Silver Spring SC500-AF Instructions Manual
Deluxe Aluminum Folding Scooter & Wheelchair Carrier
Instructions for Part # SC500-AF
General Guidelines
• It is the user’s responsibility to read and follow all instructions.
• Keep these instructions with the product at all times and review before each use.
• It is the responsibility of this product’s owner to furnish the instructions to any person that borrows
or purchases the product.
• Inspect the product before use to ensure it is assembled properly and all parts are in safe working
order and free of defects.
• Never modify this product in any way.
• All circumstances cannot be addressed in these instructions. Please use common sense and
practice general safety measures when using this product.
• Parts and/or instructions are subject to change without notice.
Safety
• Follow all warnings and instructions marked on the product.
• Do not occupy the mobility aid while loading the carrier.
• Do not stand on the carrier.
• Never exceed vehicle tongue weight rating.
• The carrying capacity is 500 lbs.
• Hitch adapters may aect the weight capacity of the carrier. If using a hitch adapter, always check
its limitations before use.
• Always store the carrier in a safe place.
• Improper use, storage, or installation of the carrier could result in death or serious injury.
• Do not put the product on any kind of trailer.
• NOT recommended for tow-behind trailers including 5th wheel trailers and camping trailers.
• Periodically check nuts and bolts for tightness.
Tools Required
• 13mm or 1/2" wrench
• 14mm or 9/16" wrench
• 17mm wrench
DiscountRamps.com • 1-888-651-3431
• 19mm or 3/4" wrench
• 22mm or 7/8" wrench
• 10mm Allen wrench
Page 1Rev. 091218
Parts
1
8 9
10 11 12
13 14 15
2
3
4 5
6 7
16 17
19
20 21
22
24
18
23
25
Part Description Quantity
1 Carrier 1
2 Folding Hitch Tube 1
3 Carrier Support Tube 1
4 Support Bracket 2
5 Reector 2
6 Ramp Lock Plate 1
7 Spring Pull Pin 3
8 M8x20 Support Bracket Bolt 8
9 M8 Support Bracket Nut 8
10 M8x40 Carrier Support Bolt 4
11 Washer 4
12 M8 Carrier Support Nut 4
13 M8x40 Ramp Lock Carriage Bolt 2
DiscountRamps.com • 1-888-651-3431
Part Description Quantity
14 M8 Ramp Lock Nut 2
15 Ramp Lock Bracket 2
16 M8x70 Eye Bolt 4
17 M8 Eye Bolt Nut 4
18 Eye Bolt Bracket 8
19 M14x30 Bolt with Jam Nut 2
20 Ramp Handle 1
21 Ramp Handle Nut 2
22 3/8" Pinch Bolt with 5/8" Sleeve 1
23 Hitch Pin with Clip 1
24 Pull Pin with Clip 2
25 Anti-Tilt Bracket 1
Page 2Rev. 091218
Assembly
Step 1. Assemble the support
tube.
Bolt the support brackets (4) to
the carrier tube (3) using the
support bracket bolts (8) and
nuts (9) using 13mm and 14mm
wrenches.
*Note: Do not tighten bolts until
the next step.
Insert the folding hitch tube (2) into the carrier support tube (3), then lock into place with two pull pins
(24). Secure the hitch tube to the carrier tube with two bolts with jam nuts (19) using a 22mm wrench.
8
4
9
3
9
8
3
4
4
*Note: To properly tighten the bolts with jam nuts, rst thread the jam nut counterclockwise up to the
head of the bolt. Fully tighten the bolt into the carrier tube. Then tighten the jam nut clockwise against
the carrier tube to secure the bolt.
4
19
3
24
19
4
24
DiscountRamps.com • 1-888-651-3431
2
Page 3Rev. 091218
Loading...