressure hose
1
28
Valve seat
1
74
Seal ring
6
29
O ring 1 75
Adaptor
2
30
Steel ball φ7
1
76
Pedal Pair
1
31
Dust seal
1
77
Pedal rubber
1
32
Y ring 1 78
Hex bolt
1
33
Plunger
1
79
Lock bar
1
34
Pump spring B
1
80
Hex. bolt
1
35
Pump spring A
1
81
Cylinder pivot pin
1
36
Pump bass
1
82
Grease fitting
2
37
Net 1 83
Piston head pin
1
38
Washer
1
84
Roller chain
1
39
Back valve spring
2
85
Valve rod Ⅱ
1
40
O-ring 1 86
Nut M6
1
41
Plug 1 87
Handle pair
1
8
42
O ring 1 88
Valve rodⅠ
1
43
Steering bush
1
89
Control link
1
44
O ring 1 90
Roll pin
1
45
Discharge lever
1
91
Roll pin
1
46
Valve arm
1
92
Check ring
2
47
Socket head screw
1
A
Cylinder Assembly
13-21
B
Pump Unit Assembly
64-78
C
Pump Unit Sub Assembly
22-58
D
Handle Assembly
84-91
E
Pedal Assembly
76-77
F
Seal kit ass'y
14,15,20,23,29,31,32,40,42,44,55,57,74
9
10
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1.
Seal cover d30×D42×7
1
53.
Lever bushing
1
2.
Cylinder cover
1
54.
Washer 6
2
3.
O-ring d63×2.65
2
55.
Spring washer 6
1
4.
O-ring d30×3.55
1
56.
Hex soch screw M6×16
1
5.
Piston rod
1
57.
Put pressure assembly line
1
6.
Spacing casing
1
59.
Nut M8
17
7.
Guide ringδ1.5×15
1
60.
Washer 8
30
8.
O-ring D20×2.4
1
62.
Spring pin
1
9.
Seal ring d34×D40×4.5
1
63.
Control link
1
10.
Piston rod retainer
1
64.
Handle
1
11.
Retaining ring 18
1
65.
Spacing casing
2
12.
Piston
1
66.
Spring washer 12
2
13.
Cylinder
1
67.
Hexagon head stud M12×30
2
14.
Cylinder washer
1
68.
Split pin
1
15.
Reservior
1
69.
Pin 1 16.
O-ring d10×2.65
1
73.
Pedal bent pipe
1
17.
Filler screw
1
74.
Pedal rubber
1
18.
Washer for reservior
1
75.
Shake link
1
19.
Steel ball 5
1
76.
Spring washer 8
17
20.
Spring base
1
77.
Hex soch screw
1
21.
Regulating pressure spring
1
78.
Buffer mat
1
22.
Regulating pressure screw
1
79.
Partition set
1
23.
O-ring d7.1×1.8
1
80.
Pin axle
1
24.
End cover
1
81.
Retainer 10
2
25.
O-ring d15×2.65
2
82.
Pin axle
1
26.
Regulating speed spring
1
83.
Retainer 20
1
27.
Regulating speed slide valve
1
84.
Washer
1
28.
Regulating speed spring casing
1
85.
Pin axle
1
29.
Regulating speed valve casing
1
86.
Link 2 30.
Steel ball 7
1
87.
Hex soch screw M8×25
16
31.
O-ring d6.9×1.8
1
88.
Wheel
2
32.
Conical valve
1
89.
Wheel
2
33.
Check valve spring
1
90.
Chassis
1
34.
Check valve casing
1
91.
Pin axle
1
35.
O-ring d10×1.8
1
92.
Bolt M6×8
1
36.
Check valve screw
1
93.
Bushing
2
37.
Spring base
1
94.
Scissors lever
1
38.
Spring 1 95.
Retainer 16
9
39.
Seal cover d18×D25×4.5
1
96.
Roller for chassis
2
40.
O-ring d18×2.65
1
97.
Bushing
2
41.
Pump plunger
1
98.
Nut M10
2
11
42.
Y-ring 1 100.
Washer 10
4
43.
Pump body for plunger
1
101.
Satety rod
2
44.
O-ring d28×3.1
1
102.
Screw bolt M10×40
2
45.
Pump body
1
103.
Spring pin 8×30
2
46.
O-ring d10.6×2.65
1
104.
Roller for table
2
47.
Spring
1
105.
Table 1 48.
Reflux rod
1
106.
Pin axle
1
49.
O-ring d4×1.8
1
107.
Pin axle
2
50.
Guide casing
1
108.
Screw M6×30
1
51.
Protect casing
1
109.
Cover-type nut M6
1
52.
Lever 1
A
Pump ass’y
1～51
B
Swivel wheel ass’y
88 C Front wheel ass’y
89 D Sealkit ass’y
1,3,4,7,8,9,16,23,25,31,35,39,40,42,44,46,49
E
Handle ass’y
54,55,57,62,63,64,68,69,108,109
12
13
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1.
Seal cover d30×D42×7
1
54.
Hex soch screw M6×16
1
2.
Cylinder cover
1
55.
Put pressure assembly line
1
3.
O-ring d63×2.65
2
58.
Washer 8
2
4.
O-ring d30×3.55
1
60.
Spring pin 5×14
1
5.
Piston Rod
1
61.
Control link
1
6.
Spacing casing
1
62.
Handle
1
7.
Guidering δ1.5×15
1
63.
Spacing casing
2
8.
O-ring D20×2.4
1
64.
Spring washer 12
2
9.
Seal ring d34×D40×4.5
1
65.
Hex screw M12×30
2
10.
Retainer for piston rod
1
66.
Split pin 2×15
1
11.
Spacing retainer 18
1
67.
Pin
1
12.
Piston
1
71.
Pedal bent pipe
1
13.
Cylinder
1
72.
Hex soch screw M8×20
2
14.
Washer for cylinder
1
73.
Shake link
1
15.
Reservior
1
74.
Spring
2
16.
O-ring d10×2.65
1
75.
Retainer 10
2
17.
Filler screw
1
76.
Pin axle
2
18.
Washer for reservior
1
77.
Link 2 19.
Steel ball 5
1
78.
Wheel
2
20.
Spring base
1
79.
Nut M10
16
21.
Regulating pressure spring
1
80.
Spring washer 10
16
22.
Regulating pressure screw
1
81.
Washer 10
36
23.
O-ring d7.1×1.8
1
82.
Hex soch screw M10×25
16
24.
End cover
1
83.
Wheel
2
25.
O-ring d15×2.65
2
84.
axle 1 26.
Regulating speed spring
1
85.
Retainer 20
7
27.
Regulating slide-valve
1
86.
Chassis
1
28.
Regulating speed spring casing
1
87.
Table
1
29.
Regulating speed slide-casing
1
88.
Roller for table
2
30.
Steel ball 7
1
89.
Bushing
2
31.
O-ring d6.9×1.8
1
90.
Split pin 3.2×26
1
32.
Conical valve
1
91.
Nut M16
1
33.
Spring
1
92.
Washing
1
34.
Check valve casing
1
93.
Bushing
4
35.
O-ring d10×1.8
1
94.
Spring pin 8×30
2
36.
Check valve screw
1
95.
Screw bolt M10×40
2
37.
Seal cover d18×D25×4.5
1
96.
Safety rod
2
38.
O-ring d18×2.65
1
97.
Nut M10
2
39.
Pump plunger
1
98.
External scissors lever
1
40.
Y-ring 1 99.
Bushing
2
41.
Pump body for plunger
1
100.
Roller for chassis
2
14
42.
O-ring D28×3.1
1
101.
Internal scissors lever
1
43.
Pump body
1
102.
Pin axle for chassis
1
44.
O-ring d10.6×2.65
1
103.
Spring washer 8
1
45.
Spring
1
104.
Hex screw M8×16
1
46.
Reflux rod
1
105.
Pin axle for scissons
1
47.
O-ring d4×1.8
1
106.
Pin axle for table
1
48.
Guide casing
1
107.
Bushing
2
49.
Protect casing
1
108.
Bolt M8×12
1
50.
Lever
1
109.
Oil cup
2
51.
Lever bushing
1
110
Bolt M6×8
1
52.
Washer 6
2
111
Screw M6×30
1
53.
Spring washer 6
2
112
Cover-type nut M6
1
A
Pump ass’y
1～49
B
Swivel wheel ass’y
78 C Front wheel ass’y
83 D Sealkit ass’y
1,3,4,7,8,9,16,23,25,31,35,37,38,40,42,44,47
E
Handle ass’y
52,53,55,60,61,62,66,67,111,112
15
16
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1.
Seal cover d35×D43.5×5
1
56.
Put pressure assembly line
1
2.
Cylinder cover
1
59.
Washer 8
2
3.
O-ring d75×3.55
1
61.
Spring pin
1
4.
O-ring d35.5×3.55
1
62.
Control link
1
5.
Piston Rod
1
63.
Handle
1
6.
Spacing casing
1
64.
Spacing casing
2
7.
Guideing δ2×15
1
65.
Spring washer 12
2
8.
O-ring D20×2.4
1
66.
Hex screw M12×30
2
9.
Seal ring d39×D45×4.5
1
67.
Split pin 2×15
1
10.
Retainer for piston rod
1
68.
Pin 1 11.
Spacing retainer 18
1
72.
Pedal bent pipe
1
12.
Piston
1
73.
Hex screw M8×20
2
13.
Cylinder
1
74.
Shake link
1
14.
Washer for cylinder
1
75.
Spring
2
15.
Reservior
1
76.
Pin axle
2
16.
O-ring d10×2.65
1
77.
Retainer 10
2
17.
Filler screw
1
78.
Link 2 18.
O-ring d75×2.65
1
79.
Table
1
19.
Washer for reservior
1
80.
Retainer 20
7
20.
Steel ball 5
1
81.
Roller for table
2
21.
Spring base
1
82.
Bushing
2
22.
Regulating pressure spring
1
83.
Split pin 3.2×26
2
23.
Regulating pressure screw
1
84.
Nut M16
2
24.
O-ring d7.1×1.8
1
85.
Washing
2
25.
End cover
1
86.
Bushing
2
26.
O-ring d15×2.65
2
87.
Pin axle for scissors
2
27.
Regulating speed spring
1
88.
Spring washer 8
2
28.
Regulating slide-valve
1
89.
Hex screw M8×16
2
29.
Regulating speed spring casing
1
90.
Spring pin 8×30
2
30.
Regulating speed slide-casing
1
91.
Screw bolt M10×40
2
31.
Steel ball 7
1
92.
Washer 10
36
32.
O-ring d6.9×1.8
1
93.
Safety rod
2
33.
Conical valve
1
94.
Spring washer 10
16
34.
Spring
1
95.
Nut M10
2
35.
Check valve casing
1
96.
External scissors lever
1
36.
O-ring d10×1.8
1
97.
Bushing
2
37.
Check valve screw
1
98.
Roller for chassis
2
38.
Seal cover d18×D25×4.5
1
99.
Bushing
2
39.
O-ring d18×2.65
1
100.
Pin axle for chassis
1
40.
Pump plunger
1
101.
Pin axle for table
1
41.
Y-ring d10×D18×6
1
102.
Bushing
2
17
42.
Pump body for plunger
1
103.
Oil cup
1
43.
O-ring D28×3.1
1
104.
Bolt M8×12
1
44.
Pump body
1
105.
Internal scissors lever
1
45.
O-ring d10.6×2.65
1
106.
Chassis
1
46.
Spring
1
107.
axle 1 47.
Reflux rod
1
108.
Hex soch screw M10×25
16
48.
O-ring d4×1.8
1
109.
Nut M10
16
49.
Guide casing
1
110.
Wheel
2
50.
Protect casing
1
111.
Wheel
2
51.
Lever 1 112
Rod 1 52.
Lever bushing
1
113
Rod 1 53.
Washer 6
2
114
Bolt M6×8
1
54.
Spring washer 6
2
115
Screw M6×30
1
55.
Hex soch screw M6×16
1
116
Cover-type nut M6
1
A Pump ass’y
1～50,112,113
B
Swivel wheel ass’y
111 C Front wheel ass’y
110 D Sealkit ass’y
1,3,4,7,8,9,16,18,24,26,32,36,39,41,43,45,48
E
Handle ass’y
53,54,56,61,62,63,67,68,115,116
18
19
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1.
Seal cover d35×D43.5×5
1
56.
Put pressure assembly line
1
2.
Cylinder cover
1
59.
Washer 8
2
3.
O-ring d75×3.55
1
61.
Spring pin
1
4.
O-ring d35.5×3.55
1
62.
Control link
1
5.
Piston Rod
1
63.
Handle
1
6.
Spacing casing
1
64.
Spacing casing
2
7.
Guideing δ2×15
1
65.
Spring washer 12
2
8.
O-ring D20×2.4
1
66.
Hex screw M12×30
2
9.
Seal ring d39×D45×4.5
1
67.
Split pin 2×15
1
10.
Retainer for piston rod
1
68.
Pin
1
11.
Spacing retainer 18
1
72.
Pedal bent pipe
1
12.
Piston
1
73.
Hex screw M8×20
2
13.
Cylinder
1
74.
Shake link
1
14.
Washer for cylinder
1
75.
Spring
2
15.
Reservior
1
76.
Pin axle
2
16.
O-ring d10×2.65
1
77.
Retainer 10
2
17.
Filler screw
1
78.
Link 2 18.
O-ring d75×2.65
1
79.
Table
1
19.
Washer for reservior
1
80.
Retainer 20
7
20.
Steel ball 5
1
81.
Roller for table
2
21.
Spring base
1
82.
Bushing
2
22.
Regulating pressure spring
1
83.
Split pin 3.2×26
2
23.
Regulating pressure screw
1
84.
Nut M16
2
24.
O-ring d7.1×1.8
1
85.
Washing
2
25.
End cover
1
86.
Bushing
2
26.
O-ring d15×2.65
2
87.
Pin axle for scissors
2
27.
Regulating speed spring
1
88.
Spring washer 8
2
28.
Regulating slide-valve
1
89.
Hex screw M8×16
2
29.
Regulating speed spring casing
1
90.
Spring pin 8×30
2
30.
Regulating speed slide-casing
1
91.
Screw bolt M10×40
2
31.
Steel ball 7
1
92.
Washer 10
36
32.
O-ring d6.9×1.8
1
93.
Safety rod
2
33.
Conical valve
1
94.
Spring washer 10
16
34.
Spring
1
95.
Nut M10
2
35.
Check valve casing
1
96.
External scissors lever
1
36.
O-ring d10×1.8
1
97.
Bushing
2
37.
Check valve screw
1
98.
Roller for chassis
2
38.
Seal cover d18×D25×4.5
1
99.
Bushing
2
39.
O-ring d18×2.65
1
100.
Pin axle for chassis
1
40.
Pump plunger
1
101.
Pin axle for table
1
20
41.
Y-ring d10×D18×6
1
102.
Bushing
2
42.
Pump body for plunger
1
103.
Oil cup
1
43.
O-ring D28×3.1
1
104.
Bolt M8×12
1
44.
Pump body
1
105.
Internal scissors lever
1
45.
O-ring d10.6×2.65
1
106.
Chassis
1
46.
Spring
1
107.
axle 1 47.
Reflux rod
1
108.
Hex soch screw M10×25
16
48.
O-ring d4×1.8
1
109.
Nut M10
16
49.
Guide casing
1
110.
Wheel
2
50.
Protect casing
1
111.
Wheel
2
51.
Lever 1 112
Rod 1 52.
Lever bushing
1
113
Rod
1
53.
Washer 6
2
114
Bolt M6×8
1
54.
Spring washer 6
2
115
Screw M6×30
1
55.
Hex soch screw M6×16
1
116
Cover-type nut M6
1
A Pump ass’y
1～50,112,113
B
Swivel wheel ass’y
111 C Front wheel ass’y
110 D Sealkit ass’y
1,3,4,7,8,9,16,18,24,26,32,36,39,41,43,45,48
E
Handle ass’y
53,54,56,61,62,63,67,68,115,116
21
22
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1.
Seal cover d30×D42×7
1
55.
Put pressure assembly line
1
2.
Cylinder cover
1
58.
Washer 8
2
3.
O-ring d63×2.65
2
60.
Spring pin
1
4.
O-ring d30×3.55
1
61.
Control link
1
5.
Piston Rod
1
62.
Handle
1
6.
Spacing casing
1
63.
Spacing casing
2
7.
Guideing δ1.5×15
1
64.
Spring washer 12
2
8.
O-ring D20×2.4
1
65.
Hex screw M12×30
2
9.
Seal ring d34×D40×4.5
1
66.
Split pin 2×15
1
10.
Retainer for piston rod
1
67.
Pin 1 11.
Spacing retainer 18
1
71.
Pedal bent pipe
1
12.
Piston
1
72.
Hex soch screw M8×20
2
13.
Cylinder
1
73.
Shake link
1
14.
Washer for cylinder
1
74.
Spring
2
15.
Reservior
1
75.
Retainer 10
2
16.
O-ring d10×2.65
1
76.
Pin axle
2
17.
Filler screw
1
77.
Link 2 18.
Washer for reservior
1
78.
Wheel
2
19.
Steel ball 5
1
79.
Nut M10
16
20.
Spring base
1
80.
Spring washer 10
16
21.
Regulating pressure spring
1
81.
Washer 10
36
22.
Regulating pressure screw
1
82.
Hex soch screw M10×25
16
23.
O-ring d7.1×1.8
1
83.
Wheel
2
24.
End cover
1
84.
axle 1 25.
O-ring d15×2.65
2
85.
Retainer 20
7
26.
Regulating speed spring
1
86.
Chassis
1
27.
Regulating slide-valve
1
87.
Hex screw M8×16
5
28.
Regulating speed spring casing
1
88.
Pin axle for chassis
1
29.
Regulating speed slide-casing
1
89.
Bushing
10
30.
Steel ball 7
1
90.
Washing
5
31.
O-ring d6.9×1.8
1
91.
Slotting nut M16×1.5
5
32.
Conical valve
1
92.
Split pin 3.2×26
5
33.
Spring
1
93.
Pin axle
3
34.
Check valve casing
1
94.
Pin axle for table
1
35.
O-ring d10×1.8
1
95.
Hex socket set screw M8×12
1
36.
Check valve screw
1
96.
Bushing
2
37.
Seal cover d18×D25×4.5
1
97.
Oil cup
4
38.
O-ring d18×2.65
1
98.
External scissors lever for table
1
39.
Pump plunger
1
99.
Internal scissors lever for table
1
40.
Y-ring
1
100.
Bushing
2
41.
Pump body for plunger
1
101.
Roller for table
2
23
42.
O-ring D28×3.1
1
102.
Table
1
43.
Pump body
1
103.
Spring pin 8×30
2
44.
O-ring d10.6×2.65
1
104.
Screw bolt M10×40
2
45.
Spring
1
105.
Safety rod
2
46.
Reflux rod
1
106.
Nut M10
2
47.
O-ring d4×1.8
1
107.
External scissors lever for
chassis
1
48.
Guide casing
1
108.
Internal scissors lever for
chassis
1
49.
Protect casing
1
109.
Bushing
2
50.
Lever
1
110.
Roller for chassis
2
51.
Lever bushing
1
111.
Pin axle
2
52.
Washer 6
2
112
Bolt M6×8
1
53.
Spring washer 6
2
113
Screw M6×30
1
54.
Hex soch screw M6×16
1
114
Cover-type nut M6
1
A Pump ass’y
1～49,113,114
B
Swivel wheel ass’y
78 C Front wheel ass’y
83 D Sealkit ass’y
1,3,3A,4,7,8,9,16,23,25,31,35,37,38,40,42,44,47
E
Handle ass’y
52,53,55,60,61,62,66,67,115,116
24
25
NO.
DESCRIPTION
Qty
NO.
DESCRIPTION
Qty
1.
Seal cover d35×D43.5×5
1
60.
Spring pin
1
2.
Cylinder cover
1
61.
Control link
1
3.
O-ring d75×3.55
1
62.
Handle
1
3A
O-ring d75×2.65
1
63.
Spacing casing
2
4.
O-ring d35.5×3.55
1
64.
Spring washer 12
2
5.
Piston Rod
1
65.
Hex screw M12×30
2
6.
Spacing casing
1
66.
Split pin 2×15
1
7.
Guideing δ2×15
1
67.
Pin 1 8.
O-ring D20×2.4
1
71.
Pedal bent pipe
1
9.
Seal ring d39×D45×4.5
1
72.
Hex soch screw M8×20
2
10.
Retainer for piston rod
1
73.
Shake link
1
11.
Spacing retainer 18
1
74.
Spring
2
12.
Piston
1
75.
Retainer 10
2
13.
Cylinder
1
76.
Pin axle
2
14.
Washer for cylinder
1
77.
Link 2 15.
Reservior
1
78.
Wheel
2
16.
O-ring d10×2.65
1
79.
Nut M10
16
17.
Filler screw
1
80.
Spring washer 10
16
18.
Washer for reservior
1
81.
Washer 10
36
19.
Steel ball 5
1
82.
Hex soch screw M10×25
16
20.
Spring base
1
83.
Wheel
2
21.
Regulating pressure spring
1
84.
axle 1 22.
Regulating pressure screw
1
85.
Retainer 20
7
23.
O-ring d7.1×1.8
1
86.
Chassis
1
24.
End cover
1
87.
Hex screw M8×16
5
25.
O-ring d15×2.65
2
88.
Pin axle for chassis
1
26.
Regulating speed spring
1
89.
Bushing
8
27.
Regulating slide-valve
1
89A
Bushing
2
28.
Regulating speed spring casing
1
90.
Washing
3
29.
Regulating speed slide casing
1
90A.
Washing
2
30.
Steel ball 7
1
91.
Slotting nut M16×1.5
5
31.
O-ring d6.9×1.8
1
92.
Split pin 3.2×26
5
32.
Conical valve
1
93.
Pin axle
3
33.
Spring
1
94.
Pin axle for table
1
34.
Check valve casing
1
95.
Hex socket set screw M8×12
1
35.
O-ring d10×1.8
1
96.
Bushing
2
36.
Check valve screw
1
97.
Oil cup
4
37.
Seal cover d18×D25×4.5
1
98.
External scissors lever for table
1
38.
O-ring d18×2.65
1
99.
Internal scissors lever for table
1
39.
Pump plunger
1
100.
Bushing
2
40.
Y-ring d10×D18×6
1
101.
Roller for table
2
26
41.
Pump body for plunger
1
102.
Table
1
42.
O-ring D28×3.1
1
103.
Spring pin 8×30
2
43.
Pump body
1
104.
Screw bolt M10×40
2
44.
O-ring d10.6×2.65
1
105.
Safety rod
2
45.
Spring
1
106.
Nut M10
2
46.
Reflux rod
1
107.
External scissors lever for chassis
1
47.
O-ring d4×1.8
1
108.
Internal scissors lever for chassis
1
48.
Guide casing
1
109.
Bushing
2
49.
Protect casing
1
110.
Roller for chassis
2
50.
Lever
1
111.
Pin axle
2
51.
Lever bushing
1
112.
Bolt M6×8
1
52.
Washer 6
2
113.
Rod
1
53.
Spring washer 6
2
114.
Rod
1
55.
Put pressure assembly line
1
115.
Screw M6×30
1
58.
Washer 8
2
116.
Cover-type nut M6
1
A Pump ass’y 1～49,113,114
1～49,113,114
B
Swivel wheel ass’y
78 C Front wheel ass’y
83 D Sealkit ass’y
1,3,3A,4,7,8,9,16,23,25,31,35,37,38,40,42,44,47
E
Handle ass’y
52,53,55,60,61,62,66,67,115,116
Loading...