T echnicalManual
and
ReplacementPartsList
RefrigeratedShakeStation
1600 Xenium Lane North, Minneapolis, MN 55441-3787
Phone (763) 923-2441
FORM NO. 38447 REV K 09/2018
MODEL SKFSM
Specifications Subject to Change Without Notice.
1
TECHNICAL MANUAL
SILVER KING MODEL SKFSM REFRIGERATOR
Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most reliable
equipment in the industry today. Please read this manual and the accompanying warranty information before operating your new
Silver King unit.
INSPECT FOR DAMAGE AND UNCRATE
Upon delivery of your new Silver King unit, uncrate at once to inspect for possibl e freight damage following the instr uctions printed
on the exterior of the container. Report any damages to the carrier responsible for trans portation and promptly present a claim for
any evidence of mishandling. Save all packaging materials if a claim is filed.
PRECAUTIONS BEFORE USING THIS PRODUCT
This appliance is not intended for use by persons (inclu ding childr en) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Use caution when cleaning the condenser, the fins are very sharp.
For units with a dual hertz rating, no adjustments are required for normal operation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarl y qualified persons in
order to avoid a hazard.
This refrigeration unit is not intended to be used at altitudes higher than 2000 meters.
Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
Do not exceed the maximum load capacity of 50 pounds per shelf.
Use caution when moving, installing, maintaining and using this refrigerati on device to avoid either damaging the
refrigerant tubing or increasing the risk of a leak.
All component parts must be replaced with like components and all servicing must be done by factory authorized service
personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper service.
WARNING: This product can expose you to chemicals including lead, which are known to the State of
California to cause cancer, birth defects, or other reproductive harm.
1
INSTALLATION
The stainless steel exterior of the cabinet has been protected by a plastic covering during manufacturing and shipp ing. This covering
can be readily stripped before installation. After removing this coverin g, wash the interior and exterior surfaces using a warm, mild
soapy water solution and a sponge or cloth, rinse with clean water and dry.
Shelves
Inside the unit you will find A Shelf and a plastic bag containing Shelf Supports. This shelf system allo ws for easy adjustment to suit
your needs.
Door Adjustment and Swing
Should the Door ever require straightening, loosen the Screws on the Hinges, square the Door with the cabinet and retighten the
Screws.
The mounting of the Door is easily reversible on single do or units should space or convenience r equire that you do s o. Simply remove
the Screws holding the Hinges, rotate the Door 180 degrees and relocate the Hinges on the side opposite their original location.
Location
When locating your new refrigerator, convenience and accessibility are important considerations, but the following installation
guidelines must be followed;
Always avoid placing the refrigerator adjacent to a n oven, heating element or hot air source that would affect the operation of the
unit.
For proper ventilation the unit requires the following minimum clearances:
-4 inches in back
-2 inches on the sides and 2 inches above the cabinet
The unit must be level or tilted backwards slightly.
Energy Rating
Your Silver King refrigerator has a class 5 energy rating. The refrigerator was tested at an ambient temperature of 40°C at 40% relative
humidity.
2
Electrical Connections
Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to power. The
specifications on the data plate supersede any future discussion.
The standard refrigerator is equipped with an eight (8) foot power cord that requires a properly grounded electrical receptacle.
The power cord comes with a 3 prong plug for groundin g purposes. Any attempt to cut off the grounding sp ike or to connect to an
ungrounded adapter plug will void the warranty, terminate the manufacturers responsib ility and could result in serious injury.
The circuit must be protected with a 15 or 20 ampere fuse or breaker. The unit must be isolated on a circuit and not pl ugged into an
extension cord.
OPERATION
Initial start up
After satisfying the installation requirements, the refrigerator is rea dy to start. The Compressor will start when the power cord is
connected to the required power source. If the Compress or does not start when the u nit is initially plugge d in, check to make sure
that the Temperature Control is not in the “off” position. Allow the unit to run for two hours before lo ading it with product. When
loading the unit with product, take care not to block the air flow in the cabinet as this would affect the units performance.
Temperature Control
The Temperature Control is located on the back of the cabinet and is factory set to maintain an average cabinet temperature of
approximately 38 Deg F. To adjust the set point, pus h a nd hol d the ‘set’ b utton for t wo seconds then p ush the up or d o wn arrows to
adjust the set point. Either press the ‘set’ button again or wait 10 seconds and the control will store the new set point. Allow the unit
a minimum of one hour to respond to a control setting adjustment.
Defrost
Your Silver King refrigerator will defrost naturally and no additional plu mbing is required. Evaporator defrosting is accomplished
when frost buildup on the Evaporator Coil is cleared during Compressor “off” c ycles. Defrost water is collected in a pan located in
the compressor compartment where it is evaporated into the room air. It is important that the unit be installed level to allow prop er
drainage of the defrost water.
MAINTENANCE
Preventative maintenance is minimal although these few steps are very important to continued operati on and maximizing the life of
the appliance.
Cabinet Surfaces
The cabinet interior is aluminum and stainless steel and the exterior is stainless steel. These surfaces should be cleaned
periodically with a solution of warm water an d mild soap, rinsed and wiped dr y with a soft cloth. A go od stainless steel cl eaner can
also be used. Should a surface become stained, do not attempt to clean with an abrasive cleans er or scouring pad. Use a soft
cleanser and rub with the grain of the metal to avoid scratch ing the surface. Do not use chlorinated cleaners. Always rinse well and
dry after cleaning.
Condenser
Periodically, accumulated dust must be removed from the condenser. First, disconnect the unit from the po wer supply. To clear the
dust, vacuum or brush the condenser at the bottom rear of the cabinet. This will need to be done regularly to maintain the
compressor warranty!
WARNING: The condenser fins are very sharp, use caution when cleaning the condenser.
Door Gasket
The Door Gasket will collect dirt and should be wiped clean with a warm, mild soapy water solution to extend its life and assure
maximum cabinet performance and life.
MODEL SERIAL NO. DATE INSTALLED
3
4
WHEN ORDERING REPLACEMENT PARTS, PLEASE PROVIDE MODEL AND SERIAL NUMBERS.
5
6
SILVER KING LIMITED WARRANTY
Silver King Refrigeration warrants to the original purchaser of Silver King refrigerated equipment that the equipment shall be free from
defects in material and workmanship under normal use and service as outlined in the Technical Man ual. This limited warranty shall
apply for a period of one (1) year from the date of original purchase. The Compressor will carry an additional four (4) year warranty.
All warranties are subject to specific limitations outlined below.
This limited warranty does not apply to repair or replacement required as a result of carelessness, neglect and/or abuse, including
improper installation, incorrect voltage supply, tampering with or altering components and/or equipment or failure to perform proper
maintenance. Equipment damaged in transit, by fire, flood or an act of God is not covered. This limited warranty does not include
freight, handling, installation, labor (following the one (1) year labor warranty period) or other incidental or consequential costs including
product and/or economic loss. This limited warranty is in lieu of all other warranties, express or implied, includi ng those of
merchantability, and is non-transferable.
Specific provisions of this limited warranty are as follows:
One (1) Year Parts Warranty
Silver King warrants to the original purchaser of new Silver King equipment that such equipment an d all parts thereof will be free of
defects in material and workmanship, under normal use and service, for a period of one (1) year from the date of original purchase or
18 months from the date of shipment from the factory, whichever comes first, subject to all terms and conditions herein.
This warranty is limited to repairing or replacing any parts that, at Silver King’s discretion, are deemed to be defective within the time
period covered by this warranty. The one year parts warranty covers reasonable freight and handling charges. It does not cover
special handling charges or expedited means for transport. Use of non-OEM parts may, at Silver King’s discretion, void this warranty.
If approved, warranty credit for non-OEM parts will be issued at the OEM cost.
Replacement parts sold separately are warranted for 90-days from date of purchase.
Five (5) Year Compressor Warranty
Silver King warrants to the original purchaser for a period of five (5) years from the date of original purchase or five (5) years and si x (6)
months from the date of shipment from the factory, whichever comes first, that it will replace the compressor with one of similar design
and capacity, exclusive of delivery and installation charges, if it is found to Silver King’s satisfaction to be inefficient or inoperative due
to defects in material or factory workmanship. It is the owner’s responsibility to return the serial plate of the defective compressor, or at
Silver King’s option the complete compressor, to the factory. Failure to do so will void the warranty.
Three (3) Year Heavy Duty Drawer Slide Warranty
Silver King warrants to the original purchaser for a period of three (3) years from the date of original purchase or thre e (3) years and six
(6) months from the date of shipment from the factory, whichever comes first, that it will replace the heavy duty drawer slides wit h on e
of similar design and capacity, exclusive of delivery and installation charges, if it is found to Silver King’s satisfaction to be inefficient or
inoperative due to defects in material or factory workmanship.
One (1) Year Labor Warranty
Silver King warrants to the original purchaser for a period of one (1) year from the date of purchase or 18 months from the date of
shipment from the factory, whichever comes first, a limited service labor warranty on Silver King refrigerated equipment subject to the
following terms;
A factory issued Service Authorization Number must be obtained prior to work being performed under the labor warranty. Call your
supplier or Silver King. Claims submitted without a Service Authorization Number will be paid at Silver King’s discretion.
The labor warranty includes standard straight time labor charges in accordance with Silver King’s Labor Warranty Guidelines and
reasonable travel time, as determined by Silver King.
The warranty does not cover original installation, startup, normal adjustments or maintenance. Normal adjustments and maintenance
include, but are not limited to; temperature control adjustments, temperature indicator calibrations, coil and filter cleaning, condensate
drain cleaning.
A second service call for a related failure is not covered.
Use of refrigerants other than specified on the equipment serial plate voids the warranty.
All claims must include; model and serial number of equipment, date of purchase, date of failure, and a copy of the service invoice
detailing the defect and service performed. No claim will be processed without this information. All claims must be filed within 60 days
from date of service.
P/N 26355 Revision C
7
Loading...