Silicon Laboratories UNI-C8051F020 User Manual

UNI-C8051F020
SILICON LABS
UNI PROTO BD
C8051
F020
U1
DEBUG
J1
J6
DGND VDD
Silicon Laboratories
USB DEBUG ADAPTER
Run
Stop Power
USB Debug
Adapter
PC
Variable Power Supply (1 Amp Max)
3.3V
C8051F020 UNI PROTOTYPE BOARD USERS GUIDE

1. Summary

The UNI Prototype Board provides easy development and debugging of applications on the C8051F020 microcontroller through use of a JTAG debug header and direct through-hole access to each pin.

2. Features

C8051F020 MCUJTAG debug header0.1-inch center through-hole access to each pinAccess to V

3. Hardware Setup

A USB Debug Adapter or EC2 Serial Adapter may be used to connect through the JTAG interface as shown in Figure 1. Power to the device must be supplied externally through pin V
1. Connect the 10-pin ribbon cable from the debug adapter to the JTAG interface.
2. Connect the other end of the debug adapter to the appropriate port on the PC.
3. Connect an external power supply to the device by connecting the grounding cable to pin DGND on J6 and the power cable to pin V
4. Set the power supply voltage to +3.3 V.
Note: Ensure the power supply is off when connecting or disconnecting cables to the device in order to prevent accidental
damage to device and/or debug adapter.
and DGND for an external voltage supplier
DD
.
DD
DD
on J6.

Figure 1. UNI Prototype Board Hardware Setup

Rev. 0.1 11/08 Copyright © 2008 by Silicon Laboratories UNI-C8051020
UNI-C8051F020
USB Debug Adapter EC2 Serial Adapter
Pin # Description Pin # Description
1,8 Not Connected 1 3.0 to 3.6 VDC Input
2,3,9 GND (Ground) 2,3,9 GND (Ground)
4 TCK (C2D) 4 TCK (C2D)
5TMS 5TMS
6TDO 6TDO
7TDI (C2CK) 7TDI (C2CK)
10 USB Power 8,10 Not Connected

Table 1. Adapters

2 Rev. 0.1
NOTES:
UNI-C8051F020
Rev. 0.1 3
UNI-C8051F020
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, rep­resentation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation conse­quential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where per­sonal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap­plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.

CONTACT INFORMATION

Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032
Email: MCUinfo@silabs.com Internet:
www.silabs.com
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
4 Rev. 0.1
Loading...