www.silentcall.com
Silent Call® Communications Corporation
5095 Williams Lake Road
Waterford, Michigan 48329
Communications
Smartphone Docking Station
with Speaker and Bed Shaker
For use with any Smartphone or Tablet
User’s Manual
Smartphone not included.
TM
WARRANTY
The Silent Call AlarmDock is warranted for (see individual items for length
of warranty) from the day of purchase to be free of defects in material and
workmanship. This warranty is limited to free repair or replacement when
the product is shipped prepaid to:
Silent Call® Communications Corporation
5095 Williams Lake Road
Waterford, Michigan 48329
This warranty is void when damage is caused by misuse, neglect, fire,
excessive heat, water, or by improper installation or operation. Silent Call
will not be responsible for the cost of parts or labor and/or service charges
which are performed by others.
To obtain warranty service, call toll free 1-800-572-5227 or email us at
technicalsupport@silentcall.com
After this warranty expires, Silent Call will repair or replace any Silent
Call product for a fixed cost.
4
TABLE OF CONTENTS
Introduction........................................................................................4
Important Safety Instructions ............................................................... 4
Danger .............................................................................................. 4
Warnings ........................................................................................... 4
Precautions ........................................................................................ 4
Specifications USB Power Cube........................................................... 4
Smartphone Application Requirements ................................................. 4
Manual Reviews ................................................................................. 5
AlarmDock Specifications ................................................................... 5
AlarmDock Cradle, Model # AD100SM ................................................6
Application and Setup ......................................................................... 7
Bed Shaker, Model # VIB-PJ ................................................................ 7
Wireless Bed Shaker Module, # AD200-SM .........................................7
USB Charger/Power Cube, Model # 890010 ........................................ 8
Shaker Module Setup and Pairing ........................................................ 8
Pairing Instructions for the Bed Shaker ................................................ 9
FCC Statement ................................................................................... 9
AlarmDock Application Setup Icons ......................................................9
Troubleshooting Tips ......................................................................... 10
Warranty ..............................................................................back cover
INTRODUCTION
Thank you for choosing the AlarmDock™ Smartphone speaker. This instruction
manual contains useful information on appropriate use and maintenance of
this product. In order to benefit from its features, read this manual before
first use and save it for further reference.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS ESPECIALLY WHEN CHILDREN ARE
PRESENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING: Read all instructions before using this product.
DANGER:
• Do not let water or any other liquid or flammable detergent enter the
power jack to avoid electric shock and/ or fire hazard. Do not clean the
power cable with water or any other liquid or a (flammable) detergent to
avoid electric shock and/or a fire hazard.
• To prevent fire or shock hazard do not expose this product to water,
or moisture. Before connecting to the main power make sure that the
requirements specified on the power cube unit corresponds to the
available power. i.e. AC100-240V~, 50/60 Hz.
WARNINGS
• This product is not intended for use by children or persons with reduced
physical, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the unit by a person
responsible for their safety.
• Modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
PRECAUTIONS
Children should be supervised to ensure that they DO NOT play with
the unit especially the parts.
65
SPECIFICATIONS USB Power Cube
Switching type AC/DC Power Adapter, Rated Input: 100-240 Vac,
50/60 Hz, 0.8A
SMARTPHONE APPLICATION REQUIREMENTS
Androids: 4.0 or higher
iPhone: iOS 8 or later, compatible with iPhone, iPad, and iPod touch.
App size 2.4 MB.
THIS MANUAL REVIEWS PROPER CONNECTION AND USE OF:
• AlarmDock cradle with built-in speaker, Model # AD100SM
• Bed Shaker, Model # VIB-PJ
• Shaker Module, Model # AD200-SM
• USB Charger/ Power Cube, Model # 890010
• AlarmDock smartphone application (iOS and Android)
ALARMDOCK SPECIFICATIONS
Speakers: 2 x 40mm
Amplifier power: 2 x 4w
Frequency response: 150Hz - 20kHz
Signal-to-noise ratio: up to 100dB
Distortion: ≤5%
Battery type: polymer Li-ion
Wireless transmitter frequency range: 2.4–2.48GHz
Battery charging voltage: 5V
Battery charge time: 3-4 hours
Battery capacity: 1000 mAh
Wireless transmission distance: 33 feet
Dimensions: 6.2 x 4.2 x 5.6 inches
TM
1 ALARMDOCK CRADLE, MODEL # AD100SM, FEATURES: :
• 2-in-1, wireless speaker and phone stand
• Extra-loud alarm, up to 100 decibels
• Unique, patented design
• Touch-sensitive controls
• 2 broad-frequency response speakers
• Rich, 360°, crystal-clear sound
• Compatible with Android/IOS/Windows/MAC OS
• Built-in, rechargeable Li-ion battery provides up to 10 hours play time
• Wireless and audio (port) connections – aux. cord not included
• Memory pairing capability. Easy to operate
• Two-way USB port, plays and charges at the same time
• 90 day warranty
APPLICATION AND SETUP
You’ll need to download the AlarmDock™ application. For
Android’s go to the Google play store. For iPhone go to the
iTunes App Store. Type AlarmDock™ into the application
search field, then look for AlarmDock by Silent Call
®
Communications. Once you’ve downloaded the application,
you’ll need to open it to setup your alarm settings and to pair the wireless
bed shaker. To use the AlarmDock™ application one device at a minimum
must be paired for it to work. See application requirements under smartphone
application requirements above.
87
2 BED SHAKER, MODEL # VIB-PJ, 5 YEAR WARRANTY
Best placement for the bed shaker is under the mattress, between the
mattress and box spring. Place in a spot that would be closest to your
upper back. Once in place, plug the bed shaker into the end of the
Shaker Module input jack. Plug the Shaker Module into the USB charger
cube, then plug the USB charger cube into the 120 volt wall outlet.
Very important “DO NOT USE ANY OTHER MANFACTURERS BED SHAKER
WITH THE Shaker Module, IT COULD DAMAGE THE SHAKER MODULE
AND VOID THE WARRANTY”.
4 USB CHARGER/POWER CUBE, MODEL # 890010, 1 YEAR WARRANTY
The USB charger Cube is designed to power and charge up to four
devices at one time. Charge devices like the AlarmDock™ wireless
speaker stand, cell phones, & tablets. It also powers the wireless bed
shaker module.
3 BED SHAKER MODULE, # AD200-SM, 90 DAY WARRANTY
Plug the wireless bed shaker module into the USB charger cube. Plug the
USB charger cube into a 120 volt wall outlet. The USB charger cube will
keep the Shaker Module powered and ready to activate the bed shaker.
When the Shaker Module is in range, approximately 30 feet from your
smartphone it will automatically pair itself to the smartphone. A blue light
on the Shaker Module will light up and flash on & off when ready to be
paired. When paired the blue light will stay steady, no flashing.
SHAKER MODULE SETUP AND PAIRING
Plug the bed shaker jack into the jack input at the end of the Shaker Module.
Next plug the Shaker Module into the USB Charger Cube and plug the USB
Charger Cube into any 120 volt outlet. Make sure the jack on the bed
shaker is pushed all the way into the Shaker Module. Place the bed shaker
between the mattress and box spring of your bed. For best result, place
the bed shaker under the area where your upper back would be positioned
when in bed.
Note: Different diagram
needed
109
PAIRING INSTRUCTIONS FOR THE BED SHAKER
Bed Shaker Pairing: Once your smartphone is in range of the Bed Shaker
approximately 30' or less the Bed Shaker will automatically pair with your
smartphone. A blue flashing indicator light will flash on the Shaker Module
stick and will change to steady lit no flashing when paired. If the blue LED
is still flashing, you’ll need to turn on the Bluetooth setting in your phones
settings.
ALARMDOCK™ APPLICATION SETUP ICONS
(LOCATED AT THE BOTTOM OF THE APP)
There are five icons located at the bottom of the application, below we
explain each individually.
Connect icon (pairing the wireless bed shaker/Vibrator Shaker Module)
Connect icon (pairing with AlarmDock wireless cradle)
Alarm Icon – Tap on the Alarm icon, then tap the + at the top right corner
to setup an alarm. Follow the app instructions. Here you can set multiple
alarms, repeat the alarms with days of the week selections. You can name
the alarm with labels, select the sound type, volume control, tone control,
and select an alarm fade option from 10 seconds to 5 minutes or none.
Timer icon – Tap the Timer icon to set a timer.
Clock Icon with Swipe to Dim Feature – Tap on the Clock icon swipe
on the display screen in either direction to select from eight different display
colors. Once the color has been selected you can dim the display by swiping
left to right or top to bottom.
Settings (located at the bottom right-hand side) – To leave the clock display,
tap anywhere on the screen. Tap settings to see all the choices available.
Adjust the volume, vibration strength. Select how you want to be alerted,
Sound, vibrator or your phones flashing light. Adjust the snooze duration from
5 minutes to 50 minutes, and select the preferred time format 12/24 hour.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly approved by
Silent Call Communications may void the FCC authorization to operate this device.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
1211
Problem Solution
Wireless
connection
cannot be
established
• Make sure that the audio cable has been removed from
the AUX IN jack of your wireless speaker.
• If the connection fails when making a wireless
connection between the speaker and your wireless
device for the first time, turn off your AlarmDock unit,
then turn it on again to clear the device name, then
try the connection again.
Wireless
Shaker
Module won’t
stop flashing
• Turn on your Bluetooth setting in your phones settings.
Also make sure your phone is in range, 30' or less.
Sound,
vibration or
flashing light
not working
• Go to the app settings icon and turn on the alert.
Wireless
vibe/bed
shaker too
weak or not
working
• Go to settings and slide the vibration slider to the right.
• Check that the Bed Shaker plugged in all the way to
the Shaker Module.
• Make sure that the Shaker Module is plugged in all the
way on the power/charger cube.
Problem Solution
No power • Make sure that the USB charging line is correctly
connected.
• The built-in lithium battery may be drained. Charge the
battery by connecting the USB charger.
No sound
output via
wireless
• Make sure your wireless device is properly connected
to the speaker.
• Make sure that the volume level of your AlarmDock
device is not set to the minimum.
• Make sure that the volume level of your wireless device
connected to the speaker is not set to the minimum.
• Make sure that your wireless device is not muted.
• Make sure that your stereo audio cable is not
connected to the AUX IN jack of the speaker.
No sound
output in
AUX IN mode
• Make sure that the AUX cable is undamaged and firmly
connected to the AlarmDock device.
• Make sure that the volume level of the speaker is
not set to the minimum.
• Make sure that the volume level of the connected
external device is not set to the minimum.
Low battery
warning
• When the battery is low, the indicator light will turn red
and an alert will sound. Use the USB cable for charging.
• The internal battery is drained. Charge the battery or
connect the USB charger and turn on the system again.
TROUBLESHOOTING TIPS
Please read this User Guide carefully before using your wireless speaker.
Check this list for a possible troubleshooting solution before calling
for service.
Loading...