Silex technology C-6700WG User Manual

Step 1 : Congure the Network

Setup Guide

W A 0 3 7 9 0 X X

Contents

C-6700WG

CX User Software

When the product is placed in the horizontal (side) position, please use the rubber feet provided to prevent the unit from sliding. Place one on each corner.

For User Registration

Power Supply

Rubber Feet

Stand

Setup Guide

Warranty Booklet

This Setup Guide explains how to congure C-6700WG (this product) to be used in a wireless LAN environment.

Important:

The print server only needs to be configured on one computer.

After setup is complete, go to: ‘Step 2: Install the Applications’ for each computer that will use the printer.

Congure Through a Wireless LAN

The following item is required:

-USB cable

Use to connect this product and a printer. There is no need to purchase a new USB cable when a cable was bundled with the printer to be connected to this product.

This product has 3 methods of initial conguration as listed below :

- Conguration through a wireless LAN

- Conguration through a wired LAN

- Conguration using a USB memory

This Setup Guide describes how to congure this product through a wireless LAN or wired LAN.

For other conguration methods, please refer to the users manual.

Install the printer driver on your PC. For details, refer to the manual that came with your printer.

(Install the printer driver on your PC and make sure you can print with a directly attached USB connection from your computer before using this product.)

Connect the AC adapter to this product and the power plug to the outlet.

(Do not connect the printer to this product yet. Printer will be connected in ‘18’)

Perform the factor y default conguration according to the connection between this product and the PC.

- To perform the factory default conguration with a wireless LAN connection, refer to

Congure Through a Wireless LAN

- To perform the factory default conguration with a wired LAN connection, refer to

Congure Through a Wired LAN.

If this product has been used in another network, reset it to the factor y default settings.

For details on the factory default conguration, refer to To reset to the factory default settings.

Verify the Wireless LED(Green) blinks.

Insert the CD-ROM (

To reset to the factory default settings

1. Remove the AC plug from the electric outlet.

2. Push and hold the button on the print server while re-inserting the AC plug

into the electric outlet. Continue holding.

3. The Stat us LED(O range) will light when the f actor y default conguration settings have been restored. Release the push switch.

CX User Software

) into your Windows PC.

Check the message and click

http://www.silexamerica.com/register/

Customer Support

USA : silex technology america, Inc.

E-mail : support@silexamerica.com URL : http://www.silexamerica.com/ Phone: 801-748-1199 US Toll Free Phone: 866-765-8761

Note: A more detailed manual including troubleshooting tips can be found on the CD (Insert the CD, and click on Manual when the Autorun menu appears) of this product.

Safety instructions are noted in the Readme le on the CX User Software . Be sure to read them before using this product.

- Safety instructions regarding the radio waves

Please note the following instructions:

- Do not use this product near medical devices such as a heart pacemaker. The radio wave generated by this product may interfere with the operation of these devices and may threaten one's life.

- Do not use this product near microwave ovens. The radio wave used by microwave ovens may cause interference to this product.

Startup menu is displayed. Click

Print Server Setup

11.

Click Wireless.

* In a Windows XP (SP2 or higher) or Vista environment, the above message

will be displayed. Select Yes.

* The User Account Control screen is displayed when conguration is performed

on Windows Vista. Select

Continue.

12.

CX Wireless Setup screen is displayed.

Check the notes on the screen and select

Congure print server wirelessly from your computer and click

Next.

13.

Read the SOFTWARE LICENSE AGREEMENT Yes.

14.

and click

10.

If the screen above is displayed, select the wireless network card to be used and click

This screen is displayed only when two or more network cards are installed on your PC. Select this product and click Next.

Introduction

Collect wireless LAN setting information

To use this product over the wireless LAN network, you need to congure wireless LAN settings as appropriate for your network. This information needs to be identical to the communication devices such as an access point. Please collect the following information before the setup.

Write down your network conguration

Wireless mode

SSID

Encryption method

Ad hoc (ch. ) / Infrastructure

Encryption method

WEP KEY or Pre-Shared Key

WEP

(Open / Shared)

/ WPA / WPA2

If the screen above is displayed, you need to change the wireless settings on the PC manually. Read the message and click

* If you use Windows XP or Vista and the setup utility automatically

changed the wireless settings on the PC, this screen is not displayed.

OK.

15.

Conrm the conguration parameters and click

Execute

If the wireless settings on the PC dier from the conguration information on the screen above, change the PC wireless settings to match those displayed on the screen. Verify the wireless settings on the PC and click Next

Please refer to your wireless network adapter documentation for

instructions on how to temporarily change your computer’s wireless settings to match those of the print server.

Important: When you make this temporary change, your computer will no longer be connected to the wireless network or Internet. After you have completed the setup for the print server, you will need to change your computer’s wireless settings back to their current settings. Please make sure you write down the settings for your wireless network before you make these changes for the print server configuration.

16.

<< If you did not need to change the wireless settings on the PC manually in ‘11’, this screen will appear >>

Select Yes

* Application install screen will be displayed as

shown in Step 2 - 3.

and click

Finish

Select a product to be congured and click

* If your product is not displayed on the list, click

* If multipl e products are displ ayed in the list, che ck the

Ethernet Address

on the label of this product.

<< If you changed the wireless settings on the PC manually in ‘11’, this screen will appear >>

Refresh

Select Get IP Address Automatically

and click

Select the SSID for your home or oce wireless network. If your network is security enabled, enter the network key or password and conrm it.

Click

Next.

* If the wireless network that you wish to use is not shown in

the list, click

Detailed Cong and congure each setting.

The initial conguration of this product is complete and you do not need to congure the print server any more.

After setup is complete on one computer, each user that wants to use the Canon printer:

Click

Finish.

Change the wireless settings on the PC (that you have manually changed) back to the previous settings written down in ‘11’.

To ensure these settings take eect, unplug the AC adapter from the electrical outlet and then plug it back in.

Connect the printer to be shared over the network along with this product via a USB cable and insert the power plug of this product into the outlet.

Step 2: Install the Applications

Note: If you manually changed the wireless settings at ‘11’ on your PC, go straight to ‘3’ in Step 2.

Go to

on the next page

Congure Through a Wired LAN

The following items are required:

-Ethernet Hub

Use to connect this product and a printer. There is no need to purchase a new USB cable if a cable was bundled with the printer to be connected to this product.

-network cable

Click

Wired

-USB cable

* In a Windows XP (SP2 or higher) or Vista environment, the above message

will be displayed. Select

* The User Account Control screen is displayed when conguration is performed

on Windows Vista. Select Continue.

Install the printer driver on your PC. For details, refer to the manual that came with your printer.

(Install the printer driver on your PC and make sure you can print with a directly attached USB connection from your computer before using this product.)

Yes

Connect a network cable to this product. Connect the other end of the network cable to a network hub, switch, or router.

* Use a crossover cable when connecting this product directly to the PC.

Quick Setup screen is displayed.

Read the notes on the screen and click

Next.

Connect the AC adapter to this product and the power plug to the outlet.

(Do not connect the printer to this product yet. Printer will need to be connected at

Read the click Yes

SOFTWARE LICENSE AGREEMENT

‘17’.)

and

Verify the Link LED (Green) turns on and the Wireless LED (Green) turns o.

Select a product to be congured and click Next

* If your product is not displayed in the list, click

* If multipl e products are displayed in the l ist, check the

Ethernet Address on the label of this product.

Insert the CD-ROM ( PC.

CX User Software

12.

Get IP Address Automatically

Select

and click

) into your Windows

Read the message on the screen and click

13.

When you will use this product in the wireless network, select the wireless network that you wish to use from the list, enter the wireless network key and click

Startup menu is displayed.

Print Server Setup.

Click

* If the wireless network that you wish to use is not

shown in the list, click each setting.

Detailed Cong and congure

14.

Conrm the conguration parameters and click

Execute.

Step2 : Install the Application

Important: It is necessary to install the applications on each computer that will use the Canon multifunction printer.

15.

Select

Yes

and click Finish.

16.

To reect the wireless conguration, disconnect the power plug from the outlet and unplug the network cable.

* If you are to use this product in a wired LAN environment after you nish the setup, you do not have to unplug the network cable.

17.

Connect the printer to be shared over the network along with this product via a USB cable and insert the power plug of this product into the outlet.

Insert the CD-ROM ( Windows PC.

Select Yes

CX User Software) into your

and click

Finish

Check the message and click OK.

Add CX Print Wizard screen is displayed. Click

Application Installation

Click

* The User Account Control screen is displayed when conguration is

performed on Windows Vista. Select Continue.

10.

Select the destination print server and Click

Check the notes on the screen and click Next.

11.

Click

Read the SOFTWARE LICENSE AGREEMENT and click

Yes.

12.

Conrm the conguration parameters and click Finish.

* If the IP address of this product is changed after the port is created,

printing from the port will be unavailable.

Select the applications you want to install and click

CX Print

SX Virtual Link

is for printing from yo ur computer.

is for scanning and oth er functions.

13.

Select the printer you want to use with this product and click

Click Start

14.

Follow the instructions in the message on the screen and click

Finish.

* When in a Windows XP (SP2 or higher) or Vista environment, the above message will be

displayed. Select

* The message below is displayed when installing the application on Windows Vista.

(1) Windows Security screen is displayed. Choose Install. (2) The screen to conrm the user adding the application to the Windows rewall exemptions list

is displayed. Select

Yes.

Yes

15.

Click Finish. Now, the printer can be used in a network environment.

Step3 :

Use the Canon Multifunction Printer

Printing:

The printer is set up as a Windows printer. Just select the approriate Canon printer when printing.

Scanning and other functions:

Click start -

All Programs -

SX Virtual Link

- SX Virtual

Link.

Conrm " " (available).

Select the Canon multifunction printer and click Connect.

Conrm " " (connected).Refer to the operation manual of the Canon multifunction printer to use the scanner, card reader, and fax function.

To disconnect:

Important: One person can be connected with SX Virtual Link for scanning at a time. When you are done scanning, you should disconnect from the Canon multifunction printer in SX Virtual Link so it will be available for another PC to be able to connect.

Select the Canon multifunction printer and click

Disconnect.